Datenblatt für User Equipment (UE) AT Commands

ETSI TS 127 007 1 telecomm tions system (Phase 2+) (GSM); Telecommunications System ( MTS); command set for User Equipment (UE) (36PP TS 27.0 rsion 13.3.0 Release 1 an“ $68 l.e A aLuIAI INITIATIVE
ETSI TS
1
Digital cellular telecomm
Universal Mobile Tel
AT command
(
3GPP TS 27.0
TECHNICAL
SPECIFICATION
V13.3.0 (
2016
mmunications system (Phase
elecommunications System (
LTE;
d set for User Equipment (UE
.007 version 13.3.0 Release 13
ION
16
-03)
e 2+) (GSM);
(UMTS);
E)
13
)
htth/www etsi.urg/standards-search htth/Qurtal .elsi .org/Ib/status/status.asg httgs.//Qurtal.etsi org/FeaQIe/CommiteeSuQQortStaflasgx
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
1
3GPP TS 27.007 version 13.3.0 Release 13
Reference
RTS/TSGC-0127007vd30
Keywords
GSM, LTE, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any
electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
DECT
TM
, PLUGTESTS
TM
, UMTS
TM
and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
3GPP
TM
and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
2
3GPP TS 27.007 version 13.3.0 Release 13
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
http://webapp.etsi.org/key/queryform.asp.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
3
3GPP TS 27.007 version 13.3.0 Release 13
Contents
Intellectual Property Rights ................................................................................................................................ 2
Foreword ............................................................................................................................................................. 2
Modal verbs terminology .................................................................................................................................... 2
Foreword ............................................................................................................................................................. 9
1 Scope ...................................................................................................................................................... 10
2 References .............................................................................................................................................. 10
3 Definitions and abbreviations ................................................................................................................. 17
3.1 Definitions ........................................................................................................................................................ 17
3.2 Abbreviations ................................................................................................................................................... 17
4 AT command syntax .............................................................................................................................. 18
4.0 General ............................................................................................................................................................. 18
4.1 Command line .................................................................................................................................................. 18
4.2 Information responses and result codes ............................................................................................................ 19
4.3 ITU-T Recommendation V.250 [14] TE-TA interface commands .................................................................. 19
5 General commands ................................................................................................................................. 20
5.0 General ............................................................................................................................................................. 20
5.1 Request manufacturer identification +CGMI ................................................................................................... 20
5.2 Request model identification +CGMM ............................................................................................................ 21
5.3 Request revision identification +CGMR .......................................................................................................... 21
5.4 Request product serial number identification +CGSN ..................................................................................... 22
5.5 Select TE character set +CSCS ........................................................................................................................ 23
5.6 Request international mobile subscriber identity +CIMI ................................................................................. 24
5.7 Multiplexing mode +CMUX ............................................................................................................................ 25
5.8 ITU-T Recommendaton V.250 [14] generic TA control commands ................................................................ 27
5.9 PCCA STD-101 [17] select wireless network +WS46 ..................................................................................... 27
5.10 Informative examples ....................................................................................................................................... 28
6 Call control commands and methods ..................................................................................................... 29
6.0 General ............................................................................................................................................................. 29
6.1 Select type of address +CSTA .......................................................................................................................... 29
6.2 ITU-T Recommendation V.250 [14] dial command D ..................................................................................... 30
6.3 Direct dialling from phonebooks ...................................................................................................................... 30
6.4 Call mode +CMOD .......................................................................................................................................... 32
6.4A Voice call mode +CVMOD .............................................................................................................................. 32
6.5 Hangup call +CHUP ......................................................................................................................................... 33
6.6 Alternating mode call control method .............................................................................................................. 34
6.7 Select bearer service type +CBST .................................................................................................................... 35
6.8 Radio link protocol +CRLP .............................................................................................................................. 38
6.9 Service reporting control +CR.......................................................................................................................... 39
6.10 Extended error report +CEER .......................................................................................................................... 39
6.11 Cellular result codes +CRC .............................................................................................................................. 40
6.12 HSCSD device parameters +CHSD ................................................................................................................. 42
6.13 HSCSD transparent call configuration +CHST ................................................................................................ 43
6.14 HSCSD non-transparent call configuration +CHSN ........................................................................................ 43
6.15 HSCSD current call parameters +CHSC .......................................................................................................... 44
6.16 HSCSD parameters report +CHSR .................................................................................................................. 45
6.17 HSCSD automatic user initiated upgrading +CHSU ........................................................................................ 45
6.18 HSCSD non-transparent asymmetry configuration +CHSA ............................................................................ 46
6.19 Single numbering scheme +CSNS ................................................................................................................... 47
6.20 Voice hangup control +CVHU ......................................................................................................................... 47
6.21 CCITT V.120 [36] rate adaption protocol +CV120 ......................................................................................... 48
6.22 Settings date format +CSDF ............................................................................................................................. 49
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
4
3GPP TS 27.007 version 13.3.0 Release 13
6.23 Silence command +CSIL .................................................................................................................................. 50
6.24 Settings time format +CSTF ............................................................................................................................. 51
6.25 ITU-T Recommendation V.250 [14] call control commands ........................................................................... 52
6.26 ITU-T Recommendation V.250 [14] data compression commands ................................................................. 52
6.27 Initiate eCall +CECALL .................................................................................................................................. 52
6.28 Informative examples ....................................................................................................................................... 53
7 Network service related commands ....................................................................................................... 54
7.0 General ............................................................................................................................................................. 54
7.1 Subscriber number +CNUM ............................................................................................................................ 54
7.2 Network registration +CREG ........................................................................................................................... 55
7.3 PLMN selection +COPS .................................................................................................................................. 57
7.4 Facility lock +CLCK ........................................................................................................................................ 59
7.5 Change password +CPWD ............................................................................................................................... 61
7.6 Calling line identification presentation +CLIP ................................................................................................. 61
7.7 Calling line identification restriction +CLIR .................................................................................................... 63
7.8 Connected line identification presentation +COLP .......................................................................................... 64
7.9 Called line identification presentation +CDIP .................................................................................................. 65
7.10 Closed user group +CCUG ............................................................................................................................... 66
7.11 Call forwarding number and conditions +CCFC .............................................................................................. 67
7.12 Call waiting +CCWA ....................................................................................................................................... 68
7.13 Call related supplementary services +CHLD ................................................................................................... 70
7.14 Call deflection +CTFR ..................................................................................................................................... 71
7.15 Unstructured supplementary service data +CUSD ........................................................................................... 72
7.16 Advice of charge +CAOC ................................................................................................................................ 73
7.17 Supplementary service notifications +CSSN ................................................................................................... 74
7.18 List current calls +CLCC ................................................................................................................................. 76
7.19 Preferred PLMN list +CPOL ............................................................................................................................ 77
7.20 Selection of preferred PLMN list +CPLS......................................................................................................... 79
7.21 Read operator names +COPN .......................................................................................................................... 80
7.22 eMLPP priority registration and interrogation +CAEMLPP ............................................................................ 80
7.23 eMLPP subscriptions +CPPS ........................................................................................................................... 81
7.24 Fast call setup conditions +CFCS..................................................................................................................... 81
7.25 Automatic answer for eMLPP service +CAAP ................................................................................................ 82
7.26 User to user signalling service 1 +CUUS1 ....................................................................................................... 82
7.27 Preferred network indication +CPNET ............................................................................................................ 84
7.28 Preferred network status +CPNSTAT .............................................................................................................. 85
7.29 Current packet switched bearer +CPSB ........................................................................................................... 85
7.30 Calling name identification presentation +CNAP ............................................................................................ 87
7.31 Connected line identification restriction status +COLR ................................................................................... 88
7.32 Service specific access control restriction status +CSSAC .............................................................................. 88
7.33 Network emergency bearer services support +CNEM ..................................................................................... 90
7.34 Enhanced closed user group +CECUG ............................................................................................................ 91
7.35 Communication forwarding number and conditions with URI support +CCFCU ........................................... 93
7.36 Message waiting indication control +CMWI ................................................................................................... 94
7.37 Session start and stop for smart congestion mitigation +CSCM ...................................................................... 95
7.38 Power Saving Mode Setting +CPSMS ............................................................................................................. 96
7.39 Application Start and Stop indication for ACDC +CACDC ............................................................................ 98
7.40 Informative examples ....................................................................................................................................... 98
8 Mobile termination control and status commands ................................................................................ 100
8.0 General ........................................................................................................................................................... 100
8.1 Phone activity status +CPAS .......................................................................................................................... 101
8.2 Set phone functionality +CFUN ..................................................................................................................... 102
8.3 Enter PIN +CPIN ........................................................................................................................................... 103
8.4 Battery charge +CBC ..................................................................................................................................... 105
8.5 Signal quality +CSQ ....................................................................................................................................... 105
8.6 Mobile termination control mode +CMEC .................................................................................................... 106
8.7 Keypad control +CKPD ................................................................................................................................. 107
8.8 Display control +CDIS ................................................................................................................................... 108
8.9 Indicator control +CIND ................................................................................................................................ 109
8.10 Mobile termination event reporting +CMER ................................................................................................. 110
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
5
3GPP TS 27.007 ve
rsion 13.3.0 Release 13
8.11 Select phonebook memory storage +CPBS .................................................................................................... 113
8.12 Read phonebook entries +CPBR .................................................................................................................... 114
8.13 Find phonebook entries +CPBF ..................................................................................................................... 115
8.14 Write phonebook entry +CPBW .................................................................................................................... 118
8.15 Clock +CCLK ................................................................................................................................................ 119
8.16 Alarm +CALA................................................................................................................................................ 120
8.17 Generic SIM access +CSIM ........................................................................................................................... 121
8.18 Restricted SIM access +CRSM ...................................................................................................................... 122
8.19 Secure control command +CSCC ................................................................................................................... 123
8.20 Alert sound mode +CALM ............................................................................................................................. 124
8.21 Ringer sound level +CRSL ............................................................................................................................. 124
8.22 Vibrator mode +CVIB .................................................................................................................................... 125
8.23 Loudspeaker volume level +CLVL ................................................................................................................ 126
8.24 Mute control +CMUT .................................................................................................................................... 126
8.25 Accumulated call meter +CACM ................................................................................................................... 127
8.26 Accumulated call meter maximum +CAMM ................................................................................................. 127
8.27 Price per unit and currency table +CPUC ...................................................................................................... 128
8.28 Call meter maximum event +CCWE .............................................................................................................. 128
8.29 Power class +CPWC ...................................................................................................................................... 129
8.30 Set language +CLAN ..................................................................................................................................... 130
8.31 Language event +CLAE ................................................................................................................................. 131
8.32 Set greeting text +CSGT ................................................................................................................................ 131
8.33 Set voice mail number +CSVM ..................................................................................................................... 132
8.34 Ring melody control +CRMC ........................................................................................................................ 133
8.35 Ring melody playback +CRMP...................................................................................................................... 134
8.36 Master reset +CMAR ..................................................................................................................................... 134
8.37 List all available AT commands +CLAC ....................................................................................................... 135
8.38 Delete alarm +CALD ..................................................................................................................................... 135
8.39 Postpone or dismiss an alarm +CAPD ........................................................................................................... 136
8.40 Automatic time zone update +CTZU ............................................................................................................. 136
8.41 Time zone reporting +CTZR .......................................................................................................................... 137
8.42 Enter protocol mode+CPROT ........................................................................................................................ 138
8.43 Generic UICC logical channel access +CGLA .............................................................................................. 139
8.44 Restricted UICC logical channel access +CRLA ........................................................................................... 140
8.45 Open logical channel +CCHO ........................................................................................................................ 142
8.46 Close logical channel +CCHC........................................................................................................................ 142
8.47 EAP authentication +CEAP ........................................................................................................................... 143
8.48 EAP retrieve parameters +CERP .................................................................................................................... 145
8.49 UICC application discovery +CUAD ............................................................................................................. 145
8.50 Mobile originated location request +CMOLR ................................................................................................ 146
8.51 Backlight +CBKLT ........................................................................................................................................ 150
8.52 Command touch screen action +CTSA .......................................................................................................... 151
8.53 Command screen orientation +CSO ............................................................................................................... 153
8.54 Command screen size +CSS ........................................................................................................................... 155
8.54A Command display screen boundary +CDSB .................................................................................................. 156
8.55 Positioning control +CPOS ............................................................................................................................ 156
8.56 Positioning reporting +CPOSR ...................................................................................................................... 172
8.57 Mobile terminated location request notification +CMTLR ............................................................................ 173
8.58 Mobile terminated location request disclosure allowance +CMTLRA .......................................................... 175
8.59 Battery capacity +CBCAP .............................................................................................................................. 175
8.60 Battery connection status +CBCON ............................................................................................................... 176
8.61 Battery charger status +CBCHG .................................................................................................................... 177
8.62 Printing IP address format +CGPIAF ............................................................................................................. 177
8.63 IMS single radio voice call continuity +CISRVCC ....................................................................................... 179
8.64 IMS network reporting +CIREP ..................................................................................................................... 179
8.65 Remaining PIN retries +CPINR ..................................................................................................................... 180
8.66 Set card slot +CSUS ....................................................................................................................................... 181
8.67 Emergency numbers +CEN ............................................................................................................................ 182
8.68 Availability for voice calls with IMS +CAVIMS........................................................................................... 183
8.69 Extended signal quality +CESQ ..................................................................................................................... 183
8.70 Primary notification event reporting +CPNER .............................................................................................. 185
8.71 IMS registration information +CIREG ........................................................................................................... 186
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
6
3GPP TS 27.007 version 13.3.0 Release 13
8.72 Availability for SMS using IMS +CASIMS................................................................................................... 187
8.73 Monitor of current calls +CMCCS ................................................................................................................. 188
8.74 List of current calls +CLCCS ......................................................................................................................... 194
8.75 Supported radio accesses +CSRA .................................................................................................................. 197
8.76 Circuit switched fallback +CCSFB ................................................................................................................ 199
8.77 Informative examples ..................................................................................................................................... 200
9 Mobile termination errors ..................................................................................................................... 204
9.1 Report mobile termination error +CMEE ....................................................................................................... 204
9.1A Report mobile originated location request error +CMOLRE ......................................................................... 204
9.1B Report network error codes +CNEC .............................................................................................................. 205
9.2 Mobile termination error result code +CME ERROR .................................................................................... 206
9.2.0 General ...................................................................................................................................................... 206
9.2.1 General errors ........................................................................................................................................... 207
9.2.2 GPRS and EPS-related errors ................................................................................................................... 208
9.2.2.1 Errors related to a failure to perform an attach.................................................................................... 208
9.2.2.2 Errors related to a failure to activate a context .................................................................................... 208
9.2.2.3 Errors related to a failure to disconnect a PDN ................................................................................... 209
9.2.2.4 Other GPRS errors .............................................................................................................................. 209
9.2.3 VBS, VGCS and eMLPP-related errors .................................................................................................... 209
9.3 Mobile termination error result code +CMOLRE .......................................................................................... 209
9.3.1 General ...................................................................................................................................................... 209
9.3.2 Errors ........................................................................................................................................................ 210
9.4 Informative examples ..................................................................................................................................... 210
10 Commands for packet domain .............................................................................................................. 210
10.0 General ........................................................................................................................................................... 210
10.1 Commands specific to MTs supporting the packet domain ............................................................................ 211
10.1.0 General remark about EPS bearer contexts and PDP contexts ................................................................. 211
10.1.1 Define PDP context +CGDCONT ............................................................................................................ 212
10.1.2 Define secondary PDP context +CGDSCONT ......................................................................................... 216
10.1.3 Traffic flow template +CGTFT ................................................................................................................ 218
10.1.4 Quality of service profile (requested) +CGQREQ .................................................................................... 221
10.1.5 Quality of service profile (minimum acceptable) +CGQMIN .................................................................. 223
10.1.6 3G quality of service profile (requested) +CGEQREQ ............................................................................ 224
10.1.7 3G quality of service profile (minimum acceptable) +CGEQMIN ........................................................... 227
10.1.8 3G quality of service profile (negotiated) +CGEQNEG ........................................................................... 231
10.1.9 PS attach or detach +CGATT ................................................................................................................... 233
10.1.10 PDP context activate or deactivate +CGACT ........................................................................................... 233
10.1.11 PDP context modify +CGCMOD ............................................................................................................. 234
10.1.12 Enter data state +CGDATA ...................................................................................................................... 235
10.1.13 Configure local octet stream PAD parameters +CGCLOSP (Obsolete) ................................................... 237
10.1.14 Show PDP address(es) +CGPADDR ........................................................................................................ 237
10.1.15 Automatic response to a network request for PDP context activation +CGAUTO .................................. 238
10.1.16 Manual response to a network request for PDP context activation +CGANS .......................................... 239
10.1.17 GPRS mobile station class +CGCLASS ................................................................................................... 240
10.1.18 Configure local triple-X PAD parameters +CGCLPAD (GPRS only) (Obsolete) ................................... 241
10.1.19 Packet domain event reporting +CGEREP ............................................................................................... 241
10.1.20 GPRS network registration status +CGREG ............................................................................................ 245
10.1.21 Select service for MO SMS messages +CGSMS ...................................................................................... 248
10.1.22 EPS network registration status +CEREG ................................................................................................ 248
10.1.23 PDP context read dynamic parameters +CGCONTRDP .......................................................................... 251
10.1.24 Secondary PDP context read dynamic parameters +CGSCONTRDP ...................................................... 253
10.1.25 Traffic flow template read dynamic parameters +CGTFTRDP ................................................................ 254
10.1.26 Define EPS quality of service +CGEQOS ................................................................................................ 256
10.1.27 EPS quality of service read dynamic parameters +CGEQOSRDP ........................................................... 257
10.1.28 UE modes of operation for EPS +CEMODE ............................................................................................ 258
10.1.29 Delete non-active PDP contexts +CGDEL ............................................................................................... 259
10.1.30 Signalling connection status +CSCON ..................................................................................................... 259
10.1.31 Define PDP context authentication parameters +CGAUTH ..................................................................... 261
10.1.32 Initial PDP context activation +CIPCA .................................................................................................... 262
10.1.33 No more PS data +CNMPSD .................................................................................................................... 262
13
ETSI
ETSI TS 127
007 V13.3.0 (2016
-
03)
7
3GPP TS 27.007 version 13.3.0 Release 13
10.1.34 UE's usage setting for EPS +CEUS .......................................................................................................... 263
10.1.35 UE's Voice Domain Preference E-UTRAN +CEVDP .............................................................................. 263
10.1.36 UE's Voice Domain Preference UTRAN +CVDP .................................................................................... 264
10.1.37 UE's Mobility Management IMS Voice Termination +CMMIVT ........................................................... 265
10.1.38 Power Preference Indication for EPS +CEPPI ......................................................................................... 265
10.1.39 WLAN offload assistance data +CWLANOLAD..................................................................................... 266
10.1.40 WLAN offload cell measurement +CWLANOLCM ................................................................................ 268
10.2 Modem compatibility commands ................................................................................................................... 269
10.2.0 General ...................................................................................................................................................... 269
10.2.1 MT originated PDP context activation...................................................................................................... 269
10.2.1.0 General ................................................................................................................................................ 269
10.2.1.1 Request packet domain service 'D' ...................................................................................................... 269
10.2.1.2 Request packet domain IP service 'D' ................................................................................................. 270
10.2.2 Network requested PDP context activation .............................................................................................. 271
10.2.2.0 General ................................................................................................................................................ 271
10.2.2.1 Automatic response to a network request for PDP context activation 'S0' .......................................... 271
10.2.2.2 Manual acceptance of a network request for PDP context activation 'A' ............................................ 272
10.2.2.3 Manual rejection of a network request for PDP context activation 'H' ............................................... 272
11 Commands for VGCS and VBS ........................................................................................................... 272
11.0 General ........................................................................................................................................................... 272
11.1 Commands specific to MTs supporting the VGCS and VBS ......................................................................... 272
11.1.1 Accept an incoming voice group or voice broadcast call +CAJOIN ........................................................ 272
11.1.2 Reject an incoming voice group or voice broadcast call +CAREJ ........................................................... 273
11.1.3 Leave an ongoing voice group or voice broadcast call +CAHLD ............................................................ 274
11.1.4 Talker access for voice group call +CAPTT ............................................................................................. 274
11.1.5 Voice group call uplink status presentation +CAULEV ........................................................................... 275
11.1.6 List current voice group and voice broadcast calls +CALCC ................................................................... 275
11.1.7 Voice group or voice broadcast call state attribute presentation +CACSP ............................................... 277
11.1.8 NCH support indication +CANCHEV ...................................................................................................... 278
11.1.9 Originator to dispatcher information +COTDI ......................................................................................... 278
11.1.10 Short data transmission during ongoing VGCS +CEPTT ......................................................................... 279
11.1.11 Group Id prefixes capability +CGIPC ...................................................................................................... 280
11.2 Modem compatibility commands ................................................................................................................... 281
11.2.0 General ...................................................................................................................................................... 281
11.2.1 Request VGCS or VBS service 'D' ........................................................................................................... 281
11.2.2 Termination of an voice group or voice broadcast call 'H' ........................................................................ 282
11.3.1 VGCS subscriptions and GId status +CGCS ............................................................................................ 282
11.3.2 VBS subscriptions and GId status +CBCS ............................................................................................... 283
11.4 Informative examples ..................................................................................................................................... 283
12 Commands for USIM application toolkit ............................................................................................. 284
12.1 General ........................................................................................................................................................... 284
12.2 Commands specific to MTs supporting USAT .............................................................................................. 284
12.2.1 Read USAT profile +CUSATR ................................................................................................................ 284
12.2.2 Write USAT profile +CUSATW .............................................................................................................. 285
12.2.3 Profile download upon start-up +CUSATD.............................................................................................. 286
12.2.4 Activate USAT profile +CUSATA ........................................................................................................... 287
12.2.5 Send USAT terminal response +CUSATT ............................................................................................... 289
12.2.6 Send USAT envelope command +CUSATE ............................................................................................ 289
12.3 Informative examples ..................................................................................................................................... 290
13 Commands for enhanced support of dialling........................................................................................ 292
13.1 General ........................................................................................................................................................... 292
13.2 Commands for dialling ................................................................................................................................... 292
13.2.1 Dial URI +CDU ........................................................................................................................................ 292
13.2.2 Dial URI from phonebook +CDUP .......................................................................................................... 295
13.2.3 Hangup of current calls +CHCCS............................................................................................................. 296
13.2.4 Define media profile +CDEFMP .............................................................................................................. 297
13.2.5 Control and modify media description +CCMMD ................................................................................... 298
13.3 Informative examples ..................................................................................................................................... 299
14 Commands for eMBMS configuration ................................................................................................. 303
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
8
3GPP TS 27.007 version 13.3.0 Release 13
14.1 General ........................................................................................................................................................... 303
14.2 Commands specific to eMBMS ...................................................................................................................... 303
14.2.1 eMBMS configuration in MT +CEMBMSCFG ....................................................................................... 303
14.2.2 eMBMS status reporting in MT +CEMBMSR ......................................................................................... 304
14.2.3 eMBMS service configuration +CEMBMSSRV ...................................................................................... 305
14.2.4 Enter eMBMS data state +CEMBMSDATA ............................................................................................ 306
14.2.5 eMBMS counting procedure +CEMBMSCNT ......................................................................................... 306
14.2.6 eMBMS Service Area Identities +CEMBMSSAI..................................................................................... 307
Annex A (normative): Summary of commands from other standards ......................................... 309
Annex B (normative): Summary of result codes ............................................................................. 311
Annex C (informative): Commands from TIA IS-101 ...................................................................... 313
C.1 Introduction .......................................................................................................................................... 313
C.2 Commands ............................................................................................................................................ 314
C.2.1 Select mode +FCLASS .................................................................................................................................. 314
C.2.2 Buffer threshold setting +VBT ....................................................................................................................... 314
C.2.3 Calling number ID presentation +VCID ........................................................................................................ 315
C.2.4 Receive gain selection +VGR ........................................................................................................................ 315
C.2.5 Transmit gain selection +VGT ....................................................................................................................... 315
C.2.6 Initialise voice parameters +VIP .................................................................................................................... 316
C.2.7 Inactivity timer +VIT ..................................................................................................................................... 316
C.2.8 Line selection +VLS ....................................................................................................................................... 316
C.2.9 Receive data state +VRX ............................................................................................................................... 318
C.2.10 Select compression method +VSM ................................................................................................................ 318
C.2.11 DTMF and tone generation +VTS .................................................................................................................. 319
C.2.12 Tone duration +VTD ...................................................................................................................................... 319
C.2.13 Transmit data state +VTX .............................................................................................................................. 320
Annex D (informative): Bibliography ................................................................................................. 321
Annex E (informative): Mobile originated alternating voice/data call example ............................. 322
Annex F (informative): Mobile terminated voice followed by data call example ........................... 323
Annex G (informative): Voice call example ........................................................................................ 324
Annex H (informative): Change history ............................................................................................. 325
History ............................................................................................................................................................ 331
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
9
3GPP TS 27.007 version 13.3.0 Release 13
Foreword
This Technical Specification (TS) has been produced by the 3
rd
Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
10
3GPP TS 27.007 version 13.3.0 Release 13
1 Scope
The present document specifies a profile of AT commands and recommends that this profile be used for controlling
Mobile Termination (MT) functions and GSM/UMTS network services from a Terminal Equipment (TE) through
Terminal Adaptor (TA). The command prefix +C is reserved for Digital Cellular in
ITU-T Recommendation V.250 [14]. The present document has also the syntax details used to construct these extended
GSM/UMTS commands. Commands from ITU-T Recommendation V.250 [14] and existing digital cellular standards
(TIA IS-99 [15] and TIA IS-135 [16]) are used whenever applicable. Some of the new commands are defined such way
that they can be easily applied to MT of networks other than GSM/UMTS. ITU-T Recommendation T.31 [11] and ITU-
T Recommendation T.32 [12] fax AT commands may be used for GSM/UMTS fax transmission from TE. GSM/UMTS
Short Message Service AT commands are defined in 3GPP TS 27.005 [24]. AT commands for GPRS and EPC are
defined in clause 10 of this specification. The present document assumes an abstract architecture comprising a TE (e.g.
a computer) and a MT interfaced by a TA (see figure 1). The span of control of the defined commands should allow
handling of any physical implementation that this abstract architecture may lead to:
- TA, MT and TE as three separate entities;
- TA integrated under the MT cover, and the TE implemented as a separate entity;
- TA integrated under the TE cover, and the MT implemented as a separate entity; and
- TA and MT integrated under the TE cover as a single entity.
The commands described in the present document may be observed on the link between the TE and the TA. However,
most of the commands retrieve information about the MT, not about the TA.
Figure 1: Setup
Interface between TE and TA is intended to operate over existing serial (ITU-T Recommendation V.24) cables, infrared
link, and all link types with similar behaviour. For correct operation many of the defined commands require eight bit
data and therefore it is recommended that TE-TA link is set to eight bits/ byte mode. (For infrared operation
implementation, refer informative references IrDA. For embedding AT commands and data during on-line data state,
refer TIA-617/ITU-T V.80.) Interface between TA and MT is dependent on the interface in the MT.
The functional blocks shown in figure 1, using AT commands, shall follow the principles described in the interactions
handling framework 3GPP TS 23.227 [63].
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
- For a specific reference, subsequent revisions do not apply.
TE TA MT
AT cmds
responses
MT control
MT status
USER & APPLICATIONS NETWORK
network messages
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
11
3GPP TS 27.007 version 13.3.0 Release 13
- For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
[1] 3GPP TS 22.002: "Bearer Services (BS) supported by a GSM Public Land Mobile Network
(PLMN)".
[2] 3GPP TS 22.003: "Teleservices supported by a GSM Public Land Mobile Network (PLMN)".
[3] 3GPP TS 22.081: "Line identification supplementary services - Stage 1".
[4] 3GPP TS 22.082: "Call Forwarding (CF) supplementary services - Stage 1".
[5] 3GPP TS 22.083: "Call Waiting (CW) and Call Hold (HOLD) supplementary services - Stage 1".
[6] 3GPP TS 22.088: "Call Barring (CB) supplementary services - Stage 1".
[7] 3GPP TS 23.003: "Numbering, addressing and identification".
[8] 3GPP TS 24.008: "Mobile Radio Interface Layer 3 specification; Core Network Protocols-
Stage 3".
[9] GSM MoU SE.13, GSM MoU Permanent Reference Document SE.13: "GSM Mobile Network
Codes and Names".
[10] ITU-T Recommendation E.212: "Identification plan for land mobile stations".
[11] ITU-T Recommendation T.31: "Asynchronous facsimile DCE control, service class 1".
[12] ITU-T Recommendation T.32: "Asynchronous facsimile DCE control, service class 2".
[13] ITU-T Recommendation T.50: "International Reference Alphabet (IRA) (Formerly International
Alphabet No. 5 or IA5) - Information technology - 7-bit coded character set for information
exchange".
[14] ITU-T Recommendation V.250: "Serial asynchronous automatic dialling and control".
[15] TIA IS-99: "Data Services Option Standard for Wideband Spread Spectrum Digital Cellular
System".
[16] TIA IS-135: "800 MHz Cellular Systems, TDMA Services, Async Data and Fax".
[17] PCCA STD-101 Data Transmission Systems and Equipment: "Serial Asynchronous Automatic
Dialling and Control for Character Mode DCE on Wireless Data Services".
[18] 3GPP TS 24.022: "Radio Link Protocol (RLP) for data and telematic services on the Mobile
Station - Base Station System (MS - BSS) interface and the Base Station System - Mobile-services
Switching Centre (BSS - MSC) interface".
[19] 3GPP TS 22.030: "Man Machine Interface (MMI) of the Mobile Station (MS)".
[20] 3GPP TS 45.008: "Radio subsystem link control".
[21] 3GPP TS 22.085: "Closed User Group (CUG) supplementary services - Stage 1".
[22] 3GPP TS 22.084: "MultiParty (MPTY) supplementary services - Stage 1".
[23] 3GPP TS 22.090: "Unstructured Supplementary Service Data (USSD) - Stage 1".
[24] 3GPP TS 27.005: "Use of Data Terminal Equipment - Data Circuit terminating Equipment (DTE -
DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS)".
[25] 3GPP TS 23.038: "Alphabet and language specific information".
[26] 3GPP TS 22.024: "Description of Charge Advice Information (CAI)".
[27] 3GPP TS 22.086: "Advice of Charge (AoC) supplementary services - Stage 1".
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
1
2
3GPP TS 27.007 version 13.3.0 Release 13
[28] 3GPP TS 51.011: "Specification of the Subscriber Identity Module - Mobile Equipment (SIM-ME)
interface".
[29] 3GPP TS 22.034: "High Speed Circuit Switched Data (HSCSD) - Stage 1".
[30] 3GPP TS 22.091: "Explicit Call Transfer (ECT) supplementary service - Stage 1".
[31] 3GPP TS 22.072: "Call Deflection (CD) supplementary service - Stage 1".
[32] ISO/IEC 10646: "Universal Multiple-Octet Coded Character Set (UCS)"; UCS2, 16 bit coding.
[33] 3GPP TS 22.022: "Personalization of GSM Mobile Equipment (ME) Mobile functionality
specification".
[34] 3GPP TS 27.060: "General requirements on Mobile Stations (MS) supporting General Packet
Radio Bearer Service (GPRS)".
[35] Void.
[36] CCITT Recommendation V.120: "Support by an ISDN of data terminal equipment with V-Series
type interfaces with provision for statistical multiplexing".
[37] Void.
[38] 3GPP TS 45.005: "Radio transmission and reception".
[39] 3GPP TS 29.061: "Interworking between the Public Land Mobile Network (PLMN) supporting
GPRS and Packet Data Networks (PDN)".
[40] 3GPP TS 23.081: "Line identification supplementary services - Stage 2".
[41] 3GPP TS 27.001: "General on Terminal Adaptation Functions (TAF) for Mobile Stations (MS)".
[42] 3GPP TS 29.007: "General requirements on interworking between the Public Land Mobile
Network (PLMN) and the Integrated Services Digital Network (ISDN) or Public Switched
Telephone Network (PSTN)".
[43] Infrared Data Association; Specification of Ir Mobile Communications (IrMC).
[44] IrDA Object Exchange Protocol.
[45] 3GPP TS 27.010: "Terminal Equipment to User Equipment (TE-UE) multiplexer protocol User
Equipment (UE)".
[46] 3GPP TS 23.107: "Quality of Service, Concept and Architecture".
[47] 3GPP TS 23.060: "General Packet Radio Service (GPRS) Service description; Stage 2".
[48] Void.
[49] 3GPP TS 43.068: "Voice Group Call service (VGCS) - Stage 2".
[50] 3GPP TS 43.069: "Voice Broadcast Service (VBS) - Stage 2".
[51] Void.
[52] 3GPP TS 44.068: "Voice Group Call service (VGCS) - Stage 3".
[53] 3GPP TS 44.069: "Voice Broadcast Service (VBS) - Stage 3".
[54] 3GPP TS 22.067: "enhanced Multi-Level Precedence and Pre-emption service (eMLPP) -
Stage 1".
[55] 3GPP TS 42.068: "Voice Group Call service (VGCS) - Stage 1".
[56] 3GPP TS 42.069: "Voice Broadcast Service (VBS) - Stage 1".
[57] Void.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
13
3GPP TS 27.007 version 13.3.0 Release 13
[58] 3GPP TS 22.087: "User-to-User Signalling (UUS) - Stage 1".
[59] 3GPP TS 31.102: "Characteristics of the Universal Subscriber Identity Module (USIM)
Application".
[60] ETSI TS 102 221 "Smart Cards; UICC-Terminal interface; Physical and logical characteristics
(Release 1999)".
[61] 3GPP TS 44.065: "Mobile Station (MS) – Serving GPRS Support Node (SGSN); Subnetwork
Dependent Convergence Protocol (SNDCP)".
[62] 3GPP TS 25.323: "Packet Data Convergence Protocol (PDCP)".
[63] 3GPP TS 23.227 "Applications and User interaction in the UE-Principles and specific
requirements".
[64] Void.
[65] 3GPP TS 31.101: "UICC-Terminal Interface; Physical and Logical Characteristics."
[66] ETSI TS 102 310: "Smart Cards; Extensible Authentication Protocol support in the UICC".
[67] Void.
[68] RFC 3748: "Extensible Authentication Protocol (EAP)".
[69] RFC 3629: "UTF-8, a transformation format of ISO 10646".
[70] 3GPP TS 44.318: "Generic Access (GA) to the A/Gb interface; Mobile GA interface layer 3
specification".
[71] 3GPP TS 44.060: "General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station
System (BSS) interface; Radio Link Control/Medium Access Control (RLC/MAC) protocol".
[72] 3GPP TS 25.308: "High Speed Downlink Packet Access (HSDPA): Overall Description; Stage 2".
[73] 3GPP TS 25.319: "Enhanced Uplink; Overall Description; Stage 2".
[74] 3GPP TS 25.331: "Radio Resource Control (RRC) protocol specification".
[75] 3GPP TS 24.216: "Communication Continuity Management Object (MO)".
[76] 3GPP TS 23.032: "Universal Geographical Area Description (GAD)".
[77] 3GPP TS 25.305 "User Equipment (UE) positioning in Universal Terrestrial Radio Access
Network (UTRAN); Stage 2".
[78] IEC 61162: "Maritime navigation and radio communication equipment and systems – Digital
interfaces".
[79] 3GPP TS 44.031: "Location Services (LCS); Mobile Station (MS) - Serving Mobile Location
Centre (SMLC), Radio Resource LCS Protocol (RRLP)".
[80] 3GPP TS 49.031: "Base Station System Application Part, LCS Extension (BSSAP-LE)".
[81] Void.
[82] 3GPP TS 23.401: "GPRS enhancements for E-UTRAN access".
[83] 3GPP TS 24.301: "Non-Access-Stratum (NAS) protocol for Evolved Packet System (EPS)".
[84] Void.
[85] 3GPP TS 23.203: "Policy and charging control architecture".
[86] 3GPP TS 36.331: "Evolved Universal Terrestrial Radio Access (E-UTRA); Radio Resource
Control (RRC); Protocol specification".
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
14
3GPP TS 27.007 version 13.3.0 Release 13
[87] 3GPP TS 24.173: "IMS multimedia telephony communication service and supplementary services;
Stage 3".
[88] RFC 4291: "IP Version 6 Addressing Architecture".
[89] 3GPP TS 24.229: "IP multimedia call control protocol based on Session Initiation Protocol (SIP)
and Session Description Protocol (SDP)".
[90] 3GPP TS 23.221: "Architectural requirements".
[91] 3GPP TS 24.237: "IP Multimedia Subsystem (IMS) Service Continuity".
[92] 3GPP TS 31.111: "Universal Subscriber Identity Module (USIM) Application Toolkit (USAT)".
[93] 3GPP TS 22.096: "Name identification supplementary services - Stage 1".
[94] 3GPP TS 23.096: "Name identification supplementary services - Stage 2".
[95] 3GPP TS 25.133: "Requirements for support of radio resource management (FDD)".
[96] 3GPP TS 25.123: "Requirements for support of radio resource management (TDD)".
[97] 3GPP TS 36.133: "Evolved Universal Terrestrial Radio Access (E-UTRA); Requirements for
support of radio resource management".
[98] 3GPP TS 31.102: "Characteristics of the Universal Subscriber Identity Module (USIM)
application".
[99] 3GPP TS 23.040: "Technical realization of the Short Message Service (SMS)".
[100] 3GPP TS 23.041: "Technical realization of Cell Broadcast Service (CBS)".
[101] 3GPP TS 24.341: "Support of SMS over IP networks".
[102] 3GPP TS 24.167: "3GPP IMS Management Object (MO); Stage 3".
[103] IETF STD 5: "Internet Protocol".
[104] IETF STD 51: "The Point-to-Point Protocol (PPP)".
[105] RFC 1144: "Compressing TCP/IP Headers for Low-Speed Serial Links".
[106] RFC 2460: "Internet Protocol, Version 6 (IPv6) Specification".
[107] RFC 2507: "IP Header Compression".
[108] RFC 3095: "RObust Header Compression (ROHC): Framework and four profiles: RTP, UDP,
ESP, and uncompressed".
[109] 3GPP TS 24.080: "Mobile radio interface Layer 3 supplementary service specification; Formats
and coding".
[110] 3GPP TS 29.002: "Mobile Application Part (MAP) specification".
[111] RFC 3261: "SIP: Session Initiation Protocol".
[112] RFC 3966: "The tel URI for Telephone Numbers".
[113] RFC 3969: "The Internet Assigned Number Authority (IANA) Uniform Resource Identifier (URI)
Parameter Registryfor the Session Initiation Protocol (SIP)".
[114] RFC 5341: "The Internet Assigned Number Authority (IANA) tel Uniform Resource Identifier
(URI) Parameter Registry".
[115] 3GPP TS 36.355: "Evolved Universal Terrestrial Radio Access (E-UTRA); LTE Positioning
Protocol (LPP)".
[116] RFC 2141: "URN Syntax".
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
15
3GPP TS 27.007 version 13.3.0 Release 13
[117] RFC 3406: "Uniform Resource Names (URN) Namespace Definition Mechanisms".
[118] RFC 5031: "A Uniform Resource Name (URN) for Emergency and Other Well-Known Services".
[119] 3GPP TS 24.607: "Originating Identification Presentation (OIP) and Originating Identification
Restriction (OIR) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol
specification".
[120] 3GPP TS 24.608: "Terminating Identification Presentation (TIP) and Terminating Identification
Restriction (TIR) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol
specification".
[121] 3GPP TS 24.654: "Closed User Group (CUG) using IP Multimedia (IM) Core Network (CN)
subsystem, Protocol Specification".
[122] RFC 4715: "The Integrated Services Digital Network (ISDN) Subaddress Encoding Type for tel
URI".
[123] 3GPP TS 22.093: "Completion of Calls to Busy Subscriber (CCBS); Service description, Stage 1".
[124] 3GPP TS 22.094: "Follow Me service description; Stage 1".
[125] 3GPP TS 22.097: "Multiple Subscriber Profile (MSP) Phase 2; Service description; Stage 1".
[126] 3GPP TS 22.135: "Multicall; Service description; Stage 1".
[127] 3GPP TS 24.182: "IP Multimedia Subsystem (IMS) Customized Alerting Tones (CAT); Protocol
specification".
[128] 3GPP TS 24.183: "IP Multimedia Subsystem (IMS) Customized Ringing Signal (CRS); Protocol
specification".
[129] 3GPP TS 24.239: "Flexible Alerting (FA) using IP Multimedia (IM) Core Network (CN)
subsystem; Protocol specification".
[130] 3GPP TS 24.259: "Personal Network Management (PNM)".
[131] 3GPP TS 24.390: "Unstructured Supplementary Service Data (USSD) using IP Multimedia (IM)
Core Network (CN) subsystem IMS".
[132] 3GPP TS 24.604: "Communication Diversion (CDIV) using IP Multimedia (IM) Core Network
(CN) subsystem; Protocol specification".
[133] 3GPP TS 24.605: "Conference (CONF) using IP Multimedia (IM) Core Network (CN) subsystem;
Protocol specification".
[134] 3GPP TS 24.606: "Message Waiting Indication (MWI) using IP Multimedia (IM) Core Network
(CN) subsystem; Protocol specification".
[135] 3GPP TS 24.610: "Communication HOLD (HOLD) using IP Multimedia (IM) Core Network
(CN) subsystem; Protocol specification".
[136] 3GPP TS 24.611: "Anonymous Communication Rejection (ACR) and Communication Barring
(CB) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol specification".
[137] 3GPP TS 24.615: "Communication Waiting (CW) using IP Multimedia (IM) Core Network (CN)
subsystem; Protocol Specification".
[138] 3GPP TS 24.616: "Malicious Communication Identification (MCID) using IP Multimedia (IM)
Core Network (CN) subsystem; Protocol specification".
[139] 3GPP TS 24.629: "Explicit Communication Transfer (ECT) using IP Multimedia (IM) Core
Network (CN) subsystem; Protocol specification".
[140] 3GPP TS 24.642: "Completion of Communications to Busy Subscriber (CCBS) and Completion of
Communications by No Reply (CCNR) using IP Multimedia (IM) Core Network (CN) subsystem;
Protocol specification".
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
16
3GPP TS 27.007 version 13.3.0 Release 13
[141] 3GPP TS 24.647: "Advice Of Charge (AOC) using IP Multimedia (IM) Core Network (CN)
subsystem".
[142] 3GPP TS 36.509: "Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Packet
Core (EPC); Special conformance testing functions for User Equipment (UE)".
[143] 3GPP TS 25.102: "Multiplexing and channel coding (TDD)".
[144] 3GPP TS 25.212: "Multiplexing and channel coding (FDD)".
[145] 3GPP TS 36.300: "Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Universal
Terrestrial Radio Access Network (E-UTRAN); Overall description".
[146] 3GPP TS 45.001: "Physical layer on the radio path; General description".
[147] 3GPP TS 22.101: "Service aspects; Service principles".
[148] 3GPP TS 24.090: "Unstructured Supplementary Service Data (USSD); Stage 3".
[149] 3GPP TS 23.682: "Architecture Enhancements to facilitate communications with Packet Data
Networks and Applications".
[150] 3GPP TS 36.443: "Evolved Universal Terrestrial Radio Access Network (E-UTRAN); M2
Application Protocol (M2AP)".
[151] Wi-Fi Alliance: "Hotspot 2.0 (Release 2) Technical Specification, version 1.0.0", 2014-08-08.
[152] IEEE Std 802.11™-2012: "Information Technology- Telecommunications and information
exchange between systems-Local and metropolitan area networks-Specific requirements-Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications".
[153] 3GPP TS 24.312: "Access Network Discovery and Selection Function (ANDSF) Management
Object (MO)".
[154] 3GPP TS 36.101: "Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE)
radio transmission and reception".
[155] RFC 4122: "A Universally Unique IDentifier (UUID) URN Namespace".
underline
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
17
3GPP TS 27.007 ve
rsion 13.3.0 Release 13
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following syntactical definitions apply (refer also clause 4):
<CR> Carriage return character, which value is specified with command S3.
<LF> Linefeed character, which value is specified with command S4.
<...> Name enclosed in angle brackets is a syntactical element. Brackets themselves do not appear in the
command line.
[...] Optional subparameter of a command or an optional part of TA information response is enclosed
in square brackets. Brackets themselves do not appear in the command line. When subparameter is
not given in parameter type commands, new value equals to its previous value. In action type
commands, action should be done on the basis of the recommended default setting of the
subparameter.
underline Underlined defined subparameter value is the recommended default setting of this subparameter.
In parameter type commands, this value should be used in factory settings which are configured
by ITU-T Recommendation V.250 [14] command &F0. In action type commands, this value
should be used when subparameter is not given.
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AT ATtention; this two-character abbreviation is always used to start a command line to be sent from
TE to TA
ASCI Advanced Speech Call Items, including VGCS, VBS and eMLPP
BCD Binary Coded Decimal
eMLPP Enhanced Multi-Level Precedence and Pre-emption Service
ETSI European Telecommunications Standards Institute
FTM Frame Tunnelling Mode (refer 3GPP TS 27.001 [41] and 3GPP TS 29.007 [42])
HSCSD High Speed Circuit Switched Data
IMEI International Mobile station Equipment Identity
IRA International Reference Alphabet (ITU-T Recommendation T.50 [13])
IrDA Infrared Data Association
ISO International Standards Organization
ITU-T International Telecommunication Union - Telecommunications Standardization Sector
ME Mobile Equipment
MMTEL Multimedia Telephony
MoU Memorandum of Understanding (GSM operator joint)
MT Mobile Termination
MTU Maximum Transfer Unit
NSLPI NAS Signalling Low Priority Indication
PCCA Portable Computer and Communications Association
PTT Push to Talk
RDI Restricted Digital Information
RLP Radio Link Protocol
SIM Subscriber Identity Module
TA Terminal Adaptor, e.g. a GSM data card (equal to DCE; Data Circuit terminating Equipment)
TE Terminal Equipment, e.g. a computer (equal to DTE; Data Terminal Equipment)
TIA Telecommunications Industry Association
UDI Unrestricted Digital Information
UE User Equipment
UICC Universal Integrated Circuit Card
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
18
3GPP TS 27.007 version 13.3.0 Release 13
USAT USIM Application Toolkit
USIM Universal Subscriber Identity Module
VBS Voice Broadcast Service
VGCS Voice Group Call Service
4 AT command syntax
4.0 General
This clause summarizes general aspects on AT commands and issues related to them.
TE software implementors must take account that future versions of this specification may include additional
parameters beyond what is expected in any response to an AT Set Command, Read Command, Test Command, or
unsolicited result code. Implementations must therefore analyse all parameters provided from the TA and discard
(ignore) any parameters received following the parameters expected by the TE software.
For further information refer ITU-T Recommendation V.250 [14].
In the tables for the commands syntaxes, the possible response(s) are outlined as follows:
- the responses from ITU-T Recommendation V.250 [14] ( like OK and ERROR) are normally not shown; and
- the final response +CME ERROR is shown when a final result code in subclause 9.2 can be provided.
In certain implementations, AT commands are used as an internal interface within the physical handset, e.g. between the
application and the radio interface layer 3 stack implemented on different processors. Certain AT commands transfer
information in the clear that can be regarded as sensitive with regards to security or privacy. Care must be exercised in
AT commands that:
- transfer passwords (e.g. +CLCK, +CPWD or +CPBS);
- transfer identities (e.g. IMSI) or details of a call (e.g. +COLP);
- transfer the current location of the phone (e.g. +CMOLR);
- reveal the IMEI (e.g. +CGSN);
- allow the TE to take unintentionally control over the SIM-MT interface (e.g. +CSIM);
- enable/disable access to commands protected by security mechanism (e.g. +CSCC); or
- exchange security related parameters and keys with the UICC (e.g. +CEAP and +CERP).
The above mentioned AT commands and parameters are examples to illustrate the concerns and is not meant to be a
comprehensive list.
4.1 Command line
See figure 2 for general structure of a command line. Standardized basic commands are found only in
ITU-T Recommendation V.250 [14]. GSM/UMTS commands use syntax rules of extended commands. Every extended
command has a test command (trailing =?) to test the existence of the command and to give information about the type
of its subparameters. Parameter type commands also have a read command (trailing ?) to check the current values of
subparameters. Action type commands do not store the values of any of their possible subparameters, and therefore do
not have a read command.
L CMD +CM
ETSI
ETSI TS
127 007 V13.3.0 (2016
-
03)
19
3GPP TS 27.007 version 13.3.0 Release 13
ATCMD1 CMD2=12; +CMD1; +CMD2=,,15; +CMD2?; +CMD2=?<CR>
command line prefix
basic command
(no + prefix)
subparameter
extended command
(prefixed with +)
extended commands are
delimited with semicolon
subparameters
may be omitted
command line
termination character
read command for checking
current subparameter values
test command for checking
possible subparameter values
Figure 2: Basic structure of a command line
If verbose responses are enabled with command V1 and all commands in a command line has been performed
successfully, result code <CR><LF>OK<CR><LF> is sent from the TA to the TE. If numeric responses are enabled
with command V0, result code 0<CR> is sent instead.
If verbose responses are enabled with command V1 and subparameter values of a command are not accepted by the TA
(or command itself is invalid, or command cannot be performed for some reason), result code
<CR><LF>ERROR<CR><LF> is sent to the TE and no subsequent commands in the command line are processed. If
numeric responses are enabled with command V0, result code 4<CR> is sent instead. ERROR (or 4) response may be
replaced by +CME ERROR: <err> (refer clause 9) when command was not processed due to an error related to MT
operation.
4.2 Information responses and result codes
The TA response for the example command line of figure 2 could be as shown in figure 3. Here, verbose response
format is enabled with command V1. If numeric format V0 would have been used, <CR><LF> headers of information
responses would have been left out and final result code changed to 0<CR>.
<CR><LF>+CMD2: 3,0,15,"GSM"<CR><LF>
<CR><LF>+CMD2: (0-3),(0,1),(0-12,15),("GSM","IRA")<CR><LF>
<CR><LF>OK<CR><LF>
information response to +CMD2?
information response to +CMD2=?
final result code
also string type subparameters possible
shows acceptable ranges of each subparameter
Figure 3: Response to a command line
So called intermediate result codes inform about progress of TA operation (e.g. connection establishment CONNECT),
and so called unsolicited result codes indicate occurrence of an event not directly associated with issuance of a
command from TE (e.g. ring indication RING).
4.3 ITU-T Recommendation V.250 [14] TE-TA interface
commands
Table 1 summarizes ITU-T Recommendation V.250 [14] commands relating to command line and response formatting,
and TA-TE interface operation. All are applicable to GSM/UMTS terminals.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
20
3GPP TS 27.007 version 13.3.0 Release 13
Table 1: V.250 commands relating to TE-TA interface
Command
Subclause
Impl.
Use in GSM/UMTS
S3=[<value>] 6.2.1 mand. command line termination character (mandatory default setting IRA 13)
S4=[<value>] 6.2.2 mand. response formatting character (recommended default IRA 10)
S5=[<value>] 6.2.3 mand. command line editing character (recommended default IRA 8)
E[<value>] 6.2.4 mand.
command echo (recommended default 1 i.e. TA echoes commands
back)
Q[<value>] 6.2.5 mand.
result code suppression (recommended default 0 i.e. TA transmits result
codes)
V[<value>] 6.2.6 mand. TA response format (recommended default 1 i.e. verbose format)
X[<value>] 6.2.7 mand.
defines CONNECT result code format; values manufacturer specific
&C[<value>] 6.2.8 mand.
determines how ITU-T V.24 circuit 109 (or equivalent) relates to the
detection of received line signal from remote end (recommended default
1 i.e. 109 operation relates to detection of received signal)
&D[<value>] 6.2.9 mand.
determines how TA responds when ITU-T V.24 circuit 108/2 (or
equivalent) is changed from ON to OFF condition during online data
state
+IPR=[<value>] 6.2.10 opt. fixed TE data rate (recommended default 0 i.e. automatic detection)
+ICF=[<format>[
,<parity>]] 6.2.11 opt.
TE-TA character framing (recommended default 3,3 i.e. eight data bits,
no parity, 1 stop bit)
+IFC=[<by_te> [
,<by_ta>]] 6.2.12 opt.
TE-TA local flow control (recommended default 2,2 i.e. TE uses ITU-T
V.24 circuit 133 (or equivalent), and TA circuit 106 (or equivalent))
+ILRR=[<value>] 6.2.13 opt.
determines whether the used local TE-TA data rate is informed using
intermediate result code +ILRR: <rate> before going online data
state after call answering or originating
5 General commands
5.0 General
ITU-T Recommendation V.250 [14] includes "Generic DCE Control" commands with the prefix +G. These commands
are for the identification of the TA. Four of those commands are adapted here to be the identification commands of the
MT. Syntax is otherwise similar but the prefix is +CG. TIA IS-99 [15] uses same commands for base station
identification.
5.1 Request manufacturer identification +CGMI
Table 2: +CGMI action command syntax
Command
Possible response(s)
+CGMI
<manufacturer>
+CME ERROR: <err>
+CGMI=?
Description
Execution command causes the TA to return one or more lines of information text <manufacturer>, determined by
the MT manufacturer, which is intended to permit the user of the TA to identify the manufacturer of the MT to which it
is connected to. Typically, the text will consist of a single line containing the name of the manufacturer, but
manufacturers may choose to provide more information if desired. Refer subclause 9.2 for possible <err> values.
Defined values
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
21
3GPP TS 27.007 version 13.3.0 Release 13
<manufacturer>: the total number of characters, including line terminators, in the information text shall not
exceed 2048 characters.
Text shall not contain the sequence 0<CR> or OK<CR>
Implementation
Optional.
5.2 Request model identification +CGMM
Table 3: +CGMM action command syntax
Command
Possible response(s)
+CGMM <model>
+CME ERROR: <err>
+CGMM=?
Description
Execution command causes the TA to return one or more lines of information text <model>, determined by the MT
manufacturer, which is intended to permit the user of the TA to identify the specific model of the MT to which it is
connected to. Typically, the text will consist of a single line containing the name of the product, but manufacturers may
choose to provide more information if desired. Refer subclause 9.2 for possible <err> values.
Defined values
<model>: the total number of characters, including line terminators, in the information text shall not exceed 2048
characters.
Text shall not contain the sequence 0<CR> or OK<CR>
Implementation
Optional.
5.3 Request revision identification +CGMR
Table 4: +CGMR action command syntax
Command
Possible response(s)
+CGMR <revision>
+CME ERROR: <err>
+CGMR=?
Description
Execution command causes the TA to return one or more lines of information text <revision>, determined by the
MT manufacturer, which is intended to permit the user of the TA to identify the version, revision level or date, or other
pertinent information of the MT to which it is connected to. Typically, the text will consist of a single line containing
the version of the product, but manufacturers may choose to provide more information if desired. Refer subclause 9.2
for possible <err> values.
Defined values
<revision>: the total number of characters, including line terminators, in the information text shall not exceed
2048 characters.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
22
3GPP TS 27.007 version 13.3.0 Relea
se 13
Text shall not contain the sequence 0<CR> or OK<CR>
Implementation
Optional.
5.4 Request product serial number identification +CGSN
Table 5: +CGSN action command syntax
Command
Possible response(s)
+CGSN[=<snt>] when <snt>=0 (or omitted) and command successful:
<sn>
when <snt>=1 and command successful:
+CGSN: <imei>
when <snt>=2 and command successful:
+CGSN: <imeisv>
when <snt>=3 and command successful:
+CGSN: <svn>
+CME ERROR: <err>
+CGSN=? when TE supports <snt> and command successful:
+CGSN: (list of supported <snt>s)
Description
Execution command causes the TA to return IMEI (International Mobile station Equipment Identity number) and
related information to identify the MT that the TE is connected to.
Refer subclause 9.2 for possible <err> values.
Test command returns values supported as a compound value. For a TA which does not support <snt>, only OK is
returned.
Defined values
<snt>: integer type indicating the serial number type that has been requested.
0 returns <sn>
1 returns the IMEI (International Mobile station Equipment Identity)
2 returns the IMEISV (International Mobile station Equipment Identity and Software Version number)
3 returns the SVN (Software Version Number)
<sn>: one or more lines of information text determined by the MT manufacturer. Typically, the text will consist of
a single line containing the IMEI number of the MT, but manufacturers may choose to provide more information
if desired. The total number of characters, including line terminators, in the information text shall not exceed
2048 characters. Text shall not contain the sequence 0<CR> or OK<CR>
<imei>: string type in decimal format indicating the IMEI; refer 3GPP TS 23.003 [7], subclause 6.2.1. IMEI is
composed of Type Allocation Code (TAC) (8 digits), Serial Number (SNR) (6 digits) and the Check Digit (CD)
(1 digit). Character set used in <imei> is as specified by command Select TE Character Set +CSCS.
<imeisv>: string type in decimal format indicating the IMEISV; refer 3GPP TS 23.003 [7], subclause 6.2.2. The
16 digits of IMEISV are composed of Type Allocation Code (TAC) (8 digits), Serial Number (SNR) (6 digits)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
23
3GPP TS 27.007 version 13.3.0 Release 13
and the software version (SVN) (2 digits). Character set used in <imeisv> is as specified by command Select
TE Character Set +CSCS.
<svn>: string type in decimal format indicating the current SVN which is a part of IMEISV; refer
3GPP TS 23.003 [7], subclause 6.2.2. This allows identifying different software versions of a given mobile.
Character set used in <svn> is as specified by command Select TE Character Set +CSCS.
NOTE: The default value <snt>=0 returns the information text <sn> with no command name prefixed. This
has been done to retain backward compatibility. All other values of <snt> return the information text
including command name prefix.
Informative examples
To get <sn> which returns IMEI of the MT
AT+CGSN
490154203237518
OK
To get <imei> which returns IMEI of the MT
AT+CGSN=1
+CGSN: "490154203237518"
OK
Implementation
Optional.
5.5 Select TE character set +CSCS
Table 6: +CSCS parameter command syntax
Command
Possible response(s)
+CSCS=[<chset>]
+CSCS? +CSCS: <chset>
+CSCS=? +CSCS: (list of supported <chset>s)
Description
Set command informs TA which character set <chset> is used by the TE. TA is then able to convert character strings
correctly between TE and MT character sets.
When TA-TE interface is set to 8-bit operation and used TE alphabet is 7-bit, the highest bit shall be set to zero.
NOTE: It is manufacturer specific how the internal alphabet of MT is converted to/from the TE alphabet.
Read command shows current setting and test command displays conversion schemes implemented in the TA.
Test command returns values supported as a compound value.
Defined values
<chset>: character set as a string type (conversion schemes not listed here can be defined by manufacturers)
"GSM" GSM 7 bit default alphabet (3GPP TS 23.038 [25]); this setting causes easily software flow control
(XON/XOFF) problems.
"HEX" Character strings consist only of hexadecimal numbers from 00 to FF; e.g. "032FE6" equals three
8-bit characters with decimal values 3, 47 and 230; no conversions to the original MT character set
shall be done.
If MT is using GSM 7 bit default alphabet, its characters shall be padded with 8th bit (zero) before converting them to
hexadecimal numbers (i.e. no SMS-style packing of 7-bit alphabet).
ETSI
ETSI TS 127 007 V13.3.0 (2
016
-
03)
24
3GPP TS 27.007 version 13.3.0 Release 13
"IRA" International reference alphabet (see ITU-T Recommendation T.50 [13]).
"PCCPxxx" PC character set Code Page xxx
"PCDN" PC Danish/Norwegian character set
"UCS2" 16-bit universal multiple-octet coded character set (see ISO/IEC10646 [32]); UCS2 character
strings are converted to hexadecimal numbers from 0000 to FFFF; e.g. "004100620063" equals
three 16-bit characters with decimal values 65, 98 and 99.
"UTF-8" Octet (8-bit) lossless encoding of UCS characters (see RFC 3629 [69]); UTF-8 encodes each UCS
character as a variable number of octets, where the number of octets depends on the integer value
assigned to the UCS character. The input format shall be a stream of octets. It shall not be
converted to hexadecimal numbers as in "HEX" or "UCS2". This character set requires an 8-bit
TA – TE interface.
"8859-n" ISO 8859 Latin n (1-6) character set
"8859-C" ISO 8859 Latin/Cyrillic character set
"8859-A" ISO 8859 Latin/Arabic character set
"8859-G" ISO 8859 Latin/Greek character set
"8859-H" ISO 8859 Latin/Hebrew character set
Implementation
Mandatory when a command using the setting of this command is implemented.
5.6 Request international mobile subscriber identity +CIMI
Table 7: +CIMI action command syntax
Command
Possible response(s)
+CIMI
<IMSI>
+CME ERROR: <err>
+CIMI=?
Description
Execution command causes the TA to return <IMSI>, which is intended to permit the TE to identify the individual
SIM card or active application in the UICC (GSM or USIM) which is attached to MT. Refer subclause 9.2 for possible
<err> values.
Defined values
<IMSI>: International Mobile Subscriber Identity (string without double quotes)
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
25
3GPP TS 27.007 version 13.3.0 Release 13
5.7 Multiplexing mode +CMUX
Table 8: +CMUX parameter command syntax
Command
Possible response(s)
+CMUX=<transparency>[,<su
bset>[,<port_speed>[,<N1>
[,<T1>[,<N2>[,<T2>[,<T3>[
,<k>]]]]]]]]
+CME ERROR: <err>
+CMUX?
+CMUX: <transparency>,[<subset>],<port_speed>
,<N1>,<T1>,<N2>,<T2>,<T3>[,<k>]
+CME ERROR: <err>
+CMUX=?
+CMUX: (list of supported <transparency>s),(list of
supported <subset>s),(list of supported
<port_speed>s),(list of supported <N1>s),(list of supported
<T1>s),(list of supported <N2>s),(list of supported
<T2>s),(list of supported <T3>s),(list of supported <k>s)
Description
This command is used to enable/disable the 3GPP TS 27.010 [45] multiplexing protocol control channel. Refer
subclause 9.2 for possible <err> values. The AT command sets parameters for the Control Channel. If the parameters
are left out, the default value is used.
Read command returns the current settings.
Test command returns the supported parameters as compound values.
It is recommended that the MT/TA/TE should autobaud to the +CMUX command up to and including an interface speed
of 9600 bits/s.
The OK or +CME ERROR: <err> response is returned at the speed of the +CMUX command prior to entering
<transparency>.
It is recommended that whenever the multiplexer control channel is released the MT/TA/TE should assume an interface
rate of up to and including 9600 bits/s for auto bauding purposes irrespective of any previous higher speed having been
selected.
If a +CMUX command is issued whilst in any multiplexer mode then that +CMUX command shall be ignored and the
MT/TA shall return a +CME ERROR: <err> response.
Defined values
<transparency>: integer type (multiplexer Transparency Mechanism)
0 Basic option
1 Advanced option
<subset>: integer type. This parameter defines the way in which the multiplexer control channel is set up. A
virtual channel may subsequently be set up differently but in the absence of any negotiation for the settings of a
virtual channel, the virtual channel shall be set up according to the control channel <subset> setting.
0 UIH frames used only
1 UI frames used only
2 I frames used only
<port_speed> integer type (transmission rate). The default value is implementation specific.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
26
3GPP TS 27.007 version 13.3.0 Release 13
1 9 600 bit/s
2 19 200 bit/s
3 38 400 bit/s
4 57 600 bit/s
5 115 200 bit/s
6 230 400 bits/s
<N1>: integer type (maximum frame size)
1- 32768, where the 31 is default for Basic option and 64 is default for Advanced option (see
<transparency>)
<T1>: integer type (acknowledgement timer in units of ten milliseconds)
1-255, where 10 is default (100 ms)
<N2>: integer type (maximum number of re-transmissions)
0-100, where 3 is default
<T2>: integer type (response timer for the multiplexer control channel in units of ten milliseconds)
2-255, where 30 is default (300 ms)
NOTE: T2 must be longer than T1.
<T3>: integer type (wake up response timer in seconds)
1-255, where 10 is default
<k>: integer type (window size, for Advanced option with Error-Recovery Mode)
1-7, where 2 is default
Implementation
Mandatory, if 3GPP TS 27.010 [45] supported in the MT/TA.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
27
3GPP TS 27.007 version 13.3.0 Release 13
5.8 ITU-T Recommendaton V.250 [14] generic TA control
commands
Table 9: V.250 generic TA control commands
Command
Subclause
Impl.
Use in GSM/UMTS
Z[<value>] 6.1.1 mand.
TA sets all parameters to their defaults as specified by a user
memory profile or by the manufacturer, and resets TA
&F[<value>] 6.1.2 mand.
TA sets all parameters to their defaults as specified by the
manufacturer
I[<value>] 6.1.3 opt.
request manufacturer specific information about the TA (software
cannot use this command to determine the capabilities of a TA)
+GMI 6.1.4 mand.
request TA manufacturer identification (may equal to +CGMI)
+GMM 6.1.5 mand.
request TA model identification (may equal to +CGMM)
+GMR 6.1.6 mand.
request TA revision identification (may equal to +CGMR)
+GSN 6.1.7 opt.
request TA serial number identification (may equal to +CGSN)
+GOI 6.1.8 opt.
request ISO system global object
identification of the TA (general
format defined in ITU-T Recommendation X.208; encoding rules
in ITU-T Recommendation X.209)
+GCAP 6.1.9 mand.
request overall capabilities of TA; the response code for a TA
building on this document shall be +CGSM
+GCI=<T.35> 6.1.10 opt. selects the country of installation for the TA using ITU-T
Recommendation T.35 Annex A country codes
5.9 PCCA STD-101 [17] select wireless network +WS46
PCCA STD-101 [17] includes a command to select the cellular network (Wireless Data Service; WDS) to operate with
the TA. PCCA calls this WDS-Side Stack Selection. This command may be used when TA is asked to indicate the
networks in which it can operate.
Table 10: +WS46 parameter command syntax
Command
Possible response(s)
+WS46=[<n>]
+WS46? <n>
+WS46=? (list of supported <n>s)
Description
Set command selects the WDS side stack <n> to be used by the TA. Read command shows current setting and test
command displays side stacks implemented in the TA.
Read command (query) returns the current value of <n>.
Test command returns values supported as a compound value.
Defined values for Query
<n>: integer type
12 GSM Digital Cellular Systems (GERAN only)
22 UTRAN only
25 3GPP Systems (GERAN, UTRAN and E-UTRAN)
28 E-UTRAN only
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
28
3GPP TS 27.007 version 13.3.0 Release 13
29 GERAN and UTRAN
30 GERAN and E-UTRAN
31 UTRAN and E-UTRAN
The values in <n> for Query are mutually exclusive. If one value (e.g. "25") is returned, other values shall not be
returned.
Defined values for Set
<n>: integer type
12 3GPP System
22 Not used. If received, the value shall be treated as if 12 had been received or an ERROR shall be returned.
25 Not used. If received, the value shall be treated as if 12 had been received or an ERROR shall be returned.
28 Not used. If received, the value shall be treated as if 12 had been received or an ERROR shall be returned.
29 Not used. If received, the value shall be treated as if 12 had been received or an ERROR shall be returned.
30 Not used. If received, the value shall be treated as if 12 had been received or an ERROR shall be returned.
31 Not used. If received, the value shall be treated as if 12 had been received or an ERROR shall be returned.
refer PCCA STD-101 [17] for other values.
Implementation
Mandatory in PCCA STD-101 [17], but optional for GSM/UMTS/EPS.
5.10 Informative examples
When beginning to build a communication link, a general TE application controlling a TA needs to determine the TA
and the MT to which it is connected. ITU-T Recommendation V.250 [14] has seven commands for TA identification
from which four are mandatory to be implemented in a TA. An example of this command sequence requesting
manufacturer (+GMI), model (+GMM), revision (+GMR) and serial number (+GSN) information would be:
AT+GMI
Manufacturer ABC
OK
AT+GMM
GSM Ultimate Data Device
OK
AT+GMR
1.00
OK
AT+GSN
987612345-123
OK
The maximum lengths of the information responses are defined to be 2048 characters, but it is recommended that they
are kept as simple as in the example. The serial number command is defined as optional. Another optional command is
Global Object Identification command (+GOI) which should return the object identifiers of
ITU-T Recommendation X.208 as numeric strings delimited by periods. The Complete Capabilities List command
(+GCAP) should indicate the major capability areas of the TA. The support of different areas is presented in the
response of +GCAP command. Each area may be presented by the selection command name of a specific capability area
(e.g. +FCLASS for fax support) or some other predefined response. For instance, a GSM TA with fax capabilities could
respond as follows:
AT+GCAP
+GCAP: +CGSM,+FCLASS,+W
OK
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
29
3GPP TS 2
7.007 version 13.3.0 Release 13
The first supported area in the response is presented with +CGSM. It is the response text to show that some or all GSM
commands of the present document are supported. Second response text (+FCLASS) informs that some fax or voice
capabilities are present, and the third text (+W) about the presence of wireless commands as specified by
PCCA STD-101 [17]. Command +FCLASS=? (refer e.g. ITU-T Recommendation T.31 [11] and
ITU-T Recommendation T.32 [12]) should be used to query the supported fax capabilities and +WS46=? to query the
wireless data services available:
AT+FCLASS=?;+WS46=?
0,1,2,2.0
(12)
OK
The TA of this example supports GSM data services, and fax service class 1 (TIA-578-A), 2 (manufacturer specific)
and 2.0 (ITU-T Recommendation T.32 [12] / TIA-592).
The present document defines commands for MT identification which are similar to those for TA identification in
ITU-T Recommendation V.250 [14], for an example:
AT+CGMI
Mobile Manufacturer XYZ
OK
AT+CGMM
GSM Phone 1234
OK
AT+CGMR
1.00
OK
AT+CGSN
123456121234561
OK
Manufacturer, model and version commands work similarly as for TA, except that the serial number query returns the
International Mobile Station Equipment Identity (IMEI) number. IMEI is fifteen digits long and consists of a type
approval code, a final assembly code, a serial number and a spare digit (refer 3GPP TS 23.003 [7]). When the TA is
implemented inside MT, the responses for both TA and MT queries will most likely follow the responses of MT
identification.
6 Call control commands and methods
6.0 General
This clause describes the control of calls. Normal data and fax call control is done as in
ITU-T Recommendation V.250 [14], ITU-T Recommendation T.31 [11] and ITU-T Recommendation T.32 [12]. For
voice call originating, refer subclause "ITU-T Recommendation V.250 dial command D" and clause "Commands for
enhanced support of dialling".
6.1 Select type of address +CSTA
Table 11: +CSTA parameter command syntax
Command
Possible response(s)
+CSTA=[<type>]
+CSTA? +CSTA: <type>
+CSTA=? +CSTA: (list of supported <type>s)
Description
Set command selects the type of number for further dialling commands (D) according to GSM/UMTS specifications.
Read command returns the current value of <type>.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
30
3GPP TS 27.007 version 13.3.0 Release 13
Test command returns values supported as a compound value.
Defined values
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7); default 145 when
dialling string includes international access code character "+", otherwise 129
Implementation
Mandatory when other than default value allowed.
6.2 ITU-T Recommendation V.250 [14] dial command D
ITU-T Recommendation V.250 [14] dial command D lists characters that may be used in a dialling string for making a
call or controlling supplementary services in accordance with 3GPP TS 22.030 [19]. Their use in GSM/UMTS is listed
in this subclause, as well as new dial modifiers applicable only to GSM/UMTS are introduced. For a MT supporting AT
commands only, it is mandatory to support the control of supplementary services in accordance with
3GPP TS 22.030 [19] through the dial command or through the specific supplementary service commands (+CCFC,
+CLCK, etc.), where 3GPP TS 22.030 [19] identifies the supplementary services as mandatory.
V.250 dialling digits
1 2 3 4 5 6 7 8 9 0 * # + A B C (implementation of these characters is mandatory for GSM/UMTS)
D (implementation of this character is optional for GSM/UMTS, and it is ignored)
V.250 modifier characters
, (implementation of this character is mandatory for GSM/UMTS, but it may be ignored)
T P (implementation of these characters is mandatory for GSM/UMTS, but they are ignored)
! W @ (implementation of these characters is optional for GSM/UMTS, and they are ignored)
V.250 semicolon character
In GSM/UMTS, when semicolon character is given after dialling digits (or modifiers), a voice call originated to the
given address. TA returns to command state immediately (or after possible +COLP result code; refer subclause
"Connected line identification presentation +COLP"). Refer Annex G for a detailed example.
GSM/UMTS modifier characters
> (refer subclause "Direct dialling from phonebooks")
I or i (override the CLIR supplementary service subscription default value for this call; I = invocation (restrict CLI
presentation) and i = suppression (allow CLI presentation); refer subclause "Calling line identification restriction
+CLIR")
G or g (control the CUG supplementary service information for this call; uses index and info values set with command
+CCUG or +CECUG; refer subclause "Closed user group +CCUG" and subclause "Enhanced closed user group
+CECUG")
6.3 Direct dialling from phonebooks
GSM/UMTS MT and SIM/UICC can contain phonebooks which have a phone number and an alphanumeric field for
each phonebook entry location. The use of ITU-T Recommendation V.250 [14] dialling command ensures that direct
dialling from MT and SIM/UICC phonebook is possible through ordinary communications software which just gives
the phone number field to be filled and then use the D command to originate the call. Available memories may be
queried with Select Phonebook Storage test command +CPBS=?, and location range for example with Read Phonebook
Entries test command +CPBR=?.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
31
3GPP TS 27.007 version 13.3.0 Release 13
Execute commands
1. D><str>[I][G][;] originate call to phone number which corresponding alphanumeric field is <str> (if
possible, all available memories should be searched for the correct entry).
2. D>mem<n>[I][G][;] originate call to phone number in memory mem entry location <n> (available memories
may be queried with Select Phonebook Storage test command +CPBS=?; mem could be
e.g. ME).
3. D><n>[I][G][;] originate call to phone number in entry location <n> (it is manufacturer specific which
memory storage of MT, SIM/UICC in the currently selected card slot and TA is used;
command Select Phonebook Memory Storage +CPBS setting is recommended to be
used).
Semicolon character shall be added when voice call is originated. CLIR and CUG per call base modifiers may also be
present.
Responses
Possible error responses include +CME ERROR: <err> when error is related to MT functionality. Refer
subclause 9.2 for possible <err> values. Otherwise TA responses can have values defined by
ITU-T Recommendation V.250 [14] and commands Service Reporting Control +CR and Connected Line Identification
Presentation +COLP. Detailed error report of an unsuccessful originated call failed in a GSM/UMTS network error can
be obtained with command Extended Error Report +CEER (if implemented).
Defined values
<str>: string type value, which should equal to an alphanumeric field in at least one phonebook entry in the
searched memories; used character set should be the one selected with Select TE Character Set +CSCS
<n>: integer type memory location should be in the range of locations available in the memory used
Implementation
Mandatory when direct dialling is implemented. Also phonebook commands implementation is required.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
32
3GPP TS 27.007 version 13.3.0 Release 13
6.4 Call mode +CMOD
Table 12: +CMOD parameter command syntax
Command
Possible response(s)
+CMOD=[<mode>]
+CMOD? +CMOD: <mode>
+CMOD=? +CMOD: (list of supported <mode>s)
Description
Set command selects the call mode of further dialling commands (D) or for next answering command (A). Mode can be
either single or alternating (in the present document, terms "alternating mode" and "alternating call" refer to all
GSM/UMTS bearer and teleservices that incorporate more than one basic service (voice, data, fax) within one call).
When single mode is selected the call originating and hangup procedures are similar to procedures specified in ITU-T
Recommendations V.250 [14], T.31 [11] and T.32 [12]. In GSM/UMTS there can be voice followed by data (refer
3GPP TS 22.002 [1]), alternating voice/data (refer 3GPP TS 22.002 [1]) and alternating voice/fax calls (refer
3GPP TS 22.003 [2]). Refer next two subclauses for alternating call control methods.
Read command returns the current value of <mode>.
Test command returns values supported as a compound value.
NOTE: +CMOD shall be set to zero after a successfully completed alternating mode call. It shall be set to zero also
after a failed answering. The power-up, factory (&F) and user resets (Z) shall also set the value to zero.
This reduces the possibility that alternating mode calls are originated or answered accidentally.
Defined values
<mode>: integer type
0 single mode
1 alternating voice/fax (teleservice 61)
2 alternating voice/data (bearer service 61)
3 voice followed by data (bearer service 81)
all other values below 128 are reserved by the present document
Implementation
Mandatory when alternating mode calls are implemented in the TA.
6.4A Voice call mode +CVMOD
Table 13: +CVMOD parameter command syntax
Command
Possible response(s)
+CVMOD=[<voice_mode>]
+CVMOD? +CVMOD: <voice_mode>
+CVMOD=? +CVMOD: (list of supported <voice_mode>s)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
33
3GPP TS 27.007 version 13.3.0 Release 13
Description
Set command selects the voice call mode for making a Mobile Originated voice call from the UE. The voice call mode
can be CS_ONLY, VOIP_ONLY, CS_PREFERRED or VOIP_PREFERRED. Type of VoIP session preferred (e.g. SIP
VoIP, IMS VoIP) is manufacturer specific issue.
NOTE 1: If the Call Mode is set to CS_ONLY, then the ATD command will make a call in CS mode.
If the Call Mode is set to VOIP_ONLY, then the ATD command will make a call in VoIP mode.
If the Call Mode is set to CS_PREFERRED, then the ATD command gives preference for CS based voice
call.
If the Call Mode is set to VOIP_PREFERRED, then the ATD command gives preference for VoIP based
voice call
NOTE 2: The preferences are not applicable for the emergency call.
NOTE 3: The preferences are not applicable if operator has set preferences for UE originated calls/sessions,
3GPP TS 24.216 [75] subclause 5.6.
Read command returns the current value of <voice_mode>.
Test command returns the values supported by the UE as a compound value.
Defined values
<voice_mode>: integer type. The default value is manufacturer specific.
0 CS_ONLY
1 VOIP_ONLY
2 CS_PREFERRED
3 VOIP_PREFERRED
Implementation
Optional.
6.5 Hangup call +CHUP
Table 13a: +CHUP action command syntax
Command
Possible response(s)
+CHUP
+CHUP=?
Description
Execution command causes the TA to hangup the current GSM/UMTS call of the MT.
NOTE: The purpose of this command is not to replace the ITU-T Recommendation V.250 [14] command H, but
to give an assured procedure to terminate an alternating mode call. Refer next subclause.
Implementation
Mandatory when alternating mode calls implemented in the TA.
AT+FCLASS AT+CM9 / ,/’ ATDxxx /, /, LL ATD or remote milwated ’ \ AT+CHUP or remote mitiared hangup , (or ATH \_ ,/ or dvop DTR) \ ,/ A K
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
34
3GPP TS 27.007 version 13.3
.0 Release 13
6.6 Alternating mode call control method
This subclause describes the procedure to handle alternating mode calls with AT commands. Procedures are mandatory
when alternating mode calls are implemented in the TA.
NOTE 1: ATH and drop DTR will not necessarily cause a hangup from voice mode. If the +CVHU
is implemented
the behaviour shall be controlled by its setting.
Voice followed by data call (bearer service 81)
Figure 4 shows commands to start the call, to switch from voice to data (In-Call Modification) and to hang up the call.
+CMOD and +FCLASS commands indicate the current settings before dialling or answering command, not that they
shall be given just before D or A command. Refer subclause "Cellular result codes +CRC" for possible +CRING result
code values. Refer Annex F for a detailed example.
VOICE DATA
HANGUP
AT+CHUP or
remote initiated hangup
(or ATH
or drop DTR)
ATD or ATA or
remote initiated
ATDxxx;
AT+CMOD=3
AT+FCLASS=0
TA sets +CMOD=0
+CRING: VOICE/XXX
AT+CMOD=3;+FCLASS=0
MT
MO
ATH or
drop DTR or
AT+CHUP or
remote initiated hangup
ATA
Figure 4: Voice followed by data call
Voice/ data call (bearer service number 61)
Figure 5 shows the commands to start the call, to switch between modes (In-Call Modification) and to hang up the call.
+CMOD and +FCLASS commands indicate the current settings before dialling or answering command, not that they
shall be given just before D or A command. Refer subclause "Cellular result codes +CRC" for possible +CRING result
code values. Refer Annex E for a detailed example.
AT+FCLASS:0 *ATDxxx ATD or ATA m V ’ remote initiated , <— ath="" or="" dvcp="" dtr="" or="" remote="" imtialed="" '="" l\="" at+chup‘q¥_="" ,="" mmaleq="" ljangup="" angthfjp="" o‘r="" dtr)="" \1="" ye/mc="" a="" ma="" e="" \="" at+="" fclas="" atd="">
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
35
3GPP TS 27.007 version 13.3.0 Release 13
VOICE DATA
HANGUP
AT+CHUP or
remote initiated hangup
AT+CHUP or
remote initiated hangup
(or ATH
or drop DTR)
ATD or ATA or
remote initiated
ATH or drop DTR or
remote initiated
ATDxxxATDxxx;
AT+CMOD=2
AT+FCLASS=0
TA sets +CMOD=0
+CRING: ALT VOICE/XXX
AT+CMOD=2;+FCLASS=0 +CRING: ALT XXX/VOICE
AT+CMOD=2;+FCLASS=0
MT voice first MT data first
MO
ATA ATA
Figure 5: Alternating voice and data call
Voice/ fax call (teleservice number 61)
Figure 6 shows the commands to start the call, to switch between modes (In-Call Modification) and to hang up the call.
+CMOD and +FCLASS commands indicate the current settings before dialling or answering command, not that they
shall be given just before D or A command. The parameter "x" of +FCLASS command can be 1, 1.0, 2 or 2.0.
NOTE 2: The transition from fax mode to voice mode is for further study.
VOICE FAX
HANGUP
ATD or
remote initiated
ATDxxxATDxxx;
AT+CMOD=1
AT+FCLASS=x
TA sets +CMOD=0
+CRING: ALT VOICE/FAX
AT+CMOD=1;+FCLASS=x +CRING: ALT FAX/VOICE
AT+CMOD=1;+FCLASS=x
MT voice first MT fax first
MO
ATA ATA
refer ITU-T T.31 [11] and T.32 [12]
for different hangup possibilities
(also AT+CHUP shall hangup)
AT+CHUP or
remote initiated hangup
(or ATH
or drop DTR)
Figure 6: Alternating voice and fax call
6.7 Select bearer service type +CBST
Table 14: +CBST parameter command syntax
Command
Possible response(s)
+CBST=[<speed>[,<name>[,<ce>]]]
+CBST? +CBST: <speed>,<name>,<ce>
ETSI
ETSI TS 127 007 V1
3.3.0 (2016
-
03)
36
3GPP TS 27.007 version 13.3.0 Release 13
+CBST=? +CBST: (list of supported <speed>s),(list of
supported <name>s),(list of supported <ce>s)
Description
Set command selects the bearer service <name> with data rate <speed>, and the connection element <ce> to be used
when data calls are originated (refer 3GPP TS 22.002 [1]). Values may also be used during mobile terminated data call
setup, especially in case of single numbering scheme calls (refer +CSNS).
Read command returns the current parameter values.
Test command returns values supported as compound values.
Defined values
NOTE: The default values of the subparameters are manufacturer specific since they depend on the purpose of the
device and data services provided by it. Not all combinations of these subparameters are supported by
GSM/UMTS (refer 3GPP TS 22.002 [1]).
<speed>: integer type
0 autobauding (automatic selection of the speed; this setting is possible in case of 3.1 kHz modem and non-
transparent service)
1 300 bps (V.21)
2 1200 bps (V.22)
3 1200/75 bps (V.23)
4 2400 bps (V.22bis)
5 2400 bps (V.26ter)
6 4800 bps (V.32)
7 9600 bps (V.32)
12 9600 bps (V.34)
14 14400 bps (V.34)
15 19200 bps (V.34)
16 28800 bps (V.34)
17 33600 bps (V.34)
34 1200 bps (V.120)
36 2400 bps (V.120)
38 4800 bps (V.120)
39 9600 bps (V.120)
43 14400 bps (V.120)
47 19200 bps (V.120)
48 28800 bps (V.120)
49 38400 bps (V.120)
50 48000 bps (V.120)
51 56000 bps (V.120)
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
37
3GPP TS 27.007 version 13.3.0 Release 13
65 300 bps (V.110)
66 1200 bps (V.110)
68 2400 bps (V.110 or X.31 flag stuffing)
70 4800 bps (V.110 or X.31 flag stuffing)
71 9600 bps (V.110 or X.31 flag stuffing)
75 14400 bps (V.110 or X.31 flag stuffing)
79 19200 bps (V.110 or X.31 flag stuffing)
80 28800 bps (V.110 or X.31 flag stuffing)
81 38400 bps (V.110 or X.31 flag stuffing)
82 48000 bps (V.110 or X.31 flag stuffing)
83 56000 bps (V.110 or X.31 flag stuffing; this setting can be used in conjunction with asynchronous non-
transparent UDI or RDI service in order to get FTM)
84 64000 bps (X.31 flag stuffing; this setting can be used in conjunction with asynchronous non-transparent
UDI service in order to get FTM)
115 56000 bps (bit transparent)
116 64000 bps (bit transparent)
120 32000 bps (PIAFS32k)
121 64000 bps (PIAFS64k)
130 28800 bps (multimedia)
131 32000 bps (multimedia)
132 33600 bps (multimedia)
133 56000 bps (multimedia)
134 64000 bps (multimedia)
all other values below 256 are reserved by the present document.
<name>: integer type
0 data circuit asynchronous (UDI or 3.1 kHz modem)
1 data circuit synchronous (UDI or 3.1 kHz modem)
2 PAD Access (asynchronous) (UDI)
3 Packet Access (synchronous) (UDI)
4 data circuit asynchronous (RDI)
5 data circuit synchronous (RDI)
6 PAD Access (asynchronous) (RDI)
7 Packet Access (synchronous) (RDI)
all other values below 128 are reserved by the present document.
<ce>: integer type
0 transparent
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
38
3GPP TS 27.007 version 13.3.0 Release 13
1 non-transparent
2 both, transparent preferred
3 both, non-transparent preferred
Implementation
Mandatory when data calls implemented.
6.8 Radio link protocol +CRLP
Table 15: +CRLP parameter command syntax
Command
Possible response(s)
+CRLP=[<iws>[,<mws>[,<T1>
[,<N2>[,<ver>[,<T4>]]]]]]
+CRLP? +CRLP: <iws>,<mws>,<T1>,<N2>[,<ver1>[,<T4>]]
[<CR><LF>+CRLP: <iws>,<mws>,<T1>,<N2>[,<ver2>[,<T4>]]
[...]]
+CRLP=? +CRLP: (list of supported <iws>s),(list of supported <mws>s),
(list of supported <T1>s),(list of supported <N2>s)[,<ver1>
[,(list of supported <T4>s)]]
[<CR><LF>+CRLP: (list of supported <iws>s),(list of supported
<mws>s),(list of supported <T1>s),(list of supported <N2>s)
[,<ver2>[,(list of supported <T4>s)]]
[...]]
Description
Radio link protocol (RLP) parameters used when non-transparent data calls are originated may be altered with set
command. Available command subparameters depend on the RLP versions implemented by the device (e.g. <ver>
may not be available if device supports only versions 0 and 1).
NOTE 1: If radio link protocol is not used, but some other error correcting protocol (for transparent data calls),
ITU-T Recommendation V.250 [14] Error Control Selection test command +ES=? may be used to
indicate the presence of the protocol.
Read command returns current settings for each supported RLP version <verx>. Only RLP parameters applicable to
the corresponding <verx> are returned.
Test command returns values supported as compound values. If MT/TA supports several RLP versions <verx>, the
RLP parameter value ranges for each <verx> are returned on a separate line.
Defined values
<ver>, <verx>: RLP version number in integer format; when version indication is not present it shall equal 0
NOTE 2: Versions 0 and 1 share the same parameter set. Read and test commands shall return only one line for this
set (where <verx> is not present).
<iws>, <mws>, <T1>, <N2>, <T4>: IWF to MS window size, MS to IWF window size, acknowledgement timer
T1, retransmission attempts N2, re-sequencing period T4 in integer format (default values and value ranges
depend on RLP version; refer 3GPP TS 24.022 [18]): T1 and T4 are in units of 10 ms.
Implementation
Mandatory when RLP implemented.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
39
3GPP TS 27.007 version 13.3.0 Release 13
6.9 Service reporting control +CR
Table 16: +CR parameter command syntax
Command
Possible response(s)
+CR=[<mode>]
+CR? +CR: <mode>
+CR=? +CR: (list of supported <mode>s)
Description
Set command controls whether or not intermediate result code +CR: <serv> is returned from the TA to the TE. If
enabled, the intermediate result code is transmitted at the point during connect negotiation at which the TA has
determined which speed and quality of service will be used, before any error control or data compression reports are
transmitted, and before the intermediate result code CONNECT is transmitted.
NOTE: This command replaces ITU-T Recommendaion V.250 [14] command Modulation Reporting Control
+MR, which is not appropriate for use in the GSM/UMTS network. Possible error control (other than radio
link protocol) and data compression reporting can be enabled with V.250 commands Error Control
Reporting +ER and Data Compression Reporting +DR.
Read command returns the current value of <mode>.
Test command returns values supported as a compound value.
Defined values
<mode>: integer type
0 disables reporting
1 enables reporting
<serv>:
ASYNC asynchronous transparent
SYNC synchronous transparent
REL ASYNC asynchronous non-transparent
REL SYNC synchronous non-transparent
GPRS [<L2P>] GPRS
<L2P>: proposes a layer 2 protocol to use between the MT and the TE. It is defined in the Enter GPRS Data Mode
(+CGDATA) command.
Implementation
Mandatory when data calls implemented.
6.10 Extended error report +CEER
Table 17: +CEER action command syntax
Command
Possible response(s)
+CEER +CEER: <report>
+CEER=?
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
40
3GPP TS 27.007 version 13.3.0 Release 13
Description
Execution command causes the TA to return one or more lines of information text <report>, determined by the MT
manufacturer, which should offer the user of the TA an extended report of the reason for
- the failure in the last unsuccessful call setup (originating or answering) or in-call modification;
- the last call release;
- the last unsuccessful GPRS attach or unsuccessful PDP context activation;
- the last GPRS detach or PDP context deactivation.
Typically, the text will consist of a single line containing the cause information given by GSM/UMTS network in
textual format.
Defined values
<report>: the total number of characters, including line terminators, in the information text shall not exceed 2041
characters.
Text shall not contain the sequence 0<CR> or OK<CR>.
Implementation
Optional.
6.11 Cellular result codes +CRC
Table 18: +CRC parameter command syntax
Command
Possible response(s)
+CRC=[<mode>]
+CRC? +CRC: <mode>
+CRC=? +CRC: (list of supported <mode>s)
Description
Set command controls whether or not the extended format of incoming call indication or GPRS network request for
PDP context activation or notification for VBS/VGCS calls is used. When enabled, an incoming call is indicated to the
TE with unsolicited result code +CRING: <type> instead of the normal RING.
Read command returns the current value of <mode>.
Test command returns values supported as a compound value.
NOTE 1: Similar command may be found in TIA IS-99 [15] and TIA IS-135 [16].
Defined values
<mode>: integer type
0 disables extended format
1 enables extended format
<type>:
ASYNC [,<priority>[,<subaddr>,<satype>]] asynchronous transparent
SYNC [,<priority>[,<subaddr>,<satype>]] synchronous transparent
REL ASYNC [,<priority>[,<subaddr>,<satype>]] asynchronous non-transparent
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
41
3
GPP TS 27.007 version 13.3.0 Release 13
REL SYNC [,<priority>[,<subaddr>,<satype>]] synchronous non-transparent
FAX [,<priority>[,<subaddr>,<satype>]] facsimile (TS 62)
VOICE [,<priority>[,<subaddr>,<satype>]] normal voice (TS 11) (see
NOTE 2)
VOICE/VIDEO [,<ccidx>[,<priority>[,<subaddr>,<satype>]]] voice or video call (see
NOTE 2)
VOICE/XXX [,<priority>[,<subaddr>,<satype>]] voice followed by data (BS 81)
(XXX is ASYNC, SYNC, REL
ASYNC or REL SYNC)
ALT VOICE/XXX [,<priority>[,<subaddr>,<satype>]] alternating voice/data, voice first
(BS 61)
ALT XXX/VOICE [,<priority>[,<subaddr>,<satype>]] alternating voice/data, data first
(BS 61)
ALT VOICE/FAX [,<priority>[,<subaddr>,<satype>]] alternating voice/fax, voice first
(TS 61)
ALT FAX/VOICE [,<priority>[,<subaddr>,<satype>]] alternating voice/fax, fax first
(TS 61)
GPRS <PDP_type>, <PDP_addr>[, [<L2P>][,<APN>]] GPRS network request for PDP
context activation
VGC <GCA>, <GId>, <ackflag> [,<priority>] voice group call (TS 91)
VBC <GCA>, <GId>, <ackflag> [,<priority>] voice broadcast call (TS 92)
NOTE 2: The <type>=VOICE/VIDEO is used for voice and/or video calls. It is implementation specific whether
this type will replace the <type>=VOICE or if both the types <type>=VOICE/VIDEO and
<type>=VOICE are supported.
<priority>: indicates the eMLPP priority level of the incoming call by paging, notification or setup message.
The priority level values are as defined in eMLPP specification 3GPP TS 22.067 [54].
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8) or
RFC 4715 [122] appendix A.
<ccidx>: integer type. Call identification number, see +CLCCS.
<PDP_type>, <PDP_addr> and <APN>: string types as defined in the Define PDP Context (+CGDCONT)
command.
<L2P>: string type proposes a layer 2 protocol to use between the MT and the TE. It is defined in the Enter GPRS
Data Mode (+CGDATA) command. If the MT is unable to announce to the TE the network's request (for example
it is in V.250 online data state) the MT shall reject the request. No corresponding unsolicited result code shall be
issued when the MT returns to a command state.
<GCA>: string type (consisting of digits only) is a part of the group call reference as specified in
3GPP TS 23.003 [7] and indicates group call area. See the commands +CAJOIN, +CAREJ and +CALCC.
<GId>: string type (consisting of digits only) is a part of the group call reference as specified in
3GPP TS 23.003 [7] and indicates group call identification. See the commands +CAJOIN, +CAREJ and
+CALCC.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
42
3GPP TS 27.007 version 13.3.0 Release 13
<ackflag>: integer type proposes that a predefined confirmation procedure is to be used after the call is ended.
The value 1 indicates that a predefined confirmation procedure is to be used after the call is ended. The value 0
indicates that no confirmation procedure is required. See the parameter <ack_flag> of command +CALCC.
Implementation
Mandatory when data or fax circuit mode calls are implemented, or for an MT supporting AT commands only and
eMLPP or VGCS or VBS is implemented.
6.12 HSCSD device parameters +CHSD
Table 19: +CHSD action command syntax
Command
Possible response(s)
+CHSD +CHSD: <mclass>,<maxRx>,<maxTx>,<sum>,<codings>
+CME ERROR: <err>
+CHSD=?
Description
Execution command returns information about HSCSD features (refer 3GPP TS 22.034 [29]) supported by the MT/TA.
Refer subclause 9.2 for possible <err> values.
The return information is only applicable in GERAN.
Defined values
<mclass>: integer type; multislot class
<maxRx>: integer type; maximum number of receive timeslots that MT can use
<maxTx>: integer type; maximum number of transmit timeslots that MT can use
<sum>: integer type; total number of receive and transmit timeslots that MT can use at the same time (per TDMA
frame). The following applies in a HSCSD call: 1 ≤ (receive slots) + (transmit slots) ≤ <sum>
<codings>: is a sum of integers each representing a supported channel coding (e.g. value 5 indicates that 4,8k and
9,6k channel codings are supported):
1 4,8k full rate data traffic channel
4 9,6k full rate data traffic channel
8 14,4k full rate data traffic channel
16 28,8k full rate data traffic channel (only possible when 14.4k is supported)
32 32,0k full rate data traffic channel (only possible in a two-timeslot configuration)
64 43,2k full rate data traffic channel (only possible when 14.4k is supported)
Implementation
Mandatory when HSCSD implemented.
This command is not applicable to UTRAN or E-UTRAN UEs.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
43
3GPP TS 27.007 version 13.3.0 Release 13
6.13 HSCSD transparent call configuration +CHST
Table 20: +CHST parameter command syntax
Command
Possible response(s)
+CHST=[<wRx>[,<codings>]]
+CHST? +CHST: <wRx>,<codings>
+CHST=?
Description
Set command controls parameters for transparent HSCSD calls in GERAN. Changing them during a call does not affect
the current call.
Read command returns the current values.
NOTE: In UTRAN or E-UTRAN, values set with this command are not needed. The only applicable parameter is
<SPEED>, which is set with +CBST command.
Defined values
<wRx>: integer type; wanted amount of receive timeslots. Default value 0 indicates that TA shall calculate a proper
value from currently selected fixed network user rate (<speed> subparameter from +CBST command) and
<codings>
<codings>: a sum of integers each representing a channel coding that is accepted for transparent HSCSD calls.
Default value 0 indicates that all supported codings are accepted (refer +CHSD command for other values)
Implementation
Mandatory when transparent HSCSD implemented.
This command is not applicable to UTRAN or E-UTRAN UEs.
6.14 HSCSD non-transparent call configuration +CHSN
Table 21: +CHSN parameter command syntax
Command
Possible response(s)
+CHSN=[<wAiur>[,<wRx>[,<topRx>
[,<codings>]]]]
+CHSN? +CHSN: <wAiur>,<wRx>,<topRx>,<codings>
+CHSN=? +CHSN: (list of supported <wAiur>s),(list of supported
<wRx>s),(list of supported <topRx>s),(list of
supported <codings>s)
Description
Set command controls parameters for originating non-transparent HSCSD calls. Values may also be used during mobile
terminated data call setup. In GERAN, changing <topRx> or <codings> value during a call does not affect the
current call. In GERAN, changing of <wAiur> or <wRx> affects the current call only if <topRx> was non-zero when
call was established.
Read command returns the current values.
Test command returns values supported as compound values.
Defined values
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
44
3GPP TS 27.007 version 13.3.0 Release 13
<wAiur>: integer type; wanted air interface user rate. Default value 0 indicates that TA shall calculate a proper
value from currently selected fixed network user rate (<speed> subparameter from +CBST command),
<codings>, and <wRx> (or <maxRx> from +CHSD command if <wRx>=0). Other values:
1 9600 bps
2 14400 bps
3 19200 bps
4 28800 bps
5 38400 bps
6 43200 bps
7 57600 bps
<wRx>: integer type; wanted amount of receive timeslots. Default value 0 indicates that TA shall calculate a proper
value from currently selected <wAiur> and <codings>. This parameter is not applicable to UTRAN or E-
UTRAN UEs.
<topRx>: integer type; top value for <wRx> that user is going to request during the next established non-
transparent HSCSD call. Default value 0 indicates that user is not going to change <wAiur>/<wRx> during the
next call. This parameter is not applicable to UTRAN or E-UTRAN UEs.
<codings>: a sum of integers each representing a channel coding that is accepted for non-transparent HSCSD
calls. Default value 0 indicates that all supported codings are accepted (refer +CHSD command for other values).
This parameter is not applicable to UTRAN or E-UTRAN UEs.
Implementation
Mandatory when non-transparent HSCSD implemented.
6.15 HSCSD current call parameters +CHSC
Table 22: +CHSC action command syntax
Command
Possible response(s)
+CHSC +CHSC: <rx>,<tx>,<aiur>,<coding>
+CHSC=?
Description
Execution command returns information about current HSCSD call. If no HSCSD call is active, all parameters returned
shall equal zero. If HSCSD call is active in UTRAN or E-UTRAN, all non-applicable parameters returned shall be
equal to zero. (It is manufacturer specific whether non-zero information is returned in case of an active normal single-
slot data call.)
Defined values
<rx>: integer type; number of receive timeslots currently in use. This parameter is not applicable in UTRAN or E-
UTRAN.
<tx>: integer type; number of transmit timeslots currently in use. This parameter is not applicable in UTRAN or E-
UTRAN.
<aiur>: integer type; current air interface user rate (in case of transparent service this equals fixed network user
rate) (refer +CHSN command for possible values). For the two-timeslot ECSD bit transparent configuration the
following additional values apply:
8 56000 bps
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
45
3GPP TS 27.007 version 13.3.0 Release 13
9 64000 bps
<coding>: is a sum of integers each representing the current channel coding (refer +CHSD command for possible
values). This parameter is not applicable in UTRAN or E-UTRAN.
Implementation
Optional.
6.16 HSCSD parameters report +CHSR
Table 23: +CHSR parameter command syntax
Command
Possible response(s)
+CHSR=[<mode>]
+CHSR? +CHSR: <mode>
+CHSR=? +CHSR: (list of supported <mode>s)
Description
Enabled command returns intermediate result code +CHSR: <type> from the TA to the TE when an HSCSD call is
being set up. The result code represents the current (negotiated or renegotiated) HSCSD parameters. If enabled, the
intermediate result code is transmitted at the point of the call setup negotiation where the TA has determined what type
of an HSCSD connection will be used. Result code transmission is done after possible service (+CR), error control
(+ER), and/or compression (+DR) reporting but before possible TE-TA rate (+ILRR) reporting and before the
intermediate result code CONNECT is transmitted. The format of the intermediate result code is:
+CHSR: <rx>,<tx>,<aiur>,<coding>
For the value definitions, refer to +CHSN and +CHSC commands. For instance, for a non-transparent HSCSD call, result
code '+CHSR: 2,2,4,8' means that the call has two timeslots in both up- and downlink, the air interface user rate is
28800 bps, and the used channel coding TCH/F14.4.
In UTRAN or E-UTRAN, all non-applicable parameters returned shall be equal to zero.
Read command returns the current value of <mode>.
Test command returns the values supported by the UE as a compound value.
Defined values
<mode>: integer type
0 disables reporting
1 enables reporting
Implementation
Mandatory when HSCSD implemented
6.17 HSCSD automatic user initiated upgrading +CHSU
Table 24: +CHSU parameter command syntax
Command
Possible response(s)
+CHSU=<mode>
+CHSU? +CHSU: <mode>
+CHSU=? +CHSU: (list of supported <mode>s)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
46
3GPP TS 27.007 vers
ion 13.3.0 Release 13
Description
Set command controls whether or not automatic user initiated service level upgrading shall be used for non-transparent
HSCSD calls. "Automatic" means that, if enabled, the ME/TA shall use the UP bit in the received RLP frames to
determine when to initiate user initiated service level upgrading (i.e. when to modify the +CHSN parameters <wAiur>
and/or <wRx> for the current call). Refer to 3GPP TS 27.001 [41] for details on the interpretation of the UP bit(s).
Read command returns the current value of <mode>.
Test command returns values supported as a compound value.
NOTE 1: The validity of the UP bit in the RLP frames depends on the result of the RLP negotiations. The UP bit
shall only be used if the result of the RLP negotiations were successful with respect to the UP bit.
NOTE 2: This command is only applicable in GERAN.
Defined values
<mode>: integer type
0 disables use of UP bit for upgrading
1 enables use of UP bit for upgrading
Implementation
Optional
This command is not applicable to UTRAN or E-UTRAN UEs.
6.18 HSCSD non-transparent asymmetry configuration +CHSA
Table 25: +CHSA parameter command syntax
Command
Possible response(s)
+CHSA=<mode>
+CHSA? +CHSA: <mode>
+CHSA=? +CHSA: (list of supported <mode>s)
Description
Set command controls the preferred asymmetry bias for non-transparent ECSD calls. Downlink biased asymmetry
means that 8-PSK modulation is preferred downlink and GMSK modulation uplink. Uplink based asymmetry means
that 8-PSK modulation is preferred uplink and GMSK downlink. Changing of <mode> affects the current call only if
<topRx> (refer +CHSN) was non-zero when call was established.
Read command returns the current value of <type>.
Test command returns values supported by the MT/TA as a compound value. The <mode> subparameter range
indirectly indicates the UE Type; range (0-1) indicates UE Type A and range (0-2) indicates UE Type B.
NOTE 1: ECSD is also controlled by +CHSD, +CHSN and +CHST.
NOTE 2: This command is only applicable in GERAN.
Defined values
<mode>: integer type
0 No preference
1 Downlink biased asymmetry
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
47
3GPP TS 27.007 version 13.3.0 Release 13
2 Uplink biased asymmetry
Implementation
Mandatory when non-transparent ECSD is implemented.
This command is not applicable to UTRAN or E-UTRAN UEs.
6.19 Single numbering scheme +CSNS
Table 26: +CSNS parameter command syntax
Command
Possible response(s)
+CSNS=[<mode>]
+CSNS? +CSNS: <mode>
+CSNS=? +CSNS: (list of supported <mode>s)
Description
Set command selects the bearer or teleservice to be used when mobile terminated single numbering scheme call is
established. Parameter values set with +CBST command shall be used when <mode> equals to a data service.
Read command returns the current value of <mode>.
Test command returns values supported as a compound value.
Defined values
<mode>: integer type
0 voice
1 alternating voice/fax, voice first (TS 61)
2 fax (TS 62)
3 alternating voice/data, voice first (BS 61)
4 data
5 alternating voice/fax, fax first (TS 61)
6 alternating voice/data, data first (BS 61)
7 voice followed by data (BS 81)
Implementation
Optional.
6.20 Voice hangup control +CVHU
Table 27: +CVHU parameter command syntax
Command
Possible response(s)
+CVHU=[<mode>]
+CVHU? +CVHU: <mode>
+CVHU=? +CVHU: (list of supported <mode>s)
ETSI
ETSI TS 12
7 007 V13.3.0 (2016
-
03)
48
3GPP TS 27.007 version 13.3.0 Release 13
Description
Set command selects whether ATH or "drop DTR" shall cause a voice connection to be disconnected or not. By voice
connection is also meant alternating mode calls that are currently in voice mode. (See subclause 6.6).
Read command returns the current value of <mode>.
Test command returns values supported as a compound value.
NOTE: When <mode> = 2, this command must be seen in conjunction with the
ITU-T Recommendation V.250 [14] command &D. Else &D shall be ignored.
Defined values
<mode>: integer type
0 "Drop DTR" ignored but OK response given. ATH disconnects.
1 "Drop DTR" and ATH ignored but OK response given.
2 "Drop DTR" behaviour according to &D setting. ATH disconnects.
Implementation
Optional
6.21 CCITT V.120 [36] rate adaption protocol +CV120
Table 28: +CV120 parameter command syntax
Command
Possible response(s)
+CV120=[<rah>[,<mfm>[,<mo
de>[,<llineg>[,<assign>[,
<negtype>]]]]]]
+CV120? +CV120: <rah>,<mfm>,<mode>,<llineg>,<assign
>,<negtype>
+CV120=? +CV120: (list of supported <rah>s),(list of supported
<mfm>s),(list of supported <mode>s),(list of supported
<llineg>s),(list of supported <assign>s),(list of
supported <negtype>s)
Description
Set command sets the values of the V.120 protocol parameters (defined in CCITT Recommendation V.120 [36]) that
are carried in the GSM BC and/or LLC information elements.
Read command returns current settings for the V.120 parameters.
Test command returns values supported as compound values.
Defined values
<rah>: integer type
0 rate adaption header not included
1 rate adaption header included (mandatory for protocol sensitive modes).
<mfm>: integer type
0 multiple frame establishment not supported, only UI frames allowed
1 multiple frame establishment supported, both I and UI frames allowed.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
49
3GPP TS 27.007 version 13.3.0 Release 13
<mode>: integer type
0 bit transparent mode of operation
1 protocol sensitive mode of operation.
<llineg>: integer type
0 no negotiation, LLI = 256 only
1 negotiation allowed.
NOTE: <negtype> indicates the connection over which the negotiation is performed.
<assign>: integer type
0 message originator is "default assignee"
1 message originator is "assignor only".
<negtype>: integer type
0 negotiation is done using logical link zero
1 negotiation is done with USER INFORMATION messages on a temporary signalling connection.
GSM/UMTS does not support all the possible modes of V.120 operation. However, in order to accommodate possible
future additions, the complete set of parameters is included in the command.
The permitted values are: 1, 1 or 0, 1, 0, 0, 0.
A recommended set of default values is: 1, 1, 1, 0, 0, 0.
Implementation
Mandatory, if the MT supports V.120 interworking.
6.22 Settings date format +CSDF
Table 29: +CSDF parameter command syntax
Command
Possible response(s)
+CSDF=[[<mode>][,<auxmode>]] +CME ERROR: <err>
+CSDF? +CSDF: <mode>[,<auxmode>]
+CME ERROR: <err>
+CSDF=? +CSDF: (list of supported <mode>s)
[,(list of supported <auxmode>s)]
+CME ERROR: <err>
Description
This command sets the date format via MMI of the date information presented to the user, which is specified by use of
the <mode> parameter. The <mode> affects the date format on the phone display and doesn't affect the date format of
the AT command serial interface. The command also sets the date format of the TE-TA interface, which is specified by
use of the <auxmode> parameter (e.g. the <auxmode> affects the <time> of +CCLK and +CALA). If the parameter is
omitted ("+CSDF=","+CSDF=<mode>","+CSDF=,<auxmode>"), then this sets the default value. Refer
subclause 9.2 for possible <err> values.
Read command returns the current settings.
Test command returns values supported as compound values.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
50
3GPP TS 27.007 version 13.3.0 Release 13
Defined values
<mode>: integer type
NOTE 1: It is manufacturer specific which modes that are supported.
1 DD-MMM-YYYY
NOTE 2: Presentation of MMM is language dependent.
2 DD-MM-YY
3 MM/DD/YY
4 DD/MM/YY
5 DD.MM.YY
6 YYMMDD
7 YY-MM-DD
8-255 Manufacturer specific
<auxmode>: integer type
1 yy/MM/dd
2 yyyy/MM/dd
all other values are reserved by the present document
NOTE 3: The <time> format of +CCLK and +CALA "yy/MM/dd,hh:mm:ss±zz" when <auxmode>=1 and it is
"yyyy/MM/dd,hh:mm:ss±zz" when <auxmode>=2. If the MT does not support time zone information
then the three last characters may be omitted (see +CCLK command).
Implementation
Optional
6.23 Silence command +CSIL
Table 30: +CSIL parameter command syntax
Command
Possible response(s)
+CSIL=[<mode>] +CME ERROR: <err>
+CSIL? +CSIL: <mode>
+CME ERROR: <err>
+CSIL=? +CSIL: (list of supported <mode>s)
+CME ERROR: <err>
Description
Set command enables/disables the silent mode. When the phone is in silent mode, all sounds from MT are suppressed
except voice. Refer subclause 9.2 for possible <err> values.
Read command reads the current setting.
Test command lists the supported modes as a compound value.
Defined values
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
51
3GPP TS 27.007 version 13.3.0 Release
13
<mode>: integer type. The default value is manufacturer specific.
0 Silent mode off
1 Silent mode on
Implementation
Optional
6.24 Settings time format +CSTF
Table 31: +CSTF parameter command syntax
Command
Possible
response(s)
+CSTF=[<mode>] +CME ERROR: <err>
+CSTF? +CSTF: <mode>
+CME ERROR: <err>
+CSTF=? +CSTF: (list of supported <mode>s)
+CME ERROR: <err>
Description
Set command sets the time format of the time information presented to the user. Refer subclause 9.2 for possible
<err> values.
Read command reads the current setting.
Test command reads the supported <modes>s as a compound value.
Defined values
<mode>: integer type. The default value is manufacturer specific.
1 HH:MM (24 hour clock)
2 HH:MM a.m./p.m.
3-7 Manufacturer specific
Implementation
Optional
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
52
3GPP TS 27.007 version 13.3.0 Release 13
6.25 ITU-T Recommendation V.250 [14] call control commands
Table 32: V.250 call control commands
Command
Subclause
Impl.
Use in GSM/UMTS
D[<dial_strin
g>][;] 6.3.1 mand.
originates a call
T 6.3.2 mand.
ignored (select tone dialling)
P 6.3.3 mand.
ignored (select pulse dialling)
A 6.3.5 mand.
answer a call
H[<value>] 6.3.6 mand.
hang-up a single mode call; for alternate mode call refer subclause
"Hangup call +CHUP" (only value equal to zero needed)
O[<value>] 6.3.7 mand.
returns TA to online data state from online command mode (only value
equal to zero needed)
S0=[<value>] 6.3.8 mand.
sets the number of call indications (rings) before automatically
answering the call; value equalling zero disables automatic answering
and is the default
S6=[<value>] 6.3.9 mand.
ignored (pause before blind dialling)
S7=[<value>] 6.3.10 mand.
sets number of seconds to wait for completion of call answering or
originating procedure before giving up and disconnecting
S8=[<value>] 6.3.11 mand.
sets number of seconds to wait when comma dial modifier encountered
in dial string of D command (default is 2 seconds)
S10=[<value>] 6.3.12 mand.
sets number of tenths of seconds to wait before disconnecting after TA
has indicated the absence of received line signal
L[<value>] 6.3.13 mand.
ignored (monitor speaker loudness)
M[<value>] 6.3.14 mand.
ignored (monitor speaker mode)
Implementation of commands marked as mandatory is mandatory only if call control functionality is supported.
6.26 ITU-T Recommendation V.250 [14] data compression
commands
Table 33: V.250 data compression commands
Command
Subclause
Impl.
Use in GSM/UMTS
+DS=[<dir>[,<neg>[
,<P1>[,<P2>]]]] 6.6.1 mand.
when
V.42bis
controls ITU-T Recommendation V.42bis data compression
functions; for subparameter defaults in GSM/UMTS refer
3GPP TS 24.022 [18]
+DR=[<value>] 6.6.2 mand.
when
V.42bis
determines whether the use of V.42bis is informed using
intermediate result code +DR: <type> before going
online data state after call answering or originating
6.27 Initiate eCall +CECALL
Table 6.27-1: +CECALL parameter command syntax
Command
Possible response
+CECALL=<type_of_eCall>
+CECALL? +CECALL: [<type_of_eCall>]
+CECALL=? +CECALL: (list of supported <type_of_eCall>s)
Description
13
ETSI
ETSI TS 127 007 V13.3.0 (201
6
-
03)
53
3GPP TS 27.007 version 13.3.0 Release 13
Set command is used to trigger an eCall to the network. Based on the configuration selected, it can be used to either
trigger a test call, a reconfiguration call, a manually initiated eCall or an automatically initiated eCall.
Read command returns the type of eCall that is currently in progress, if any.
Test command returns the supported values as a compound value.
Defined values
<type_of_eCall>: integer type
0 test call
1 reconfiguration call eCall
2 manually initiated eCall
3 automatically initated eCall
Implementation
Optional.
6.28 Informative examples
The alternating mode call handling (voice and fax, or voice and data) and the data call setup commands are defined such
that the dialling command of ITU-T Recommendation V.250 [14] (D) still always originates a call. The purpose is to
support all current TE applications using the dialling command as default. Fax calls are controlled following the rules of
ITU-T Recommendation T.31 [11] and ITU-T Recommendation T.32 [12] standards.
An example where a voice call is originated:
ATD+1 812 555673I; (type of address defaults to 145, CLI presentation is restricted for this call)
OK (call setup was successful)
An example where a voice call is attempted from a phonebook:
ATD>"Doe Joe"G; (enable CUG control for this call)
+CME ERROR: 22 (entry "Doe Joe" is not found)
Also supplementary services may be controlled using dial command according to 3GPP TS 22.030 [19]. An example of
call forwarding on no reply for telephony with the adjustment of the no reply condition timer on 25 seconds:
ATD**61*+1812555673*11*25#
OK (modification was successful)
Two new commands are created for controlling the alternating mode calls. First one, Call Mode (+CMOD), selects
between single and alternating mode. Because this is a crucial command, it is defined that the value is set back to
zero (single mode) after every successfully originated alternating mode call. Also on power-up and factory or user
resets, the value is set to zero. The second new command, Hangup Call (+CHUP), is not a replacement of
ITU-T Recommendation V.250 [14] command H, but a command which reliably disconnects the call in GSM/UMTS
network. This is defined because the H command is used to switch from fax or data mode to voice mode.
The setting of GSM/UMTS bearer service (data circuit duplex asynchronous and synchronous, PAD access circuit
asynchronous, or data packet duplex synchronous), is done with Select Bearer Service Type (+CBST). It chooses one of
the four mentioned bearer services, the data rate of the service (or actually the modulation when modem IWFs are
used), and enables or disables RLP. Command Radio Link Protocol (+CRLP) is used to set the RLP parameters in the
radio path.
Service Reporting Control command (+CR) is defined similarly as the reporting of modulation, V.18, error control, and
data compression which are ITU-T Recommendation V.250 [14] features used to show information about the type of
the established connection before the CONNECT intermediate result code. +CR command has one subparameter which
specifies whether the intermediate result code +CR: <serv> is returned or not. The result code should be returned
before any ITU-T Recommendation V.250 [14] reporting result codes. An example of setting up an asynchronous
9600 bit/s modem connection with service reporting:
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
54
3GPP TS 27.007 version 13.3.0 Release 13
AT+CBST=7,0,1 (asynchronous modem 9600 bit/s and RLP)
OK
AT+CR=1 (enable reporting)
OK
ATD1234567890
+CR: REL ASYNC
CONNECT 9600
As GSM/UMTS network offers more information about the reason of the failure in call originating and answering than
normal PSTN, it is useful to add an extra command to return this information to the TE. This information should not be
returned always after unsuccessful call originating or answering, because many TE applications look for just the regular
NO CARRIER, BUSY, NO ANSWER and CONNECT messages. Action command Extended Error Report (+CEER) does
not have any subparameters, and it returns the cause of the latest call setup failure. This information may be the textual
presentation of the GSM/UMTS network failure code (refer 3GPP TS 24.008 [8] Annex H), or some other information
defined by the TA manufacturer.
7 Network service related commands
7.0 General
This clause describes GSM/UMTS network related commands, which are not covered in call control clause of the
present document. Commands include GSM/UMTS supplementary service handling, MSISDN query, MT and network
facility locking, and network registration information query.
7.1 Subscriber number +CNUM
Table 34: +CNUM action command syntax
Command
Possible response(s)
+CNUM +CNUM: [<alpha1>],<number1>,<type1>[,<speed>,<service>[,<itc>]]
[<CR><LF>+CNUM: [<alpha2>],<number2>,<type2>[,<speed>,<service>
[,<itc>]]
[...]]
+CME ERROR: <err>
+CNUM=?
Description
Action command returns the MSISDNs related to the subscriber (this information can be stored in the SIM/UICC or in
the MT). When storing information in the SIM/UICC, if the currently selected card slot contains a SIM card or a UICC
with an active GSM application, the information is stored in the EF
MSISDN
under DF
Telecom
. If the currently selected card
slot contains a UICC with an active USIM application, the information is stored in the EF
MSISDN
under ADF
USIM
). If
subscriber has different MSISDN for different services, each MSISDN is returned on a separate line. Refer
subclause 9.2 for possible <err> values.
Defined values
<alphax>: optional alphanumeric string associated with <numberx>; used character set should be the one
selected with command Select TE Character Set +CSCS
<numberx>: string type phone number of format specified by <typex>
<typex>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<speed>: integer type as defined in subclause 6.7
<service>: integer type (service related to the phone number)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
55
3GPP TS 27.007 version 13.3.0 Release 13
0 asynchronous modem
1 synchronous modem
2 PAD Access (asynchronous)
3 Packet Access (synchronous)
4 voice
5 fax
all other values below 128 are reserved by the present document
<itc>: integer type (information transfer capability)
0 3,1 kHz
1 UDI
Implementation
Optional.
7.2 Network registration +CREG
Table 35: +CREG parameter command syntax
Command
Possible response(s)
+CREG=[<n>] +CME ERROR: <err>
+CREG? +CREG: <n>,<stat>[,[<lac>],[<ci>],[<AcT>]
[,<cause_type>,<reject_cause>]]
+CREG=? +CREG: (list of supported <n>s)
Description
Set command controls the presentation of an unsolicited result code +CREG: <stat> when <n>=1 and there is a
change in the MT"s circuit mode network registration status in GERAN/UTRAN/E-UTRAN, or unsolicited result code
+CREG: <stat>[,[<lac>],[<ci>],[<AcT>]] when <n>=2 and there is a change of the network cell in
GERAN/UTRAN/E-UTRAN. The parameters <AcT>, <lac> and <ci> are sent only if available. The value <n>=3
further extends the unsolicited result code with [,<cause_type>,<reject_cause>], when available, when the
value of <stat> changes.
NOTE 1: If the MT also supports GPRS services and/or EPS services, the +CGREG command and +CGREG: result
codes and/or the +CEREG command and +CEREG: result codes apply to the registration status and
location information for those services.
Read command returns the status of result code presentation and an integer <stat> which shows whether the network
has currently indicated the registration of the MT. Location information elements <lac>, <ci> and <AcT>, if
available, are returned only when <n>=2 and MT is registered in the network. The parameters
[,<cause_type>,<reject_cause>], if available, are returned when <n>=3. Refer subclause 9.2 for possible
<err> values.
Test command returns values supported as a compound value.
Defined values
<n>: integer type
0 disable network registration unsolicited result code
1 enable network registration unsolicited result code +CREG: <stat>
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
56
3GPP TS 27.007 version 13.3.0 Release 13
2 enable network registration and location information unsolicited result code
+CREG: <stat>[,[<lac>],[<ci>],[<AcT>]]
3 enable network registration, location information and cause value information unsolicited result code
+CREG: <stat>[,[<lac>],[<ci>],[<AcT>][,<cause_type>,<reject_cause>]]
<stat>: integer type; circuit mode registration status
0 not registered, MT is not currently searching a new operator to register to
1 registered, home network
2 not registered, but MT is currently searching a new operator to register to
3 registration denied
4 unknown (e.g. out of GERAN/UTRAN/E-UTRAN coverage)
5 registered, roaming
6 registered for "SMS only", home network (applicable only when <AcT> indicates E-UTRAN)
7 registered for "SMS only", roaming (applicable only when <AcT> indicates E-UTRAN)
8 attached for emergency bearer services only (see NOTE 2) (not applicable)
9 registered for "CSFB not preferred", home network (applicable only when <AcT> indicates E-UTRAN)
10 registered for "CSFB not preferred", roaming (applicable only when <AcT> indicates E-UTRAN)
NOTE 2: 3GPP TS 24.008 [8] and 3GPP TS 24.301 [83] specify the condition when the MS is considered as
attached for emergency bearer services.
<lac>: string type; two byte location area code (when <AcT> indicates value 0 to 6), or tracking area code (when
<AcT> indicates value 7). In hexadecimal format (e.g. "00C3" equals 195 in decimal).
<ci>: string type; four byte GERAN/UTRAN/E-UTRAN cell ID in hexadecimal format.
<AcT>: integer type; access technology of the serving cell
0 GSM
1 GSM Compact
2 UTRAN
3 GSM w/EGPRS (see NOTE 3)
4 UTRAN w/HSDPA (see NOTE 4)
5 UTRAN w/HSUPA (see NOTE 4)
6 UTRAN w/HSDPA and HSUPA (see NOTE 4)
7 E-UTRAN
NOTE 3: 3GPP TS 44.060 [71] specifies the System Information messages which give the information about
whether the serving cell supports EGPRS.
NOTE 4: 3GPP TS 25.331 [74] specifies the System Information blocks which give the information about whether
the serving cell supports HSDPA or HSUPA.
<cause_type>: integer type; indicates the type of <reject_cause>.
0 Indicates that <reject_cause> contains an MM cause value, see 3GPP TS 24.008 [8] Annex G.
1 Indicates that <reject_cause> contains a manufacturer specific cause.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
57
3GPP TS 27.007 version 13.3.0 Release 13
<reject_cause>: integer type; contains the cause of the failed registration. The value is of type as defined by
<cause_type>.
Implementation
Optional.
7.3 PLMN selection +COPS
Table 36: +COPS parameter command syntax
Command
Possible response(s)
+COPS=[<mode>[,<format>
[,<oper>[,<AcT>]]]] +CME ERROR: <err>
+COPS? +COPS: <mode>[,<format>,<oper>[,<AcT>]]
+CME ERROR: <err>
+COPS=? +COPS: [list of supported (<stat>,long alphanumeric <oper>,short
alphanumeric <oper>,numeric <oper>[,<AcT>])s][,,(list of
supported <mode>s),(list of supported <format>s)]
+CME ERROR: <err>
Description
Set command forces an attempt to select and register the GSM/UMTS/EPS network operator using the SIM/USIM card
installed in the currently selected card slot. <mode> is used to select whether the selection is done automatically by the
MT or is forced by this command to operator <oper> (it shall be given in format <format>) to a certain access
technology, indicated in <AcT>. If the selected operator is not available, no other operator shall be selected (except
<mode>=4). If the selected access technology is not available, then the same operator shall be selected in other access
technology. The selected operator name format shall apply to further read commands (+COPS?) also. <mode>=2
forces an attempt to deregister from the network. The selected mode affects to all further network registration (e.g. after
<mode>=2, MT shall be unregistered until <mode>=0 or 1 is selected). Refer subclause 9.2 for possible <err>
values. This command should be abortable when registration/deregistration attempt is made.
Read command returns the current mode, the currently selected operator and the current Access Technology. If no
operator is selected, <format>, <oper> and <AcT> are omitted.
Test command returns a set of five parameters, each representing an operator present in the network. A set consists of
an integer indicating the availability of the operator <stat>, long and short alphanumeric format of the name of the
operator, numeric format representation of the operator and access technology. Any of the formats may be unavailable
and should then be an empty field. The list of operators shall be in order: home network, networks referenced in SIM or
active application in the UICC (GSM or USIM) in the following order: HPLMN selector, User controlled PLMN
selector, Operator controlled PLMN selector and PLMN selector (in the SIM or GSM application), and other networks.
It is recommended (although optional) that after the operator list TA returns lists of supported <mode>s and
<format>s. These lists shall be delimited from the operator list by two commas.
The access technology selected parameters, <AcT>, should only be used in terminals capable to register to more than
one access technology. Selection of <AcT> does not limit the capability to cell reselections, even though an attempt is
made to select an access technology, the phone may still re-select a cell in another access technology.
Defined values
<mode>: integer type
0 automatic (<oper> field is ignored)
1 manual (<oper> field shall be present, and <AcT> optionally)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
58
3GPP TS 27.
007 version 13.3.0 Release 13
2 deregister from network
3 set only <format> (for read command +COPS?), do not attempt registration/deregistration (<oper> and
<AcT> fields are ignored); this value is not applicable in read command response
4 manual/automatic (<oper> field shall be present); if manual selection fails, automatic mode (<mode>=0) is
entered
<format>: integer type
0 long format alphanumeric <oper>
1 short format alphanumeric <oper>
2 numeric <oper>
<oper>: string type; <format> indicates if the format is alphanumeric or numeric; long alphanumeric format can
be upto 16 characters long and short format up to 8 characters (refer GSM MoU SE.13 [9]); numeric format is
the GSM Location Area Identification number (refer 3GPP TS 24.008 [8] subclause 10.5.1.3) which consists of a
three BCD digit country code coded as in ITU-T Recommendation E.212 [10] Annex A, plus a two BCD digit
network code, which is administration specific; returned <oper> shall not be in BCD format, but in IRA
characters converted from BCD; hence the number has structure: (country code digit 3)(country code digit
2)(country code digit 1)(network code digit 3)(network code digit 2)(network code digit 1)
<stat>: integer type
0 unknown
1 available
2 current
3 forbidden
<AcT>: integer type; access technology selected
0 GSM
1 GSM Compact
2 UTRAN
3 GSM w/EGPRS (see NOTE 1)
4 UTRAN w/HSDPA (see NOTE 2)
5 UTRAN w/HSUPA (see NOTE 2)
6 UTRAN w/HSDPA and HSUPA (see NOTE 2)
7 E-UTRAN
NOTE 1: 3GPP TS 44.060 [71] specifies the System Information messages which give the information about
whether the serving cell supports EGPRS.
NOTE 2: 3GPP TS 25.331 [74] specifies the System Information blocks which give the information about whether
the serving cell supports HSDPA or HSUPA.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
59
3GPP TS 27.007 version 13.3.0 Release 13
7.4 Facility lock +CLCK
Table 37: +CLCK action command syntax
Command
Possible response(s)
+CLCK=<fac>,<mode>[,<passwd>[
,<class>]] +CME ERROR: <err>
when <mode>=2 and command successful:
+CLCK: <status>[,<class1>
[<CR><LF>+CLCK: <status>,<class2>
[...]]
+CLCK=? +CLCK: (list of supported <fac>s)
+CME ERROR: <err>
Description
Execute command is used to lock, unlock or interrogate a MT or a network facility <fac>. Password is normally
needed to do such actions. When querying the status of a network service (<mode>=2) the response line for 'not active'
case (<status>=0) should be returned only if service is not active for any <class>. Refer subclause 9.2 for possible
<err> values. This command should be abortable when network facilities are set or interrogated.
Call barring facilities are based on GSM/UMTS supplementary services (refer 3GPP TS 22.088 [6]). The interaction of
these with other commands based on other GSM/UMTS supplementary services is described in the GSM/UMTS
standard.
Test command returns facility values supported as a compound value.
Defined values
<fac> values reserved by the present document:
"CS" CNTRL (lock CoNTRoL surface (e.g. phone keyboard))
"PS" PH-SIM (lock PHone to SIM/UICC card installed in the currently selected card slot) (MT asks
password when other than current SIM/UICC card inserted; MT may remember certain amount of
previously used cards thus not requiring password when they are inserted)
"PF" lock Phone to the very First inserted SIM/UICC card (also referred in the present document as PH-
FSIM) (MT asks password when other than the first SIM/UICC card is inserted)
"SC" SIM (lock SIM/UICC card installed in the currently selected card slot) (SIM/UICC asks password in
MT power-up and when this lock command issued)
"AO" BAOC (Barr All Outgoing Calls) (refer 3GPP TS 22.088 [6] clause 1)
"OI" BOIC (Barr Outgoing International Calls) (refer 3GPP TS 22.088 [6] clause 1)
"OX" BOIC-exHC (Barr Outgoing International Calls except to Home Country) (refer 3GPP TS 22.088 [6]
clause 1)
"AI" BAIC (Barr All Incoming Calls) (refer 3GPP TS 22.088 [6] clause 2)
"IR" BIC-Roam (Barr Incoming Calls when Roaming outside the home country) (refer 3GPP TS 22.088 [6]
clause 2)
"NT" barr incoming calls from numbers Not stored to TA memory
"NM" barr incoming calls from numbers Not stored to MT memory
"NS" barr incoming calls from numbers Not stored to SIM/UICC memory
13
ETSI
ET
SI TS 127 007 V13.3.0 (2016
-
03)
60
3GPP TS 27.007 version 13.3.0 Release 13
"NA" barr incoming calls from numbers Not stored in Any memory
"AB" All Barring services (refer 3GPP TS 22.030 [19]) (applicable only for <mode>=0)
"AG" All outGoing barring services (refer 3GPP TS 22.030 [19]) (applicable only for <mode>=0)
"AC" All inComing barring services (refer 3GPP TS 22.030 [19]) (applicable only for <mode>=0)
"FD" SIM card or active application in the UICC (GSM or USIM) fixed dialling memory feature (if PIN2
authentication has not been done during the current session, PIN2 is required as <passwd>)
"PN" Network Personalization (refer 3GPP TS 22.022 [33])
"PU" network sUbset Personalization (refer 3GPP TS 22.022 [33])
"PP" service Provider Personalization (refer 3GPP TS 22.022 [33])
"PC" Corporate Personalization (refer 3GPP TS 22.022 [33])
<mode>: integer type
0 unlock
1 lock
2 query status
<status>: integer type
0 not active
1 active
<passwd>: string type; shall be the same as password specified for the facility from the MT user interface or with
command Change Password +CPWD
<classx> is a sum of integers each representing a class of information (default 7 - voice, data and fax):
1 voice (telephony)
2 data (refers to all bearer services; with <mode>=2 this may refer only to some bearer service if TA
does not support values 16, 32, 64 and 128)
4 fax (facsimile services)
8 short message service
16 data circuit sync
32 data circuit async
64 dedicated packet access
128 dedicated PAD access
Implementation
The call barring supplementary service control is mandatory for MT supporting AT commands only and not supporting
the control through dial command D.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
61
3GPP TS 27.007 version 13.3.0 Release 13
7.5 Change password +CPWD
Table 38: +CPWD action command syntax
Command
Possible response(s)
+CPWD=<fac>,<oldpwd>,<newpwd> +CME ERROR: <err>
+CPWD=? +CPWD: list of supported (<fac>,<pwdlength>)s
+CME ERROR: <err>
Description
Action command sets a new password for the facility lock function defined by command Facility Lock +CLCK. Refer
subclause 9.2 for possible <err> values.
Test command returns a list of pairs which present the available facilities and the maximum length of their password.
Defined values
<fac>:
"P2" SIM PIN2
refer Facility Lock +CLCK for other values
<oldpwd>, <newpwd>: string type; <oldpwd> shall be the same as password specified for the facility from the
MT user interface or with command Change Password +CPWD and <newpwd> is the new password; maximum
length of password can be determined with <pwdlength>
<pwdlength>: integer type maximum length of the password for the facility
Implementation
Optional.
7.6 Calling line identification presentation +CLIP
Table 39: +CLIP parameter command syntax
Command
Possible response(s)
+CLIP=[<n>]
+CLIP? +CLIP: <n>,<m>
+CLIP=? +CLIP: (list of supported <n>s)
Description
This command refers to the supplementary service CLIP (Calling Line Identification Presentation) according to
3GPP TS 22.081 [3] and OIP (Originating Identification Presentation) according to 3GPP TS 24.607 [119] that enables
a called subscriber to get the calling line identity (CLI) of the calling party when receiving a mobile terminated call. Set
command enables or disables the presentation of the CLI at the TE. It has no effect on the execution of the
supplementary service CLIP / OIP in the network.
When <n>=1, the presentation of the calling line identity at the TE is enabled and when the calling subscriber allows,
the unsolicited result code
+CLIP: <number>,<type>[,<subaddr>,<satype>[,[<alpha>][,<CLI_validity>]]] is returned
after every RING (or +CRING: <type>; refer subclause "Cellular result codes +CRC") result code sent from TA to
TE. It is manufacturer specific if this response is used when normal voice call is answered. The unsolicited result code
+CLIP does not support numbers of the SIP URI format.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
62
3GPP TS 27.007 version 13.3.0 Release 13
When <n>=0, the presentation of the calling line identity at the TE with unsolicited result code +CLIP is disabled.
The calling line identity can also be reported in unsolicited result codes +CMCCSS<x> / +CMCCSSEND, enabled with
+CMCCS=3 (see AT command "monitor of current calls +CMCCS"). The unsolicited result codes +CMCCSS<x> /
+CMCCSSEND support numbers of the SIP URI format.Read command gives the status of <n>, and also triggers an
interrogation of the provision status of the CLIP supplementary service according to 3GPP TS 22.081 [3] and OIP
supplementary service according to 3GPP TS 24.607 [119] (given in <m>).
Read command returns the current settings.
Test command returns values supported as a compound value.
Defined values
<n>: integer type (parameter sets/shows the result code presentation status to the TE)
0 disable
1 enable
<m>: integer type (parameter shows the subscriber CLIP / OIP service status in the network).
0 CLIP / OIP not provisioned
1 CLIP / OIP provisioned
2 unknown (e.g. no network, etc.)
<number>: string type phone number of format specified by <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8)
<alpha>: optional string type alphanumeric representation of <number> corresponding to the entry found in
phonebook; used character set should be the one selected with command Select TE Character Set +CSCS
<CLI_validity>: integer type. This parameter can provide details why <number> does not contain a calling
party BCD number (refer 3GPP TS 24.008 [8] subclause 10.5.4.30).
0 CLI valid
1 CLI has been withheld by the originator (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Reject by user")
2 CLI is not available due to interworking problems or limitations of originating network (refer
3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code "Interaction with other service")
3 CLI is not available due to calling party being of type payphone (refer 3GPP TS 24.008 [8]
table 10.5.135a/3GPP TS 24.008 code "
Coin line/payphone
")
4 CLI is not available due to other reasons (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Unavailable").
When CLI is not available (<CLI_validity>=2, <CLI_validity>=3 or <CLI_validity>=4),
<number> shall be an empty string ("") and <type> value will not be significant. Nevertheless, TA may
return the recommended value 128 for <type> (TON/NPI unknown in accordance with 3GPP TS 24.008 [8]
subclause 10.5.4.7).
When CLI has been withheld by the originator, (<CLI_validity>=1) and the CLIP is provisioned with the
"override category" option (refer 3GPP TS 22.081 [3] and 3GPP TS 23.081 [40]), <number> and <type> is
provided. Otherwise, TA shall return the same setting for <number> and <type> as if the CLI was not
available.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
63
3GPP TS 27.007 version 13.3.0
Release 13
Implementation
Optional.
7.7 Calling line identification restriction +CLIR
Table 40: +CLIR parameter command syntax
Command
Possible response(s)
+CLIR=[<n>]
+CLIR? +CLIR: <n>,<m>
+CLIR=? +CLIR: (list of supported <n>s)
Description
This command refers to the supplementary service CLIR (Calling Line Identification Restriction) according to
3GPP TS 22.081 [3] and OIR (Originating Identification Restriction) according to 3GPP TS 24.607 [119] that allows a
calling subscriber to enable or disable the presentation of the calling line identity (CLI) to the called party when
originating a call.
Set command overrides the CLIR / OIR subscription (default is restricted or allowed) when temporary mode is
provisioned as a default adjustment for all following outgoing calls. This adjustment can be revoked by using the
opposite command. If this command is used by a subscriber without provision of CLIR / OIR in permanent mode the
network will act according to 3GPP TS 22.081 [3] and 3GPP TS 24.607 [119]).
Read command gives the default adjustment for all outgoing calls (given in <n>), and also triggers an interrogation of
the provision status of the CLIR / OIR service (given in <m>).
Test command returns values supported as a compound value.
NOTE: On a per call basis CLIR / OIR functionality is explained in subclauses
"ITU-T Recommendation V.250 [14] dial command D" and "Dial URI +CDU".
Defined values
<n>: integer type (parameter sets the adjustment for outgoing calls).
0 presentation indicator is used according to the subscription of the CLIR / OIR service.
1 CLIR / OIR invocation
2 CLIR / OIR suppression
<m>: integer type (parameter shows the subscriber CLIR / OIR service status in the network).
0 CLIR / OIR not provisioned
1 CLIR / OIR provisioned in permanent mode
2 unknown (e.g. no network, etc.)
3 CLIR / OIR temporary mode presentation restricted
4 CLIR / OIR temporary mode presentation allowed
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
64
3GPP TS 27.007 version 13.3.0 Release 13
7.8 Connected line identification presentation +COLP
Table 41: +COLP parameter command syntax
Command
Possible response(s)
+COLP=[<n>]
+COLP? +COLP: <n>,<m>
+COLP=? +COLP: (list of supported <n>s)
Description
This command refers to the supplementary service COLP (Connected Line Identification Presentation) according to
3GPP TS 22.081 [3] and TIP (Terminating Identification Presentation) according to 3GPP TS 24.608 [120] that enables
a calling subscriber to get the connected line identity (COL) of the called party after setting up a mobile originated call.
The command enables or disables the presentation of the COL at the TE. It has no effect on the execution of the
supplementary service COLR / TIR in the network.
When <n>=1, the presentation of the connected line identity at the TE enabled and when the called subscriber allows
the intermediate result code, +COLP: <number>,<type>[,<subaddr>,<satype> [,<alpha>]] is
returned from TA to TE before any +CR or ITU-T Recommendation V.250 [14] responses. It is manufacturer specific if
this response is used when normal voice call is established. The intermediate result code +COLP does not support
numbers of the SIP URI format.
NOTE: If the connected line identity is available in the TE after reception of the final response to the call setup,
+COLP is not returned as an intermediate result code but as an unsolicited result code.
When <n>=0, the presentation of the connected line identity at the TE is disabled.
The connected line identity can also be reported in unsolicited result codes +CMCCSS<x> / +CMCCSSEND, enabled
with +CMCCS=3 (see AT command "monitor of current calls +CMCCS"). The unsolicited result codes +CMCCSS<x> /
+CMCCSSEND support numbers of the SIP URI format.
Read command gives the status of <n>, and also triggers an interrogation of the provision status of the COLP
supplementary service according 3GPP TS 22.081 [3] and TIP supplementary service according to
3GPP TS 24.608 [120] (given in <m>).
Test command returns values supported as a compound value.
Defined values
<n>: integer type (parameter sets/shows the result code presentation status to the TE)
0 disable
1 enable
<m>: integer type (parameter shows the subscriber COLP service status in the network).
0 COLP / TIP not provisioned
1 COLP / TIP provisioned
2 unknown (e.g. no network, etc.)
<number>, <type>, <subaddr>, <satype>, <alpha>: refer +CLIP
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.
3.0 (2016
-
03)
65
3GPP TS 27.007 version 13.3.0 Release 13
7.9 Called line identification presentation +CDIP
Table 42: +CDIP parameter command syntax
Command
Possible response(s)
+CDIP=[<n>]
+CDIP? +CDIP: <n>,<m>
+CDIP=? +CDIP: (list of supported <n>s)
Description
This command related to a network service that provides "multiple called numbers (called line identifications) service"
to an MT. This command enables a called subscriber to get the called line identification of the called party when
receiving a mobile terminated call. Set command enables or disables the presentation of the called line identifications at
the TE.
When <n>=1, the presentation of the called line identification at the TE is enabled, the unsolicited result code
+CDIP: <number>,<type>[,<subaddr>,<satype>] is returned after every RING (or +CRING: <type>;
refer subclause "Cellular result codes +CRC") result code sent from TA to TE. It is manufacturer specific if this
response is used when normal voice call is answered. The unsolicited result code +CDIP does not support numbers of
the SIP URI format.
When <n>=0, the presentation of the called line identification at the TE is disabled.
The called line identification can also be reported in unsolicited result codes +CMCCSS<x> / +CMCCSSEND, enabled
with +CMCCS=3 (see AT command "monitor of current calls +CMCCS"). The unsolicited result codes +CMCCSS<x> /
+CMCCSSEND support numbers of the SIP URI format.
Read command gives the status of <n>, and also triggers an interrogation of the provision status of the "multiple called
numbers" service.
Test command returns values supported as a compound value.
Defined values
<n>: integer type (parameter sets/shows the result code presentation status to the TE)
0 disable
1 enable
<m>: integer type (parameter shows the subscriber "multiple called numbers" service status in the network)
0 "multiple called numbers service" is not provisioned
1 "multiple called numbers service" is provisioned
2 unknown (e.g. no network, etc.)
<number>: string type phone number of format specified by <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8)
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
66
3GPP TS 27.007 version 13.3.0 Release 13
7.10 Closed user group +CCUG
Table 43: +CCUG parameter command syntax
Command
Possible response(s)
+CCUG=[<n>[,<index>[,<info>]]]
+CCUG? +CCUG: <n>,<index>,<info>
+CCUG=?
Description
This command allows control of the Closed User Group supplementary service (refer 3GPP TS 22.085 [21]). Set
command enables the served subscriber to select a CUG index, to suppress the Outgoing Access (OA), and to suppress
the preferential CUG.
Set command with <n>=1 enables to control the CUG information on the air interface as a default adjustment for all
following outgoing calls. The interaction of this command with other commands based on other GSM/UMTS
supplementary services is described in the GSM/UMTS standard.
NOTE: On a per call basis CUG functionality is explained in subclause "ITU-T Recommendation V.250 [14] dial
command D".
Read command returns the current settings.
Defined values
<n>: integer type
0 disable CUG temporary mode
1 enable CUG temporary mode
<index>: integer type
0...9 CUG index
10 no index (preferred CUG taken from subscriber data)
<info>: integer type
0 no information
1 suppress OA
2 suppress preferential CUG
3 suppress OA and preferential CUG
Implementation
Optional. This command is superfluous when the command +CECUG is supported.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
67
3GPP TS 27.007 version 13.3.0 Release 13
7.11 Call forwarding number and conditions +CCFC
Table 44: +CCFC action command syntax
Command
Possible response(s)
+CCFC=<reason>,<mode>[,<
number>[,<type>[,<class>
[,<subaddr>[,<satype>[,<
time>]]]]]]
+CME ERROR: <err>
when <mode>=2 and command successful:
+CCFC: <status>,<class1>[,<number>,<type>[,<subad
dr>,<satype>[,<time>]]]
[<CR><LF>+CCFC: <status>,<class2>[,<number>,<type
>[,<subaddr>,<satype>[,<time>]]]
[...]]
+CCFC=? +CCFC: (list of supported <reason>s)
Description
This command allows control of the call forwarding supplementary service according to 3GPP TS 22.082 [4].
Registration, erasure, activation, deactivation, and status query are supported. When querying the status of a network
service (<mode>=2) the response line for 'not active' case (<status>=0) should be returned only if service is not
active for any <class>. Refer subclause 9.2 for possible <err> values.
Test command returns reason values supported as a compound value.
NOTE: This command cannot be used with URIs. For communication forwarding control with URI support see
AT command "call forwarding number and conditions with URI support +CCFCU".
Defined values
<reason>: integer type
0 unconditional
1 mobile busy
2 no reply
3 not reachable
4 all call forwarding (refer 3GPP TS 22.030 [19])
5 all conditional call forwarding (refer 3GPP TS 22.030 [19])
<mode>: integer type
0 disable
1 enable
2 query status
3 registration
4 erasure
<number>: string type phone number of forwarding address in format specified by <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7); default 145 when
dialling string includes international access code character "+", otherwise 129
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8); default 128
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
68
3GPP TS 27.007 version 13.3.0 Release 13
<classx> is a sum of integers each representing a class of information (default 7 - voice, data and fax):
1 voice (telephony)
2 data (refers to all bearer services; with <mode>=2 this may refer only to some bearer service if TA does
not support values 16, 32, 64 and 128)
4 fax (facsimile services)
8 short message service
16 data circuit sync
32 data circuit async
64 dedicated packet access
128 dedicated PAD access
<time>: integer type
1...30 when "no reply", "all call forwarding" or "all conditional call fowarding" is enabled or queried, this gives
the time in seconds to wait before call is forwarded, default value 20
<status>: integer type
0 not active
1 active
Implementation
Mandatory for MT supporting AT commands only and not supporting the control through dial command D.
7.12 Call waiting +CCWA
Table 45: +CCWA parameter command syntax
Command
Possible response(s)
+CCWA=[<n>[,<mode>[,<class>]]] +CME ERROR: <err>
when <mode>=2 and command successful
+CCWA: <status>,<class1>
[<CR><LF>+CCWA: <status>,<class2>
[...]]
+CCWA? +CCWA: <n>
+CCWA=? +CCWA: (list of supported <n>s)
Description
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
69
3GPP TS 27.007 version 13.3.0 Release 13
This command allows control of the supplementary service Call Waiting according to 3GPP TS 22.083 [5] and
Communication Waiting according to 3GPP TS 24.607 [137]. Activation, deactivation and status query are supported.
When querying the status of a network service (<mode>=2) the response line for 'not active' case (<status>=0)
should be returned only if service is not active for any <class>. Refer subclause 9.2 for possible <err> values.
Parameter <n> is used to disable/enable the presentation of an unsolicited result code
+CCWA: <number>,<type>,<class>,[<alpha>][,<CLI_validity>[,<subaddr>,<satype>[,<p
riority>]]] to the TE when call waiting service is enabled. The unsolicited result code +CCWA does not support
numbers of the SIP URI format.
The call waiting information can also be reported in unsolicited result codes +CMCCSS<x> / +CMCCSSEND, enabled
with +CMCCS=3 (see AT command "monitor of current calls +CMCCS"). The unsolicited result codes +CMCCSS<x> /
+CMCCSSEND support numbers of the SIP URI format.
Command should be abortable when network is interrogated.
Read command returns the current value of <n>.
Test command returns values supported as a compound value.
Defined values
<n>: integer type (sets/shows the result code presentation status to the TE)
0 disable
1 enable
<mode>: integer type (when <mode> parameter is not given, network is not interrogated)
0 disable
1 enable
2 query status
<classx>: is a sum of integers each representing a class of information (default 7 - voice, data and fax)
1 voice (telephony)
2 data (refers to all bearer services; with <mode>=2 this may refer only to some bearer service if TA does
not support values 16, 32, 64 and 128)
4 fax (facsimile services)
8 short message service
16 data circuit sync
32 data circuit async
64 dedicated packet access
128 dedicated PAD access
<status>: integer type
0 not active
1 active
<number>: string type phone number of calling address in format specified by <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
GF
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
70
3GP
P TS 27.007 version 13.3.0 Release 13
<alpha>: optional string type alphanumeric representation of <number> corresponding to the entry found in
phonebook; used character set should be the one selected with command Select TE Character Set +CSCS
<CLI_validity>: integer type. This parameter can provide details why <number> does not contain a calling
party BCD number (refer 3GPP TS 24.008 [8] subclause 10.5.4.30).
0 CLI valid
1 CLI has been withheld by the originator (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Reject by user")
2 CLI is not available due to interworking problems or limitations of originating network (refer
3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code "Interaction with other service")
3 CLI is not available due to calling party being of type payphone (refer 3GPP TS 24.008 [8]
table 10.5.135a/3GPP TS 24.008 code "
Coin line/payphone
")
4 CLI is not available due to other reasons (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Unavailable")
When CLI is not available (<CLI_validity>=2, <CLI_validity>=3 or <CLI_validity>=4),
<number> shall be an empty string ("") and <type> value will not be significant. Nevertheless, TA may
return the recommended value 128 for <type> ((TON/NPI unknown in accordance with 3GPP TS 24.008 [8]
subclause 10.5.4.7).
When CLI has been withheld by the originator, (<CLI_validity>=1) and the CLIP is provisioned with the
"override category" option (refer 3GPP TS 22.081 [3] and 3GPP TS 23.081 [40]), <number> and <type> is
provided. Otherwise, TA shall return the same setting for <number> and <type> as if the CLI was not
available.
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8)
<priority>: optional digit type parameter indicating that the eMLPP priority level of the incoming call. The
priority level values are as defined in eMLPP specification 3GPP TS 22.067 [54].
Implementation
Optional.
7.13 Call related supplementary services +CHLD
Table 46: +CHLD action command syntax
Command
Possible response(s)
+CHLD=<n> +CME ERROR: <err>
+CHLD=? +CHLD: (list of supported <n>s)
Description
This command allows the control of the following call related services:
- a call can be temporarily disconnected from the MT but the connection is retained by the network;
- multiparty conversation (conference calls);
- the served subscriber who has two calls (one held and the other either active or alerting) can connect the other
parties and release the served subscriber's own connection.
Calls can be put on hold, recovered, released, added to conversation, and transferred similarly as defined in
3GPP TS 22.030 [19]. Refer subclause 9.2 for possible <err> values.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
71
3GPP TS 27.007 version 13.3.0 Release 13
This is based on the supplementary services HOLD (Call Hold; refer 3GPP TS 22.083 [5] clause 2 and
3GPP TS 24.610 [135]), MPTY / CONF (MultiParty; refer 3GPP TS 22.084 [22] and Conference; refer
3GPP TS 24.605 [133]) and ECT (Explicit Call Transfer; refer 3GPP TS 22.091 [30] and 3GPP TS 24.629 [139]).
NOTE 1: In the CS-domain, Call Hold, MultiParty and Explicit Call Transfer are only applicable to teleservice 11.
Test command returns a list of operations which are supported. The call number required by some operations shall be
denoted by "x" (e.g. +CHLD: (0,1,1x,2,2x,3)).
Defined values
<n>: integer type; equals to numbers entered before SEND button in 3GPP TS 22.030 [19] subclause 6.5.5.1
NOTE 2: The "directory number" case shall be handled with dial command D, and the END case with hangup
command H (or +CHUP). The 4*"directory number" case is handled with +CTFR command.
Implementation
Optional.
7.14 Call deflection +CTFR
Table 47: +CTFR action command syntax
Command
Possible response(s)
+CTFR=<number>[,<type>[,<subaddr>[,<satype>]]] +CME ERROR: <err>
+CTFR=?
Description
This refers to a service that causes an incoming alerting call to be forwarded to a specified number. Action command
does this. Refer subclause 9.2 for possible <err> values.
This is based on the GSM/UMTS supplementary service CD (Call Deflection; refer 3GPP TS 22.072 [31]). The
interaction of this command with other commands based on other GSM/UMTS supplementary services is described in
the GSM/UMTS standards.
NOTE 1: Call Deflection is only applicable to teleservice 11.
NOTE 2: This command cannot be used with URIs. For communication forwarding control with URI support see
AT command "call forwarding number and conditions with URI support +CCFCU".
Defined values
<number>: string type phone number of format specified by <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7); default 145 when
dialling string includes international access code character "+", otherwise 129
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8); default 128
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
72
3GPP TS 27.007 version 13.3.0 Release 13
7.15 Unstructured supplementary service data +CUSD
Table 48: +CUSD parameter command syntax
Command
Possible response(s)
+CUSD=[<n>[,<str>[,<dcs>]]] +CME ERROR: <err>
+CUSD? +CUSD: <n>
+CUSD=? +CUSD: (list of supported <n>s)
Description
This command allows control of the Unstructured Supplementary Service Data (USSD) according to
3GPP TS 22.090 [23], 3GPP TS 24.090 [148] and 3GPP TS 24.390 [131]. Both network and mobile initiated operations
are supported. Parameter <n> is used to disable/enable the presentation of an unsolicited result code. The value <n>=2
is used to cancel an ongoing USSD session. For an USSD response from the network, or a network initiated operation,
the format is: +CUSD: <m>[,<str>,<dcs>].
NOTE 1: If the MT supports USSD according to 3GPP TS 24.090 [148] and USSD according to
3GPP TS 24.390 [131] then the MT decides which to invoke. The decision is out of scope of this
specification.
When <str> is given, a mobile initiated USSD-string or a response USSD-string to a network initiated operation is
sent to the network. The response USSD-string from the network is returned in a subsequent unsolicited +CUSD result
code. Refer subclause 9.2 for possible <err> values.
NOTE 2: In case of successful mobile initiated operation, TA implemented according to a version prior to 6 of this
standard, waits the USSD response from the network and sends it to the TE before the final result code.
This will block the AT command interface for the period of the operation. Such TA does not support <n>
value 2.
The interaction of this command with other commands based on other GSM/UMTS supplementary services is described
in the GSM/UMTS standards.
Read command returns the current value of <n>.
Test command returns values supported as a compound value.
Defined values
<n>: integer type (sets/shows the result code presentation status to the TE)
0 disable the result code presentation to the TE
1 enable the result code presentation to the TE
2 cancel session (not applicable to read command response)
<str>: string type USSD-string (when <str> parameter is not given, network is not interrogated):
- if <dcs> indicates that 3GPP TS 23.038 [25] 7 bit default alphabet is used:
- if TE character set other than "HEX" (refer command Select TE Character Set +CSCS): MT/TA converts
GSM alphabet into current TE character set according to rules of 3GPP TS 27.005 [24] Annex A
- if TE character set is "HEX": MT/TA converts each 7-bit character of GSM alphabet into two IRA
character long hexadecimal number (e.g. character Π (GSM 23) is presented as 17 (IRA 49 and 55))
- if <dcs> indicates that 8-bit data coding scheme is used: MT/TA converts each 8-bit octet into two IRA
character long hexadecimal number (e.g. octet with integer value 42 is presented to TE as two characters 2A
(IRA 50 and 65))
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
73
3GPP TS 27.007 version 13.3.0 Release 13
- if <dcs> indicates that 16-bit data coding scheme (UCS2) is used: MT/TA splits the 16 bits into two 8-bit
octets. Each of those octets are converted as per the 8-bit data coding scheme, with the most significant octet
first (e.g. decimal value 4906 is presented to TE as four characters 132A (IRA 49, 51, 50 and 65))
<dcs>: integer type (shows Cell Broadcast Data Coding Scheme, see 3GPP TS 23.038 [25]). Default value is 0.
<m>: integer type (shows the USSD response from the network or the network initiated operation)
0 no further user action required (network initiated USSD-Notify, or no further information needed after
mobile initiated operation)
1 further user action required (network initiated USSD-Request, or further information needed after mobile
initiated operation)
2 USSD terminated by network
3 other local client has responded
4 operation not supported
5 network time out
Implementation
Optional.
7.16 Advice of charge +CAOC
Table 49: +CAOC parameter command syntax
Command
Possible response(s)
+CAOC[=<mode>] [+CAOC: <ccm>]
+CME ERROR: <err>
+CAOC? +CAOC: <mode>
+CAOC=? +CAOC: (list of supported <mode>s)
Description
This refers to Advice of Charge supplementary service (3GPP TS 22.024 [26] and 3GPP TS 22.086 [27]) that enables
subscriber to get information about the cost of calls. With <mode>=0, the execute command returns the current call
meter value from the MT.
The command also includes the possibility to enable/disable reporting of the CCM information with unsolicited result
code +CCCM: <ccm>. When enabled, this unsolicited result code is sent when the CCM value changes, but not more
frequently than at every 10 seconds.
Refer subclause 9.2 for possible <err> values.
NOTE: Advice of Charge values stored in the SIM card or in the active application in the UICC (GSM or USIM)
(ACM, ACMmax, PUCT) can be accessed with generic or restricted SIM access command (+CSIM or
+CRSM)).Those values can be more readily accessed with commands +CACM, +CAMM and +CPUC.
Read command indicates whether the unsolicited reporting is activated or not.
Test command returns the supported mode values as a compound value.
Defined values
<mode>: integer type
0 query CCM value
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
74
3GPP TS 27.007 version 13.3.0 Release 13
1 deactivate the unsolicited reporting of CCM value
2 activate the unsolicited reporting of CCM value
<ccm>: string type; three bytes of the current call meter value in hexadecimal format (e.g. "00001E" indicates
decimal value 30); value is in home units and bytes are similarly coded as ACMmax value in the SIM card or in
the active application in the UICC (GSM or USIM)
Implementation
Optional.
7.17 Supplementary service notifications +CSSN
Table 50: +CSSN parameter command syntax
Command
Possible response(s)
+CSSN=[<n>[,<m>]]
+CSSN? +CSSN: <n>,<m>
+CSSN=? +CSSN: (list of supported <n>s),(list of supported <m>s)
Description
This command refers to supplementary service related network initiated notifications. The set command
enables/disables the presentation of notification result codes from TA to TE.
When <n>=1 and a supplementary service notification is received after a mobile originated call setup, intermediate
result code +CSSI: <code1>[,[<index>][,<SS_code>]] is sent to TE before any other MO call setup result
codes presented in the present document or in ITU-T Recommendation V.250 [14]. When several different <code1>s
are received from the network, each of them shall have its own +CSSI result code.
NOTE: If the supplemenary service notification is available in the TE after reception of the final response to the
call setup, +CSSI is not returned as an intermediate result code but as an unsolicited result code.
When <m>=1 and a supplementary service notification is received during a mobile terminated call setup or during a
call, or when a forward check supplementary service notification is received, unsolicited result code
+CSSU: <code2>[,<index>[,[<number>],[<type>][,[<subaddr>],[<satype>]][,<SS_code>
]]] is sent to TE. In case of MT call setup, result code is sent after every +CLIP result code (refer command "Calling
line identification presentation +CLIP") and when several different <code2>s are received from the network, each of
them shall have its own +CSSU result code. <code2>=5 does not reflect any supplementary service, and the parameter
<SS_code> will not be provided.
The supplementary service notification can also be reported in unsolicited result codes +CMCCSS<x> / +CMCCSSEND,
enabled with +CMCCS=3 (see AT command "monitor of current calls +CMCCS"). The unsolicited result codes
+CMCCSS<x> / +CMCCSSEND support numbers of the SIP URI format.
Read command returns the current settings.
Test command returns values supported as a compound value.
Defined values
<n>: integer type (parameter sets/shows the +CSSI intermediate result code presentation status to the TE)
0 disable
1 enable
<m>: integer type (parameter sets/shows the +CSSU unsolicited result code presentation status to the TE)
0 disable
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
75
3GPP TS 27.007 versio
n 13.3.0 Release 13
1 enable
<code1>: integer type (it is manufacturer specific, which of these codes are supported)
0 unconditional call forwarding is active
1 some of the conditional call forwardings are active
2 call has been forwarded
3 call is waiting
4 this is a CUG call (also <index> present)
5 outgoing calls are barred
6 incoming calls are barred
7 CLIR suppression rejected
8 call has been deflected
<index>: integer type (refer Closed user group +CCUG command)
<SS_code>: integer type used to present the code identifying a single supplementary service (see
3GPP TS 24.080 [109] and 3GPP TS 29.002 [110] subclause 17.7.5)
<code2>: integer type (it is manufacturer specific, which of these codes are supported)
0 this is a forwarded call (MT call setup)
1 this is a CUG call (also <index> present) (MT call setup)
2 call has been put on hold (during a voice call)
3 call has been retrieved (during a voice call)
4 multiparty call entered (during a voice call)
5 call on hold has been released (this is not a SS notification) (during a voice call)
6 forward check SS message received (can be received whenever)
7 call is being connected (alerting) with the remote party in alerting state in explicit call transfer operation
(during a voice call)
8 call has been connected with the other remote party in explicit call transfer operation (also number and
subaddress parameters may be present) (during a voice call or MT call setup)
9 this is a deflected call (MT call setup)
10 additional incoming call forwarded
<number>: string type phone number of format specified by <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8)
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
76
3GPP TS 27.007 version 13.3.0 Release 13
7.18 List current calls +CLCC
Table 51: +CLCC action command syntax
Command
Possible response(s)
+CLCC [+CLCC: <ccid1>,<dir>,<stat>,<mode>,<mpty>[,<number>
,<type>[,<alpha>[,<priority>[,<CLI validity>]]]]
[<CR><LF>+CLCC: <ccid2>,<dir>,<stat>,<mode>,<mpty>[,
<number>,<type>[,<alpha>[,<priority>[,<CLI validity>
]]]]
[...]]]
+CME ERROR: <err>
+CLCC=?
Description
Returns list of current calls of MT. If command succeeds but no calls are available, no information response is sent to
TE. Refer subclause 9.2 for possible <err> values. See also AT command +CLCCS.
Defined values
<ccidx>: integer type. Call identification number as described in 3GPP TS 22.030 [19] subclause 6.5.5.1. This
number can be used in +CHLD command operations. Value range is from 1 to N. N, the maximum number of
simultaneous call control processes is implementation specific.
<dir>: integer type
0 mobile originated (MO) call
1 mobile terminated (MT) call
<stat>: integer type (state of the call)
0 active
1 held
2 dialing (MO call)
3 alerting (MO call)
4 incoming (MT call)
5 waiting (MT call)
<mode>: integer type (bearer/teleservice)
0 voice
1 data
2 fax
3 voice followed by data, voice mode
4 alternating voice/data, voice mode
5 alternating voice/fax, voice mode
6 voice followed by data, data mode
7 alternating voice/data, data mode
ETSI
ETSI TS 127
007 V13.3.0 (2016
-
03)
77
3GPP TS 27.007 version 13.3.0 Release 13
8 alternating voice/fax, fax mode
9 unknown
<mpty>: integer type
0 call is not one of multiparty (conference) call parties
1 call is one of multiparty (conference) call parties
<number>: string type phone number in format specified by <type>.
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7).
<alpha>: string type alphanumeric representation of <number> corresponding to the entry found in phonebook;
used character set should be the one selected with command Select TE Character Set +CSCS.
<priority>: integer type parameter indicating the eMLPP priority level of the call, values specified in
3GPP TS 22.067 [54].
<CLI validity>: integer type. This parameter can provide details why <number> does not contain a calling
party BCD number (refer 3GPP TS 24.008 [8] subclause 10.5.4.30). The parameter is not present for MO call
types.
0 CLI valid
1 CLI has been withheld by the originator (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Reject by user")
2 CLI is not available due to interworking problems or limitations of originating network (refer
3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code "Interaction with other service")
3 CLI is not available due to calling party being of type payphone (refer 3GPP TS 24.008 [8]
table 10.5.135a/3GPP TS 24.008 code "
Coin line/payphone
")
4 CLI is not available due to other reasons (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Unavailable")
When CLI is not available (<CLI validity>=2, <CLI validity>=3 or <CLI validity>=4),
<number> shall be an empty string ("") and <type> value will not be significant. Nevertheless, TA may
return the recommended value 128 for <type> (TON/NPI unknown in accordance with 3GPP TS 24.008 [8]
subclause 10.5.4.7).
When CLI has been withheld by the originator, (<CLI validity>=1) and the CLIP is provisioned with the
"override category" option (refer 3GPP TS 22.081 [3] and 3GPP TS 23.081 [40]), <number> and <type> is
provided. Otherwise, TA shall return the same setting for <number> and <type> as if the CLI was not
available.
Implementation
Optional. Recommended when +CHLD command is implemented.
When +CDU is supported and SIP URIs are used in the MT, the AT command +CLCC is fully replaced by +CLCCS.
7.19 Preferred PLMN list +CPOL
Table 52: +CPOL parameter command syntax
Command
Possible response(s)
+CPOL=[<index>][,<for
mat>[,<oper>[,<GSM_Ac
T>,<GSM_Compact_AcT>,
<UTRAN_AcT>,<E-
UTRAN_AcT>]]]
+CME ERROR: <err>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
78
3GPP TS 27.007 version 13.3.0 Release 13
+CPOL? +CPOL: <index1>,<format>,<oper1>[,<GSM_AcT1>,<
GSM_Compact_AcT1>,<UTRAN_AcT1>,<E-UTRAN_AcT1>]
[<CR><LF>+CPOL: <index2>,<format>,<oper2>[,<GS
M_AcT2>,<GSM_Compact_AcT2>,<UTRAN_AcT2>,<E-
UTRAN_AcT2>]
[...]]
+CME ERROR: <err>
+CPOL=? +CPOL: (list of supported <index>s),(list of supported
<format>s)
+CME ERROR: <err>
Description
This command is used to edit the PLMN selector with Access Technology lists in the SIM card or active application in
the UICC (GSM or USIM).
Execute command writes an entry in the SIM/USIM list of preferred PLMNs, previously selected by the command
+CPLS. If no list has been previously selected, the User controlled PLMN selector with Access Technology,
EF
PLMNwAcT,
is the one accessed by default. If <index> is given but <oper> is left out, entry is deleted. If <oper> is
given but <index> is left out, <oper> is put in the next free location. If only <format> is given, the format of the
<oper> in the read command is changed. The Access Technology selection parameters, <GSM_AcT>,
<GSM_Compact_AcT> and <UTRAN_AcT> and <E-UTRAN_AcT> are required when writing User controlled
PLMN selector with Access Technology, EF
PLMNwAcT
, Operator controlled PLMN selector with Access Technology
EF
OPLMNwAcT
and HPLMN selector with Access Technology EF
HPLMNwAcT
, see 3GPP TS 31.102 [59]. Refer
subclause 9.2 for possible <err> values.
NOTE 1: MT can also update the User controlled PLMN selector with Access Technology, EF
PLMNwAcT
,
automatically when new networks are selected.
NOTE 2: The Operator controlled PLMN selector with Access Technology EF
OPLMNwAcT
, can only be written if the
write access condition in the SIM/USIM has been previously verified.
Read command returns all used entries from the SIM/USIM list of preferred PLMNs, previously selected by the
command +CPLS, with the Access Technologies for each PLMN in the list.
Test command returns the whole index range supported by the SIM as compound values.
Defined values
<indexn>: integer type; the order number of operator in the SIM/USIM preferred operator list
<format>: integer type
0 long format alphanumeric <oper>
1 short format alphanumeric <oper>
2 numeric <oper>
<opern>: string type; <format> indicates if the format is alphanumeric or numeric (see +COPS)
<GSM_AcTn>: integer type; GSM access technology:
0 access technology not selected
1 access technology selected
<GSM_Compact_AcTn>: integer type; GSM compact access technology
0 access technology not selected
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
79
3GPP TS 27.007 version 13.3.0 Release 13
1 access technology selected
<UTRAN_AcTn>: integer type; UTRAN access technology
0 access technology not selected
1 access technology selected
<E-UTRAN_AcTn>: integer type; E-UTRAN access technology
0 access technology not selected
1 access technology selected
Implementation
Optional.
7.20 Selection of preferred PLMN list +CPLS
Table 53: +CPLS parameter command syntax
Command
Possible response(s)
+CPLS=[<list>] +CME ERROR: <err>
+CPLS? +CPLS: <list>
+CME ERROR: <err>
+CPLS=? +CPLS: (list of supported <list>s)
+CME ERROR: <err>
Description
This command is used to select one PLMN selector with Access Technology list in the SIM card or active application in
the UICC (GSM or USIM), that is used by +CPOL command.
Execute command selects a list in the SIM/USIM. Refer subclause 9.2 for possible <err> values.
Read command returns the selected PLMN selector list from the SIM/USIM.
Test command returns the whole index range supported lists by the SIM/USIM as a compound value.
Defined values
<list>: integer type
0 User controlled PLMN selector with Access Technology EF
PLMNwAcT
, if not found in the SIM/UICC then
PLMN preferred list EF
PLMNsel
(this file is only available in SIM card or GSM application selected in UICC)
1 Operator controlled PLMN selector with Access Technology EF
OPLMNwAcT
2 HPLMN selector with Access Technology EF
HPLMNwAcT
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
80
3GPP TS 27.007 version 13.3.0 Release 1
3
7.21 Read operator names +COPN
Table 54: +COPN action command syntax
Command
Possible response(s)
+COPN +COPN: <numeric1>,<alpha1>
[<CR><LF>+COPN: <numeric2>,<alpha2>
[...]]
+CME ERROR: <err>
+COPN=?
Description
Execute command returns the list of operator names from the MT. Each operator code <numericn> that has an
alphanumeric equivalent <alphan> in the MT memory shall be returned. Refer subclause 9.2 for possible <err>
values.
Defined values
<numericn>: string type; operator in numeric format (see +COPS)
<alphan>: string type; operator in long alphanumeric format (see +COPS)
Implementation
Optional.
7.22 eMLPP priority registration and interrogation +CAEMLPP
Table 55: +CAEMLPP parameter command syntax
Command
Possible Response(s)
+CAEMLPP=<priority> +CM
E
ERROR: <err>
+CAEMLPP? +CAEMLPP: <default_priority>,<max_priority>
+CME ERROR: <err>
+CAEMLPP=?
Description
The execute command is used to change the default priority level of the user in the network. The requested priority level
is checked against the eMLPP subscription of the user stored on the SIM card or in the active application in the UICC
(GSM or USIM) EF
eMLPP
. If the user doesn't have subscription for the requested priority level an ERROR or
+CMEE ERROR result code is returned. Refer subclause 9.2 for possible <err> values.
The read command triggers an interrogation of the provision of the maximum priority level which the service subscriber
is allowed to use and default priority level activated by the user.
If the service is not provisioned, a result code including the SS-Status (?) parameter is returned.
Defined Values
<priority>: integer type parameter which identifies the default priority level to be activated in the network,
values specified in 3GPP TS 22.067 [54]
<default_priority>: integer type parameter which identifies the default priority level which is activated in
the network, values specified in 3GPP TS 22.067 [54]
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
81
3GPP TS 27.007 version 13.3.0 Release 13
<max_priority>: integer type parameter which identifies the maximum priority level for which the service
subscriber has a subscription in the network, values specified in 3GPP TS 22.067 [54]
Implementation
Mandatory for a MT supporting AT commands only and supplemantery service eMLPP is implemented.
7.23 eMLPP subscriptions +CPPS
Table 56: +CPPS action command syntax
Command
Possible response(s)
+CPPS [+CPPS: <priority>[,<priority>
[...]]]
+CME ERROR: <err>
+CPPS=?
Description
This command returns all eMLPP priority subscriptions of the user stored on the SIM card or in the active application in
the UICC (GSM or USIM) EF
eMLPP
. If no explicit priority level subscription is stored on the SIM card or in the active
application in the UICC (GSM or USIM) EF
eMLPP
the result code OK is returned. Refer subclause 9.2 for possible
<err> values.
Defined values
<priority>: integer type, eMLPP subscription to priority level {0,1,..,4} as defined in 3GPP TS 22.067 [54].
Implementation
Mandatory for a MT supporting AT commands only and eMLPP is implemented.
7.24 Fast call setup conditions +CFCS
Table 57: +CFCS parameter command syntax
Command
Possible response(s)
+CFCS=<priority>,<status> +CME ERROR: <err>
+CFCS? [+CFCS: <priority>[,<priority>
[...]]]
+CME ERROR: <err>
+CFCS=?
+CFCS: (list of supported
<priority>,<status>s)
Description
The set command is used to edit the status of the priority level for fast call set-up stored on the SIM card or in the active
application in the UICC (GSM or USIM) EF
eMLPP
. If the user has no subscription to the priority level status he wants to
edit, an ERROR or +CME ERROR result code is returned. Refer subclause 9.2 for possible <err> values.
The read command returns all enabled priority levels for fast call set-up stored on the SIM card or in the active
application in the UICC (GSM or USIM) EF
eMLPP
. If no priority level is enabled for fast call set-up, the result code OK
is returned.
Test command returns the values supported by the UE.
Defined values
<priority>: integer type, eMLPP fast call set-up priority level {0,1,..,4} as defined in 3GPP TS 22.067 [54]
<status>: integer type
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
82
3GPP TS 27.007 version 13.3.0 Release 13
0 disable <priority> for fast call set-up
1 enable <priority> for fast call set-up
Implementation
Mandatory for a MT supporting AT commands only and eMLPP is implemented.
7.25 Automatic answer for eMLPP service +CAAP
Table 58: +CAAP parameter command syntax
Command
Possible response(s)
+CAAP=<priority>,<status> +CME ERROR: <err>
+CAAP? [+CAAP: <priority>[,<priority>
[...]]]
+CME ERROR: <err>
+CAAP=?
+CAAP: (list of supported
<priority>,<status>s)
Description
The set command is used to edit the status of the priority level for automatic answering for eMLPP stored on the SIM
card or in the active application in the UICC (GSM or USIM) EF
AAeM
. If the user has no subscription to the priority
level status he wants to edit, an ERROR or +CME ERROR result code is returned. Refer subclause 9.2 for possible
<err> values.
The read command returns all enabled priority levels for automatic answering for eMLPP stored on the SIM card or in
the active application in the UICC (GSM or USIM) EF
AAeM
. If no priority level is enabled for automatic answering for
eMLPP, the result code OK is returned.
Test command returns the values supported by the UE.
Defined values
<priority>: eMLPP automatic answer priority level value {A,B,0,1,..,4} as defined in 3GPP TS 22.067 [54]
<status>: integer type
0 disable eMLPP <priority> for automatic answering
1 enable eMLPP <priority> for automatic answering
Implementation
Mandatory for a MT supporting AT commands only and eMLPP is implemented.
7.26 User to user signalling service 1 +CUUS1
Table 59: +CUUS1 parameter command syntax
Command
Possible response(s)
+CUUS1=[<n>[,<m>[,<message>[,<UUIE>
[,<message>[,<UUIE>[,...]]]]]]] +CME ERROR: <err>
+CUUS1? +CUUS1: <n>,<m>[,<message>,<UUIE>[,<mes
sage>,<UUIE>[,...]]]
+CUUS1=? +CUUS1: (list of supported <n>s),(list of supported
<m>s),(list of supported <message>s),(list of
supported <messageI>s),(list of supported
<messageU>s)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
83
3GPP TS 27.007 version 13.3.0 Release 13
Description
This command allows control of the User-to-User Signalling Supplementary Service 1 (UUS1) according to
3GPP TS 22.087 [58].
Parameters <message> and <UUIE> are used to activate/deactivate the implicit request of the User-to-User
Signalling Supplementary Service 1.
When <message> and <UUIE> are both present the string specified in <UUIE> is included as the value part of the
User-to-User Information Element (as defined in 3GPP TS 24.008 [8]) into all subsequent messages of type
<message>. If parameter <message> is present but parameter <UUIE> is not present then the User-to-User
Information Element shall not be present in subsequent messages of type <message>.
Parameters <n> and <m> are used to enable/disable the presentation of incoming User-to-User Information Elements.
When <n> = 1 and a User-to-User Information is received after a mobile originated call setup or after hanging up a call,
intermediate result code +CUUS1I: <messageI>,<UUIE> is sent to the TE.
When <m> = 1 and a User-to-User Information is received during a mobile terminated call setup or during a remote
party call hangup, unsolicited result code +CUUS1U: <messageU>,<UUIE> is sent to the TE.
Refer subclause 9.2 for possible <err> values.
Test command returns values supported as compound values.
Defined values
<n>: integer type (parameter sets/shows the +CUUS1I result code presentation status in the TA)
0 disable.
1 enable.
<m>: integer type (parameter sets/shows the +CUUS1U result code presentation status in the TA)
0 disable.
1 enable.
<message>: integer type (type of message containing the outgoing User-to-User Information Element)
0 ANY
1 SETUP
2 ALERT
3 CONNECT
4 DISCONNECT
5 RELEASE
6 RELEASE_COMPLETE
<messageI>: integer type (type of message containing the intermediate User-to-User Information Element)
0 ANY
1 ALERT
2 PROGRESS
3 CONNECT (sent after +COLP if enabled)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
84
3GPP TS 27.007 version 13.3.0 Release 13
4 RELEASE
<messageU>: integer type (type of message containing the unsollicited User-to-User Information Element)
0 ANY
1 SETUP (returned after +CLIP if presented, otherwise after every RING or +CRING)
2 DISCONNECT
3 RELEASE_COMPLETE
<UUIE>: the User-user Information Element (as defined in 3GPP TS 24.008 [8]) in hexadecimal character format
(for hexadecimal format, refer +CSCS).
NOTE: If the TA does not distinguish the type of message containing the User-to-user Information Element, it
can use the value for ANY message.
Implementation
Optional.
7.27 Preferred network indication +CPNET
Table 59A: +CPNET parameter command syntax
Command
Possible response(s)
+CPNET=[<Pref_net>]
+CPNET? +CPNET: <Pref_net>
+CPNET=? +CPNET: (list of supported <Pref_net>s)
Description
This command indicates whether the terminal has preference <Pref_net> for GERAN/UTRAN/E-UTRAN or
GAN, see 3GPP TS 44.318 [70].
Read command returns the current preference for GERAN/UTRAN/E-UTRAN or GAN.
Test command returns the parameter indicating preference <Pref_net> for GERAN/UTRAN/E-UTRAN or GAN as
a compound value.
Defined values
<Pref_net>: integer type; indicates the preference for GERAN/UTRAN/E-UTRAN or GAN.
0 GERAN/UTRAN/E-UTRAN shall be used. The terminal uses GERAN/UTRAN/E-UTRAN coverage only.
1 GAN shall be used. The terminal used GAN coverage only.
2 GERAN/UTRAN/E-UTRAN preferred. The terminal prefers to stay in GERAN/UTRAN/E-UTRAN rather
than GAN.
3 GAN preferred. The terminal prefers to stay in GAN rather than GERAN/UTRAN/E-UTRAN.
NOTE: Usage of value 0 or 1 will prevent the terminal from changing between GERAN/UTRAN/E-UTRAN and
GAN. E.g. setting <Pref_net> to 1 indicates that only GAN will be used, and prevents the terminal
from using available GERAN/UTRAN/E-UTRAN coverage.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
85
3GPP TS 27.007 version 13.3.0 Release 13
7.28 Preferred network status +CPNSTAT
Table 59B: +CPNSTAT parameter command syntax
Command
Possible response(s)
+CPNSTAT=[<n>]
+CPNSTAT? +CPNSTAT: <n>,<stat>
+CPNSTAT=? +CPNSTAT: (list of supported <n>s)
Description
Set command controls the presentation of an unsolicited result code +CPNSTAT: <stat> when <n>=1 and there is a
change in the preferred network indication status.
Read command returns the status of result code presentation <n> and an integer <stat> which shows whether the
terminal is in GERAN/UTRAN/E-UTRAN or GAN, see 3GPP TS 44.318 [70].
NOTE: Further details about registration status are available using commands +CREG (see subclause 7.2),
+CGREG (see subclause 10.1.19) and +CEREG (see subclause 10.1.21).
Test command returns the list of supported unsolicited result codes as a compound value.
Defined values
<n>: integer type
0 disable preferred network indication unsolicited result code.
1 enable preferred network indication unsolicited result code +CPNSTAT: <stat>.
<stat>: integer type; preferred network indication status.
0 Requested network not available.
1 GERAN/UTRAN/E-UTRAN used.
2 GAN used.
Implementation
Optional.
7.29 Current packet switched bearer +CPSB
Table 59C: +CPSB parameter command syntax
Command
Possible response(s)
+CPSB=[<n>] +CME ERROR: <err>
+CPSB? +CPSB: <n>[,<cid>,<curr_bearer>]
[<CR><LF>+CPSB: <n>,<cid>,<curr_bearer>
[...]]
+CME ERROR: <err>
+CPSB=? +CPSB: (list of supported <n>s)
Description
Set command controls the presentation of an unsolicited result code +CPSB: <cid>,<curr_bearer> when
<n>=1 and the <cid> corresponds to a PDP context in the PDP-ACTIVE state or to an EPS bearer context and there is
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
86
3GPP TS 27.007 version 13.3.0 Release 13
a change in the current bearer due to the reception of a control or signalling message from the network as specified in
3GPP TS 44.060 [71], 3GPP TS 25.331 [74] or 3GPP TS 36.331 [86].
Read command returns the current status of unsolicited result code presentation <n>. The parameters <cid> and
<curr_bearer> are returned for each defined context when <n>=1 for <cid>s that correspond to a PDP context in
the PDP-ACTIVE state or to an EPS bearer context.
Refer subclause 9.2 for possible <err> values.
Test command returns the list of supported <n>s as a compound value.
Defined values
<n>: integer type
0 disable the presentation of the unsolicited result code
1 enable the presentation of the unsolicited result code
+CPSB: <cid>,<curr_bearer>
<cid>: A numeric parameter which specifies a particular PDP context or EPS bearer context definition. The
<cid> parameter is local to the TE-MT interface and identifies only those PDP or EPS bearer contexts which
have been setup via AT command (see the +CGDCONT and +CGDSCONT commands).
<curr_bearer>: integer type; the current packet switched bearer which is established between the UE and
network.
0 There is currently no packet switched bearer between the UE and the network (e.g. RAB is released in UMTS
or the TBF is released in GSM). This would mean that there is no bearer associated to the PDP context
referred to by the <cid> parameter and hence no data transfer is currently occuring on that particular PDP
context. This result code covers the case where the PDP context is active but there is no bearer associated
with it.
1 GPRS. (See 3GPP TS 44.060 [71] for definition of GPRS TBF Mode)
2 EGPRS. (See 3GPP TS 44.060 [71] for definition of EGPRS TBF Mode)
3 Non-HSUPA in uplink and non-HSDPA in downlink. (See NOTE 1 to NOTE 3)
4 HSUPA in uplink and non-HSDPA in downlink. (See NOTE 1 to NOTE 4)
5 Non-HSUPA in uplink and HSDPA in downlink. (See NOTE 1 to NOTE 4)
6 HSUPA in uplink and HSDPA in downlink. (See NOTE 1 to NOTE 4)
7 EPS (See NOTE 5)
NOTE 1: The term "non-HSDPA" means a non-HSDPA UMTS bearer. 3GPP TS 25.331 [74] specifies the criterion
to be satisfied in order for a downlink UMTS RAB to be termed as HSDPA. If those criterion are not met,
then the downlink UMTS RAB would be termed as "non-HSDPA" by this AT command.
NOTE 2: The term "non-HSUPA" means a non-HSUPA UMTS bearer. 3GPP TS 25.331 [74] specifies the criterion
to be satisfied in order for an uplink UMTS RAB to be termed as HSUPA (or Enhanced uplink DCH). If
those criterion are not met, then the uplink UMTS RAB would be termed as "non-HSUPA" by this AT
command.
NOTE 3: The terms "non-HSDPA", "non-HSUPA" indicate R99 to pre- HSDPA or pre-HSUPA UMTS bearers.
They do not imply GPRS or EGPRS bearers.
NOTE 4: See 3GPP TS 25.308 [72] for HSDPA and 3GPP TS 25.319 [73] for HSUPA.
NOTE 5: The term "EPS" means an EPS bearer (see 3GPP TS 36.331 [86]).
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
87
3GPP TS 27.00
7 version 13.3.0 Release 13
7.30 Calling name identification presentation +CNAP
Table 59D: +CNAP parameter command syntax
Command
Possible response(s)
+CNAP=[<n>]
+CNAP? +CNAP: <n>,<m>
+CNAP=? +CNAP: (list of supported <n>s)
Description
This command refers to the supplementary service CNAP (Calling Name Presentation) according to
3GPP TS 22.096 [93] that enables a called subscriber to get a calling name indication (CNI) of the calling party when
receiving a mobile terminated call. Set command enables or disables the presentation of the CNI at the TE. It has no
effect on the execution of the supplementary service CNAP in the network.
When <n>=1, the presentation of the calling name indication at the TE is enabled and CNI is provided the unsolicited
result code, +CNAP: <name>[,<CNI_validity>] is returned after every RING (or +CRING: <type>; refer
subclause "Cellular result codes +CRC") result code sent from TA to TE. It is manufacturer specific if this response is
used when normal voice call is answered.
The calling name indication can also be reported in unsolicited result codes +CMCCSS<x> / +CMCCSSEND, enabled
with +CMCCS=3 (see AT command "monitor of current calls +CMCCS"). The unsolicited result codes +CMCCSS<x> /
+CMCCSSEND support numbers of the SIP URI format.
Read command gives the status of <n>, and also triggers an interrogation of the provision status of the CNAP service
according 3GPP TS 22.096 [93] (given in <m>).
Test command returns values supported as a compound value.
Defined values
<n>: integer type (parameter sets/shows the result code presentation status to the TE)
0 disable
1 enable
<m>: integer type (parameter shows the subscriber CNAP service status in the network)
0 CNAP not provisioned
1 CNAP provisioned
2 unknown (e.g. no network, etc.)
<name>: string type, up to 80 characters long string containing the calling name
<CNI_validity>: integer type
0 CNI valid
1 CNI has been withheld by the originator.
2 CNI is not available due to interworking problems or limitations of originating network.
When CNI is not available ( <CNI_validity>=2), <name> shall be an empty string ("").
When CNI has been withheld by the originator, (<CNI_validity>=1) and the CNAP is provisioned with the
"override category" option (refer 3GPP TS 22.096 [93] and 3GPP TS 23.096 [94]), <name> is provided.
Otherwise, TA shall return the same setting for <name> as if the CNI was not available.
Implementation
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
88
3GPP TS 27.007 version 13.3.0 Release 13
Optional.
7.31 Connected line identification restriction status +COLR
Table 59E: +COLR action command syntax
Command
Possible response(s)
+COLR +COLR: <m>
+COLR=?
Description
This command refers to the supplementary service COLR (Connected Line Identification Restriction) according to
3GPP TS 22.081 [3] and supplementary service TIR (Terminating Identification Restriction) according to
3GPP TS 24.608 [120] that enables a called subscriber to restrict the possibility of presentation of connected line
identity (COL) to the calling party after receiving a mobile terminated call. The command displays the status of the
COL presentation in the network. It has no effect on the execution of the supplementary services COLR / TIR in the
network.
The command triggers an interrogation of the activation status of the COLR supplementary service according to
3GPP TS 22.081 [3] and the TIR supplementary service according to 3GPP TS 24.608 [120] (given in <m>).
Activation, deactivation, registration and erasure of the supplementary service COLR / TIR are not applicable.
Defined values
<m>: integer type (parameter shows the subscriber COLR / TIR service status in the network).
0 COLR / TIR not provisioned
1 COLR / TIR provisioned
2 unknown (e.g. no network, etc.)
Implementation
Optional.
7.32 Service specific access control restriction status +CSSAC
Table 7.32-1: +CSSAC action command syntax
Command
Possible response(s)
+CSSAC +CSSAC: <BFVoice>,<BFVideo>,<BTVoice>,<
BTVideo>
+CSSAC=?
Description
This command refers to SSAC (Service Specific Access Control) related information which is used by MMTEL
application (see 3GPP TS 24.173 [87]). The command provides the current status of the parameters for SSAC,
<BFVoice>, <BFVideo>, <BTVoice> and <BTVideo>. The AT command has no effect on the execution of
SSAC.
Defined values
<BFVoice> integer type; parameter shows the barring factor for MMTEL voice. <BFVoice> is mapped to the
BarringFactorForMMTEL-Voice as in table 7.32-2.
ETSI
ETSI
TS 127 007 V13.3.0 (2016
-
03)
89
3GPP TS 27.007 version 13.3.0 Release 13
Table 7.32-2: Value of BFVoice and its interpretation by MMTEL application
<BFVoice>
BarringFactorForMMTEL
-
Voice
as specified in
3GPP TS 24.173 [87]
0 0
1 0,05
2 0,1
3 0,15
4 0,2
5 0,25
6 0,3
7 0,4
8 0,5
9 0,6
10 0,7
11 0,75
12 0,8
13 0,85
14 0,9
15 0,95
16 1
<BFVideo> integer type; parameter shows the barring factor for MMTEL video. <BFVideo> is mapped to the
BarringFactorForMMTEL-Video as in table 7.32-3.
Table 7.32-3: Value of BFVideo and its interpretation by MMTEL application
<BFVideo>
BarringFactorForMMTEL
-
V
ideo
as specified in
3GPP TS 24.173 [87]
0 0
1 0,05
2 0,1
3 0,15
4 0,2
5 0,25
6 0,3
7 0,4
8 0,5
9 0,6
10 0,7
11 0,75
12 0,8
13 0,85
14 0,9
15 0,95
16 1
<BTVoice> integer type; parameter shows the barring timer for MMTEL voice. <BTVoice> is mapped to the
BarringTimeForMMTEL-Voice as in table 7.32-4.
Table 7.32-4: Value of BTVoice and its interpretation by MMTEL application
<BTVoice>
Barring
Time
ForMMTEL
-
V
oice
as
specified in 3GPP TS 24.173 [87]
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
90
3GPP TS 27.007 version 13.3.0 Release 13
0 0
1 4
2 8
3 16
4 32
5 64
6 128
7 256
8 512
<BTVideo> integer type; parameter shows the barring timer for MMTEL video. <BTVideo> is mapped to the
BarringTimeForMMTEL-Video as in table 7.32-5.
Table 7.32-5: Value of BTVideo and its interpretation by MMTEL application
<BTVideo>
Barring
Time
ForMMTEL
-
V
ideo
as
specified in 3GPP TS 24.173 [87]
0 0
1 4
2 8
3 16
4 32
5 64
6 128
7 256
8 512
Implementation
Optional.
This command is not applicable to UTRAN or GERAN UEs.
7.33 Network emergency bearer services support +CNEM
Table 7.33-1: +CNEM parameter command syntax
Command
Possible response(s)
+CNEM=[<reporting>]
+CME ERROR: <err>
+CNEM? +CNEM: <reporting>[,<emb_Iu_supp>,<e
mb_S1_supp>]
+CNEM=? +CNEM: (list of supported <reporting>s)
Description
Set command enables reporting of changes in the emergency bearer services support indicators with the unsolicited
result code +CNEMIU: <emb_Iu_supp> according to the network feature support information element, see
3GPP TS 24.008 [8] subclause 10.5.5.23 and the unsolicited result code +CNEMS1: <emb_S1_supp> according to
the EPS network feature support information element, see 3GPP TS 24.301 [83] subclause 9.9.3.12A. Refer
subclause 9.2 for possible <err> values.
Read command returns current command setting and if enabled, the settings of the emergency bearer services support
indicator in Iu mode and the emergency bearer services support indicator in S1 mode for the network where the UE is
attached.
Test command returns values supported as a compound value.
Defined values
<reporting>: integer type
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
91
3GPP TS 27.007 version 13.3.0 Release 13
0 Reporting not enabled
1 Reporting enabled
<emb_Iu_supp>: integer type. Emergency bearer services support indicator for Iu mode (See NOTE).
0 Emergency bearer services in Iu mode and A/Gb mode not supported
1 Emergency bearer services supported in Iu mode, but not supported in A/Gb mode
<emb_S1_supp>: integer type. Emergency bearer services support indicator for S1 mode (See NOTE).
0 Emergency bearer services in S1 mode not supported
1 Emergency bearer services in S1 mode supported
NOTE: The indicators <emb_Iu_supp> and <emb_S1_supp> are only set to supported when explicitly
signalled from the network. When an emergency bearer services support indicator is not signalled from
the network or if no network is available, this is interpreted as "Emergency bearer services not
supported".
Implementation
Optional.
7.34 Enhanced closed user group +CECUG
Table 7.34-1: +CECUG parameter command syntax
Command
Possible response(s)
+CECUG=<n>,[<CUG_pointer>[,
<CUG_index>,<CUG_info>]]
+CECUG? [+CECUG: <n>,<CUG_pointer>,<CUG_index>,
<CUG_info>
[<CR><LF>+CECUG: <n>,<CUG_pointer>,<CUG
_index>,<CUG_info>
[...]]]
+CECUG=? +CECUG: (list of supported <n>s),(range of supported
<CUG_pointer>s)
Description
This command allows control of the Closed User Group supplementary service (refer 3GPP TS 22.085 [21] and
3GPP TS 24.654 [121]). Set command enables the served subscriber to create a number of <CUG_pointer>s that
each define a <CUG_index> and a <CUG_info> to define how the preferential CUG and the Outgoing Access (OA)
is handled for outgoing calls.
Set command with <n>=0 disable settings in the MT and use the subscribed settings, while <n>=1 enables to control
the CUG information on the air interface as adjustments for outgoing calls according to the settings defined by the
parameters <CUG_pointer>s, <CUG_index> and <CUG_info>. For calls initated using the dial command D, the
dial string modifiers 'G' or 'g' can not indicate a <CUG_pointer> and the <CUG_index> and <CUG_info> as
defined for <CUG_pointer>=1 shall be used.
NOTE 1: On a per call basis CUG functionality is explained in the subclauses "ITU-T Recommendation V.250 [14]
dial command D" and "Dial URI +CDU".
A special form of the set command, +CECUG=<n>,<CUG_pointer> causes the value of <CUG_index> and
<CUG_info> for the CUG pointer <CUG_pointer> to become undefined. The set command, +CECUG=0 that can
be used to disable the CUG temporary mode will not make previously defined CUG pointers and the corresponding
defined <CUG_index> and <CUG_info> undefined.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
92
3GPP TS 27.007 version 13.3.0 R
elease 13
The read command returns the current settings for each defined CUG pointer.
The test command returns values supported as compound values.
Defined values
<n>: integer type. This parameter sets CUG activation on a per call basis.
0 disable CUG temporary mode. All calls initiated using the dial command D or +CDU use the subscribed CUG
settings. The parameters <CUG_index> and <CUG_info> are ignored at call initiation. For calls initated
using the dial command D, the dial string modifiers 'G' or 'g' have no effect (see subclause "ITU T
Recommendation V.250 [14] dial command D"). For calls initated using +CDU, the parameter
<CUG_pointer> has no effect (see subclause "Dial URI +CDU").
1 enable CUG temporary mode. Values for <CUG_index> and <CUG_info> are applied for:
- all calls initiated using the dial command D where the dial modifier 'G' or 'g' (see subclause "ITU T
Recommendation V.250 [14] dial command D") is present as part of the dial string.
- all calls initated using +CDU where parameter <CUG_pointer> is set to 1 (see subclause "Dial URI
+CDU")
If 'G' or 'g' is not applied (for the dial command D) or <CUG_pointer> is set to 0 (for +CDU)
<CUG_index> and <CUG_info> are ignored. In that case only the subscribed CUG settings apply.
<CUG_pointer>: integer type. A numeric parameter which specifies a particular set of CUG data. The
<CUG_pointer> is local to the TE-MT interface and identifies a particular <CUG_index> and
<CUG_info> which indicates per call basis changes provided to the supplementary service closed user group.
The range of permitted values is from 1-n.The maximum value of n is implementation specific.
NOTE 2: 3GPP TS 22.085 [21] indicates that each individual subscriber can be a member of a maximum of 10
CUGs.
<CUG_index>: string type. The parameter sets the CUG index for this <CUG_pointer>.
"0" ... "32767" CUG index
"" no CUG index, indicated by empty string. Preferential CUG taken from subscriber data.
<CUG_info>: integer type. The parameter sets the CUG information for this <CUG_pointer>.
0 no information
1 suppress OA
2 suppress preferential CUG
3 suppress OA and preferential CUG
Implementation
Optional. This command can replace the command +CCUG.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
93
3GPP TS 27.007 version 13.3.0 Release 13
7.35 Communication forwarding number and conditions with URI
support +CCFCU
Table 7.35-1: +CCFCU action command syntax
Command
Possible response(s)
+CCFCU=<reason>,<mode>[,
<numbertype>,<ton>,<numb
er>[,<class>,<ruleset>
[,<subaddr>[,<satype>[,<
time>]]]]]
+CME ERROR: <err>
when <mode>=2 and command successful:
+CCFCU: <status>,<class1>[,<numbertype>,<ton>,<nu
mber>[,<subaddr>,<satype>[,<time>]]]
[<CR><LF>+CCFCU: <status>,<class2>[,<number>,<typ
e>[,<subaddr>,<satype>[,<time>]]]
[...]]
+CCFCU=? +CCFCU: (list of supported <reason>s)
Description
The command allows control of the communication forwarding supplementary service according to
3GPP TS 22.072 [31], 3GPP TS 22.082 [4] and 3GPP TS 24.604 [132]. This command is an extended version of AT
commands +CCFC and +CTFR which also supports numbers of the SIP URI format. Registration, erasure, activation,
deactivation, and status query are supported. When querying the status of a network service (<mode>=2) the response
line for 'not active' case (<status>=0) should be returned only if service is not active for any <class>.
Test command returns reason values supported as a compound value.
Defined values
<reason>: integer type
0 communication forwarding unconditional – CFU, refer 3GPP TS 22.082 [4] and 3GPP TS 24.604 [132]
1 communication forwarding on busy user – CFB, refer 3GPP TS 22.082 [4] and 3GPP TS 24.604 [132]
2 communication forwarding on no reply – CFNR, refer 3GPP TS 22.082 [4] and 3GPP TS 24.604 [132]
3 communication forwarding on subscriber not reachable – CFNRc, refer 3GPP TS 22.082 [4] and
3GPP TS 24.604 [132]
4 all call forwarding (refer to "all CF" in 3GPP TS 22.030 [19])
5 all conditional call forwarding (refer to "all conditional CF" in 3GPP TS 22.030 [19])
6 communication deflection – CD, refer 3GPP TS 22.072 [31] and 3GPP TS 24.604 [132]
7 communication forwarding on not logged-in – CFNL, refer 3GPP TS 24.604 [132]
<mode>: integer type
0 disable
1 enable
2 query status
3 registration
4 erasure
<numbertype>: integer type. Indicating type of information in parameter <number>.
0 No valid information in parameter <number>. <number> shall then be set to empty string ("").
ETSI
ETSI TS 127 007 V13.3.
0 (2016
-
03)
94
3GPP TS 27.007 version 13.3.0 Release 13
1 Number in <number> according to URI including the prefix specifying the URI type (see command +CDU).
Parameter <ton> has no relevant information and is set to zero.
2 Number in <number> according to one of the formats supported by 3GPP TS 24.008 [8]
subclause 10.5.4.7)
<ton>: type of number in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7). The parameter is also set
to zero when it has no meaningful content, e.g. when <numbertype>=1.
<number>: string type phone number in format specified by <numbertype>. The used character set should be
the one selected with Select TE Character Set +CSCS. When no number is available, <number> shall be set to
empty string ("").
<subaddr>: string type subaddress of format specified by <satype>
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8); default 128
<classx> is a sum of integers each representing a class of information (default 7 - voice, data and fax):
0 communication forwarding without differentiation on class of information
1 voice (telephony)
2 data (refers to all bearer services; with <mode>=2 this may refer only to some bearer service if TA does
not support values 16, 32, 64 and 128)
4 fax (facsimile services)
8 short message service
16 data circuit sync
32 data circuit async
64 dedicated packet access
128 dedicated PAD access
<ruleset>: string type ruleset value of XML element of communication diversion XML document (refer
3GPP TS 24.604 [132]). If XML ruleset values are not supported or intended to be used, the parameter shall be
set to an empty string ("").
<time>: integer type
1...30 when "no reply", "all call forwarding" or "all conditional call fowarding" is enabled or queried, this gives
the time in seconds to wait before call is forwarded, default value 20.
<status>: integer type
0 not active
1 active
Implementation
Optional.
7.36 Message waiting indication control +CMWI
Table 7.36-1: +CMWI parameter command syntax
Command
Possible response(s)
+CMWI=[<state>[,<expiry_
time>]] +CME ERROR: <err>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
95
3GPP TS 27.007 version 13.3.0 Release 13
+CMWI? +CMWI: <state>[,<expiry_time>]
+CMWI=? +CMWI: (list of supported <state>s),(maximum
<expiry_time>)
Description
The command allows to control the message waiting indication service according to 3GPP TS 24.606 [134].
The set command invokes the service for a certain <expiry_time> or deactivates the service. Refer subclause 9.2
for possible <err> values.
When the message waiting indication service is activated the unsolicited result code
+CMWN: <mw_notification> is provided to indicate waiting messages.
The read command returns the message waiting indication service state and the time remaining for the service to be
active if available.
Test command returns values supported as compound values. <expiry_time>s are supported from 0 to (maximum
<expiry_time>) in seconds.
Defined values
<state>: integer type. Indicates the state of the message waiting indication service.
0 not active
1 active
<expiry_time>: integer type. Indicates the time in seconds after which the message waiting indication service
will become inactive. The range of permitted values is from 0 to (2**32)-1. The default value is implementation
specific.
<mw_notification>: string type. Indicates waiting message information in application/simple-message-
summary MIME type format according to 3GPP TS 24.606 [134].
Implementation
Optional.
7.37 Session start and stop for smart congestion mitigation
+CSCM
Table 7.37-1: +CSCM action command syntax
Command
Possible response(s)
+CSCM=<application>,<start
-end_indication> +CME ERROR: <err>
+CSCM=? +CSCM: (list of supported
<application>s),(list of supported
<start-end_indication>s)
Description
This command allows the MMTEL and SMS over IP applications to provide start and stop indications to the MT, for
MMTEL voice, MMTEL video or SMSoverIP sessions, in support of smart congestion mitigation in E-UTRAN.
The set command allows the:
- MMTEL application to provide an indication to the MT when an originating multimedia telephony session for
voice communication is started or ended according to the conditions in 3GPP TS 24.173 [87]).
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
96
3GPP TS 27.007 version 13.3.0 Release 13
- MMTEL application to provide an indication to the MT when an originating multimedia telephony session for
video communication is started or ended according to the conditions in 3GPP TS 24.173 [87]).
- SMS over IP application to provide an indication to the MT when an originating SMS over IP is started or ended
according to the conditions in 3GPP TS 24.341 [101].
Refer subclause 9.2 for possible <err> values.
The test command returns the supported values as compound values.
Defined values
<application>: integer type. Type of application.
0 MMTEL voice
1 MMTEL video
2 SMS over IP
<start-end_indication>: integer type. Indication of the start or the end of the session as indicated by
<application>.
1 Start indication
2 End indication
Implementation
Optional.
This command is not applicable to UTRAN or GERAN UEs.
7.38 Power Saving Mode Setting +CPSMS
Table 7.38-1: +CPSMS parameter command syntax
Command
Possible response(s)
+CPSMS=[<mode>[,<Requested_Peri
odic-RAU>[,<Requested_GPRS-
READY-
timer>[,<Requested_Periodic-
TAU>[,<Requested_Active-
Time>]]]]]
+CME ERROR: <err>
+CPSMS? +CPSMS: <mode>,[<Requested_Periodic-
RAU>],[<Requested_GPRS-READY-
timer>],[<Requested_Periodic-
TAU>],[<Requested_Active-Time>]
+CPSMS=? +CPSMS: (list of supported <mode>s),(list of supported
<Requested_Periodic-RAU>s),(list of supported
<Requested_GPRS-READY-timer>s),(list of supported
<Requested_Periodic-TAU>s),(list of supported
<Requested_Active-Time>s)
Description
The set command controls the setting of the UEs power saving mode (PSM) parameters. The command controls
whether the UE wants to apply PSM or not, as well as the requested extended periodic RAU value and the requested
GPRS READY timer value in GERAN/UTRAN, the requested extended periodic TAU value in E-UTRAN and the
requested Active Time value. See the unsolicited result codes provided by commands +CGREG for the Active Time
value, the extended periodic RAU value and the GPRS READY timer value that are allocated to the UE by the network
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
97
3GPP TS 27.007 version 13.3.0 Release 13
in GERAN/UTRAN and +CEREG for the Active Time value and the extended periodic TAU value that are allocated to
the UE by the network in E-UTRAN.
A special form of the command can be given as +CPSMS= (with all parameters omitted). In this form, the parameter
<mode> will be set to 0, the use of PSM will be disabled and data for all parameters in command +CPSMS will be
removed or, if available, set to the manufacturer specific default values.
Refer subclause 9.2 for possible <err> values.
The read command returns the current parameter values.
The test command returns the supported <mode>s and the value ranges for the requested extended periodic RAU value
and the requested GPRS READY timer value in GERAN/UTRAN, the requested extended periodic TAU value in E-
UTRAN and the requested Active Time value as compound values.
Defined values
<mode>: integer type. Indication to disable or enable the use of PSM in the UE.
0 Disable the use of PSM
1 Enable the use of PSM
<Requested_Periodic-RAU>: string type; one byte in an 8 bit format. Requested extended periodic RAU
value (T3312) to be allocated to the UE in GERAN/UTRAN. The requested extended periodic RAU value is
coded as one byte (octet 3) of the GPRS Timer 3 information element coded as bit format (e.g. "01000111"
equals 70 hours). For the coding and the value range, see the GPRS Timer 3 IE in 3GPP TS 24.008 [8]
Table 10.5.163a/3GPP TS 24.008. See also 3GPP TS 23.682 [149] and 3GPP TS 23.060 [47]. The default value,
if available, is manufacturer specific.
<Requested_GPRS-READY-timer>: string type; one byte in an 8 bit format. Requested GPRS READY timer
value (T3314) to be allocated to the UE in GERAN/UTRAN. The requested GPRS READY timer value is coded
as one byte (octet 2) of the GPRS Timer information element coded as bit format (e.g. "01000011" equals 3
decihours or 18 minutes). For the coding and the value range, see the GPRS Timer IE in 3GPP TS 24.008 [8]
Table 10.5.172/3GPP TS 24.008. See also 3GPP TS 23.060 [47]. The default value, if available, is manufacturer
specific.
<Requested_Periodic-TAU>: string type; one byte in an 8 bit format. Requested extended periodic TAU
value (T3412) to be allocated to the UE in E-UTRAN. The requested extended periodic TAU value is coded as
one byte (octet 3) of the GPRS Timer 3 information element coded as bit format (e.g. "01000111" equals 70
hours). For the coding and the value range, see the GPRS Timer 3 IE in 3GPP TS 24.008 [8]
Table 10.5.163a/3GPP TS 24.008. See also 3GPP TS 23.682 [149] and 3GPP TS 23.401 [82]. The default value,
if available, is manufacturer specific.
<Requested_Active-Time>: string type; one byte in an 8 bit format. Requested Active Time value (T3324) to
be allocated to the UE. The requested Active Time value is coded as one byte (octet 3) of the GPRS Timer 2
information element coded as bit format (e.g. "00100100" equals 4 minutes). For the coding and the value range,
see the GPRS Timer 2 IE in 3GPP TS 24.008 [8] Table 10.5.163/3GPP TS 24.008. See also
3GPP TS 23.682 [149], 3GPP TS 23.060 [47] and 3GPP TS 23.401 [82]. The default value, if available, is
manufacturer specific.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
98
3GPP TS 27.007 version 13.3.0 Release 13
7.39 Application Start and Stop indication for ACDC +CACDC
Table 7.39-1: +CACDC action command syntax
Command
Possible response(s)
+CACDC=<OSid>,<OSappid>,
<start-stop-indication> +CME ERROR: <err>
+CACDC=? +CACDC: (list of supported <OSid>,<OSappid>
pairs),(list of supported <start-stop-
indication>s)
Description
This command allows the operating system on the TE to provide start and stop indications to the MT for a particular
application in support of ACDC (Application specific Congestion control for Data Communications). Each application
is identified by an application identity which consists of two parts:
<OSid> an operating system identifier. This identifier identifies the operating system.
<OSappid> an OS specific application identifier. This identifier is associated with a given application and
uniquely identifies the application within the UE for a given operating system.
The supported <OSid>s and <OSappid>s are manufacturer specific.
Refer subclause 9.2 for possible <err> values.
The test command returns the supported values as compound values.
Defined values
<OSid>: string type. Operating system identifier. The format of the OS ID is a Universally Unique IDentifier
(UUID) as specified in RFC 4122 [155].
<OSappid>: string type. A string containing the OS specific application identifier. The format of the OS specific
application identifier is manufacturer specific.
<start-stop-indication>: integer type. Indication to start sending data and the indication to stop sending
data, for the application identified by <OSid> and <OSappid>.
0 indication to start sending data
1 indication to stop sending data
Implementation
Optional.
This command is not applicable to GERAN UEs.
7.40 Informative examples
This subclause includes all the GSM/UMTS supplementary service related commands, additional commands to lock
MT and SIM/UICC capabilities, and commands to check the network registration status.
An example where MSISDNs of a MT are queried, calls are forwarded to different numbers when mobile is busy (CFB)
or when it does not answer (CFNRy). The status of CFNRy is read:
AT+CNUM
+CNUM: ,"+358501234567",145,,4 (voice number)
OK
AT+CCFC=1,1,"931123456" (enable CFB)
OK
AT+CCFC=2,1,"921654321" (enable CFNRy)
OK
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
99
3GPP
TS 27.007 version 13.3.0 Release 13
AT+CCFC=1,2 (query CFNRy)
+CCFC: 1,7,"+35821654321",145,,,20 (forward after 20 seconds)
OK
An example of Call Waiting (+CCWA), Call Related Supplementary Services (+CHLD), and Connected Line
Identification Presentation (+COLP) usage:
AT+CCWA=1,1;+COLP=1 (enable call waiting and COLP result codes)
OK
ATD9311234567; (originate a voice call)
+COLP: "+358311234567",145
OK
...conversation...
+CCWA: "+358317654321",145 (another call is waiting)
AT+CHLD=2 (put first call on hold and answer the second one)
OK
...conversation...
AT+CHLD=1 (release the second (active) call and recover the first (held) call)
OK
ATH (release the first call)
OK
Call barring supplementary services are combined in one command, Facility Lock (+CLCK), which is also used to
restrict MT and SIM/UICC functionality Some of the facilities require a password when enabled or disabled. An
additional command, Change Password (+CPWD), is defined for changing the password of different barring and
restriction facilities. An example where locking status of outgoing international calls is interrogated and then barred,
and the password of the SIM/UICC card lock (Personal Identity Number, PIN) is changed:
AT+CLCK="OI",2
+CLCK: 0,7
OK
AT+CLCK="OI",1,"1234"
OK
AT+CPWD="SC","4321","1234"
OK
Operator Selection (+COPS) command is used for querying the status of all GSM/UMTS operators detected in the area,
and switching between operators.
Following example illustrates a network selection sequence in Finland. Two operators are found, the status of Tele is
unknown and Radiolinja is currently selected. Read command shows that automatic selection mode is on and that
Radiolinja is selected. Then an attempt is made to access Tele, but it is denied (shown by +CME ERROR).
AT+COPS=?
+COPS: (2,"RADIOLINJA","RL","24405"),(0,"TELE","TELE","24491")
OK
AT+COPS?
+COPS: 0,0,"RADIOLINJA"
OK
AT+COPS=1,0,"TELE"
+CME ERROR: 3
When a terminal wanders between countries (i.e. networks), an application may follow this e.g. with the following
scenario:
AT+CREG=1 (enable +CREG: <stat> unsolicited result code)
OK
AT+CREG?
+CREG: 1,1 (MT is registered in home PLMN)
OK
AT+COPS=3,2;+COPS?;+COPS=3,0;+COPS?
+COPS: 0,2,"24405" (get the country...
+COPS: 0,0,"RADIOLINJA" ...and operator name)
OK
...user wanders to another PLMN...
+CREG: 2 (deregistered, roaming ongoing)
+CREG: 5 (registered again, not home PLMN)
AT+COPS=3,2;+COPS?;+COPS=3,0;+COPS?
+COPS: 0,2,"24001" (get the country...
+COPS: 0,0,"TELIA MOBITEL" ...and operator name)
OK
...user loses connection, no other PLMNs around...
+CREG: 0
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
100
3GPP TS 27.007 version 13.3.0 Release 13
An example of eMLPP Supplementary Service usage for a ptp voice call:
ATD*752#+436644101453; (originate a voice call with the priority level 2, see for priority level definitions GSM 02.30)
OK (call setup was successful)
8 Mobile termination control and status commands
8.0 General
This clause includes commands for MT power, keypad, touch screen, display and indicator handling. Also commands
for selecting, reading and writing of phonebooks, and setting real-time clock facilities are specified. Two commands are
specified for accessing SIM/UICC database records in a general way.
Figure 7 illustrates the effect of these commands. Command Phone Activity Status +CPAS indicates the current general
activity status of the MT. Command Set Phone Functionality +CFUN is used to set the MT to different power
consumption states. Command Enter PIN +CPIN is used to enter MT passwords which are needed before any other
functionality of the MT can be used (e.g. SIM PIN, PUK). Commands Generic SIM Access +CSIM and Restricted SIM
Access +CRSM can be used to access all data in SIM/UICC. Commands Battery Charge +CBC and Signal Quality +CSQ
are same as in TIA IS-135 [16] and they are used to query the battery charge of the MT and the current RSSI of the MT.
Command Mobile Termination Control Mode +CMEC is used to select the controlling unit of MT keypad, display touch
screen, and indicators. Controlling commands for the TE are Keypad Emulation +CKPD, Display Control +CDIS,
Touch Screen Emulation +CTSA, and Indicator Control +CIND. If corresponding event reporting is enabled with
command Mobile Termination Event Reporting +CMER, +CKEV is the result code of a keypad event, +CDEV is the
result code of a display event, +CTEV is the result code of a touch screen event, +COEV is the result code of a display
orientation event, and +CIEV is the result code of an indicator event. Phonebook commands are Select Phonebook
Memory Storage +CPBS, Read Phonebook Entries +CPBR, Find Phonebook Entries +CPBF and Write Phonebook
Entry +CPBW. Additional command Clock +CCLK can be used to control the real-time clock of the MT if available.
Command Alarm +CALA sets possible alarm clock facilities of the MT.
+CFUN SIM IFY PASSWORD FACILITIES +CBC KEVPAD vCKEV DISPLAY ,CDEV up INDICATORS ,CIEV [ID PHONE- BOOKS MT A ETSI
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
101
3GPP TS 27.007 version 13.3.0 Release 13
KEYPAD
MT
TA
+CKPD
+CMER
+CKEV
+CIEV
+CDIS
+CIND
DISPLAY
INDICATORS
+CDEV
+CMEC
PHONE-
BOOKS
+CPBS
+CPBW
+CPBR, +CPBF
TE
+CFUN
+CPAS
+CCLK, +CALA
+CBC
+CSQ
+CPIN, +CSIM, +CRSM
SIM IF,
PASSWORD
FACILITIES
+CIEV
+CIND
INDICATORS
Figure 7: Mobile termination control and status commands
8.1 Phone activity status +CPAS
Table 60: +CPAS action command syntax
Command
Possible response(s)
+CPAS +CPAS: <pas>
+CME ERROR: <err>
+CPAS=? +CPAS: (list of supported <pas>s)
+CME ERROR: <err>
Description
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
102
3GPP TS 27.007 version 13.3.0 Release 13
Execution command returns the activity status <pas> of the MT. It can be used to interrogate the MT before requesting
action from the phone. Refer subclause 9.2 for possible <err> values.
Test command returns values supported by the MT as a compound value.
Defined values
<pas>: integer type
0 ready (MT allows commands from TA/TE)
1 unavailable (MT does not allow commands from TA/TE)
2 unknown (MT is not guaranteed to respond to instructions)
3 ringing (MT is ready for commands from TA/TE, but the ringer is active)
4 call in progress (MT is ready for commands from TA/TE, but a call is in progress)
5 asleep (MT is unable to process commands from TA/TE because it is in a low functionality state)
all other values below 128 are reserved by the present document.
Implementation
Mandatory when MT can be operated from TE (refer subclause "Mobile Termination control mode +CMEC").
8.2 Set phone functionality +CFUN
Table 61: +CFUN parameter command syntax
Command
Possible response(s)
+CFUN=[<fun>[,<rst>]] +CME ERROR: <err>
+CFUN? +CFUN: <fun>
+CME ERROR: <err>
+CFUN=? +CFUN: (list of supported <fun>s),(list of supported <rst>s)
+CME ERROR: <err>
Description
Set command selects the level of functionality <fun> in the MT. Level "full functionality" is where the highest level of
power is drawn. "Minimum functionality" is where minimum power is drawn. Level of functionality between these may
also be specified by manufacturers. When supported by manufacturers, MT resetting with <rst> parameter may be
utilized. Refer subclause 9.2 for possible <err> values.
NOTE 1: It is manufacturer specific if this command affects network registration. Command Operator Selection
+COPS is used to force registration/deregistration.
Read command returns the current setting of <fun>.
Test command returns values supported by the MT as compound values.
Defined values
<fun>: integer type
0 minimum functionality
1 full functionality. Enable (turn on) the transmit and receive RF circuits for all supported radio access
technologies. For MTs supporting +CSRA, this equals the RATs indicated by the response of
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
103
3GPP TS 27.007 version 13.3.0 Release 13
+CSRA=?. Current +CSRA setting is ignored. It is not required that the MT transmit and receive RF
circuits are in a disabled state for this setting to have effect.
2 disable (turn off) MT transmit RF circuits only
3 disable (turn off) MT receive RF circuits only
4 disable (turn off) both MT transmit and receive RF circuits
5...127 reserved for manufacturers as intermediate states between full and minimum functionality
128 Full functionality with radio access support according to the setting of +CSRA. Enables (turns on) the
transmit and receive RF circuits if not already enabled. This <fun> setting is applicable for MTs
supporting +CSRA.
129 Prepare for shutdown. This setting has its prime use when some of the MT"s resources (e.g. file system)
are located on a tightly integrated TE (host). The MT will execute pending actions resulting in
"permanent" changes, e.g. execute pending file system operations. The MT will also make an orderly
network detach. After this action and +CFUN has returned OK, the MT can be shut down with
<fun>=0, or by other means. After setting <fun>=129, only <fun>=0 is valid. All other values will
make +CFUN return ERROR.
<rst>: integer type
0 do not reset the MT before setting it to <fun> power level
NOTE 2: This shall be always default when <rst> is not given.
1 reset the MT before setting it to <fun> power level
Implementation
Optional. When <fun>=128, is supported, +CSRA is required.
8.3 Enter PIN +CPIN
Table 62: +CPIN parameter command syntax
Command
Possible response(s)
+CPIN=<pin>[,<newpin>] +CME ERROR: <err>
+CPIN? +CPIN: <code>
+CME ERROR: <err>
+CPIN=?
Description
Set command sends to the MT a password which is necessary before it can be operated (SIM PIN, SIM PUK, PH-SIM
PIN, etc.). If the PIN is to be entered twice, the TA shall automatically repeat the PIN. If no PIN request is pending, no
action is taken towards MT and an error message, +CME ERROR, is returned to TE. Refer subclause 9.2 for possible
<err> values.
NOTE 1: SIM PIN, SIM PUK, PH-SIM PIN, PH-FSIM PIN, PH-FSIM PUK, SIM PIN2 and SIM PUK2
refer to the PIN of the selected application on the UICC. For example, in an UTRAN context, the selected
application on the currently selected UICC should be a USIM and the SIM PIN then represents the PIN
of the selected USIM. See 3GPP TS 31.101 [65] for further details on application selection on the UICC.
If the PIN required is SIM PUK or SIM PUK2, the second pin is required. This second pin, <newpin>, is used to
replace the old pin in the SIM.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
104
3GPP TS 27.00
7 version 13.3.0 Release 13
NOTE 2: Commands which interact with MT that are accepted when MT is pending SIM PIN, SIM PUK, or
PH-SIM are: +CGMI, +CGMM, +CGMR, +CGSN, D112; (emergency call), +CPAS, +CFUN, +CPIN,
+CPINR, +CDIS (read and test command only), and +CIND (read and test command only). It is
implementation specific whether additional commands can be accepted when MT is pending SIM PIN,
SIM PUK, or PH-SIM.
Read command returns an alphanumeric string indicating whether some password is required or not.
Defined values
<pin>, <newpin>: string type values
<code> values reserved by the present document:
READY MT is not pending for any password
SIM PIN MT is waiting SIM PIN to be given
SIM PUK MT is waiting SIM PUK to be given
PH-SIM PIN MT is waiting phone-to-SIM card password to be given
PH-FSIM PIN MT is waiting phone-to-very first SIM card password to be given
PH-FSIM PUK MT is waiting phone-to-very first SIM card unblocking password to be given
SIM PIN2 MT is waiting SIM PIN2 to be given (this <code> is recommended to be returned only
when the last executed command resulted in PIN2 authentication failure (i.e. +CME
ERROR: 17); if PIN2 is not entered right after the failure, it is recommended that MT
does not block its operation)
SIM PUK2 MT is waiting SIM PUK2 to be given (this <code> is recommended to be returned only
when the last executed command resulted in PUK2 authentication failure (i.e. +CME
ERROR: 18); if PUK2 and new PIN2 are not entered right after the failure, it is
recommended that MT does not block its operation)
PH-NET PIN MT is waiting network personalization password to be given
PH-NET PUK MT is waiting network personalization unblocking password to be given
PH-NETSUB PIN MT is waiting network subset personalization password to be given
PH-NETSUB PUK MT is waiting network subset personalization unblocking password to be given
PH-SP PIN MT is waiting service provider personalization password to be given
PH-SP PUK MT is waiting service provider personalization unblocking password to be given
PH-CORP PIN MT is waiting corporate personalization password to be given
PH-CORP PUK MT is waiting corporate personalization unblocking password to be given
Implementation
Mandatory for MT not supporting the +CKPD command and supporting AT commands only.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
105
3GPP TS 27.007 version 13.3.0 Release 13
8.4 Battery charge +CBC
Table 63: +CBC action command syntax
Command
Possible response(s)
+CBC +CBC: <bcs>,<bcl>
+CME ERROR: <err>
+CBC=? +CBC: (list of supported <bcs>s),(list of supported <bcl>s)
Description
Execution command returns battery connection status <bcs> and battery charge level <bcl> of the MT. Refer
subclause 9.2 for possible <err> values.
Test command returns values supported as compound values.
Defined values
<bcs>: integer type
0 MT is powered by the battery
1 MT has a battery connected, but is not powered by it
2 MT does not have a battery connected
3 Recognized power fault, calls inhibited
<bcl>: integer type
0 battery is exhausted, or MT does not have a battery connected
1...100 battery has 1-100 percent of capacity remaining
Implementation
Optional.
8.5 Signal quality +CSQ
Table 64: +CSQ action command syntax
Command
Possible response(s)
+CSQ +CSQ: <rssi>,<ber>
+CME ERROR: <err>
+CSQ=? +CSQ: (list of supported <rssi>s),(list of supported <ber>s)
Description
Execution command returns received signal strength indication <rssi> and channel bit error rate <ber> from the
MT. Refer subclause 9.2 for possible <err> values.
Test command returns values supported as compound values.
Defined values
<rssi>: integer type
0 -113 dBm or less
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
106
3GPP TS 27.007 version 13.3.0 Release 13
1 -111 dBm
2...30 -109... -53 dBm
31 -51 dBm or greater
99 not known or not detectable
<ber>: integer type; channel bit error rate (in percent)
0...7 as RXQUAL values in the table in 3GPP TS 45.008 [20] subclause 8.2.4
99 not known or not detectable
Implementation
Optional.
8.6 Mobile termination control mode +CMEC
Table 65: +CMEC parameter command syntax
Command
Possible response(s)
+CMEC=[<keyp>[,<disp>[,<ind>[,<
tscrn>]]] +CME ERROR: <err>
+CMEC? +CMEC: <keyp>,<disp>,<ind>,<tscrn>
+CMEC=?
+CMEC: (list of supported <keyp>s),(list of
supported <disp>s),(list of supported
<ind>s),(list of supported <tscrn>s)
Description
Set command selects the equipment, which operates MT keypad, writes to MT display and sets MT indicators. If
operation mode is not allowed by the MT, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible
<err> values.
Read command returns the current settings.
Test command returns the modes supported as compound values.
Defined values
<keyp>: integer type
0 MT can be operated only through its keypad (execute command of +CKPD cannot be used)
1 MT can be operated only from TE (with command +CKPD)
2 MT can be operated from both MT keypad and TE
<disp>: integer type
0 only MT can write to its display (command +CDIS can only be used to read the display)
1 only TE can write to MT display (with command +CDIS)
2 MT display can be written by both MT and TE
<ind>: integer type
0 only MT can set the status of its indicators (command +CIND can only be used to read the indicators)
1 only TE can set the status of MT indicators (with command +CIND)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
107
3GPP TS 27.007 version 13.3.0 Release 13
2 MT indicators can be set by both MT and TE
<tscrn>: integer type
0 only MT can set the status of its indicators (execute command of +CTSA cannot be used)
1 only TE can set the status of MT indicators (with command +CTSA)
2 MT indicators can be set by both MT and TE
Implementation
Mandatory when any of keypad, display or indicator or touch screen commands is implemented.
8.7 Keypad control +CKPD
Table 66: +CKPD action command syntax
Command
Possible response(s)
+CKPD=<keys>[,<time>[,<pause>]] +CME ERROR: <err>
+CKPD=?
Description
Execution command emulates MT keypad by giving each keystroke as a character in a string <keys>. <time>*0.1
seconds is the time to stroke each key and <pause>*0.1 seconds is the length of pause between two strokes. If
emulating fails in an MT error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
This command should be accepted (OK returned) before actually starting to press the keys. Thus unsolicited result codes
of key pressings and display events can be returned (refer subclause "Mobile Termination event reporting +CMER").
Defined values
<keys>: string of characters representing keys as listed in the following table 67 (based on PCCA STD-101 [17]
Annex I table I-3). Colon character (IRA 58) followed by one character can be used to indicate a manufacturer
specific key not listed here. All characters from a semicolon character (IRA 59) to the next single semicolon
character are treated as alpha entries and are not converted to key equivalents. All semicolon characters inside
alpha entries should be duplicated in the TE and stripped to one before entering to the MT. Pause character (IRA
87 or 119) can be used to pause between key pressings for a time specified by <pause>. All IRA values not
listed here are reserved.
Table 67: Character codes
Char
IRA (dec)
Comment (+ some known key symbols)
# 35 hash (number sign)
% 37 percent sign (P)
* 42 star (*)
0... 9 48... 57 number keys
: 58 escape character for manufacturer specific keys
; 59 escape character for string entering
< 60 left arrow
> 62 right arrow
@ 64 alpha key (α/ABC)
A/a 65/97 channel A (A)
B/b 66/98 channel B (B)
C/c 67/99 clear display (C/CLR)
D/d 68/100 volume down
E/e 69/101 connection end (END)
F/f 70/102 function (FCN)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
108
3GPP TS 27.007 version 13.3.0 Release 13
Char
IRA (dec)
Comment (+ some known key symbols)
L/l 76/108 phone lock (LOCK)
M/m 77/109 menu (MENU)
P/p 80/112 power (PWR)
Q/q 81/113 quiet/mute (MUTE)
R/r 82/114 recall last number (R/RCL/MR)
S/s 83/115 connection start (SEND)
T/t 84/116 store/ memory (STO/M/M+)
U/u 85/117 volume up
V/v 86/118 down arrow
W/w 87/119 pause character
X/x 88/120 auxiliary (AUX)
Y/y 89/121 delete last character (C)
[ 91 soft key 1
] 93 soft key 2
^ 94 up arrow
<time>, <pause>: integer type
0...255 0... 25.5 seconds (default values are manufacturer specific, but should be so long that a normal MT
can handle keystrokes correctly)
Implementation
Mandatory for MT not supporting the +CPIN command and supporting AT commands only.
8.8 Display control +CDIS
Table 68: +CDIS parameter command syntax
Command
Possible response(s)
+CDIS=[<text>[,<text>[,...]]] +CME ERROR: <err>
+CDIS? +CDIS: <text>[,<text>[,...]]
+CME ERROR: <err>
+CDIS=? +CDIS: <length>[,<length>[,...]]
+CME ERROR: <err>
Description
Set command is used to write the contents of MT text type display elements. An element can consist of one character or
several characters. The order of element parameters <text> should follow the rule: first is the element in upper left
corner, second is the next element to the right and so on. The last element is the element in lower right corner. The
number of elements is MT specific. If MT does not allow writing to its display or MT is not currently reachable,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values. If certain element is not writable,
setting of it should be ignored. If element parameter is empty field, element shall remain in the previous value.
NOTE 1: This command cannot be used to write to a display which sum of element lengths exceed the length of the
command line buffer of the TA.
Read command returns the contents of MT display elements. If <text> field is empty (not empty string), MT does not
allow the reading of corresponding element. If MT is not currently reachable, +CME ERROR: <err> is returned.
Refer subclause 9.2 for possible <err> values.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
109
3GPP TS 27.007 versio
n 13.3.0 Release 13
Test command returns maximum length of each display element. If MT does not offer the length of elements,
<length> fields should be empty. If MT is not currently reachable, +CME ERROR: <err> is returned. Refer
subclause 9.2 for possible <err> values.
NOTE 2: MT manufacturer should offer the order and maximum length of elements.
Defined values
<text>: string type parameter using character set specified by command Select TE Character Set +CSCS
<length>: integer type parameter giving the maximum length of corresponding <text> parameter
Implementation
Optional.
8.9 Indicator control +CIND
Table 69: +CIND parameter command syntax
Command
Possible response(s)
+CIND=[<ind>[,<ind>[,...]]] +CME ERROR: <err>
+CIND? +CIND: <ind>[,<ind>[,...]]
+CME ERROR: <err>
+CIND=? +CIND: (<descr>,(list of supported
<ind>s))[,(<descr>,(list of supported
<ind>s))[,...]]
+CME ERROR: <err>
Description
Set command is used to set the values of MT indicators. <ind> value 0 means that the indicator is off (or in state
which can be identified as "off"-state), 1 means that indicator is on (or in a state which is more substantial than
"off"-state), 2 is more substantial than 1, and so on. If the indicator is a simple on/off style element, it has values 0 and
1. The number of elements is MT specific. If MT does not allow setting of indicators or MT is not currently reachable,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values. If certain indicator is not
writable, setting of it should be ignored. If parameter is empty field, indicator shall remain in the previous value.
Read command returns the status of MT indicators. If MT is not currently reachable, +CME ERROR: <err> is
returned. Refer subclause 9.2 for possible <err> values.
Test command returns pairs, where string value <descr> is a maximum 16 character description of the indicator and
compound value is the allowed values for the indicator. If MT is not currently reachable, +CME ERROR: <err> is
returned. Refer subclause 9.2 for possible <err> values.
NOTE: MT manufacturer should offer the description of supported indicators not listed here and their value
ranges and default values.
Defined values
<ind>: integer type value, which shall be in range of corresponding <descr>
<descr> values reserved by the present document and their <ind> ranges:
"battchg" battery charge level (0-5)
"signal" signal quality (0-5)
"service" service availability (0-1)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
110
3GPP TS 27.007 version 13.3.0 Release 13
"sounder" sounder activity (0-1)
"message" message received (0-1)
"call" call in progress (0-1)
"vox" transmit activated by voice activity (0-1)
"roam" roaming indicator (0-1)
"smsfull" a short message memory storage in the MT has become full and a short message has been
rejected (2), has become full (1), or memory locations are available (0); i.e. the range is (0-2)
"inputstatus" keypad/touch screen status (0-1)
Implementation
Optional.
8.10 Mobile termination event reporting +CMER
Table 70: +CMER parameter command syntax
Command
Possible response(s)
+CMER=[<mode>[,<keyp>[,<disp>
[,<ind>[,<bfr>[,<tscrn>][,<or
ientation>]]]]]]
+CME ERROR: <err>
+CMER? +CMER: <mode>,<keyp>,<disp>,<ind>,<bfr>,<tscr
n>,<orientation>
+CMER=?
+CMER: (list of supported <mode>s),(list of supported
<keyp>s),(list of supported <disp>s),(list of supported
<ind>s),(list of supported <bfr>s),(list of supported
<tscrn>s),(list of supported <orientation>s)
Description
Set command enables or disables sending of unsolicited result codes from TA to TE in the case of key pressings,
display changes, and indicator state changes. <mode> controls the processing of unsolicited result codes specified
within this command. <bfr> controls the effect on buffered codes when <mode> 1, 2 or 3 is entered. If setting is not
supported by the MT, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Read command returns the current settings.
Test command returns the modes supported as compound values.
Defined values
<mode>: integer type
0 buffer unsolicited result codes in the TA; if TA result code buffer is full, codes can be buffered in some other
place or the oldest ones can be discarded
1 discard unsolicited result codes when TA-TE link is reserved (e.g. in on-line data mode); otherwise forward
them directly to the TE
2 buffer unsolicited result codes in the TA when TA-TE link is reserved (e.g. in on-line data mode) and flush
them to the TE after reservation; otherwise forward them directly to the TE
3 forward unsolicited result codes directly to the TE; TA-TE link specific inband technique used to embed
result codes and data when TA is in on-line data mode
<keyp>: integer type
ETSI
ETSI TS 1
27 007 V13.3.0 (2016
-
03)
111
3GPP TS 27.007 version 13.3.0 Release 13
0 no keypad event reporting
1 keypad event reporting using unsolicited result code +CKEV: <key>,<press>. <key> indicates the key
(refer IRA values defined in table 67 in subclause "Keypad control +CKPD") and <press> if the key is
pressed or released (1 for pressing and 0 for releasing). Only those key pressings, which are not caused by
+CKPD shall be indicated by the TA to the TE.
NOTE 1: When this mode is enabled, corresponding result codes of all keys currently pressed are flushed to the TA
regardless of <bfr> setting.
2 keypad event reporting using unsolicited result code +CKEV: <key>,<press>. All key pressings shall be
directed from TA to TE.
NOTE 2: When this mode is enabled, corresponding result codes of all keys currently pressed are flushed to the TA
regardless of <bfr> setting.
<disp>: integer type
0 no display event reporting
1 display event reporting using unsolicited result code +CDEV: <elem>,<text>. <elem> indicates the
element order number (as specified for +CDIS) and <text> is the new value of text element. Only those
display events, which are not caused by +CDIS shall be indicated by the TA to the TE. Character set used in
<text> is as specified by command Select TE Character Set +CSCS
2 display event reporting using unsolicited result code +CDEV: <elem>,<text>. All display events shall
be directed from TA to TE. Character set used in <text> is as specified by command Select TE Character
Set +CSCS
<ind>: integer type
0 no indicator event reporting
1 indicator event reporting using unsolicited result code +CIEV: <ind>,<value>. <ind> indicates the
indicator order number (as specified for +CIND) and <value> is the new value of indicator. Only those
indicator events, which are not caused by +CIND shall be indicated by the TA to the TE
2 indicator event reporting using unsolicited result code +CIEV: <ind>,<value>. All indicator events
shall be directed from TA to TE
<bfr>: integer type
0 TA buffer of unsolicited result codes defined within this command is cleared when <mode> 1...3 is entered
1 TA buffer of unsolicited result codes defined within this command is flushed to the TE when <mode> 1...3
is entered (OK response shall be given before flushing the codes)
<tscrn>: integer type
0 no touch screen event reporting
1 touch screen event reporting using unsolicited result code +CTEV: <action>,<x>,<y>. The <x>,<y>
parameters indicate the x, y coordinates on the touch screen device (as specified for +CTSA), and
<action> indicates the action performed on the screen (0 for screen released, 1 for screen depressed, 2 for
single tap, and 3 for double tap). Only those touch screen events, which are not caused by +CTSA shall be
indicated by the TA to the TE.
NOTE 3: When this mode is enabled, corresponding result codes of all touch screen actions are flushed to the TA
regardless of <bfr> setting.
2 touch screen event reporting using unsolicited result code +CTEV: <action>,<x>,<y>. All touch
screen events shall be directed from the TA to the TE.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
112
3GPP TS 27.007 version 13.3.0 Release 13
NOTE 4: When this mode is enabled, corresponding result codes of all touch screen actions are flushed to the TA
regardless of <bfr> setting.
3 Verbose mode. Touch screen event reporting using unsolicited result code
+CTEV: <action>,<x>,<y>. This is a special mode where intermediate depressed result codes
(+CTEV: 1,<x>,<y>) are generated for each new <x>,<y> coordinate detected while a user is dragging a
touch to a new location. All other touch screen actions shall be directed from the TA to the TE normally.
Only those touch screen events which are not caused by +CTSA shall be indicated by the TA to the TE.
NOTE 5: When this mode is enabled, corresponding result codes of all touch screen actions are flushed to the TA
regardless of <bfr> setting.
4 enchanced touch screen event reporting using unsolicited result code
+CTEV: <action>,<x>,<y>,<id>[,<duration>]. The <x>,<y> parameters indicate the x, y
coordinates on the touch screen device (as specified for +CTSA), the <duration> parameter indicates the
duration of the touch (as specified for +CTSA) and, the <id> identifies any simultaneous touch (as specified
for +CTSA). Only those touch screen events, which are not caused by +CTSA shall be indicated by the TA to
the TE. The <action> parameter indicates the action performed on the screen, if the <duration>
parameter is:
- 0, it is valid for the <action> parameter to indicate 0 for screen released, 1 for screen depressed, 2 for
single tap, and 3 for double tap;
- a positive, non-zero integer, it is valid for the <action> parameter to indicate 0 for screen released.
NOTE 6: When this mode is enabled, corresponding result codes of all touch screen actions are flushed to the TA
regardless of <bfr> setting.
5 enchanced touch screen event reporting using unsolicited result code
+CTEV: <action>,<x>,<y>,<id>[,<duration>]. See description of <tscrn> set to 4 for the
valid for the <action> parameter. All touch screen events shall be directed from the TA to the TE.
NOTE 7: When this mode is enabled, corresponding result codes of all touch screen actions are flushed to the TA
regardless of <bfr> setting.
6 Verbose mode. enchanced touch screen event reporting using unsolicited result code
+CTEV: <action>,<x>,<y>,<id>[,<duration>]. This is a special mode where intermediate
depressed result codes (+CTEV: 1,<x>,<y>,<id>[,<duration>]) are generated for each new
<x>,<y> coordinate detected while a user is dragging a touch to a new location. All other touch screen
actions shall be directed from the TA to the TE normally. See description of <tscrn> set to 4 for the valid
for the <action> parameter. Only those touch screen events which are not caused by +CTSA shall be
indicated by the TA to the TE.
NOTE 8: When this mode is enabled, corresponding result codes of all touch screen actions are flushed to the TA
regardless of <bfr> setting.
<orientation>: integer type: Parameter to enable display orientation event reporting from the TA to the TE,
using unsolicited result code +COEV: <CurrentTopSide>. The <CurrentTopSide> parameter
indicates the top of the ME's screen (as specified for +CSO).
0 No display orientation event reporting.
1 Only those display orientation events, which are not caused by +CSO shall be indicated.
2 All display orientation events shall be indicated.
Implementation
Mandatory when any of the keypad, display, or indicator, or touch screen result codes is implemented.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
113
3GPP TS 27.007 version 13.3.0 Release 13
8.11 Select phonebook memory storage +CPBS
Table 71: +CPBS parameter command syntax
Command
Possible response(s)
+CPBS=<storage>[,<password>] +CME ERROR: <err>
+CPBS? +CPBS: <storage>[,<used>,<total>]
+CME ERROR: <err>
+CPBS=?
+CPBS: (list of supported <storage>s)
Description
Set command selects phonebook memory storage <storage>, which is used by other phonebook commands. If
setting fails in an MT error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Read command returns currently selected memory, and when supported by manufacturer, number of used locations and
total number of locations in the memory.
Test command returns supported storages as a compound value.
Defined values
<storage> values reserved by the present document:
"DC" MT dialled calls list (+CPBW may not be applicable for this storage)
"EN" SIM/USIM (or MT) emergency number (+CPBW is not be applicable for this storage)
"FD" SIM/USIM fixdialling-phonebook. In the currently selected card slot, if a SIM card is present or if a
UICC with an active GSM application is present, the information in EF
FDN
under DF
Telecom
is selected.
If a UICC with an active USIM application is present, the information in EF
FDN
under ADF
USIM
is
selected.
"LD" SIM/UICC last-dialling-phonebook
"MC" MT missed (unanswered received) calls list (+CPBW may not be applicable for this storage)
"ME" MT phonebook
"MT" combined MT and SIM/USIM phonebook
"ON" SIM (or MT) own numbers (MSISDNs) list (reading of this storage may be available through +CNUM
also). When storing information in the SIM/UICC, if a SIM card is present or if a UICC with an active
GSM application is present, the information in EF
MSISDN
under DF
Telecom
is selected. If a UICC with an
active USIM application is present, the information in EF
MSISDN
under ADF
USIM
is selected.
"RC" MT received calls list (+CPBW may not be applicable for this storage)
"SM" SIM/UICC phonebook. In the currently selected card slot, if a SIM card is present or if a UICC with
an active GSM application is present, the EF
ADN
under DF
Telecom
is selected. If a UICC with an active
USIM application is present, the global phonebook, DF
PHONEBOOK
under DF
Telecom
is selected.
"TA" TA phonebook
"AP" Selected application phonebook. In the currently selected card slot, if a UICC with an active USIM
application is present, the application phonebook, DF
PHONEBOOK
under ADF
USIM
is selected.
<password>: string type value representing the PIN2-code required when selecting PIN2-code locked
<storage>s above, e.g. "FD" or the hidden key to be verified in order to access to the hidden phonebook
entries in the UICC/USIM or any other phonebook with hidden entries.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
114
3GPP TS 27.007 version 13.3.0
Release 13
If the combined phonebook is selected, "MT", the <password> will correspond to the hidden key of the USIM
phonebook.
<used>: integer type value indicating the number of used locations in selected memory
<total>: integer type value indicating the total number of locations in selected memory
Implementation
Mandatory when phonebook read, find or write command, or direct dialling (refer subclause "Direct dialling from
phonebooks") is implemented.
8.12 Read phonebook entries +CPBR
Table 72: +CPBR action command syntax
Command
Possible response(s)
+CPBR=<index1>[,<i
ndex2>] [+CPBR: <index1>,<number>,<type>,<text>[,<hidden>][,<gro
up>][,<adnumber>][,<adtype>][,<secondtext>][,<email>][,<
sip_uri>][,<tel_uri>]]
[[...]
[<CR><LF>+CPBR: <index2>,<number>,<type>,<text>[,<hidden
>][,<group>][,<adnumber>][,<adtype>][,<secondtext>][,<em
ail>][,<sip_uri>][,<tel_uri>]]]
+CME ERROR: <err>
+CPBR=?
+CPBR: (list of supported
<index>s),[<nlength>],[<tlength>],[<glength>],[<slength>
],[<elength>],[<siplength>],[<tellength>]
+CME ERROR: <err>
Description
Execution command returns phonebook entries in location number range <index1>... <index2> from the current
phonebook memory storage selected with +CPBS. If <index2> is left out, only location <index1> is returned. Entry
fields returned are location number <indexn>, phone number stored there <number> (of format <type>), text
<text> associated with the number, if the selected phonebook supports hidden entries, <hidden> indicating if the
entry is hidden, <group> indicating a group the entry may belong to, <adnumber> an additional number (of
format <adtype>), <secondtext> a second text field associated with the number, <email> an email field,
<sip_uri> SIP number and <tel_uri> TEL number. If all queried locations are empty (but available), no
information text lines may be returned. If listing fails in an MT error, +CME ERROR: <err> is returned. Refer
subclause 9.2 for possible <err> values.
Test command returns location range supported by the current storage as a compound value and the maximum lengths
of <number>, <text>, <group>, <secondtext>, <email>, <sip_uri> and <tel_uri> fields. In case of
(U)SIM storage, the lengths may not be available. If MT is not currently reachable, +CME ERROR: <err> is
returned. Refer subclause 9.2 for possible <err> values.
Defined values
<index1>, <index2>, <index>: integer type values in the range of location numbers of phonebook memory
<number>: string type phone number of format <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<text>: string type field of maximum length <tlength>; character set as specified by command Select TE
Character Set +CSCS
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
115
3GPP TS 27.007 version 13.3.0 Release 13
<group>: string type field of maximum length <glength>; character set as specified by command Select TE
Character Set +CSCS
<adnumber>: string type phone number of format <adtype>
<adtype>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<secondtext>: string type field of maximum length <slength>; character set as specified by command Select
TE Character Set +CSCS
<email>: string type field of maximum length <elength>; character set as specified by command Select TE
Character Set +CSCS
<sip_uri>: string type field of maximum length <siplength>; character set as specified by command Select
TE Character Set +CSCS
<tel_uri>: string type phone number of maximum length <tellength>; character set as specified by
command Select TE Character Set +CSCS
<nlength>: integer type value indicating the maximum length of field <number>
<tlength>: integer type value indicating the maximum length of field <text>
<glength>: integer type value indicating the maximum length of field <group>
<slength>: integer type value indicating the maximum length of field <secondtext>
<elength>: integer type value indicating the maximum length of field <email>
<siplength>: integer type value indicating the maximum length of field <sip_uri>
<tellength>: integer type value indicating the maximum length of field <tel_uri>
<hidden>: integer type value indicates if the entry is hidden or not
0: phonebook entry not hidden
1: phonebook entry hidden
Implementation
Optional.
8.13 Find phonebook entries +CPBF
Table 73: +CPBF action command syntax
Command
Possible response(s)
+CPBF=<findtext>
[+CPBF: <index1>,<number>,<type>,<text>[,<hidden>][,<group>
][,<adnumber>][,<adtype>][,<secondtext>][,<email>][,<sip_ur
i>][,<tel_uri>]]
[<CR><LF>+CBPF: <index2>,<number>,<type>,<text>[,<hidden>][
,<group>][,<adnumber>][,<adtype>][,<secondtext>][,<email>][
,<sip_uri>][,<tel_uri>]
[...]]
+CME ERROR: <err>
+CPBF=?
+CPBF: [<nlength>],[<tlength>],[<glength>],[<slength>],[<el
ength>],[<siplength>],[<tellength>]
+CME ERROR: <err>
ETSI
ETSI TS 127 007 V
13.3.0 (2016
-
03)
116
3GPP TS 27.007 version 13.3.0 Release 13
Description
Execution command returns phonebook entries (from the current phonebook memory storage selected with +CPBS)
which alphanumeric field start with string <findtext>. Entry fields returned are location number <indexn>, phone
number stored there <number> (of format <type>), text <text> associated with the number, if the selected
phonebook supports hidden entries, <hidden> indicating if the entry is hidden, <group> indicating a group the entry
may belong to, <adnumber> an additional number (of format <adtype>), <secondtext> a second text field
associated with the number, <email> an email field, <sip_uri> SIP number and <tel_uri> TEL number. If
listing fails in an MT error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Test command returns the maximum lengths of <number>, <text>, <group>, <secondtext>, <email>,
<sip_uri> and <tel_uri> fields. In case of (U)SIM storage, the lengths may not be available. If MT is not
currently reachable, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Defined values
<index1>, <index2>: integer type values in the range of location numbers of phonebook memory
<number>: string type phone number of format <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<group>: string type field of maximum length <glength>; character set as specified by command Select TE
Character Set +CSCS
<adnumber>: string type phone number of format <adtype>
<adtype>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<secondtext>: string type field of maximum length <slength>; character set as specified by command Select
TE Character Set +CSCS
<email>: string type field of maximum length <elength>; character set as specified by command Select TE
Character Set +CSCS
<findtext>, <text>: string type field of maximum length <tlength>; character set as specified by command
Select TE Character Set +CSCS
<sip_uri>: string type field of maximum length <siplength>; character set as specified by command Select
TE Character Set +CSCS
<tel_uri>: string type phone number of maximum length <tellength>; character set as specified by
command Select TE Character Set +CSCS
<nlength>: integer type value indicating the maximum length of field <number>
<tlength>: integer type value indicating the maximum length of field <text>
<glength>: integer type value indicating the maximum length of field <group>
<slength>: integer type value indicating the maximum length of field <secondtext>
<elength>: integer type value indicating the maximum length of field <email>
<siplength>: integer type value indicating the maximum length of field <sip_uri>
<tellength>: integer type value indicating the maximum length of field <tel_uri>
<hidden>: integer type value indicates if the entry is hidden or not
0: phonebook entry not hidden
1: phonebook entry hidden
Implementation
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
117
3GPP TS 27.007 version 13.3.0 Release 13
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
118
3GPP TS 27.007 version 13.3.0 Release 13
8.14 Write phonebook entry +CPBW
Table 74: +CPBW parameter command syntax
Command
Possible response(s)
+CPBW=[<index>][,<number>[,<t
ype>[,<text>[,<group>[,<adnum
ber>[,<adtype>[,<secondtext>[
,<email>[,<sip_uri>[,<tel_uri
>[,<hidden>]]]]]]]]]]]
+CPBW: <written_index>
+CME ERROR: <err>
+CPBW? +CPBW: <written_index>
+CPBW=?
+CPBW: (list of supported <index>s),[<nlength>],(
list of
supported
<type>s),[<tlength>],[<glength>],[<slength>],[
<elength>],[<siplength>],[<tellength>]
+CME ERROR: <err>
Description
Execution command writes phonebook entry in location number <index> in the current phonebook memory storage
selected with +CPBS. Entry fields written are phone number <number> (in the format <type>), text <text>
associated with the number, if the selected phonebook supports hidden entries, <hidden> parameter, which indicates if
the entry is hidden or not, <group> indicating a group the entry may belong to, <adnumber> an additional
number (of format <adtype>), <secondtext> a second text field associated with the number, <email> an
email field, <sip_uri> SIP number and <tel_uri> TEL number. If all those fields are omitted, the phonebook
entry is deleted. If <index> is left out, but <number> is given, the entry is written to the first free location in the
phonebook (the implementation of this feature is manufacturer specific). For successfull writes where <index> is not
given, the intermediate result code +CPBW: <written_index> may be provded to indicate the location the entry
was written to. If writing fails in an MT error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible
<err> values.
Read command returns the last <written_index> value, or -1 if information about previous value is not available.
NOTE: Changing the current phonebook memory storage with +CPBS to another storage invalidates the last
<written_index> value.
Test command returns location range supported by the current storage and types of address as compound values, the
maximum length of <number> field, supported number formats of the storage, the maximum length of <text> field,
the maximum length of <group>, the maximum length of <secondtext>, the maximum length of <email>, the
maximum length of <sip_uri> and the maximum length of <tel_uri>. In case of SIM storage, the lengths may
not be available. If MT is not currently reachable, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible
<err> values. If storage does not offer format information, the format list should be empty parenthesis.
Defined values
<index>: integer type values in the range of location numbers of phonebook memory
<number>: string type phone number of format <type>
<type>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7) ; default 145 when
dialling string includes international access code character "+", otherwise 129
<text>: string type field of maximum length <tlength>; character set as specified by command Select TE
Character Set +CSCS
<group>: string type field of maximum length <glength>; character set as specified by command Select TE
Character Set +CSCS
<adnumber>: string type phone number of format <adtype>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
119
3GPP TS 27.007 version 13.3.0 Release
13
<adtype>: type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7)
<secondtext>: string type field of maximum length <slength>; character set as specified by command Select
TE Character Set +CSCS
<email>: string type field of maximum length <elength>; character set as specified by command Select TE
Character Set +CSCS
<sip_uri>: string type field of maximum length <siplength>; character set as specified by command Select
TE Character Set +CSCS
<tel_uri>: string type phone number of maximum length <tellength>; character set as specified by
command Select TE Character Set +CSCS
<nlength>: integer type value indicating the maximum length of field <number>
<tlength>: integer type value indicating the maximum length of field <text>
<glength>: integer type value indicating the maximum length of field <group>
<slength>: integer type value indicating the maximum length of field <secondtext>
<elength>: integer type value indicating the maximum length of field <email>
<siplength>: integer type value indicating the maximum length of field <sip_uri>
<tellength>: integer type value indicating the maximum length of field <tel_uri>
<hidden>: integer type value indicates if the entry is hidden or not
0: phonebook entry not hidden
1: phonebook entry hidden
<written_index>: integer type value indicating the last location number <index> of the written phonebook
entry
Implementation
Optional.
8.15 Clock +CCLK
Table 75: +CCLK parameter command syntax
Command
Possible response(s)
+CCLK=<time> +CME ERROR: <err>
+CCLK? +CCLK: <time>
+CME ERROR: <err>
+CCLK=?
Description
Set command sets the real-time clock of the MT. If setting fails in an MT error, +CME ERROR: <err> is returned.
Refer subclause 9.2 for possible <err> values.
Read command returns the current setting of the clock.
Defined values
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
120
3GPP TS 27.007 version 13.3.0 Release 13
<time>: string type value; format is "yy/MM/dd,hh:mm:ss±zz", where characters indicate year (two last digits),
month, day, hour, minutes, seconds and time zone (indicates the difference, expressed in quarters of an hour,
between the local time and GMT; range -96...+96). E.g. 6th of May 1994, 22:10:00 GMT+2 hours equals to
"94/05/06,22:10:00+08"
NOTE: If MT does not support time zone information then the three last characters of <time> are not returned
by +CCLK?. The format of <time> is specified by use of the +CSDF command.
Implementation
Optional.
8.16 Alarm +CALA
Table 76: +CALA parameter command syntax
Command
Possible response(s)
+CALA=<time>[,<n>[,<type>[,
<text>[,<recurr>[,<silent>]
]]]]
+CME ERROR: <err>
+CALA? [+CALA: <time>,<n1>,<type>,[<text>],[<recurr>]
,<silent>]
[<CR><LF>+CALA: <time>,<n2>,<type>,[<text>],[<
recurr>],<silent>
[...]]
+CME ERROR: <err>
+CALA=?
+CALA: (list of supported <n>s),(list of supported
<type>s),<tlength>,<rlength>,(list of supported
<silent>s)
+CME ERROR: <err>
Description
Set command sets an alarm time in the MT. There can be an array of different types of alarms, and each alarm may
cause different text to be displayed in the MT display. If setting fails in an MT error, +CME ERROR: <err> is
returned. Refer subclause 9.2 for possible <err> values.
To set up a recurrent alarm for one or more days in the week, the <recurr>-parameter may be used.
When an alarm is timed out and executed, the unsolicited result code +CALV: <n> is always returned, even if the
alarm is set up to be silent.
Read command returns the list of current active alarm settings in the MT.
Test command returns supported array index values, alarm types, and maximum length of the text to be displayed as
compound values.
Defined values
<time>: refer +CCLK,+CSDF
NOTE: If the <recurr>-parameter is used, the <time>-parameter must not contain a date.
<n>, <n1>, <n2>: integer type value indicating the index of the alarm; default is manufacturer specific
<type>: integer type value indicating the type of the alarm (e.g. sound, volume, LED); values and default are
manufacturer specific.
ETSI
ETSI TS 127 007 V13.3.0 (
2016
-
03)
121
3GPP TS 27.007 version 13.3.0 Release 13
<text>: string type value indicating the text to be displayed when alarm time is reached; maximum length
<tlength>; values and default are manufacturer specific.
<tlength>: integer type value indicating the maximum length of <text>
<recurr>: string type value indicating day of week for the alarm in one of the following formats (values and
default are manufacturer specific):
"<1..7>[,<1..7>[…]]" Sets a recurrent alarm for one or more days in the week. The digits 1 to 7
corresponds to the days in the week, Monday (1), …, Sunday (7).
Example: The string "1,2,3,4,5" is used to set an alarm for all weekdays.
"0" Sets a recurrent alarm for all days in the week.
<rlength>: integer type value indicating the maximum length of <recurr>
<silent>: Integer type value indicating if the alarm is silent or not. The defalt value is manufacturer specific.
0 the alarm will not be silent
1 the alarm will be silent and the only result from the alarm is the unsolicited result code +CALV
Implementation
Optional.
8.17 Generic SIM access +CSIM
Table 77: +CSIM action command syntax
Command
Possible response(s)
+CSIM=<length>,<command> +CSIM: <length>,<response>
+CME ERROR: <err>
+CSIM=?
Description
Set command transmits to the MT the <command> it then shall send as it is to the SIM. In the same manner, the SIM
<response> shall be sent back by the MT to the TA as it is. Refer subclause 9.2 for possible <err> values.
This command allows a direct control of the SIM that is installed in the currently selected card slot, by an distant
application on the TE. The TE shall then take care of processing SIM information within the frame specified by
GSM/UMTS.
NOTE: Compared to Restricted SIM Access command +CRSM, the definition of +CSIM allows TE to take more
control over the SIM-MT interface. The locking and unlocking of the interface may be done by a special
<command> value or automatically by TA/MT (by interpreting <command> parameter). In case that TE
application does not use the unlock command (or does not send a <command> causing automatic
unlock) in a certain timeout value, MT may release the locking.
Defined values
<length>: integer type; length of the characters that are sent to TE in <command> or <response> (two times
the actual length of the command or response)
<command>: command passed on by the MT to the SIM in the format as described in 3GPP TS 51.011 [28]
(hexadecimal character format; refer +CSCS)
<response>: response to the command passed on by the SIM to the MT in the format as described in
3GPP TS 51.011 [28] (hexadecimal character format; refer +CSCS)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
122
3GPP TS 27.007 version 13.3.0 Release 13
Implementation
Optional.
8.18 Restricted SIM access +CRSM
Table 78: +CRSM action command syntax
Command
Possible response(s)
+CRSM=<command>[,<fileid>[,<P
1>,<P2>,<P3>[,<data>[,<pathid
>]]]]
+CRSM: <sw1>,<sw2>[,<response>]
+CME ERROR: <err>
+CRSM=?
Description
By using this command instead of Generic SIM Access +CSIM TE application has easier but more limited access to the
SIM database. Set command transmits to the MT the SIM <command> and its required parameters. If a SIM installed
in the currently selected card slot, the MT handles internally all SIM-MT interface locking and file selection routines.
As response to the command, MT sends the actual SIM information parameters and response data. MT error result code
+CME ERROR may be returned when the command cannot be passed to the SIM, but failure in the execution of the
command in the SIM is reported in <sw1> and <sw2> parameters. Refer subclause 9.2 for possible <err> values.
Coordination of command requests to SIM and the ones issued by GSM/UMTS application inside the MT is
implementation dependent. However the TE should be aware of the precedence of the GSM/UMTS application
commands to the TE commands.
Defined values
<command>: (command passed on by the MT to the SIM; refer 3GPP TS 51.011 [28]):
176 READ BINARY
178 READ RECORD
192 GET RESPONSE
214 UPDATE BINARY
220 UPDATE RECORD
242 STATUS
203 RETRIEVE DATA
219 SET DATA
all other values are reserved
NOTE 1: The MT internally executes all commands necessary for selecting the desired file, before performing the
actual command.
<fileid>: integer type; this is the identifier of a elementary datafile on SIM. Mandatory for every command
except STATUS
NOTE 2: The range of valid file identifiers depends on the actual SIM and is defined in 3GPP TS 51.011 [28].
Optional files may not be present at all.
<P1>, <P2>, <P3>: integer type; parameters passed on by the MT to the SIM. These parameters are mandatory for
every command, except GET RESPONSE and STATUS. The values are described in 3GPP TS 51.011 [28]
<data>: information which shall be written to the SIM (hexadecimal character format; refer +CSCS)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
123
3GPP TS 27.007 version 13.3.0 Release 13
<pathid>: string type; contains the path of an elementary file on the SIM/UICC in hexadecimal format as defined
in ETSI TS 102 221 [60] (e.g. "7F205F70" in SIM and UICC case). The <pathid> shall only be used in the
mode "select by path from MF" as defined in ETSI TS 102 221 [60].
NOTE 3: Since valid elementary file identifiers may not be unique over all valid dedicated file identifiers the
<pathid> indicates the targeted UICC/SIM directory path in case of ambiguous file identifiers. For
earlier versions of this specification or if <pathid> is omitted, it could be implementation specific
which one will be selected.
<sw1>, <sw2>: integer type; information from the SIM about the execution of the actual command. These
parameters are delivered to the TE in both cases, on successful or failed execution of the command
<response>: response of a successful completion of the command previously issued (hexadecimal character
format; refer +CSCS). STATUS and GET RESPONSE return data, which gives information about the current
elementary datafield. This information includes the type of file and its size (refer 3GPP TS 51.011 [28]). After
READ BINARY, READ RECORD or RETRIEVE DATA command the requested data will be returned.
<response> is not returned after a successful UPDATE BINARY, UPDATE RECORD or SET DATA
command.
Implementation
Optional.
8.19 Secure control command +CSCC
Table 79: +CSCC parameter command syntax
Command
Possible response(s)
+CSCC=<mode>[,<cmd_set>[,
<token>]] +CSCC: <challenge>
+CME ERROR: <err>
+CSCC? +CSCC: <mode>,<cmd_set1>
[<CR><LF>+CSCC: <mode>,<cmd_set2>
[...]]
+CME ERROR: <err>
+CSCC=?
+CSCC: (list of supported <mode>s),(list of supported
<cmd_set>s)
Description
This command is used to enable/disable access to commands protected by security mechanism. This enables/disables
access to command sets designated as "secure" such as programming of MT. Refer subclause 9.2 for possible <err>
values.
The TE asks for a <challenge> with <mode>=1 and one specific command set (<cmd_set>), the MT replies with
the <challenge>, which should be inserted into the identification algorithm in both entities (TE and MT). The
algorithm output <token> is sent to the MT with <mode>=2 to enable the specified command set. <mode>=3 is used
to disable the command set.
The read command returns the status (<mode> 2 or 3) of each supported command set.
Test command returns the values supported as compound values.
Defined values
<mode>: integer type
1 request challenge token to enable access to specified command set
2 enable access to specified command set (<token> required)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
124
3GPP TS 27.007 version 13.3.0 Release 13
3 disable access to specified command set
<cmd_set>, <cmd_set1>, <cmd_set2>:
0 MT/TA code re-programming command set.
other values below 128 are reserved by the present document
<token>: string type; a variable length bit string represented with IRA characters 0 - 9 and A - F, each character
representing a nibble; e.g. bit string "0110 1100 1001 1010" is represented by the IRA string "6C9A". The length
of the required bit string varies depending on the value of <cmd_set>.
<challenge>: same format as token
Implementation
Optional.
8.20 Alert sound mode +CALM
Table 80: +CALM parameter command syntax
Command
Possible response(s)
+CALM=[<mode>]
+CME ERROR: <err>
+CALM? +CALM: <mode>
+CME ERROR: <err>
+CALM=?
+CALM: (list of supported <mode>s)
+CME ERROR: <err>
Description
This command is used to select the general alert sound mode of the MT. Refer subclause 9.2 for possible <err>
values.
Read command returns the current value of <mode>.
Test command returns supported values as a compound value.
Defined values
<mode>: integer type
0 normal mode
1 silent mode (all sounds from MT are prevented)
2… manufacturer specific
Implementation
Optional.
8.21 Ringer sound level +CRSL
Table 81: +CRSL parameter command syntax
Command
Possible response(s)
+CRSL=<level>
+CME ERROR: <err>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
125
3GPP TS 27.007 version 13.3.0 Release 13
+CRSL? +CRSL: <level>
+CME ERROR: <err>
+CRSL=?
+CRSL: (list of supported <level>s)
+CME ERROR: <err>
Description
This command is used to select the incoming call ringer sound level of the MT. Refer subclause 9.2 for possible
<err> values.
Read command returns the current value of <level>.Test command returns supported values as a compound value.
Defined values
<level>: integer type value with manufacturer specific range (smallest value represents the lowest sound level)
Implementation
Optional.
8.22 Vibrator mode +CVIB
Table 82: +CVIB parameter command syntax
Command
Possible response(s)
+CVIB=[<mode>]
+CME ERROR: <err>
+CVIB? +CVIB: <mode>
+CME ERROR: <err>
+CVIB=?
+CVIB: (list of supported <mode>s)
+CME ERROR: <err>
Description
This command is used to enable and disable the vibrator alert feature of the MT. It is manufacturer specific how this
interacts with +CALM command. Refer subclause 9.2 for possible <err> values.
Read command returns the current value of <mode>.
Test command returns supported values as a compound value.
Defined values
<mode>: integer type
0 disable
1 enable
...15 reserved by the present document
16… manufacturer specific
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
126
3GPP TS 27.007 version 13.3.0 Release 13
8.23 Loudspeaker volume level +CLVL
Table 83: +CLVL parameter command syntax
Command
Possible response(s)
+CLVL=<level>
+CME ERROR: <err>
+CLVL? +CLVL: <level>
+CME ERROR: <err>
+CLVL=?
+CLVL: (list of supported <level>s)
+CME ERROR: <err>
Description
This command is used to select the volume of the internal loudspeaker of the MT. Refer subclause 9.2 for possible
<err> values.
Read command returns the current value of <level>.
Test command returns supported values as a compound value.
Defined values
<level>: integer type value with manufacturer specific range (smallest value represents the lowest sound level)
Implementation
Optional.
8.24 Mute control +CMUT
Table 84: +CMUT parameter command syntax
Command
Possible response(s)
+CMUT=[<n>]
+CME ERROR: <err>
+CMUT? +CMUT: <n>
+CME ERROR: <err>
+CMUT=?
+CMUT: (list of supported <n>s)
Description
This command is used to enable and disable the uplink voice muting during a voice call. Refer subclause 9.2 for
possible <err> values.
Read command returns the current value of <n>.
Test command returns supported values as a compound value.
Defined values
<n>: integer type
0 mute off
1 mute on
Implementation
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
127
3GPP TS 27.007 version 13.3.0 Release 13
Optional.
8.25 Accumulated call meter +CACM
Table 85: +CACM parameter command syntax
Command
Possible response(s)
+CACM=[<passwd>] +CME ERROR: <err>
+CACM? +CACM: <acm>
+CME ERROR: <err>
+CACM=?
Description
Set command resets the Advice of Charge related accumulated call meter value in SIM card or in the active application
in the UICC (GSM or USIM) file EF
ACM
. ACM contains the total number of home units for both the current and
preceding calls. SIM PIN2 is usually required to reset the value. If setting fails in an MT error,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Read command returns the current value of ACM.
Defined values
<passwd>: string type; SIM PIN2
<acm>: string type; accumulated call meter value similarly coded as <ccm> under +CAOC
Implementation
Optional.
8.26 Accumulated call meter maximum +CAMM
Table 86: +CAMM parameter command syntax
Command
Possible response(s)
+CAMM=[<acmmax>[,<passwd>]] +CME ERROR: <err>
+CAMM? +CAMM: <acmmax>
+CME ERROR: <err>
+CAMM=?
Description
Set command sets the Advice of Charge related accumulated call meter maximum value in SIM card or in the active
application in the UICC (GSM or USIM) file EF
ACMmax
. ACMmax contains the maximum number of home units
allowed to be consumed by the subscriber. When ACM (refer +CACM) reaches ACMmax calls are prohibited (see also
3GPP TS 22.024 [26]). SIM PIN2 is usually required to set the value. If setting fails in an MT error,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Read command returns the current value of ACMmax.
Defined values
<acmmax>: string type; accumulated call meter maximum value similarly coded as <ccm> under +CAOC; value
zero disables ACMmax feature
<passwd>: string type; SIM PIN2
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
128
3GPP TS 27.007 version 13.3.0 Release 13
Implementation
Optional.
8.27 Price per unit and currency table +CPUC
Table 87: +CPUC parameter command syntax
Command
Possible response(s)
+CPUC=<currency>,<ppu>[,<passwd>] +CME ERROR: <err>
+CPUC? +CPUC: <currency>,<ppu>
+CME ERROR: <err>
+CPUC=?
Description
Set command sets the parameters of Advice of Charge related price per unit and currency table in SIM card or in the
active application in the UICC (GSM or USIM) file EF
PUCT
. PUCT information can be used to convert the home units
(as used in +CAOC, +CACM and +CAMM) into currency units. SIM PIN2 is usually required to set the parameters. If
setting fails in an MT error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Read command returns the current parameters of PUCT.
Defined values
<currency>: string type; three-character currency code (e.g. "GBP", "DEM"); character set as specified by
command Select TE Character Set +CSCS
<ppu>: string type; price per unit; dot is used as a decimal separator (e.g. "2.66")
<passwd>: string type; SIM PIN2
Implementation
Optional.
8.28 Call meter maximum event +CCWE
Table 88: +CCWE parameter command syntax
Command
Possible response(s)
+CCWE=[<mode>] +CME ERROR: <err>
+CCWE? +CCWE: <mode>
+CME ERROR: <err>
+CCWE=?
+CCWE: (list of supported <mode>s)
+CME ERROR: <err>
Description
Shortly before the ACM (Accumulated Call Meter) maximum value is reached, an unsolicited result code +CCWV will
be sent, if enabled by this command. The warning is issued approximately when 30 seconds call time remains. It is also
issued when starting a call if less than 30 s call time remains. If setting fails in an MT error, +CME ERROR: <err>
is returned. Refer subclause 9.2 for possible <err> values.
Read command returns the current setting.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
129
3GPP TS 27.007 version 13.3.0 Release 13
Test command returns supported settings as a compound value.
Defined values
<mode>: integer type
0 Disable the call meter warning event
1 Enable the call meter warning event
Implementation
Optional.
8.29 Power class +CPWC
Table 89: +CPWC parameter command syntax
Command
Possible response(s)
+CPWC=[<class>[,<band>]] +CME ERROR: <err>
+CPWC? +CPWC: <curr_class1>,<def_class1>,
<band1>[,<curr_class2>,<def_class2
>,<band2>[...]]
+CME ERROR: <err>
+CPWC=?
+CPWC: list of supported (<band>,(list of
<class>s)) pairs
+CME ERROR: <err>
Description
This command is used to set the preferred MT power class for each GSM frequency band supported. The interaction of
this setting with the selected bearer service (+CBST and HSCSD commands) is manufacturer specific (for example,
selecting a multislot operation might reduce the power class automatically). If setting fails in an MT error,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Read command returns the currently selected output power class and default output power class for each supported
frequency band (as defined by MT manufacturer). Parameter <band1> and its associated power class parameters refer
to the currently used frequency band.
Example: +CPWC: 2,1,1,5,4,0 indicates a dual-band MT currently using band GSM1800, for which
the power class is currently set to 2, the default being class 1, and for which the currently set
power class value for GSM900 is class 5 the default being class 4.
Test command returns supported bands and their power classes as compound values.
Example: +CPWC: (0,(0,4,5)),(1,(0-2)) indicates a dual-band handheld MT.
Defined values
<class>, <curr_classn>s, <def_classn>s: integer type
0 default (not applicable to <curr_class>s or <def_classn>s)
1… MT output power class as in 3GPP TS 45.005 [38]
<band>, <bandn>s:
0 GSM900
1 GSM1800
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
130
3GPP TS 27.007 version 13.3.0 Release 13
2 reserved for GSM1900
3 GSM 400
Implementation
Optional.
8.30 Set language +CLAN
Table 90: +CLAN parameter command syntax
Command
Possible response(s)
+CLAN=<code> +CME ERROR: <err>
+CLAN? +CLAN: <code>
+CME ERROR: <err>
+CLAN=?
+CLAN: (list of supported <code>s)
+CME ERROR: <err>
Description
This command sets the language in the MT. The set-command must confirm the selected language with the MMI-
module in the MT. If setting fails, a MT error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible
<err> values.
The <code>-parameter is a two-letter abbreviation of the language. The language codes, as defined in ISO 639, consists
of two characters, e.g. "sv", "en" etc.
The complete set of language codes to be used are manufacturer specific and should all be possible to use with the
command. Some examples are described under <code>. For a complete list see ISO 639.
The read command gives the current language as output. If the language has been set to "AUTO", the read command
returns the current language set from the currently selected SIM-card /UICC. Hence, the "AUTO"-code is never
returned by the read-command.
Test command returns supported <code>s as a compound value.
Defined values
<code>: (not all language codes are present in this list)
"AUTO" Read language from SIM-card /UICC. "Auto" is not returned by the read-command.
"sw" Swedish
"fi" Finnish
"da" Danish
"no" Norwegian
"de" German
"fr" French
"es" Spanish
"it" Italian
"en" English
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
131
3GPP
TS 27.007 version 13.3.0 Release 13
Implementation
Optional.
8.31 Language event +CLAE
Table 91: +CLAE parameter command syntax
Command
Possible response(s)
+CLAE=[<mode>] +CME ERROR: <err>
+CLAE? +CLAE: <mode>
+CME ERROR: <err>
+CLAE=?
+CLAE: (list of supported <mode>s)
+CME ERROR: <err>
Description
This command is used to enable/disable unsolicited result code +CLAV: <code>. If <mode>=1, +CLAV: <code>
is sent from the MT when the language in the MT is changed. If setting fails, a MT error, +CME ERROR: <err> is
returned. Refer subclause 9.2 for possible <err> values.
Read command returns the current status for <mode>.
Test command returns supported <mode>s as a compound value.
Defined values
<mode>: integer type
0 Disable unsolicited result code +CLAE
1 Enable unsolicited result code +CLAE
<code>: For description see +CLAN.
Implementation
Optional.
8.32 Set greeting text +CSGT
Table 92: +CSGT parameter command syntax
Command
Possible response(s)
+CSGT=<mode>[,<text>] +CME ERROR: <err>
+CSGT? +CSGT: <text>,<mode>
+CME ERROR: <err>
+CSGT=?
+CSGT: (list of supported <mode>s),<ltext>
+CME ERROR: <err>
Description
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
132
3GPP TS 27.007 version 13.3.0 Release 13
This command sets and activates the greeting text in the MT. The greeting text is shown in the MT display when the
MT is turned on. The command can also be used to deactivate a text. If setting fails in an MT error,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
The read command queries the current <text> and the status of the <mode> parameter
Test command returns supported <mode>s as a compound value and the maximum number of characters in <text>.
Example: +CSGT: (0-1),20
Defined values
<mode>: integer type
0 Turn off greeting text
1 Turn on greeting text
<text>: string type. A manufacturer specific free text that can be displayed. The text can not include <CR>
<mode>: integer type. Maximum number of characters in <text>.
Implementation
Optional.
8.33 Set voice mail number +CSVM
Table 93: +CSVM parameter command syntax
Command
Possible response(s)
+CSVM=<mode>[,<number>[,<
type>]] +CME ERROR: <err>
+CSVM? +CSVM: <mode>,<number>,<type>
+CME ERROR: <err>
+CSVM=?
+CSVM: (list of supported <mode>s),(list of
supported <type>s)
+CME ERROR: <err>
Description
The number to the voice mail server is set with this command. The parameters <number> and <type> can be left out
if the parameter <mode> is set to 0. If setting fails, an MT error, +CME ERROR: <err> is returned. Refer
subclause 9.2 for possible <err> values.
Read command returns the currently selected voice mail number and the status (i.e. enabled/disabled).
Test command returns supported <mode>s and <type>s as compound values.
Defined values
<mode>: integer type
0 Disable the voice mail number.
1 Enable the voice mail number.
<number>: string type; Character string <0..9,+>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
133
3GPP TS 27.007 version 13.3.0 Release 13
<type>: integer type; Type of address octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7);
default 145 when dialling string includes international access code character "+", otherwise 129.
129 ISDN / telephony numbering plan, national / international unknown
145 ISDN / telephony numbering plan, international number
161 ISDN / telephony numbering plan, national number
128 - 255 Other values refer 3GPP TS 24.008 [8] subclause 10.5.4.7
Implementation
Optional.
8.34 Ring melody control +CRMC
Table 94: +CRMC parameter command syntax
Command
Possible response(s)
+CRMC=<index>,<volume>[,[
<call type>][,<profile>]] +CME ERROR: <err>
+CRMC? +CRMC: <index>,<volume>[,[<call
type1>][,<profile1>]]
[<CR><LF>+CRMC: <index>,<volume>[,[<c
all type2>][,<profile1>]][...]]
[<CR><LF>+CRMC: <index>,<volume>[,[<c
all type1>][,<profile2>]]]
[<CR><LF>+CRMC: <index>,<volume>[,[<c
all type2>][,<profile2>]][...]]
+CME ERROR: <err>
+CRMC=? +CRMC: (list of supported <index>s),(list of
supported <volume>s)[,[(list of supported <call
type>s)][,(list of supported <profile>s)]]
+CME ERROR: <err>
Description
Write command causes the MT to set a specific ring melody and volume for the selected call type and profile. The
default values for the optional parameters are defined by the manufacturer.
Read command queries the settings for the ring melody. If call types and profiles are available the corresponding ring
melodies are listed. Starting with call type1 and profile1 the ring melody settings for each available profile and call type
is issued.
Test command returns the list of supported indexes, volumes, call types and profiles as compound values.
Refer subclause 9.2 for possible <err> values.
Defined values
<index>: integer type; manufacturer specific number to identify a certain ring melody
<volume>: integer type value with manufacturer specific range (smallest value represents the lowest sound level)
<call typex>: integer type; manufacturer specific number for a call type
<profilex>: integer type; manufacturer specific number for a profile
Implementation
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
134
3GPP TS 27.007 version 13.3.0 Release 13
Optional.
8.35 Ring melody playback +CRMP
Table 95: +CRMP action command syntax
Command
Possible response(s)
+CRMP=<call
type>[,<volume>[,<type>,<
index>]]
+CME ERROR: <err>
+CRMP=? +CRMP: (list of supported <call
type>s),(list of supported
<volume>s),(<type0>),(list of supported
<index>s)
[<CR><LF>+CRMP: (list of supported <call
type>s),(list of supported
<volume>s),(<type1>),(list of supported
<index>s)]
+CME ERROR: <err>
Description
Execution command causes the MT to playback a specific ring type. The default values for the optional parameters are
the current selected in the MT.
Test command returns the supported call types, volumes, types and indexes as compound values. The manufacturer
defined and the user defined values are returned on separate lines.
Refer subclause 9.2 for possible <err> values.
Defined values
<call type>: integer type; manufacturer specific
<volume>: integer type value with manufacturer specific range (smallest value represents the lowest sound level)
<type>: integer type
0 Manufacturer defined
1 User defined
<index>: integer type
Implementation
Optional.
8.36 Master reset +CMAR
Table 96: +CMAR action command syntax
Command
Possible response(s)
+CMAR=<phone lock code> +CME ERROR: <err>
+CMAR=?
+CME ERROR: <err>
Description
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
135
3GPP TS 27.007 version 13.3.0 Release 13
This command requests the MT to reset user data. The user data in the phone will be reset to default values. If setting
fails, a MT error, +CME ERROR: <err>, is returned. Refer subclause 9.2 for possible <err> values.
If the MT is locked and this command is used, then the MT will be unlocked after the master reset.
Test command returns OK.
Defined values
<phone lock code> string type; Security code (Phone Lock code) must be verified before performing the
master reset.
Implementation
Optional.
8.37 List all available AT commands +CLAC
Table 97: +CLAC action command syntax
Command
Possible response(s)
+CLAC <AT Command1>
[<CR><LF><AT Command2>
[...]]
+CME ERROR: <err>
+CLAC=?
+CME ERROR: <err>
Description
Execution command causes the MT to return one or more lines of AT Commands. Refer subclause 9.2 for possible
<err> values.
NOTE: This command only returns the AT commands that are available for the user.
Defined values
<AT Command>: Defines the AT command including the prefix AT. Text shall not contain the sequence 0<CR> or
OK<CR>
Implementation
Optional.
8.38 Delete alarm +CALD
Table 98: +CALD action command syntax
Command
Possible response(s)
+CALD=<n> +CME ERROR: <err>
+CALD=?
+CALD: (list of supported <n>s)
+CME ERROR: <err>
Description
Action command deletes an alarm in the MT. If the command fails in an MT error, +CME ERROR: <err> is
returned. Refer subclause 9.2 for possible <err> values.
Test command returns supported array index values as a compound value.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
136
3GPP TS 27.00
7 version 13.3.0 Release 13
Defined values
<n>: integer type value indicating the index of the alarm; default is manufacturer specific
Implementation
Optional.
8.39 Postpone or dismiss an alarm +CAPD
Table 99: +CAPD action command syntax
Command
Possible response(s)
+CAPD[=<sec>] +CME ERROR: <err>
+CAPD=?
+CAPD: (list of supported <sec>s)
+CME ERROR: <err>
NOTE:
The syntax of the AT Set Command is corrected to be according to
ITU-T Recommendation V.250 [14]. Older versions of the
specification specify incorrect syntax +CAPD=[<sec>].
Description
Set command postpones or dismisses a currently active alarm. If the command fails in an MT error,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Test command returns supported <sec>-parameter values as a compound value.
Defined values
<sec>: integer type value indicating the number of seconds to postpone the alarm. If <sec> is set to 0 (default),
the alarm is dismissed.
Implementation
Optional.
8.40 Automatic time zone update +CTZU
Table 100: +CTZU parameter command syntax
Command
Possible response(s)
+CTZU=[<onoff>] +CME ERROR: <err>
+CTZU? +CTZU: <onoff>
+CME ERROR: <err>
+CTZU=?
+CTZU: (list of supported <onoff>s)
+CME ERROR: <err>
Description
Set command enables and disables automatic time zone update via NITZ. If setting fails in an MT error,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
Read command returns the current settings in the MT.
Test command returns supported on- and off-values as a compound value.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
137
3GPP TS 27.007 version 13.3.0 Release 13
Defined values
<onoff>: integer type value indicating
0 Disable automatic time zone update via NITZ.
1 Enable automatic time zone update via NITZ.
Implementation
Optional.
8.41 Time zone reporting +CTZR
Table 101: +CTZR parameter command syntax
Command
Possible response(s)
+CTZR=[<reporting>] +CME ERROR: <err>
+CTZR? +CTZR:<reporting>
+CME ERROR: <err>
+CTZR=?
+CTZR: (list of supported
<reporting>s)
+CME ERROR: <err>
Description
This set command controls the time zone change event reporting. If reporting is enabled the MT returns the unsolicited
result code +CTZV: <tz>, +CTZE: <tz>,<dst>,[<time>], or +CTZEU: <tz>,<dst>,[<utime>]
whenever the time zone is changed. The MT also provides the time zone upon network registration if provided by the
network. If setting fails in an MT error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err>
values.
Read command returns the current reporting settings in the MT.
Test command returns supported <reporting>-values as a compound value.
NOTE: The Time Zone reporting is not affected by the Automatic Time Zone setting command, +CTZU.
Defined values
<reporting>: integer type value indicating:
0 disable time zone change event reporting.
1 Enable time zone change event reporting by unsolicited result code +CTZV: <tz>.
2 Enable extended time zone and local time reporting by unsolicited result code
+CTZE: <tz>,<dst>,[<time>].
3 Enable extended time zone and universal time reporting by unsolicited result code
+CTZEU: <tz>,<dst>,[<utime>].
<tz>: string type value representing the sum of the local time zone (difference between the local time and GMT
expressed in quarters of an hour) plus daylight saving time. The format is "±zz", expressed as a fixed width, two
digit integer with the range -48 ... +56. To maintain a fixed width, numbers in the range -9 ... +9 are expressed
with a leading zero, e.g. "-09", "+00" and "+09".
<dst>: integer type value indicating whether <tz> includes daylight savings adjustment;
0 <tz> includes no adjustment for Daylight Saving Time
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
138
3GPP TS 27.007 version 13.3.0 Release 13
1 <tz> includes +1 hour (equals 4 quarters in <tz>) adjustment for daylight saving time
2 <tz> includes +2 hours (equals 8 quarters in <tz>) adjustment for daylight saving time
<time>: string type value representing the local time. The format is "YYYY/MM/DD,hh:mm:ss", expressed as
integers representing year (YYYY), month (MM), date (DD), hour (hh), minute (mm) and second (ss). The local
time can be derived by the MT from information provided by the network at the time of delivering time zone
information and will be present in the unsolicited result code for extended time zone and local time reporting if
the universal time is provided by the network.
<utime>: string type value representing the universal time. The format is "YYYY/MM/DD,hh:mm:ss", expressed
as integers representing year (YYYY), month (MM), date (DD), hour (hh), minute (mm) and second (ss). The
universal time can be provided by the network at the time of delivering time zone information and will be
present in the unsolicited result code for extended time zone and universal time reporting if provided by the
network.
Implementation
Optional.
8.42 Enter protocol mode+CPROT
Table 102: +CPROT action command syntax
Command
Possible response(s)
+CPROT=<proto>[,<version>[
,<lsap1>[,
...
[<lsapN>]]]] CONNECT
NO CARRIER
OK
ERROR
+CME ERROR: <err>
+CPROT=? +CPROT: <proto1>[,(list of supported
<version>s)[,(list of supported <lsap1>s)[,...[,(list
of supported <lsapN>s)]]]]
[<CR><LF>+CPROT: <proto2>[,(list of supported
<version>s)[,(list of supported
<lsap1>s)[,...[,(list of supported <lsapN>s)]]]]
[...]]
Description
Set command informs TA that TE wants to establish a peer-to-peer protocol <proto> or upper layer connection
(indicating by the <lsap>s setting) with the MT on the link from which the command was received. This command
can be used in case the link between TE and MT does not provide itself such a mechanism.
If MT has succeeded in establishing a logical link between application protocols and external interface, it will send
CONNECT message to the TE. Otherwise, the NO CARRIER response will be returned.
If the CONNECT response is received, TE can start sending <proto> or upper layer frames.
The connection shall always return for <proto> mode when the protocol session is ended. When the MT receives a
disconnect request from its peer entity, it will process it and send OK response to the TE indicating its capability for
receiving new AT commands. Since <proto> or upper layers can be accessed in other ways, TA must have pre-
knowledge of the fact that connection is initiated with AT+CPROT command. This means that switch to <proto>
mode must include some sort of notification to the protocol entity.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
139
3GPP TS 27.007 version 13.3.0 Release 13
This command can be aborted by sending a <proto> or upper layer disconnection frame. In that case, MT will return
in command mode by sending the OK response.
Refer subclause 9.2 for possible <err> values.
Test command returns values supported as compound values.
Defined values
<proto>: integer type
0 OBEX (refer IrDA Object Exchange Protocol [44]).
…15 reserved by the present document
16... manufacturer specific
<version>: version number of <proto>: string type
<lsap1>: integer type; defines a level of service or application protocol on the top of <proto> layer. It may refer
to services or protocols defined in other standards development organizations (SDOs).
1 IrMC level 1 (Minimum Level) Only .(refer [43] subclause 2.9.4)
2 IrMC level 1 and 2 (Minimum and Access Levels) Only. .(refer [43] subclause 2.9.4)
4 IrMC level 1, 2 and 3 (Minimum, Access, Index Levels) Only- implies static index support.
.(refer [43] subclause 2.9.4)
8 IrMC level 1, 2 and 4 (Minimum, Access and Sync Levels) Only-implies unique index support.
.(refer [43] subclause 2.9.4)
10 IrMC level 1, 2, 3 and 4 (Minimum, Access, Index and Sync Levels)-implies support of static and
unique index. .(refer [43] subclause 2.9.4)
…15 reserved by the present document
16... manufacturer specific
<lsap2>...<lsapN>: integer type
In case <lsapN>,<lsapN+1> received in the +CPROT command identifies protocol layers, the protocol
identified by N+1 shall be on the top of the protocol identified by N on a framework point of view.
0…15 reserved by the present document
16... manufacturer specific
Implementation
Optional.
8.43 Generic UICC logical channel access +CGLA
Table 103: +CGLA action command syntax
Command
Possible response(s)
+CGLA=<sessionid>,<length>
,<command> +CGLA: <length>,<response>
+CME ERROR: <err>
+CGLA=?
Description
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
140
3GPP TS 27.007 version 13.3.0 Release 13
Set command transmits to the MT the <command> it then shall send as it is to the selected UICC. In the same manner
the UICC <response> shall be sent back by the MT to the TA as it is. Refer subclause 9.2 for possible <err>
values.
This command allows a direct control of the currently selected UICC by a distant application on the TE. The TE shall
then take care of processing UICC information within the frame specified by GSM/UMTS.
Although Generic UICC Logical Channel Access command +CGLA allows TE to take control over the UICC-MT
interface, there are some functions of the UICC-MT interface that logically do not need to be accessed from outside the
TA/MT. Moreover, for security reason the GSM network authentication should not be handled outside the TA/MT.
Therefore it shall not be allowed to execute a Run GSM Algorithm command or an Authenticate command in GSM
context from the TE using +CGLA at all time whether the +CGLA is locked or unlocked. This shall not forbid the TE to
send Authenticate commands in other security contexts (e.g. EAP security context).
For example, the TA/MT shall forbid the transfer of the Authenticate command to a USIM application when parameters
P2 = 0 (GSM security context). See 3GPP TS 31.102 [59] for USIM authenticate command definition.
NOTE: Compared to Restricted UICC Access command +CRLA, the definition of +CGLA allows TE to take more
control over the UICC-MT interface. The locking and unlocking of the interface may be done by a special
<command> value or automatically by TA/MT (by interpreting <command> parameter). In case that TE
application does not use the unlock command (or does not send a <command> causing automatic
unlock) in a certain timeout value, MT may release the locking.
Defined values
<sessionid>: integer type; this is the identifier of the session to be used in order to send the APDU commands
to the UICC. It is manadatory in order to send commands to the UICC when targeting applications on the smart
card using a logical channel other than the default channel (channel "0").
<length> : integer type; length of the characters that are sent to TE in <command> or <response> (two times
the actual length of the command or response)
<command> : command passed on by the MT to the UICC in the format as described in 3GPP TS 31.101 [65]
(hexadecimal character format; refer +CSCS)
<response> : response to the command passed on by the UICC to the MT in the format as described in
3GPP TS 31.101 [65] (hexadecimal character format; refer +CSCS)
Implementation
Optional.
8.44 Restricted UICC logical channel access +CRLA
Table 104: +CRLA action command syntax
Command
Possible response(s)
+CRLA=<sessionid>,<command>[,<fi
leid>[,<P1>,<P2>,<P3>[,<data>[,<
pathid>]]]]
+CRLA: <sw1>,<sw2>[,<response>]
+CME ERROR: <err>
+CRLA=?
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
141
3GPP TS 27.007 versio
n 13.3.0 Release 13
Description
By using this command instead of Generic UICC Access +CGLA TE application has easier but more limited access to
the UICC database. Set command transmits to the MT the UICC <command> and its required parameters. MT handles
internally, for the selected UICC, all UICC-MT interface locking and file selection routines. As response to the
command, MT sends the actual UICC information parameters and response data. MT error result code +CME ERROR
may be returned when the command cannot be passed to the UICC, but failure in the execution of the command in the
UICC is reported in <sw1> and <sw2> parameters. Refer subclause 9.2 for possible <err> values.
Coordination of command requests to UICC and the ones issued by GSM/UMTS application inside the MT is
implementation dependent. However the TE should be aware of the precedence of the GSM/UMTS application
commands to the TE commands.
Defined values
<sessionid>: integer type; this is the identifier of the session to be used in order to send the APDU commands
to the UICC. It is mandatory in order to send commands to the UICC when targeting applications on the smart
card using a logical channel other than the default channel (channel "0").
<command> (command passed on by the MT to the UICC; refer 3GPP TS 31.101 [65]):
176 READ BINARY
178 READ RECORD
192 GET RESPONSE
214 UPDATE BINARY
220 UPDATE RECORD
242 STATUS
203 RETRIEVE DATA
219 SET DATA
all other values are reserved
NOTE 1: The MT internally executes all commands necessary for selecting the desired file, before performing the
actual command.<fileid>: integer type; this is the identifier of a elementary datafile on UICC.
Mandatory for every command except STATUS.
NOTE 2: The range of valid file identifiers depends on the actual UICC and is defined in 3GPP TS 31.101 [65].
Optional files may not be present at all.<P1>, <P2>, <P3>: integer type; parameters passed on by the
MT to the UICC. These parameters are mandatory for every command, except GET RESPONSE and
STATUS. The values are described in 3GPP TS 31.101 [65].
<data>: information which shall be written to the SIM (hexadecimal character format; refer +CSCS)
<pathid>: string type; contains the path of an elementary file on the UICC in hexadecimal format (e.g.
"5F704F30" for DF
SoLSA
/EF
SAI
). The <pathid> shall only be used in the mode "select by path from current
DF" as defined in ETSI TS 102 221 [60].
<sw1>, <sw2>: integer type; information from the UICC about the execution of the actual command. These
parameters are delivered to the TE in both cases, on successful or failed execution of the command
<response>: response of a successful completion of the command previously issued (hexadecimal character
format; refer +CSCS). STATUS and GET RESPONSE return data, which gives information about the current
elementary datafield. This information includes the type of file and its size (refer 3GPP TS 31.101 [65]). After
READ BINARY, READ RECORD or RETRIEVE DATA command the requested data will be returned.
<response> is not returned after a successful UPDATE BINARY, UPDATE RECORD or SET DATA
command
Implementation
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
142
3GPP TS 27.007 version 13.3.0 Release 13
Optional.
8.45 Open logical channel +CCHO
Table 105: +CCHO action command syntax
Command
Possible response(s)
+CCHO=<dfname>
<sessionid>
+CME ERROR: <err>
+CCHO=?
Description
Execution of the command causes the MT to return <sessionid> to allow the TE to identify a channel that is being
allocated by the currently selected UICC, which is attached to ME. The currently selected UICC will open a new logical
channel; select the application identified by the <dfname> received with this command and return a session Id as the
response. The ME shall restrict the communication between the TE and the UICC to this logical channel.
This <sessionid> is to be used when sending commands with Restricted UICC Logical Channel access +CRLA or
Generic UICC Logical Channel access +CGLA commands.
NOTE: The logical channel number is contained in the CLASS byte of an APDU command, thus implicitly
contained in all APDU commands sent to a UICC. In this case it will be up to the MT to manage the
logical channel part of the APDU CLASS byte and to ensure that the chosen logical channel is relevant to
the <sessionid> indicated in the AT command. See 3GPP TS 31.101 [65] for further information on
logical channels in APDU commands protocol.
Refer subclause 9.2 for possible <err> values.
Defined values
<dfname>: all selectable applications in the UICC are referenced by a DF name coded on 1 to 16 bytes
<sessionid>: integer type; a session Id to be used in order to target a specific application on the smart card (e.g.
(U)SIM, WIM, ISIM) using logical channels mechanism
See 3GPP TS 31.101 [65] for more information about defined values.
Implementation
Optional.
8.46 Close logical channel +CCHC
Table 106: +CCHC action command syntax
Command
Possible response(s)
+CCHC=<sessionid> +CCHC
+CME ERROR: <err>
+CCHC=?
Description
This command asks the ME to close a communication session with the active UICC. The ME shall close the previously
opened logical channel. The TE will no longer be able to send commands on this logical channel. The UICC will close
the logical channel when receiving this command. Refer subclause 9.2 for possible <err> values.
ETSI
ETSI TS 1
27 007 V13.3.0 (2016
-
03)
143
3GPP TS 27.007 version 13.3.0 Release 13
Defined values
<sessionid>: integer type; a session Id to be used in order to target a specific application on the smart card (e.g.
(U)SIM, WIM, ISIM) using logical channels mechanism
Implementation
Optional.
8.47 EAP authentication +CEAP
Table 107: +CEAP action command syntax
Command
Possible response(s)
+CEAP=<dfname>,<EAPMet
hod>,<EAP packet data>
[,<DFeap>]
+CEAP: <EAPsessionid>,
<EAP packet response>
+CME ERROR: <err>
+CEAP=?
Description
This command allows a TE to exchange EAP packets with the UICC or the ME.
Prior to the execution of this command, the TE shall retrieve the available AIDs using the +CUAD command. The TE
shall select one appropriate AID to be addressed. Selection may include asking the user, and considering EAP methods
supported by the AIDs. The TE shall set the <dfname> value using the selected AID and shall set the
<EAPMethod> value to the requested EAP method. The TE may set the <DFeap> value to the directory file
identifier that is applicable to the <EAPMethod>; which is derived from the discretionary data returned by +CUAD.
The parameter is mandatory for EAP terminated in UICC.
If the targeted application on the UICC does support the requested EAP method, the MT shall use the value provided in
<DFeap>, and it shall transmit the <EAP packet data> to the UICC application using the Authenticate APDU
command as defined in ETSI TS 102 310 [66]. The appropriate DF
EAP
in the ADF must be selected prior to the
submission of an EAP Authenticate command with the <EAP packet data>. Then the EAP Response data sent by
the UICC application in its response to the Authenticate command shall be provided to the TE in <EAP packet
response>.
If the targeted application on the UICC does not support the requested EAP method and if the MT does support this
method then the <EAP packet data> shall be handled by the MT. During the handling of the EAP method, the MT
shall run the authentication algorithm on the SIM or USIM, respectively.
Also the MT has to allocate an <EAPsessionid> in order to identify an EAP session and its corresponding keys and
parameters.
If neither the MT nor the appropriate UICC application support the requested EAP method, the MT shall respond with
CME ERROR: 49 (EAP method not supported).
Refer subclause 9.2 for possible <err> values.
Defined values
<dfname>: string type in hexadecimal character format. All selectable applications are represented in the UICC by
an AID coded on 1 to 16 bytes.
<EAPMethod>: string type in hexadecimal character format. This is the EAP Method Type as defined in
RFC 3748 [68] in 1 byte format or 8 bytes expanded format. The v alue range for 1 byte format and for 8 bytes
expanded format is defined in RFC 3748 [68].
<EAP packet data>: string type in hexadecimal character format. This is the EAP packet data in hexadecimal
character as defined in ETSI TS 102 310 [66].
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
144
3GPP TS 27.007 version 13.3.0 Release 13
<DFeap>: string type in hexadecimal character format. Contains the DF(EAP) associated with the specified
<EAPMethod> on the SIM/UICC as defined in ETSI TS 102 310 [66] (e.g. "6D34").
<EAPsessionid>: integer type. This is the identifier of the EAP session to be used in order to retrieve the EAP
parameters with EAP Retreive Parameters +CERP command. Value range is from 1 to 4294967295.
<EAP packet response>: string type in hexadecimal character format. Defined in ETSI TS 102 310 [66].
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
145
3GPP TS 27.007 version 13.3.0 Release 13
8.48 EAP retrieve parameters +CERP
Table 108: +CERP action command syntax
Command
Possible response(s)
+CERP=<EAPsessionid>,
<EAPparameter> +CERP: <EAP parameter
response>
+CME ERROR: <err>
+CERP=?
Description
This command allows a TE to retrieve EAP session parameters / derived keys after a run of the +CEAP command. If the
EAP session is handled by the UICC then the MT shall return the content of the elementary file corresponding to the
indicated <EAPparameter>. Those EFs are defined in ETSI TS 102 310 [66].
If the MT handles the EAP session then the MT shall return the corresponding parameter encoded as defined for EAP
files, see ETSI TS 102 310 [66].
For example, the keys shall be retrieved in the TLV format described in ETSI TS 102 310 [66].
If neither the MT nor the appropriate UICC application can provide the requested information (e.g. because the
requested EAP session ID does not exist), the MT shall respond with CME ERROR: 50 (Incorrect parameters).
Refer subclause 9.2 for possible <err> values.
Defined values
<EAPparameter>: integer type.
1 Keys
2 Status
3 Identity
4 Pseudonym
<EAPsessionid>: integer type; this is the identifier of the EAP session to be used in order to retrieve the EAP
parameters corresponding to an active EAP session. Value range is from 1 to 4294967295.
<EAP parameter response>: string type in hexadecimal character format. The format of the parameter is
defined in ETSI TS 102 310 [66]. The <EAP parameter response> depends on the value of the
<EAPparameter>.
Implementation
Optional.
8.49 UICC application discovery +CUAD
Table 109: +CUAD action command syntax
Command
Possible
response(s)
+CUAD[=<option>] +CUAD: <response>[,<active_application>[,<AID>]]
+CME ERROR: <err>
+CUAD=? +CUAD: (list of supported <option>s)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
146
3GPP TS 27.007 version 13.3.0
Release 13
Description
This command asks the MT to discover what applications are available for selection on the UICC. According to
ETSI TS 102 221 [60], the ME shall access and read the EF
DIR
file in the UICC and return the values that are stored in
its records. Each record contains the AID and optionally application parameters of one of the applications available on
the UICC.
If optional parameter(s) are requested and the EF
DIR
file is not present in the UICC, <response> shall be empty.
Refer subclause 9.2 for possible <err> values.
Test command returns the supported option values as a compound value.
Defined values
<response>: string type in hexadecimal character format. The response is the content of the EF
DIR
.
<option>: integer type.
0: no parameters requested in addition to <response>.
1 include <active_application>.
<active_application>: integer type.
0 no SIM or USIM active.
1 active application is SIM.
2 active application is USIM, followed by <AID>.
<AID>: string type in hexadecimal character format. AID of active USIM.
Implementation
Optional.
8.50 Mobile originated location request +CMOLR
Table 8.50-1: +CMOLR parameter command syntax
Command
Possible response(s)
+CMOLR=[<enable>[,<method>[,<hor-acc-
set>[,<hor-acc>[,<ver-req>[,<ver-acc-
set>[,<ver-acc>[,<vel-req>[,<rep-
mode>[,<timeout>[,<interval>[,<shape-
rep>[,<plane>[,<NMEA-rep>[,<third-
party-address>]]]]]]]]]]]]]]]]
+CME ERROR: <err>
+CMOLR? +CMOLR: <enable>,<method>,<hor-acc-
set>,[<hor-acc>],<ver-req>,[<ver-acc-
set>],[<ver-acc>],<vel-req>,<rep-
mode>,<timeout>,[<interval>],<shape-
rep>,[<plane>],[<NMEA-rep>],[<third-
party-address>]
+CME ERROR: <err>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
147
3GPP TS 27.007 version 13.3.0 Release 13
+CMOLR=? +CMOLR: (list of supported <enable>s),(list of
supported <method>s),(list of supported <hor-
acc-set>s),(list of supported <hor-acc>s),(list
of supported <ver-req>s),(list of supported <ver-
acc-set>s),(list of supported <ver-acc>s),(list
of supported <vel-req>s),(list of supported <rep-
mode>s),(list of supported <timeout>s),(list of
supported <interval>s),(list of supported
<shape-rep>s),(list of supported
<plane>s),(list of supported <NMEA-rep>s),(list
of supported <third-party-address>s)
Description
Set command initiates a mobile originated location request (MO-LR). The parameter <enable> enables or disables
positioning and reporting by unsolicited result codes. Reporting can be performed in the format of GAD shapes
<location_parameters> or in the format of NMEA strings <NMEA-string> or both. The unsolicited result
codes that can be provided are +CMOLRG: <location_parameters> and/or +CMOLRN: <NMEA-string>.
The method to use for positioning is decided by the parameter <method>. The parameters <hor-acc-set>, <hor-
acc>, <ver-req>, <ver-acc-set>, <ver-acc> and <vel-req> indicate accuracy for the MO-LR. The
parameter <timeout> indicates how long the MS will wait for a report before an unsolicited result code is provided.
A single report or periodic reports can be requested by the parameter <rep-mode>. If periodic reports are requested,
the time interval between the reports is specified by the parameter <interval>. If GAD shapes are requested, the
GAD shapes that will be accepted in the unsolicited result code <location_parameters> are defined by the
parameter <shape-rep>. The parameter <plane> specifies the signalling to use for MO-LR. The parameter
<NMEA-rep> indicates possible restrictions in supported NMEA strings. The parameter <third-party-
address> is used to specify the address when reporting to a third party is specified. Additional information about
positioning can be found in 3GPP TS 25.305 [77]. If positioning-data cannot be provided at a timeout, the unsolicited
result +CMOLRE is provided. Refer subclause 9.2 and subclause 9.3 for possible <err> values.
Read command returns the current settings of the parameters <enable>, <method>, <hor-acc-set>, <hor-
acc>, <ver-req>, <ver-acc-set>, <ver-acc>, <vel-req>, <rep-mode>, <timeout>, <interval>
<shape-rep>, <plane>, <NMEA-rep> and <third-party-address>. The parameters <hor-acc>, <ver-
acc-set>, <ver-acc> and <plane> are only applicable in certain configurations. The parameter <interval>
is only applicable if periodic reporting is specified. The parameter <NMEA-rep> is only applicable if reporting is
specified by NMEA strings.The parameter <third-party-address> is only applicable if reporting to third party
is specified.
Test command returns the supported values and ranges.
Defined values
<enable>: integer type. Enables and disables reporting location as a result of a MO-LR. Only one <method> can
be enabled at any given time.
0 Disables reporting and positioning.
1 Enables reporting of NMEA strings by unsolicited result code +CMOLRN: <NMEA-string>.
Lack of data at each timeout is indicated by an unsolicited result code +CMOLRE.
2 Enables reporting of GAD shapes by unsolicited result code +CMOLRG: <location_parameters>.
Lack of data at each timeout is indicated by an unsolicited result code +CMOLRE.
3 Enables reporting of NMEA strings and GAD shapes by unsolicited result codes
+CMOLRG: <location_parameters> and +CMOLRN: <NMEA-string>.
Lack of data at each timeout is indicated by an unsolicited result code +CMOLRE.
ETSI
ETSI TS 127 007 V
13.3.0 (2016
-
03)
148
3GPP TS 27.007 version 13.3.0 Release 13
NOTE 1: The string of <location_parameters> intended for +CMOLR can be split into multiple unsolicited
result codes e.g. in order to prevent that the string in the unsolicited result code becomes too long. How to
split the string is implementation specific.
<method>: integer type. Method for MO-LR. The default value is implementation specific.
0 Unassisted GPS. Autonomous GPS only, no use of assistance data.
1 Assisted GPS (see NOTE 2).
2 Assisted GANSS (see NOTE 2).
3 Assisted GPS and GANSS (see NOTE 2).
4 Basic self location (the network determines the position technology).
5 Transfer to third party. This method makes the parameters <shape-rep> and <NMEA-rep> irrelevant
(any values are accepted and disregarded). The third party address is given in the parameter <third-
party-address> (see NOTE 3).
6 Retrieval from third party. This method is to get the position estimate of the third party. The third party
address is given in the parameter <third-party-address>.
NOTE 2: For the methods that require assistance data, the assistance data obtained from the network is used for a
UE-based GPS location procedure.
NOTE 3: Lack of data at each timeout is not indicated by an unsolicited result code +CMOLRE if reporting to third
party is specified.
<hor-acc-set>: integer type.
0 Horisontal accuracy not set/specified.
1 Horizontal accuracy set in parameter <hor-acc>.
<hor-acc>: integer type. Requested accuracy as horizontal uncertainty exponent (refer to 3GPP TS 23.032 [76]
subclause 6.2). The value range is 0-127. The default value is implementation specific.
<ver-req>: integer type.
0 Vertical coordinate (altitude) is not requested, 2D location fix is acceptable. The parameters <ver-acc-
set> and <ver-acc> do not apply.
1 Vertical coordinate (altitude) is requested, 3D location fix is required.
<ver-acc-set>: integer type.
0 Vertical accuracy not set/specified.
1 Vertical accuracy set/specified in parameter <ver-acc>.
<ver-acc>: integer type. Requested accuracy as vertical uncertainty exponent (refer to 3GPP TS 23.032 [76]
subclause 6.4). The value range is 0-127. The default value is implementation specific.
<vel-req>: integer type. Requested velocity type (refer to 3GPP TS 23.032 [76] subclause 8.6).
0 Velocity not requested.
1 Horizontal velocity requested.
2 Horizontal velocity and vertical velocity requested.
3 Horizontal velocity with uncertainty requested.
4 Horizontal velocity with uncertainty and vertical velocity with uncertainty requested.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
149
3GPP TS 27.007 version 13.3.0 Release 13
<rep-mode>: integer type. Reporting mode. The default value is implementation specific.
0 Single report, the timeout for the MO-LR response request is specified by <timeout>.
1 Periodic reporting, the timeout for each MO-LR response request is specified by <timeout> and the
interval between each MO-LR is specified by <interval>.
<timeout>: integer type. Indicates how long the MS will wait for a response after a MO-LR. The value range is in
seconds from 1 to 65535. The default value is implementation specific.
<interval>: integer type. The parameter is applicable to periodic reporting only. Determine the interval between
periodic MO-LRs. The value range is in seconds from 1 to 65535, and must be greater than or equal to
<timeout>. The default value is implementation specific.
<shape-rep>: integer type. This parameter is a sum of integers each representing a certain GAD shape that will
be accepted in the unsolicited result code <location_parameters>. Note that only one GAD shape is
present per unsolicited result code. The default value is implementation specific.
1 Ellipsoid point.
2 Ellipsoid point with uncertainty circle.
4 Ellipsoid point with uncertainty ellipse.
8 Polygon.
16 Ellipsoid point with altitude.
32 Ellipsoid point with altitude and uncertainty ellipsoid.
64 Ellipsoid arc.
<plane>: integer type. The parameter specifies whether the control plane or SUPL will be used for MO-LR.
0 Control plane.
1 Secure user plane (SUPL).
<NMEA-rep>: string type. The supported NMEA strings are specified as a comma separated values inside one
string. If the parameter is omitted or an empty string is given, no restrictions apply and all NMEA strings are
supported. The default value is that all strings are supported.
Example of NMEA strings: "$GPRMC,$GPGSA,$GPGSV"
<third-party-address>: string type. The parameter is applicable to reporting to third party only, and
specifies the address to the third party. This parameter has to be specified when <method> value is set to 5
or 6.
<location_parameters>: string type in UTF-8. This parameter provides XML-formatted strings of GAD-
shape positioning data as defined in table 8.50-2. This parameter shall not be subject to conventional character
conversion as per +CSCS. The XML according to the DTD in table 8.50-2 may be provided in one or multiple
unsolicited result codes.
Table 8.50-2: XML DTD for <location_parameters>
<?xml version="1.0" ?>
<!DOCTYPE location_parameters [
<!ELEMENT location_parameters (time?,direction?,shape_data,velocity_data?)>
<!ELEMENT time (#PCDATA)>
<!ELEMENT direction (#PCDATA)>
<!ELEMENT shape_data
(ellipsoid_point|ellipsoid_point_uncert_circle|ellipsoid_point_uncert_ellipse|po
lygon|ellipsoid_point_alt|ellipsoid_point_alt_uncertellipse|ellips_arc)>
<!ELEMENT ellipsoid_point (coordinate)>
<!ELEMENT coordinate (latitude,longitude)>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
150
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT latitude (north,degrees)>
<!ELEMENT north (#PCDATA)>
<!ELEMENT degrees (#PCDATA)>
<!ELEMENT longitude (#PCDATA)>
<!ELEMENT ellipsoid_point_uncert_circle (coordinate,uncert_circle)>
<!ELEMENT uncert_circle (#PCDATA)>
<!ELEMENT ellipsoid_point_uncert_ellipse (coordinate,uncert_ellipse)>
<!ELEMENT uncert_ellipse
(uncert_semi_major,uncert_semi_minor,orient_major,confidence)>
<!ELEMENT uncert_semi_major (#PCDATA)>
<!ELEMENT uncert_semi_minor (#PCDATA)>
<!ELEMENT orient_major (#PCDATA)>
<!ELEMENT confidence (#PCDATA)>
<!ELEMENT polygon (coordinate+)>
<!ELEMENT ellipsoid_point_alt (coordinate,altitude)>
<!ELEMENT altitude (height_above_surface,height)>
<!ELEMENT height_above_surface (#PCDATA)>
<!ELEMENT height (#PCDATA)>
<!ELEMENT ellipsoid_point_alt_uncertellipse
(coordinate,altitude,uncert_semi_major,uncert_semi_minor,orient_major,confidence
,uncert_alt)>
<!ELEMENT uncert_alt (#PCDATA)>
<!ELEMENT ellips_arc
(coordinate,inner_rad,uncert_rad,offset_angle,included_angle,confidence)>
<!ELEMENT inner_rad (#PCDATA)>
<!ELEMENT uncert_rad (#PCDATA)>
<!ELEMENT offset_angle (#PCDATA)>
<!ELEMENT included_angle (#PCDATA)>
<!ELEMENT velocity_data
(hor_velocity?,vert_velocity?,vert_velocity_direction?,hor_uncert?,vert_uncert?)
>
<!ELEMENT hor_velocity (#PCDATA)>
<!ELEMENT vert_velocity (#PCDATA)>
<!ELEMENT vert_velocity_direction (#PCDATA)>
<!ELEMENT hor_uncert (#PCDATA)>
<!ELEMENT vert_uncert (#PCDATA)>
]>
<NMEA-string>: string type in UTF-8. This parameter provides an NMEA-string as defined in IEC 61162 [78].
This parameter shall not be subject to conventional character conversion as per +CSCS.
Example: +CMOLRN: "$GPRMC,235947.000,V,0000.0000,N,00000.0000,E,,,041299,,*1D<CR><LF>&"
Implementation
Optional.
8.51 Backlight +CBKLT
Table 8.51-1: +CBKLT parameter command syntax
Command
Possible response(s)
+CBKLT=[<state>[,<duration>]]
+CME ERROR: <err>
+CBKLT? +CBKLT: <state>,[<duration>]
+CME ERROR: <err>
+CBKLT=?
+CBKLT: (list of supported <state>s)
+CME ERROR: <err>
m
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
151
3GPP TS 27.007 version 13.3.0 Release
13
Description
This command is used to enable or disable the backlight of the MT"s main display. The backlight can be enabled
indefinitely or the duration shall be indicated as a specified period of time (in seconds). Refer subclause 9.2 for possible
<err> values.
Read command returns the current state and duration (in seconds) if applicable.
Test command returns supported values as a compound value.
Defined values
<state>: integer type
0 disable
1 enable for the duration specified
2 enable indefinitely
3 enable for a short duration specified by the UE manufacturer
<duration>: integer type. The range (if seconds) is manufacturer specific.
xxxx in seconds
Implementation
Optional.
8.52 Command touch screen action +CTSA
Table 8.52-1: +CTSA action command syntax
Command
Possible response(s)
+CTSA=<action>,<x>,<y>,<id>
[,<duration>] +CME ERROR: <err>
+CTSA=?
+CTSA: (list of supported <action>s)
Description:
This command is used to emulate a touch screen action on the mobile equipment (ME). If emulation fails with an ME
error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
This command should be accepted (OK returned) before actually emulating the touch screen action.
Test command returns the list of supported actions for the mobile equipment.
The top left corner of the touch screen is defined as the 0, 0 point, see figure 8.52-1. This coordinate does not change
regardless of the display mode (portrait or landscape). All coordinate values are non-negative integers.
0,0 // DD <—> CID CID CID CID CID CID CID ETSI
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
152
3GPP TS 27.007 version 13.3.0 Release 13
X
X
Y
Y
0,0
Figure 8.52-1: ME screen outline
Defined values
<action>: integer type
0 Release. Emulates the user releasing the touch screen at the <x>, <y> coordinates.
1 Depress. Emulates the user depressing the touch screen at location <x>, <y>.
NOTE 1: Consecutive Depress actions will emulate dragging a stylus on the touch device to the new location.
2 Single Tap. Emulates the user performing a single tap action at the <x>, <y> location. The timing required
to emulate a single tap shall be handled by the mobile equipment.
3 Double Tap. Emulates the user performing a double tap action at the <x>, <y> location. The timing required
to emulate a double tap shall be handled by the mobile equipment.
<x>: integer type. The horizontal x coordinate location of the action performed on the touch screen.
<y>: integer type. The vertical y coordinate location of the action performed on the touch screen.
<id>: integer type. A positive integer value. If id is a non-zero integer value N, then it represents, or correlates
with, the N
th
simultaneous touch action performed on the touch screen. If id is 0 then the touch screen action is
an initial touch screen action or the touch screen action is correlated with the initial touch action.
NOTE 2: The number of possible simultaneous touch actions is implementation specific.
<duration>: integer type (the value range is in milliseconds from 1 to 65535). Emulates the user releasing the
touch screen at the <x>, <y> coordinates after duration milliseconds. If the value is set to 0, then a duration is
not indicated.
Examples:
ETSI
ETSI TS 127 007 V13.3.0 (
2016
-
03)
153
3GPP TS 27.007 version 13.3.0 Release 13
Table 8.52-2: Examples of syntax for various user actions
User Action
Syntax
Description
Depress
AT+CTSA=1,25,45
This will emulate a user pressing down on the
ME touch screen at the 25, 45 coordinates.
Release
AT+CTSA=0,25,45
This will emulate a user releasing the touch
screen at the 25, 45 coordinates.
Single Tap
AT+CTSA=2,25,45
This will emulate a user single tapping the
touch screen at the 25, 45 coordinates.
Double Tap
AT+CTSA=3,25,45
This will emulate a user double tapping the
touch screen at the 25, 45 coordinates.
Drag
AT+CTSA=1,10,10;
+CTSA=0,50,50
This will emulate a user touching at 10,10,
dragging to 50,50, and releasing.
Draw
AT+CTSA=1,10,10;
+CTSA=1,50,50;
+CTSA=0,100,100
This will emulate a user touching at 10,10,
then dragging to 50,50, then dragging to
100,100 and finally releasing the touch
screen at 100,100.
Multi Touch
AT+CTSA=1,10,10,0;
+CTSA=1,50,50,1;
+CTSA=0,60,60,1;
+CTSA=0,100,100,0
This will emulate a user initiating a first
gesture touching at 10,10, then
simultaneously initiating a second gesture at
50,50, then dragging the second gesture from
50, 50 to 60,60. The user releases the
second gesture at 60. 60 while
simultaneously dragging the first gesture from
10,10 to 100,100 and finally releasing the
touch screen at 100,100.
Long
Depress
AT+CTSA=1,10,10,0;
+CTSA=0,10,10,0,3000
This will emulate a user touching at
coordinates 10,10, and releasing the touch
screen at coordinates 10, 10, after 3 seconds.
Implementation
Optional.
8.53 Command screen orientation +CSO
Table 8.53-1: +CSO parameter command syntax
Command
Possible response(s)
+CSO=<orientation>[,<Current
TopSide>] +CME ERROR: <err>
+CSO? +CSO: <orientation>[,<Current
TopSide>]
+CME ERROR: <err>
+CSO=? +CSO: (list of supported
<orientation>s)
+CME ERROR: <err>
Description
This command is used to set or read back the orientation of the screen on the mobile equipment (ME). The ME may
override the setting via a key press or touch screen action. In addition to setting portrait mode and landscape mode, the
command is used by the TE to set a reference orientation for the screen on the ME. The physical orientation of the ME
shall not override this command. If emulation fails with an ME error, +CME ERROR: <err> is returned. Refer
subclause 9.2 for possible <err> values.
Top=0 Left side:3 Righl sideIl BotIDIYFZ Gm» ity
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
154
3GPP TS 27.007 version 13.3.0 Release 13
Figure 8.53-1: Labelled ME sides when the ME is in the normal operating mode
This command should be accepted (OK returned) before actually performing the action.
Read command returns the current settings.
Test command returns the list of supported orientations for the mobile equipment as a compound value.
Defined values
<orientation>: integer type
0 Portrait. The device is in portrait mode.
1 Landscape. The device is in landscape mode.
2 Any. The top of the ME's screen is identified by <CurrentTopSide> parameter, identifying a side of the
screen of the ME.
<CurrentTopSide>: integer type, representing the label of the side that is the top of the screen. The default
value is manufacturer specific.
0 Top. The ME is in the normal operating mode (see figure 8.53-1).
1 Right side. The side labelled right side is the side that is the top of the screen.
2 Bottom. The side labelled bottom is the side that is the top of the screen.
3 Left side. The side labelled left side is the side that is the top of the screen.
Examples:
Table 8.53-2: Examples of syntax for various actions
Action
Syntax
Description
Get Orientation
AT+CSO?
This will return the current orientation of the
screen device.
Set Orientation
AT+CSO=0
This will set the current orientation of the
screen device to portrait.
Set Orientation
AT+CSO=2,3
The right side is the current top side (e.g. the
top can be determined relative to gravitational
forces) and identifies the TE"s reference
orientation for the screen on the device.
Implementation
Optional.
ETSI
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
155
3GPP TS 27.007 version 13.3.0 Release 13
8.54 Command screen size +CSS
Table 8.54-1: +CSS action command syntax
Command
Possible response(s)
+CSS +CSS: <Max_X>,<Max_Y>
+CME ERROR: <err>
+CSS=?
Description
The execution of this command will get the size (in pixels) of the ME's (touch) screen.
The x-axis and y-axis will be based on a single normal operating mode of the ME, see figure 8.54-1. The 0,0 point will
always be located at the top left corner of the screen in the normal operating mode. Changing the ME's mode from e.g.
portrait mode to landscape mode does not change the physical location of 0,0 or how the x and y axes are interpreted.
If emulation fails with an ME error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err>
values. This command should be accepted (OK returned) before returning the screen size of the device.
X
X
Y
Y
0,0
Figure 8.54-1: ME screen outline
Defined values
<Max_X>: integer type. Must be a positive integer representing the maxium width of the screen.
<Max_Y>: integer type. Must be a positive integer representing the maximum height of the screen
Implementation
Optional.
|xcl
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
156
3GPP TS 27.007 version 13.3.0 Release 13
8.54A Command display screen boundary +CDSB
Table 8.54A-1: +CDSB action command syntax
Command
Possible response(s)
+CDSB +CDSB: <Top_Left_X>,<Top_Le
ft_Y>,<Bottom_Right_X>,<Bot
tom_Right_Y>[,<Width_of_the
_Boundary>]
+CME ERROR: <err>
+CDSB=?
Description
The execution of this command will identify the boundary between a display area and a non-display area of the ME"s
(touch) screen. If the display area of the (touch) screen is the same size as the (touch) screen, the values
<Top_Left_X>, <Top_Left_Y> are set to 0, and the values <Bottom_Right_X>, <Bottom_Right_Y>
match the values returned by the command +CSS (see subclause 8.54).
As in subclause 8.54, the x-axis and y-axis will be based on a single normal operating mode of the ME.
If emulation fails with an ME error, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err>
values.
Defined values
<Top_Left_X>: integer type. Must be a positive integer representing the top left pixel X coordinate of the
boundary.
<Top_Left_Y>: integer type. Must be a positive integer representing the top left pixel Y coordinate of the
boundary.
<Bottom_Right_X>: integer type. Must be a positive integer representing the bottom right pixel X coordinate of
the boundary.
<Bottom_Right_Y>: integer type. Must be a positive integer representing the bottom right pixel Y coordinate of
the boundary.
<Width_of_the_Boundary>: integer type (the value range is in pixels, and starts at 1. The maximum value is
implementation specific). Representing the width of the boundary, by default the width is 1 pixel. If the integer
value is positive, the boundary is part of the display area of the ME's (touch) screen. If the integer value is
negative, the boundary is part of the non-display area of the ME"s (touch) screen.
Implementation
Optional.
8.55 Positioning control +CPOS
Table 8.55-1: +CPOS Action Command Syntax
Command
Possible response(s)
+CPOS<CR>
text is entered <ctrl-Z/ESC>
+CME ERROR: <err>
+CPOS=?
Description
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
157
3GPP TS 27.007 version 13.3.0 Release 13
Execution command causes the TE to enter a transparent mode for sending XML formatted data according to
table 8.55-2: XML DTD for <pos>.
Subsequent to +CPOS:
- the TA shall send a two character sequence <CR><LF> after command line is terminated with <CR>. Then text
can be entered from TE to ME/TA.
- the echoing of entered characters back from the TA is controlled by V.25ter echo command E.
- sending may be cancelled by giving <ESC> character (IRA 27).
- <ctrl-Z> (IRA 26) shall be used to indicate the ending of the message body.
Refer subclause 9.2 for possible <err> values.
Defined events
<location>: string type in UTF-8. This parameter provides an XML-formatted string of GAD-shape positioning
data similar to what is defined in table 8.55-3. This parameter shall not be subject to conventional character
conversion as per +CSCS.
<assist_data>: string type in UTF-8. This parameter provides an XML-formatted string of assistance data as
defined in table 8.55-5. This parameter shall not be subject to conventional character conversion as per +CSCS.
<GPS_meas>: string type in UTF-8. This parameter provides an XML-formatted string of GPS measurement data
as defined in table 8.55-10. This parameter shall not be subject to conventional character conversion as per
+CSCS.
<GNSS_meas>: string type in UTF-8. This parameter provides an XML-formatted string of GPS measurement data
as defined in table 8.55-11 for LPP procedures and GANSS procedures in RRLP and RRC. This parameter shall
not be subject to conventional character conversion as per +CSCS.
<GPS_assist_req>: string type in UTF-8. This parameter provides an XML-formatted string for requesting
GPS assistance data as defined in table 8.55-12. This parameter shall not be subject to conventional character
conversion as per +CSCS.
<Strobe>: string type in UTF-8. This parameter provides an XML-formatted string for triggering the generation
of strobe as defined in table 8.55-25. This parameter shall not be subject to conventional character conversion as
per +CSCS.
<GNSS_assist_req>: string type in UTF-8. This parameter provides an XML-formatted string for requesting
GNSS assistance data as defined in table 8.55-15. This parameter shall not be subject to conventional character
conversion as per +CSCS.
<capability_req> string type in UTF-8. This parameter provides an XML-formatted string for requesting
capability data as defined in table 8.55-4. This parameter shall not be subject to conventional character
conversion as per +CSCS.
<msg>: string type in UTF-8. This parameter provides an XML-formatted string for communicating simple
messages as defined in table 8.55-13. This parameter shall not be subject to conventional character conversion as
per +CSCS.
<pos_err>: string type in UTF-8. This parameter provides an XML-formatted string of positioning error
parameters as defined in table 8.55-14. This parameter shall not be subject to conventional character conversion
as per +CSCS.
<reset_assist_data>: string type in UTF-8. This parameter provides an XML-formatted string for resetting
GNSS/OTDOA assistance data as defined in table 8.55-22. This parameter shall not be subject to conventional
character conversion as per +CSCS.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
158
3GPP TS 27.007 version 13.3.0 Release 13
<OTDOA_ECID_req>: string type in UTF-8. This parameter provides an XML-formatted string for
aborting/requesting location information for OTDOA/ECID method types as defined in table 8.55-23. This
parameter shall not be subject to conventional character conversion as per +CSCS.
NOTE 1: An XML-formatted string intended for +CPOS can be split e.g. in order to prevent that the string becomes
too long. Where to split an XML-formatted string is implementation specific.
<GNSS_provided_location_information>: string type in UTF-8. This parameter provides an XML-
formatted string of GAD-shape positioning data as defined in table 8.55-19. This parameter shall not be subject
to conventional character conversion as per +CSCS.
Table 8.55-2: XML DTD for <pos>
<?xml version="1.0" ?>
<!DOCTYPE pos[
<!ELEMENT pos
(location|GNSS_provided_location_information|assist_data|pos_meas|pos_meas_req|GPS_meas|OTDOA_ECID_r
eq|OTDOA_meas|ECID_meas|GNSS_meas*|GPS_assist_req|GNSS_assist_req|OTDOA_assist_req|capability_req|ca
pabilities|msg|pos_err|reset_assist_data|Strobe)>
<!ATTLIST pos protocol (RRLP|RRC|LPP) #IMPLIED
transaction_id CDATA #IMPLIED>
]>
NOTE 2: The XML DTD for "pos" is the top-level definition of all positioning events, containing elements going
in both directions between the MS and the network. The subelements of "pos" are superset definitions
of the positioning events. A variable amount of these elements can be sent. Sent elements must follow the
rules for the XML, e.g. elements postfixed by "?" can occur zero or more times. The total delivery must
be a complete specification. Sub-elements cannot be delivered without being preceeded with an element
reference from the above level.
Table 8.55-3: XML DTD for <location>
<!ELEMENT location (location_parameters,time_of_fix?,time_assistance?)>
<!ELEMENT time_of_fix (#PCDATA)>
<!ELEMENT time_assistance (GPS_time,(GSM_time|WCDMA_time|LTE_time)?,TimeUnc?)>
NOTE 3: The element "location_parameters" provides one or more XML-formatted strings of GAD-shape
positioning data as defined in table 8.50-2.
NOTE 3a: The elements "time_of_fix" of "location" and "time" of "location_parameters" (see
Table 8.50-2) are both for holding time-stamp of the location information. Due to this, the parameter
"time_of_fix" can be omitted when "time" is present or vice versa.
Table 8.55-4: XML DTD for <capability_req>, <capabilities>
<!ELEMENT capability_req EMPTY>
<!ELEMENT capabilities
(GPS_method?,GNSS_method*,GPS_aid?,GNSS_aid?,OTDOA_capability?,ECID_capability?)>
<!ELEMENT GPS_Method (MSA_sup?,MSB_sup?,Standalone_sup?)>
<!ELEMENT MSA_sup EMPTY>
<!ATTLIST MSA_sup fta_sup CDATA "000"> <!-- as LPP fta-MeasSupport -->
<!ELEMENT MSB_sup EMPTY>
<!ATTLIST MSB_sup fta_sup CDATA "000"
velocity_sup (true|false) "false">
<!ELEMENT Standalone_sup EMPTY>
<!ATTLIST Standalone_sup fta_sup CDATA "000"
<!-- as LPP fta-MeasSupport -->
velocity_sup (true|false) "false">
<!ELEMENT GNSS_Method (MSA_sup?,MSB_sup?,Standalone_sup?)>
<!ATTLIST GNSS_Method supported_signal
(GPS_L1|GPS_L1C|GPS_L2C|GPS_L5|SBAS_L1|GLO_G1|GLO_G2|GLO_G3|BDS_B1I) "GPS_L1">
<!ELEMENT GPS_aid
(almanac_sup?,UTC_model_sup?,ionospheric_sup?,nav_model_sup?,DGPS_sup?,ref_loc_sup?,ref_time_sup?,ac
quisition_sup?,rt_integr_sup?)>
<!ELEMENT almanac_sup EMPTY>
<!ELEMENT UTC_model_sup EMPTY>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
159
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT ionospheric_sup EMPTY>
<!ELEMENT nav_model_sup EMPTY>
<!ELEMENT DGPS_sup EMPTY>
<!ELEMENT ref_loc_sup EMPTY>
<!ELEMENT ref_time_sup EMPTY>
<!ELEMENT acquisition_sup EMPTY>
<!ELEMENT rt_integr_sup EMPTY>
<!ELEMENT GNSS_aid (ionospheric_sup?,ref_loc_sup?,ref_time_sup?,earth_orient_sup?,GNSS_aid_for_on
e_gnss*)>
<!ELEMENT earth_orient_sup EMPTY>
<!ELEMENT GNSS_aid_for_one_gnss
(orbit_sup*,clock_sup*,acquisition_sup?,rt_integr_sup?,GNSS_auxiliary_info_sup?,GNSS_databitassistan
ce_sup?,GNSS_almanac_sup?,GNSS_UTC_model_sup?,BDS_grid_model_sup?)>
<!ATTLIST GNSS_aid_for_one_gnss
gnss_id (SBAS|MGPS|QZSS|Glonass|GPS|BDS) #IMPLIED
sbas_id (WASS|EGNOS|MSAS|GAGAN) #IMPLIED>
<!ELEMENT orbit_sup EMPTY>
<!ATTLIST orbit_sup model (2|3|4|5|6) #REQUIRED>
<!-- 2=GPS NAV, 3=GPS CNAV, 4=Glonass, 5=SBAS, 6=BDS -->
<!ELEMENT clock_sup EMPTY>
<!ATTLIST clock_sup model (2|3|4|5|6) #REQUIRED>
<!ELEMENT GNSS_auxiliary_info_sup EMPTY>
<!ELEMENT GNSS_databitassistance_sup EMPTY>
<!ELEMNT GNSS_almanac_sup (almanac_model)>
<!ELEMENT almanac_model (#PCDATA)> <!-- Integer corresponds to bit string 1-8 where bit
at position if set, means particular almanac model is supported –bit6 set means BDS almanac model is
supported. -->
<!ELEMENT GNSS_UTC_model_sup (utc_model)>
<!ELEMENT utc_model (#PCDATA)> <!-- Integer corresponds to bit string 1-8 where bit at
position if set, means particular UTC model is supported –bit4 set means BDS UTC model is supported
-->
<!ELEMENT BDS_grid_model_sup EMPTY>
<!ELEMENT OTDOA_capability (otdoa_mode,supported_band_list_EUTRA,interFreqRSTDmeasurement-r10?)>
<!ELEMENT otdoa_mode #PCDATA> <!-- Integer corresponds to bit string 1-8 where bit at
position if set, means particular OTDOA mode is supported
bit0 –ue-assisted supported -->
<!ELEMENT supported_band_list_EUTRA (band_EUTRA+)>
<!ELEMENT band_EUTRA (#PCDATA)> <!-- 1..64 -->
<!ELEMENT interFreqRSTDmeasurement-r10 EMPTY>
<!ELEMENT ECID_capability (ECID_measSupported)>
<!ELEMENT ECID_measSupported (#PCDATA)> <!-- Integer corresponds to bit string 1-8 where bit
at position if set, means particular ECID mode is supported bit0–rsrp Supported,bit1-rsrq
Supported,bit2-ueRxTx Supported -->
NOTE 3b: For elements "OTDOA_capability" and "ECID_capability", refer to 3GPP TS 36.355 [115]
(subclause 6.5.1.7) and (subclause 6.5.3.4) respectively.
Table 8.55-5: XML DTD for <assist_data>
<!ELEMENT assist_data
(GPS_assist?,GNSS_assist?,msr_assist_data?,system_info_assist_data?,more_assist_data?,ext_container?
,rel98_assist_data_ext?,rel5_assist_data_ext?,rel7_assist_data_ext?,OTDOA_assist_data?,GNSS_loc_serv
er_err?,OTDOA_loc_server_err?)>
<!ELEMENT GPS_assist
(status_health?,BTS_clock_drift?,ref_time*,location_parameters?,DGPS_corrections?,nav_model_elem*,io
nospheric_model?,UTC_model?,almanac?,acqu_assist*,GPS_rt_integrity?)>
<!ELEMENT status_health (#PCDATA)>
<!ELEMENT BTS_clock_drift (#PCDATA)>
<!ELEMENT ref_time (GPS_time),(GSM_time|WCDMA_time|LTE_time)?,TimeUnc?,GPS_TOW_assist*)>
<!ELEMENT GPS_time (GPS_TOW_msec,GPS_week)>
<!ELEMENT GPS_TOW_msec (#PCDATA)>
<!ELEMENT GPS_week (#PCDATA)>
<!ELEMENT GPS_TOW_assist (sat_id,tlm_word,anti_sp,alert,tlm_res)>
<!ELEMENT sat_id (#PCDATA)>
<!ELEMENT tlm_word (#PCDATA)>
<!ELEMENT anti_sp (#PCDATA)>
<!ELEMENT alert (#PCDATA)>
<!ELEMENT tlm_res (#PCDATA)>
<!ELEMENT DGPS_corrections (sat_id,iode,UDRE,PRC,RRC,delta_PRC2?,delta_RRC2?)>
<!ELEMENT iode (#PCDATA)>
<!ELEMENT UDRE (#PCDATA)>
<!ELEMENT PRC (#PCDATA)>
<!ELEMENT RRC (#PCDATA)>
<!ELEMENT delta_PRC2 (#PCDATA)>
<!ELEMENT delta_RRC2 (#PCDATA)>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
160
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT nav_model_elem (sat_id,sat_status,ephem_and_clock?)>
<!ELEMENT sat_status EMPTY>
<!ATTLIST sat_status literal (NS_NN-U|ES_NN-U|NS_NN|ES_SN|REVD) #REQUIRED>
<!ELEMENT ephem_and_clock
(l2_code,ura,sv_health,iodc,l2p_flag,esr1,esr2,esr3,esr4,tgd,toc,af2,af1,af0,crs,delta_n,m0,cuc,ecc,
cus,power_half,toe,fit_flag,aoda,cic,omega0,cis,i0,crc,omega,omega_dot,idot,derived?)>
<!ELEMENT l2_code (#PCDATA)>
<!ELEMENT ura (#PCDATA)>
<!ELEMENT sv_health (#PCDATA)>
<!ELEMENT iodc (#PCDATA)>
<!ELEMENT l2p_flag (#PCDATA)>
<!ELEMENT esr1 (#PCDATA)>
<!ELEMENT esr2 (#PCDATA)>
<!ELEMENT esr3 (#PCDATA)>
<!ELEMENT esr4 (#PCDATA)>
<!ELEMENT tgd (#PCDATA)>
<!ELEMENT toc (#PCDATA)>
<!ELEMENT af2 (#PCDATA)>
<!ELEMENT af1 (#PCDATA)>
<!ELEMENT af0 (#PCDATA)>
<!ELEMENT crs (#PCDATA)>
<!ELEMENT delta_n (#PCDATA)>
<!ELEMENT m0 (#PCDATA)>
<!ELEMENT cuc (#PCDATA)>
<!ELEMENT ecc (#PCDATA)>
<!ELEMENT cus (#PCDATA)>
<!ELEMENT power_half (#PCDATA)>
<!ELEMENT toe (#PCDATA)>
<!ELEMENT fit_flag (#PCDATA)>
<!ELEMENT aoda (#PCDATA)>
<!ELEMENT cic (#PCDATA)>
<!ELEMENT omega0 (#PCDATA)>
<!ELEMENT cis (#PCDATA)>
<!ELEMENT i0 (#PCDATA)>
<!ELEMENT crc (#PCDATA)>
<!ELEMENT omega (#PCDATA)>
<!ELEMENT omega_dot (#PCDATA)>
<!ELEMENT idot (#PCDATA)>
<!ELEMENT derived EMPTY> <!-- data derived locally, e.g from EE -->
<!ELEMENT ionospheric_model (alfa0,alfa1,alfa2,alfa3,beta0,beta1,beta2,beta3)>
<!ELEMENT alfa0 (#PCDATA)>
<!ELEMENT alfa1 (#PCDATA)>
<!ELEMENT alfa2 (#PCDATA)>
<!ELEMENT alfa3 (#PCDATA)>
<!ELEMENT beta0 (#PCDATA)>
<!ELEMENT beta1 (#PCDATA)>
<!ELEMENT beta2 (#PCDATA)>
<!ELEMENT beta3 (#PCDATA)>
<!ELEMENT UTC_model (a1,a0,tot,wnt,dtls,wnlsf,dn,dtlsf)>
<!ELEMENT a1 (#PCDATA)>
<!ELEMENT a0 (#PCDATA)>
<!ELEMENT tot (#PCDATA)>
<!ELEMENT wnt (#PCDATA)>
<!ELEMENT dtls (#PCDATA)>
<!ELEMENT wnlsf (#PCDATA)>
<!ELEMENT dn (#PCDATA)>
<!ELEMENT dtlsf (#PCDATA)>
<!ELEMENT almanac (wna,alm_elem*)>
<!ELEMENT wna (#PCDATA)>
<!ELEMENT alm_elem
(data_id?,sat_id,alm_ecc,alm_toa,alm_ksii,alm_omega_dot,alm_sv_health,alm_power_half,alm_omega0,alm_
omega,alm_m0,alm_af0,alm_af1)>
<!ELEMENT data_id (#PCDATA)>
<!ELEMENT alm_ecc (#PCDATA)>
<!ELEMENT alm_toa (#PCDATA)>
<!ELEMENT alm_ksii (#PCDATA)>
<!ELEMENT alm_omega_dot (#PCDATA)>
<!ELEMENT alm_sv_health (#PCDATA)>
<!ELEMENT alm_power_half (#PCDATA)>
<!ELEMENT alm_omega0 (#PCDATA)>
<!ELEMENT alm_omega (#PCDATA)>
<!ELEMENT alm_m0 (#PCDATA)>
<!ELEMENT alm_af0 (#PCDATA)>
<!ELEMENT alm_af1 (#PCDATA)>
<!ELEMENT GPS_rt_integrity (bad_satellite_set)>
<!ELEMENT bad_satellite_set (sat_id+)> <!-- 1..16 -->
<!ELEMENT msr_assist_data EMPTY>
<!ELEMENT system_info_assist_data EMPTY>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
161
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT more_assist_data EMPTY>
<!ELEMENT ext_container EMPTY>
<!ELEMENT rel98_assist_data_ext EMPTY>
<!ELEMENT rel5_assist_data_ext EMPTY>
<!ELEMENT rel7_assist_data_ext EMPTY>
<!ELEMENT OTDOA_assist_data (OTDOA_ref_cell_info,OTDOA_neighbour_cell_info_list)>
<!ELEMENT OTDOA_ref_cell_info
(phys_cell_id,cell_global_id,earfcn_ref?,antenna_port_conf?,cp_length,prs_info?)>
<!ELEMENT phys_cell_id (#PCDATA)> <!-- 0..503 -->
<!ELEMENT cell_global_id (plmn_identity,cell_identity)>
<!ELEMENT plmn_identity (mcc,mnc)>
<!ELEMENT mcc (#PCDATA)>
<!ELEMENT mnc (#PCDATA)>
<!ELEMENT cell_identity #PCDATA> <!-- 32-bit extended UTRAN cell ID; in case the cell
ID is shorter, the most significant bits are set to 0. -->
<!ELEMENT earfcn_ref (#PCDATA)> <!-- 0..65535 -->
<!ELEMENT antenna_port_conf EMPTY>
<!ATTLIST antenna_port_conf ports(ports1-or-2|ports4) "ports1-or-2">
<!ELEMENT cp_length EMPTY>
<!ATTLIST cp_length literal(normal|extended) #REQUIRED>
<!ELEMENT prs_info (prs_bandwidth,prs_conf_index,num_dl_frames,prs_muting_info_r9?)>
<!ELEMENT prs_bandwidth EMPTY>
<!ATTLIST prs_bandwidth literal(n6|n15|n25|n50|n75|n100)>
<!ELEMENT prs_conf_index (#PCDATA)> <!-- 0..4095 -->
<!ELEMENT num_dl_frames EMPTY>
<!ATTLIST num_dl_frames literal(sf-1|sf-2|sf-4|sf-6)#REQUIRED>
<!ELEMENT prs_muting_info_r9 muting_info>
<!ATTLIST prs_muting_info_r9 literal(po2-r9|po4-r9|po8-r9|po16-r9) #REQUIRED>
<!ELEMENT muting_info (#PCDATA)>
<!ELEMENT OTDOA_neighbour_cell_info_list (OTDOA_neighbour_freq_info)+>
<!ELEMENT OTDOA_neighbour_freq_info (OTDOA_neighbour_cell_info_element)+>
<!ELEMENT OTDOA_neighbour_cell_info_element
(phys_cell_id,cell_global_id?,earfcn?,cp_length?,prs_info?,antenna_port_conf?,slot_number_offset?,pr
s_subframe_offset?,expected_RSTD,expected_RSTD_uncertainty)>
<!ELEMENT phys_cell_id (#PCDATA)> <!-- 0..503 -->
<!ELEMENT cell_global_id (#PCDATA)>
<!ELEMENT earfcn (#PCDATA)> <!-- 0..65535 -->
<!ELEMENT cp_length EMPTY>
<!ATTLIST cp_length literal(normal|extended) #REQUIRED>
<!ELEMENT prs_info (prs_bandwidth,prs_conf_index,num_dl_frames,prs_muting_info_r9?)>
<!ELEMENT prs_bandwidth EMPTY>
<!ATTLIST prs_bandwidth literal(n6|n15|n25|n50|n75|n100)>
<!ELEMENT prs_conf_index (#PCDATA)> <!-- 0..4095 -->
<!ELEMENT num_dl_frames EMPTY>
<!ATTLIST num_dl_frames literal(sf-1|sf-2|sf-4|sf-6)#REQUIRED>
<!ELEMENT prs_muting_info_r9 muting_info>
<!ATTLIST prs_muting_info_r9 literal(po2-r9|po4-r9|po8-r9|po16-r9) #REQUIRED>
<!ELEMENT muting_info (#PCDATA)>
<!ELEMENT antenna_port_conf EMPTY>
<!ATTLIST antenna_port_conf ports(ports1-or-2|ports4) "ports1-or-2">
<!ELEMENT slot_number_offset (#PCDATA)> <!-- 0..19 -->
<!ELEMENT prs_subframe_offset (#PCDATA)> <!-- 0..1279 -->
<!ELEMENT expected_RSTD (#PCDATA)> <!-- 0..16383 -->
<!ELEMENT expected_RSTD_uncertainty (#PCDATA)> <!-- 0..1023 -->
<!ELEMENT GNSS_loc_server_err _EMPTY>
<!ATTLIST GNSS_loc_server_err literal (undefined_error|
undelivered_assistance_data_not_supported|
undelivered_assistance_data_supported_but_currently_not_available|undelivered_assistance_data_is_par
tly_not_supported_and_partly_not_available) #REQUIRED>
<!ELEMENT OTDOA_loc_server_err _EMPTY>
<!ATTLIST OTDOA_loc_server_err literal (undefined_error|assistance_data_not_supported|
assistance_data_supported_but_currently_not_available) #REQUIRED>
NOTE 4: For the elements and the value ranges of assistance data information delivered from the network, refer to
3GPP TS 25.331 [74] (subclause 10.3.7.90), 3GPP TS 36.355 [115] (subclause 6.5.1) and
3GPP TS 44.031 [79] (subclause A.4.2.4). The value ranges of the relevant parameters are described in
the ASN.1 syntax.
NOTE 5: For the element "location_parameters", see table 8.50-2. In the context of this XML, the
"location_parameters" will describe a reference location.
NOTE 6: The elements ext_container, rel98_assist_data_ext, rel5_assist_data_ext and rel7_assist_data_ext are
depreciated.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
162
3GPP TS 27.007 version 13.3.0 Release 13
Table 8.55-6: XML DTD for <GSM_time>, <WCDMA_time>, <LTE_time>, <TimeUnc>
<!ELEMENT GSM_time (frame_number,frame_number_msb,time_slot_number,bit_number,BCCH_carrier?,BSIC?)>
<!ELEMENT frame_number (#PCDATA)>
<!ELEMENT frame_number_msb (#PCDATA)>
<!ELEMENT time_slot_number (#PCDATA)>
<!ELEMENT bit_number (#PCDATA)>
<!ELEMENT BCCH_carrier (#PCDATA)>
<!ELEMENT BSIC (#PCDATA)>
<!ELEMENT WCDMA_time (cell_timing_chips,(FDD_CPICH|TDD_cell_id|SFN),SFN_TOW_Unc?)>
<!ELEMENT cell_timing_chips (#PCDATA)>
<!ELEMENT FDD_CPICH (#PCDATA)>
<!ELEMENT TDD_cell_id (#PCDATA)>
<!ELEMENT SFN (#PCDATA)>
<!ELEMENT SFN_TOW_Unc (#PCDATA)> <!-- Integer 0..1 0- Uncertainity less than 10 ms, 1-
Uncertainity more than 10 ms -->
<!ELEMENT LTE_time (secFromFrameStructStart,fractSecFromFrameStructStart,
frameDrift?,physCellId,cellGlobalIdEUTRA?,earfcn,TimeUnc)>
<!ELEMENT secFromFrameStructStart (#PCDATA)> <!-- 0..12533 -->
<!ELEMENT fractSecFromFrameStructStart (#PCDATA)> <!-- 0..3999999 -->
<!ELEMENT frameDrift (#PCDATA)> <!-- -64..63 -->
<!ELEMENT physCellId (#PCDATA)>
<!ELEMENT cellGlobalIdEUTRA (#PCDATA)>
<!ELEMENT earfcn (#PCDATA)>
<!ELEMENT TimeUnc EMPTY>
<!ATTLIST TimeUnc
Value CDATA "127"
units (s|ms|us|rrlp_k|rrc_k|lpp_k) "rrc_k">
Table 8.55-7: XML DTD for <acqu_assist>
<!ELEMENT acqu_assist (tow_msec,sat_info*,confidence_r10?)>
<!ELEMENT tow_msec (#PCDATA)>
<!ELEMENT sat_info
(sat_id,dopl0,dopl_extra?,code_ph,code_ph_int,GPS_bitno,srch_w,az_el?,doppler_uncertainty_ext_r10?)>
<!ELEMENT dopl0 (#PCDATA)>
<!ATTLIST dopl0 units (rrlp|rrc|lpp|Hz|mps) "rrlp">
<!-- rrlp gps is 2.5 Hz -->
<!-- rrc gps is 2.5 Hz -->
<!-- lpp gnss is 0.5 m/s -->
<!ELEMENT dopl_extra (dopl1,dopl1_uncert)>
<!ELEMENT dopl1 (#PCDATA)>
<!ATTLIST dopl1 units (rrlp|rrc|lpp) "rrlp">
<!-- rrlp is 1/42 Hz/s -->
<!-- rrc is 0.023 Hz/s -->
<!-- lpp is 1/210 m/s/s -->
<!ELEMENT dopl1_uncert EMPTY>
<!ATTLIST dopl1_uncert literal (hz12-5|hz25|hz50|hz100|hz200) #REQUIRED>
<!ELEMENT code_ph (#PCDATA)>
<!ATTLIST code_ph units (chips|ms) "chips">
<!-- chips used for GPS in RRLP and RRC, ms used for LPP -->
<!ELEMENT code_ph_int (#PCDATA)>
<!ELEMENT GPS_bitno (#PCDATA)>
<!ELEMENT srch_w (#PCDATA)>
<!ELEMENT az_el (az,elev)>
<!ELEMENT az (#PCDATA)>
<!ATTLIST az_el units (rrlp|lpp|degree) "rrlp">
<!-- rrlp and rrc have units of 11.25 degree -->
<!-- lpp has units of 0.703125 degrees -->
<!ELEMENT elev (#PCDATA)>
<!ELEMENT doppler_uncertainty_ext_r10>
<!ATTLIST doppler_uncertainty_ext_r10 (d60|d80|d100|d120|no_information) #IMPLIED>
<!ELEMENT confidence_r10 (#PCDATA)> <!-- 0..100 -->
NOTE 7: Units of mps, lpp and ms are used with GNSS procedures.
Table 8.55-8: XML DTD for <pos_meas>
<!ELEMENT pos_meas (meas_abort|RRLP_meas|RRC_meas)>
<!ELEMENT meas_abort EMPTY>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
163
3GPP
TS 27.007 version 13.3.0 Release 13
<!ELEMENT RRLP_meas (RRLP_pos_instruct)>
<!ELEMENT RRLP_pos_instruct (RRLP_method_type,RRLP_method,resp_time_seconds,mult_sets)>
<!ELEMENT RRLP_method_type
(ms_assisted|ms_assisted_no_accuracy|ms_based|ms_based_pref|ms_assisted_pref)>
<!ELEMENT ms_assisted (method_accuracy)>
<!ELEMENT method_accuracy (#PCDATA)>
<!ELEMENT ms_assisted_no_accuracy EMPTY>
<!ELEMENT ms_based (method_accuracy)>
<!ELEMENT ms_based_pref (method_accuracy)>
<!ELEMENT ms_assisted_pref (method_accuracy)>
<!ELEMENT RRLP_method EMPTY>
<!ATTLIST RRLP_method literal (gps) #REQUIRED>
<!ELEMENT resp_time_seconds (#PCDATA)>
<!ELEMENT mult_sets EMPTY>
<!ATTLIST mult_sets literal (multiple|one) #REQUIRED>
<!ELEMENT RRC_meas (rep_quant,rep_crit)>
<!ELEMENT rep_quant (RRC_method_type,RRC_method,hor_acc?,vert_acc?)>
<!ATTLIST rep_quant
gps_timing_of_cell_wanted (true|false) "false"
addl_assist_data_req (true|false) #REQUIRED>
<!ELEMENT RRC_method_type EMPTY>
<!ATTLIST RRC_method_type literal (ue_assisted|ue_based|ue_based_pref|ue_assisted_pref)
#REQUIRED>
<!ELEMENT RRC_method EMPTY>
<!ATTLIST RRC_method literal (otdoa|gps|otdoaOrGPS|cellID) #REQUIRED>
<!ELEMENT hor_acc (#PCDATA)>
<!ELEMENT vert_acc (#PCDATA)>
<!ELEMENT rep_crit (no_rep|event_rep_crit|period_rep_crit)>
<!ELEMENT no_rep EMPTY>
<!ELEMENT event_rep_crit (event_par*)>
<!ELEMENT event_par (rep_amount,meas_interval,event_specific_info?)>
<!ATTLIST event_par report_first_fix (true|false) #REQUIRED>
<!ELEMENT rep_amount EMPTY>
<!ATTLIST rep_amount literal (ra1|ra2|ra4|ra8|ra16|ra32|ra64|ra-Infinity)
#REQUIRED>
<!ELEMENT meas_interval EMPTY>
<!ATTLIST meas_interval literal (e5|e15|e60|e300|e900|e1800|e3600|e7200)
#REQUIRED>
<!ELEMENT event_specific_info (tr_pos_chg|tr_SFN_SFN_chg|tr_SFN_GPS_TOW)>
<!ELEMENT tr_pos_chg EMPTY>
<!ATTLIST tr_pos_chg literal
(pc10|pc20|pc30|pc40|pc50|pc100|pc200|pc300|pc500|pc1000|pc2000|pc5000|pc10000|pc20000|pc50000|pc100
000) #REQUIRED>
<!ELEMENT tr_SFN_SFN_chg EMPTY>
<!ATTLIST tr_SFN_SFN_chg literal (c0-25|c0-
5|c1|c2|c3|c4|c5|c10|c20|c50|c100|c200|c500|c1000|c2000|c5000) #REQUIRED>
<!ELEMENT tr_SFN_GPS_TOW EMPTY>
<!ATTLIST tr_SFN_GPS_TOW literal (ms1|ms2|ms3|ms5|ms10|ms20|ms50|ms100)
#REQUIRED>
<!ELEMENT period_rep_crit EMPTY>
<!ATTLIST period_rep_crit rep_amount (ra1|ra2|ra4|ra8|ra16|ra32|ra64|ra-Infinity) "ra-
Infinity">
<!ATTLIST period_rep_crit rep_interval_long (ril0|ril0-25|ril0-
5|ril1|ril2|ril3|ril4|ril6|ril8|ril12|ril16|ril20|ril24|ril28|ril32|ril64) #REQUIRED>
NOTE 8: For the elements and the value ranges of position measurements data, refer to 3GPP TS 25.331 [74]
(subclause 10.3.7.100) and 3GPP TS 44.031 [79] (subclause A.2). The value ranges of the relevant
parameters are described in the ASN.1 syntax.
Table 8.55-9: XML DTD for <pos_meas_req>
<!-- Alternative to pos_meas, supports RRLP, RRC and LPP -->
<!ELEMENT pos_meas_req (abort|(req_info,qos,loc_coordinate_types?))>
<!ATTLIST pos_meas_req aid_req_allowed (yes|no) #IMPLIED> <!-- Present for RRC and LPP
procedures -->
<!ELEMENT abort EMPTY)>
<!ELEMENT req_info (GNSS_allowed_methods?)>
<!ATTLIST req_info loc_info_type (loc_req|meas_req|loc_pref|MSB_req|MSA_req|MSB_pref|MSA_pref)
"loc_req"
velocity_req (true|false) "false"
time_req (true|false) "false"
multiple_sets (yes|no) "no"
additional_info (yes|no) "no"> <!-- lpp only --> <!-- MSB synonomous with loc_req -->
<!ELEMENT GNSS_allowed_methods
(gps_method?,sbas_method?,qzss_method?,glonass_method?,BDS_method?)>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
164
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT gps_method EMPTY>
<!ELEMENT sbas_method EMPTY>
<!ELEMENT qzss_method EMPTY>
<!ELEMENT glonass_method EMPTY>
<!ELEMENT BDS_method EMPTY>
<!ELEMENT qos (response_time?,(reporting_interval,amount)?,hacc?,vacc?)>
<!-- The presence of reporting_interval implies a periodic procedure -->
<!-- The absence of reporting_interval implies a one-shot procedure -->
<!ELEMENT response_time(time,responseTimeEarlyFix-r12?)
<!ELEMENT time (#PCDATA)> <!-- 1..128 -->
<!ELEMENT responseTimeEarlyFix-r12(#PCDATA)> <!-- 1..128,value of responseTimeEarlyFix-r12
should be less than time -->
<!ELEMENT reporting_interval EMPTY>
<!ATTLIST reporting_interval
ri_exp (ril1|ril2|ril3|ril4|ril6|ril8|ril12|ril16|ril20|ril24|ril28|ril32|ril64) "ril20" >
<!ELEMENT amount EMPTY>
<!ATTLIST amount amount (ra1|ra2|ra4|ra8|ra16|ra32|ra64|ra-Infinity) "ra-Infinity">
<!ELEMENT hacc EMPTY>
<!ATTLIST hacc
accuracy_k CDATA #IMPLIED
confidence CDATA #IMPLIED>
<!ELEMENT vacc EMPTY>
<!ATTLIST vacc
accuracy_k CDATA #IMPLIED
confidence CDATA #IMPLIED>
<ELEMENT loc_coordinate_types(#PCDATA)>
<!-- Integer corresponds to bit string 1-8 where bit at position if set, means location co-
ordinate type is supported bit0-ellipsoidPoint supported,bit1-ellipsoidPointWithUncertaintyCircle
supported,bit2-ellipsoidPointWithUncertaintyEllipse supported,bit3-polygon
supported,bit4ellipsoidPointWithAltitude
supported,bit5ellipsoidPointWithAltitudeAndUncertaintyEllipsoid supported,bit6-ellipsoidArc
supported -->
Table 8.55-10: XML DTD for <GPS_meas>
<!ELEMENT GPS_meas (ref_time_only,meas_params*)>
<!ELEMENT ref_time_only (tow_msec)>
<!ELEMENT meas_params (sat_id,carr2_noise,dopl,whole_chips,fract_chips,multi_path,psr_rms_err)>
<!ELEMENT carr2_noise (#PCDATA)>
<!ELEMENT dopl (#PCDATA)>
<!ELEMENT whole_chips (#PCDATA)>
<!ELEMENT fract_chips (#PCDATA)>
<!ELEMENT multi_path EMPTY>
<!ATTLIST multi_path literal (not_measured|low|medium|high) #REQUIRED>
<!ELEMENT psr_rms_err (#PCDATA)>
NOTE 9: For the elements and the value ranges of GPS measurement data, refer to 3GPP TS 25.331 [74]
(subclause 10.3.7.93) and 3GPP TS 44.031 [79] (subclause A.3.2.5). The value ranges of the relevant
parameters are described in the ASN.1 syntax.
Table 8.55-11: XML DTD for <GNSS_meas>
<!ELEMENT GNSS_meas (sat_meas_params_gnss*,TOD_ms|ref_time_only,earlyFixReport-r12?)>
<!ATTLIST GNSS_meas gnss_id GPS|SBAS|QZSS|Galileo|Glonass|BDS) "GPS">
<!ELEMENT sat_meas_params_gnss
(sat_id,code_phase_ambiguity?,carr2_noise,doppler_mps?,code_phase_ms?,integer_code_phase?,multi_path
,psr_rms_err,adr?,whole_chips?,fract_chips?)>
<!ATTLIST sat_meas_params_gnss measured_signal (GPS_L1|GPS_L1C|GPS_L2C|GPS_L5|SBAS_L1|GLO_G1|G
LO_G2|GLO_G3|BDS_B11) "GPS_L1">
<!ELEMENT code_phase_ambiguity (#PCDATA)> <!-- 0..127 -->
<!ELEMENT doppler_mps (#PCDATA)> <!-- m/s Range -32768..32767 -->
<!ELEMENT code_phase_ms (#PCDATA)> <!-- ms Range 0..2097151 -->
<!ELEMENT integer_code_phase (#PCDATA)>
<!ELEMENT adr (#PCDATA)>
<!ELEMENT TOD_ms (#PCDATA)> <!-- time of day in ms in decimal to 5 decimal places. Format
#######.##### -->
<!ATTLIST TOD_ms gnss_time_id (GPS|Glonass|QZSS|BDS) "GPS">
<!ELEMENT earlyFixReport-r12 EMPTY>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
165
3GPP TS 27.007 version 13.3.0 Release 13
NOTE 10: "GNSS_meas" is used for reporting measurements results for GNSS procedures i.e. procedures where:
"GNSS_allowed_methods", "GNSS_assist" was received or where "acqu_assist" uses
units of ms.
NOTE 10a:."ref_time_only" shall be provided by the TE for gnss_id="GPS", refer to
3GPP TS 25.331 [74] (subclause 10.3.7.93) and 3GPP TS 44.031 [79] (subclause A.3). Usage of the
element "GNSS_meas" in "GNSS_provided_location_information" can be omitted as
"GNSS_meas" is already present in "pos".
NOTE 10b: "whole_chips" and "fract_chips" to be provided for gnss_id= "GPS"
Table 8.55-12: XML DTD for <GPS_assist_req>
<!ELEMENT GPS_assist_req (nav_addl_data?)>
<!ATTLIST GPS_assist_req
alm_req (true|false) "false"
UTC_model_req (true|false) "false"
ion_req (true|false) "false"
nav_model_req (true|false) "false"
DGPS_corr_req (true|false) "false"
ref_loc_req (true|false) "false"
ref_time_req (true|false) "false"
aqu_assist_req (true|false) "false"
rt_integr_req (true|false) "false">
<!ELEMENT nav_addl_data (GPS_week,GPS_toe,ttoe_limit,addl_req_sat*)>
<!ELEMENT GPS_toe (#PCDATA)>
<!ELEMENT ttoe_limit (#PCDATA)>
<!ELEMENT addl_req_sat (sat_id,iode)>
NOTE 11: For requesting assistance data, refer to 3GPP TS 25.331 [74] (subclause 10.3.7.88a) and
3GPP TS 49.031 [80] (subclause 10.10).
Table 8.55-13: XML DTD for <msg>
<!ELEMENT msg EMPTY>
<!ATTLIST msg status (assist_data_delivered) #REQUIRED>
NOTE 12: "assist_data_delivered" can be used as an indication of completion of provision of assistance
data.
Table 8.55-14: XML DTD for <pos_err>
<!ELEMENT pos_err (err_reason,GPS_assist_req?,ECID_meas_error_cause?,GNSS_assist_req?)>
<!ELEMENT err_reason_EMPTY>
<!ATTLIST err_reason literal
(undefined_error|not_enough_gps_satellites|gps_assist_data_missing|gnss_assist_data_missing|not_enou
gh_gnss_satellites|OTDOA_undefined|OTDOA_assistance_data_missing|OTDOA_unable_to_measure_referencece
ll|OTDOA_unable_to_measure_any_neighbourcell|OTDOA_attempted_but_unable_to_measure_some_neighbourcel
ls|ECID_undefined|ECID_requested_measurement_not_available|ECID_not_all_requested_measurements_possi
ble) #REQUIRED>
<!ELEMENT ECID_meas_error_cause (#PCDATA)> <!-- Integer corresponds to bit string 1-8 where bit
at position represents ECID error cause. Only applicable, when value of err_reason =
'ECID_not_all_requested_measurements_possible' bit0–rsrpMeasurementNotPossible, bit1-
rsrqMeasurementNotPossible, bit2-ueRxTxMeasurementNotPossible -->
NOTE 13: For reporting positioning error, refer to 3GPP TS 25.331 [74] (subclause 10.3.7.87) and
3GPP TS 44.031 [79] (subclause A.3.2.6).
NOTE 13a:For reporting GNSS related positioning errors, refer to 3GPP TS 36.355 [115] (subclause 6.5.2.12) for
LPP, 3GPP TS 25.331 [74] (subclause 10.3.7.87) for RRC and 3GPP TS 44.031 [79] (subclause A.3.2.6)
for RRLP.
NOTE 13b: For reporting OTDOA and ECID errors, refer to 3GPP TS 36.355 [115] (subclause 6.5.1.9) for OTDOA
specific errors and 3GPP TS 36.355 [115] (subclause 6.5.3.6) for ECID specific errors.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
166
3GPP TS 27.007 version 13.3.0 Release 13
Table 8.55-15: XML DTD for <GNSS_assist>, <GNSS_assist_req>
<!ELEMENT GNSS_assist
(GNSS_ref_time?,GNSS_ref_location?,GNSS_ref_measurment_assist?,GNSS_ionospheric_model?,GNSS_earth_or
ient_param?,GNSS_additional_ion_model?,GNSS_time_model,GNSS_nav_model?,GNSS_integrity?,acqu_assist*,
GNSS_databitassistance?,GNSS_almanac?,GNSS_UTC_model?,BDS-GridModel-r12?,GNSS_auxiliary_info?)>
<!ATTLIST GNSS_assist
gnss_id (SBAS|MGPS|QZSS|Glonass|GPS|BDS) #IMPLIED
sbas_id (WASS|EGNOS|MSAS|GAGAN) #IMPLIED>
<!ELEMENT GNSS_ref_time (GNSS_day,GNSS_TOD_s,notification_leap_sec)>
<!ATTLIST GNSS_ref_time gnss_time_id (GPS|Glonass|QZSS|BDS) #REQUIRED>
<!ELEMENT GNSS_day (#PCDATA)>
<!ELEMENT GNSS_TOD_s (#PCDATA)> <!-- seconds -->
<!-- 0..86399 for RRLP; 0.000 to 86399.999 for LPP with ms -->
<!-- TOD Uncertainty presented in TimeUnc -->
<!ELEMENT notification_leap_sec (#PCDATA) > <!-- hex LPP only -->
<!ELEMENT GNSS_ref_location (location_parameters)>
<!ELEMENT GNSS_ref_measurment_assist (acqu_assist)>
<!ELEMENT GNSS_ionospheric_model (gnss_ion_ai0,gnss_ion_ai1,gnss_ion_ai2,gnss_ion_flags?)>
<!ELEMENT gnss_ion_ai0 (#PCDATA)> <!-- range 0..4095 -->
<!ELEMENT gnss_ion_ai1 (#PCDATA)> <!-- range 0..4095 -->
<!ELEMENT gnss_ion_ai2 (#PCDATA)> <!-- range 0..4095 -->
<!ELEMENT gnss_ion_flags EMPTY>
<!ATTLIST gnss_ion_flags
storm_flag1 (0|1) "0"
storm_flag2 (0|1) "0"
storm_flag3 (0|1) "0"
storm_flag4 (0|1) "0"
storm_flag5 (0|1) "0">
<!ELEMENT GNSS_earth_orient_param
(gnss_eop_teop,gnss_eop_pmX,gnss_eop_pmX_d,gnss_eop_pmY,gnss_eop_pmY_d,gnss_eop_deltaUT1,gnss_eop_de
ltaUT1_d)>
<!ELEMENT gnss_eop_teop (#PCDATA)> <!-- range 0..65535 -->
<!ELEMENT gnss_eop_pmX (#PCDATA)> <!-- range -1048576..1048575 -->
<!ELEMENT gnss_eop_pmX_d (#PCDATA)> <!-- range -16384..16383 -->
<!ELEMENT gnss_eop_pmY (#PCDATA)> <!-- range -1048576..1048575 -->
<!ELEMENT gnss_eop_pmY_d (#PCDATA)> <!-- range -16384..16383 -->
<!ELEMENT gnss_eop_deltaUT1 (#PCDATA)> <!-- range -1073741824..1073741823 -->
<!ELEMENT gnss_eop_deltaUT1_d (#PCDATA)> <!-- range -262144..262143 -->
<!ELEMENT GNSS_additional_ion_model (ionospheric_model)>
<!ATTLIST GNSS_additional_ion_model
ion_model_data_id (00|11|01) "00"> <!-- from rrlp 11=QZSS 00=other 01=BDS -->
<!ELEMENT GNSS_time_model (tme_ref_time,tme_A0,tme_A1?,tme_A2?,tme_week?)>
<!ATTLIST GNSS_time_model gnss_time_id (GPS|Glonass|QZSS|BDS) #REQUIRED>
<!ELEMENT tme_ref_time (#PCDATA)> <!-- sec scale 2**4 -->
<!ELEMENT tme_A0 (#PCDATA)> <!—sec scale 2**-35 -->
<!ELEMENT tme_A1 (#PCDATA)> <!-- sec/sec scale 2**-51 -->
<!ELEMENT tme_A2 (#PCDATA)> <!-- sec/sec sec scale 2**-68 -->
<!ELEMENT tme_week (#PCDATA)> <!-- 0..8191 -->
<!ELEMENT GNSS_nav_model (GNSS_satelite+)>
<!ATTLIST GNSS_nav_model
non_broadcast_ind_flag (0|1) "0">
<!ELEMENT GNSS_satelite (sat_id,nms_health,nms_iod,
((nms_clock_nav,nms_orbit_nav)|
(nms_clock_cnav,nms_orbit_cnav)|
(nms_clock_glonass,nms_orbit_glonass)|
(nms_clock_sbas,nms_orbit_sbas)|
(nms_clock_bds,nms_orbit_bds)))>
<!ELEMENT nms_health (#PCDATA)> <!-- in hexadecimal -->
<!ELEMENT nms_iod (#PCDATA)> <!-- includes iod_msb -->
<!ELEMENT GNSS_integrity (bad_signal*)>
<!ELEMENT bad_signal (sat_id,GNSS_signal?)>
<!ELEMENT GNSS_signal (#PCDATA)>
<!ELEMENT GNSS_databitassistance (gnss-TOD,gnss-TODfrac?,gnss-DataBitsSatList+)>
<!ELEMENT gnss-TOD (#PCDATA)> <!-- 0..3599 -->
<!ELEMENT gnss-TODfrac (#PCDATA)> <!-- 0..99 -->
<!ELEMENT gnss-DataBitsSatList(sat_id,gnss-DataBitsSgnList+)>
<!ATTLIST gnss-DataBitsSatList signal_id
(GPS_L1|GPS_L1C|GPS_L2C|GPS_L5|SBAS_L1|GLO_G1|GLO_G2|GLO_G3|BDS_B1I) "GPS_L1">
<!ELEMENT gnss-DataBitsSgnList (GNSS_databits)> <>
<!ELEMENT GNSS_databits (#PCDATA)> <!-- 1..1024 -->
<!ELEMENT GNSS_almanac(week_number?,toa,ioda?,completeAlmanacProvided,gnss-AlmanacList+)>
<!ELEMENT week_number (#PCDATA)> <!-- 0..255 -->
<!ELEMENT toa (#PCDATA)> <!-- 0..255 -->
<!ELEMENT ioda(#PCDATA)> <!-- 0..3 -->
<!ELEMENT completeAlmanacProvided (#PCDATA)>
<!ELEMENT gnss-AlmanacList(keplerianBDS-Almanac-r12)>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
167
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT keplerianBDS-Almanac-r12(sat_id,bdsAlmToa-r12?,bdsAlmSqrtA-r12,bdsAlmE-r12,bdsAlmW-
r12,bdsAlmM0-r12,bdsAlmOmega0-r12,bdsAlmOmegaDot-r12,bdsAlmDeltaI-r12,bdsAlmA0-r12,bdsAlmA1-
r12,bdsSvHealth-r12?)>
<!ELEMENT bdsAlmToa-r12 (#PCDATA)> <!-- 0..256 -->
<!ELEMENT bdsAlmSqrtA-r12 (#PCDATA)> <!-- 0..16777215 -->
<!ELEMENT bdsAlmE-r12 (#PCDATA)> <!-- 0..131071 -->
<!ELEMENT bdsAlmW-r12 (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT bdsAlmM0-r12 (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT bdsAlmOmega0-r12(#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT bdsAlmOmegaDot-r12 (#PCDATA)> <!-- -65536..65535 -->
<!ELEMENT bdsAlmDeltaI-r12 (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT bdsAlmA0-r12 (#PCDATA)> <!-- -1024..1023 -->
<!ELEMENT bdsAlmA1-r12 (#PCDATA)> <!-- -1024..1023 -->
<!ELEMENT bdsSvHealth-r12(#PCDATA)> <!-- 0..3599 -->
<!ELEMENT GNSS_UTC_model (utcModel5-r12)>
<!ELEMENT utcModel5-r12 (utcA0-r12,utcA1-r12,utcDeltaTls-r12,utcWNlsf-r12,utcDN-r12,utcDeltaTlsf-
r12)>
<!ELEMENT utcA0-r12 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT utcA1-r12 (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT utcDeltaTls-r12 (#PCDATA)> <!-- -128..127 -->
<!ELEMENT utcWNlsf-r12 (#PCDATA)> <!-- 0..255 -->
<!ELEMENT utcDN-r12(#PCDATA)> <!-- 0..255 -->
<!ELEMENT utcDeltaTlsf-r12 (#PCDATA)> <!-- -128..127 -->
<!ELEMENT BDS-GridModel-r12(bds-RefTime-r12,gridIonList-r12+)>
<!ELEMENT bds-RefTime-r12 (#PCDATA)> <!-- 0..3599 -->
<!ELEMENT gridIonList-r12 (igp-ID-r12,dt-r12,givei-r12)>
<!ELEMENT igp-ID-r12 (#PCDATA)> <!-- 1..320 -->
<!ELEMENT dt-r12 (#PCDATA)> <!-- 0..511 -->
<!ELEMENT givei-r12 (#PCDATA)> <!-- 0..15 -->
<!ELEMENT GNSS_auxiliary_info (GNSS_id_glonass)>
<!ELEMENT GNSS_id_glonass (GNSS_id_glonass_sat_element+)>
<!ELEMENT GNSS_id_glonass_sat_element (sat_id,GNSS_signal_id,channel_number?)> <!-- sat_id
0..63 -->
<!ELEMENT GNSS_signal_id (#PCDATA)>
<!-- Integer corresponds to bit string 1-8 where bit at position if set, means particular signal is
addressed; a zero-value at the particular bit position means the signal is not addressed --
> <!ELEMENT channel_number (#PCDATA)> <!-- -7..13 -->
<!ELEMENT GNSS_assist_req (GNSS_assist_req_per_gnss*)>
<!-- common assist req -->
<!ELEMENT GNSS_ref_time_req EMPTY>
<!ATTLIST GNSS_ref_time_req
time_req_pref (SBAS|MGPS|QZSS|Glonass|GPS) #IMPLIED
tow_req (false|true) "false"
leap_sec_req (false|true) #IMPLIED>
<!ELEMENT GNSS_ref_loc_req EMPTY>
<!ELEMENT GNSS_ion_model_req EMPTY>
<!ELEMENT GNSS_earth_orient_req EMPTY>
<!-- generic req -->
<!ELEMENT GNSS_assist_req_per_gnss
(GNSS_time_model_req?,GNSS_navigation_model_req?,GNSS_integrity_req?,GNSS_acquisition_req?,GNSS_auxi
liary_info_req?,GNSS_databitassistance_req?,GNSS_Almanac_req?,GNSS_UTC_model_req?,BDS_grid_model_req
_r12?)>
<!ATTLIST GNSS_assist_req_per_gnss
gnss_id (SBAS|MGPS|QZSS|Glonass|GPS) #REQUIRED
sbas_id (WASS|EGNOS|MSAS|GAGAN) #IMPLIED>
<!ELEMENT GNSS_time_model_req EMPTY>
<!-- For LPP gnss-TO-IDsReq is derived from gnss_id -->
<!ATTLIST GNSS_time_model_req delta_T_req (false|true) #IMPLIED>
<!ELEMENT GNSS_navigation_model_req (stored_nav_list?,requested_nav_list?) >
<!ELEMENT stored_nav_list
(snl_week_or_day,snl_toe,snl_toe_limit,stored_sat_list_element*,requested_nav_list?)>
<!ELEMENT snl_week_or_day (#PCDATA)>
<!ELEMENT snl_toe (#PCDATA)>
<!ELEMENT snl_toe_limit (#PCDATA)>
<!ELEMENT stored_sat_list_element EMPTY>
<!ATTLIST stored_sat_list_element
stored_id CDATA #REQUIRED
stored_iod CDATA #REQUIRED
stored_clock_model (2|3|4|5|6) #IMPLIED
stored_orbit_model (2|3|4|5|6) #IMPLIED>
<!ELEMENT requested_nav_list (requested_nav_list_info*)>
<!ELEMENT requested_nav_list_info EMPTY>
<!ATTLIST requested_nav_list_info
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
168
3GPP TS 27.00
7 version 13.3.0 Release 13
requested_sv CDATA "00000000ffffffff"
requested_clock_model (2|3|4|5|6) #IMPLIED
requested_orbit_model (2|3|4|5|6) #IMPLIED
requested_add_nav_param (false|true) #IMPLIED>
<!-- requested_sv is a bit string in hexidecimal, needed for LPP -->
<!ELEMENT GNSS_integrity_req EMPTY>
<!ELEMENT GNSS_acquisition_req EMPTY>
<!ATTLIST GNSS_acquisition_req signal
(GPS_L1|GPS_L1C|GPS_L2C|GPS_L5|SBAS_L1|GLO_G1|GLO_G2|GLO_G3|BDS_B1I) "GPS_L1">
<!ELEMENT GNSS_databitassistance_req
(gnss_TOD_req,gnss_TOD_fraq?,databit_interval,databit_reqsat_list+)>
<!ATTLIST GNSS_databitassistance_req signal
(GPS_L1|GPS_L1C|GPS_L2C|GPS_L5|SBAS_L1|GLO_G1|GLO_G2|GLO_G3|BDS_B1l) "GPS_L1">
confidence_support (yes|no) #IMPLIED
doppler_uncertainty_ext_support(yes|no) #IMPLIED>
<!ELEMENT GNSS_auxiliary_info_req EMPTY>
<!ELEMENT gnss_TOD_req (#PCDATA)> <!-- 0..3599 -->
<!ELEMENT gnss_TOD_fraq (#PCDATA)> <!-- 0..599 -->
<!ELEMENT databit_interval (#PCDATA)> <!-- 0..15 -->
<!ELEMENT databit_reqsat_list (sat_id)> <!-- sat_id 0..63 -->
<!ELEMENT GNSS_Almanac_req >
<!ATTLIST GNSS_Almanac_req model (7)#IMPLIED>
<!ELEMENT GNSS_UTC_model_req >
<!ATTLIST GNSS_UTC_model_req model (5)#IMPLIED>
<!ELEMENT BDS_grid_model_req_r12 EMPTY>
NOTE 14: GNSS_assist is used for assistance data received via an RRLP ASN.1 GANSSAssistanceSet element
(refer to 3GPP TS 44.031 [79]), via an RRC GANSS assistance data element (refer to
3GPP TS 25.331 [74] subclause 10.3.7.90b) or via LPP.
NOTE 14a: The element "GNSS_ref_measurement_assist" of "GNSS_assist" and "acqu_assist"
of "GNSS_assist", both hold "acqu_assist" data. Therefore
"GNSS_ref_measurement_assist" can be omitted when "acqu_assist" is present or vice
versa.
Table 8.55-16: XML DTD for <nms_clock_nav>, <nms_orbit_nav>, <nms_clock_cnav>,
<nms_orbit_cnav>
<!ELEMENT nms_clock_nav (nav_Toc,nav_af2,nav_af1,nav_af0,nav_Tgd)>
<!ELEMENT nav_Toc (#PCDATA)> <!-- 0..37799 -->
<!ELEMENT nav_af2 (#PCDATA)> <!-- -128..127 -->
<!ELEMENT nav_af1 (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_af0 (#PCDATA)> <!-- -2097152..2097151 -->
<!ELEMENT nav_Tgd (#PCDATA)> <!-- -128..127 -->
<!ELEMENT nms_orbit_nav
(nav_URA,nav_FitFlag,nav_Toe,nav_Omega,nav_DeltaN,nav_M0,nav_OmegaA_d,nav_E,nav_I_d,nav_APowerHalf,n
av_I0,nav_OmegaA0,nav_Crs,nav_Cis,nav_Cus,nav_Crc,nav_Cic,nav_Cuc,(nav_CodeOnL2,nav_L2Pflag,nav_sf1_
1,nav_sf1_2,nav_sf1_3,nav_sf1_4,nav_AODA)?)>
<!ELEMENT nav_URA (#PCDATA)> <!-- 0..15 -->
<!ELEMENT nav_FitFlag (#PCDATA)> <!-- 0..1 -->
<!ELEMENT nav_Toe (#PCDATA)> <!-- 0..37799 -->
<!ELEMENT nav_Omega (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT nav_DeltaN (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_M0 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT nav_OmegaA_d (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT nav_E (#PCDATA)> <!-- 0..4294967295 -->
<!ELEMENT nav_I_d (#PCDATA)> <!-- -8192..8191 -->
<!ELEMENT nav_APowerHalf (#PCDATA)> <!-- 0..4294967295 -->
<!ELEMENT nav_I0 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT nav_OmegaA0 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT nav_Crs (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_Cis (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_Cus (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_Crc (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_Cic (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_Cuc (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT nav_CodeOnL2 (#PCDATA)> <!-- 0..3 -->
<!ELEMENT nav_L2Pflag (#PCDATA)> <!-- 0..1 -->
<!ELEMENT nav_sf1_1 (#PCDATA)> <!-- 0..8388607 -->
<!ELEMENT nav_sf1_2 (#PCDATA)> <!-- 0..16777215 -->
<!ELEMENT nav_sf1_3 (#PCDATA)> <!-- 0..16777215 -->
<!ELEMENT nav_sf1_4 (#PCDATA)> <!-- 0..65535 -->
<!ELEMENT nav_AODA (#PCDATA)> <!-- 0..31 -->
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
169
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT nms_clock_cnav
(cnav_Toc,cnav_Top,cnav_URA0,cnav_URA1,cnav_URA2,cnav_Af2,cnav_Af1,cnav_Af0,cnav_Tgd,cnav_ISCl1cp?,c
nav_ISCl1cd?,cnav_ISCl1ca?,cnav_ISCl2c?,cnav_ISCl5i5?,cnav_ISCl5q5?)>
<!ELEMENT cnav_Toc (#PCDATA)> <!-- 0..2015 -->
<!ELEMENT cnav_Top (#PCDATA)> <!-- 0..2015 -->
<!ELEMENT cnav_URA0 (#PCDATA)> <!-- -16..15 -->
<!ELEMENT cnav_URA1 (#PCDATA)> <!-- 0..7 -->
<!ELEMENT cnav_URA2 (#PCDATA)> <!-- 0..7 -->
<!ELEMENT cnav_Af2 (#PCDATA)> <!-- -512..511 -->
<!ELEMENT cnav_Af1 (#PCDATA)> <!-- -524288..524287 -->
<!ELEMENT cnav_Af0 (#PCDATA)> <!-- -33554432..33554431 -->
<!ELEMENT cnav_Tgd (#PCDATA)> <!-- -4096..4095 -->
<!ELEMENT cnav_ISCl1cp (#PCDATA)> <!-- -4096..4095 -->
<!ELEMENT cnav_ISCl1cd (#PCDATA)> <!-- -4096..4095 -->
<!ELEMENT cnav_ISCl1ca (#PCDATA)> <!-- -4096..4095 -->
<!ELEMENT cnav_ISCl2c (#PCDATA)> <!-- -4096..4095 -->
<!ELEMENT cnav_ISCl5i5 (#PCDATA)> <!-- -4096..4095 -->
<!ELEMENT cnav_ISCl5q5 (#PCDATA)> <!-- -4096..4095 -->
<!ELEMENT nms_orbit_cnav
(cnav_Top,cnav_URAindex,cnav_DeltaA,cnav_Adot,cnav_DeltaNo,cnav_DeltaNoDot,cnav_Mo,cnav_E,cnav_Omega
,cnav_OMEGA0,cnav_DeltaOmegaDot,cnav_Io,cnav_IoDot,cnav_Cis,cnav_Cic,cnav_Crs,cnav_Crc,cnav_Cus,cnav
_Cuc)>
<!ELEMENT cnav_URAindex (#PCDATA)> <!-- -16..15 -->
<!ELEMENT cnav_DeltaA (#PCDATA)> <!-- -33554432..33554431 -->
<!ELEMENT cnav_Adot (#PCDATA)> <!-- -16777216..16777215 -->
<!ELEMENT cnav_DeltaNo (#PCDATA)> <!-- -65536..65535 -->
<!ELEMENT cnav_DeltaNoDot (#PCDATA)> <!-- -4194304..4194303 -->
<!ELEMENT cnav_Mo (#PCDATA)> <!-- -4294967296..4294967295 -->
<!ELEMENT cnav_E (#PCDATA)> <!-- 0..8589934591 -->
<!ELEMENT cnav_Omega (#PCDATA)> <!-- -4294967296..4294967295 -->
<!ELEMENT cnav_OMEGA0 (#PCDATA)> <!-- -4294967296..4294967295 -->
<!ELEMENT cnav_DeltaOmegaDot (#PCDATA)> <!-- -65536..65535 -->
<!ELEMENT cnav_Io (#PCDATA)> <!-- -4294967296..4294967295 -->
<!ELEMENT cnav_IoDot (#PCDATA)> <!-- -16384..16383 -->
<!ELEMENT cnav_Cis (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT cnav_Cic (#PCDATA)> <!-- -32768..32767 -->
<!ELEMENT cnav_Crs (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT cnav_Crc (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT cnav_Cus (#PCDATA)> <!-- -1048576..1048575 -->
<!ELEMENT cnav_Cuc (#PCDATA)> <!-- -1048576..1048575 -->
.
Table 8.55-17: XML DTD for <nms_orbit_glonass>, <nms_clock_glonass>
<!ELEMENT nms_orbit_glonass
(glo_En,glo_P1,glo_P2,glo_M,glo_X,glo_X_d,glo_X_dd,glo_Y,glo_Y_d,glo_Y_dd,glo_Z_d,glo_Z_dd)>
<!ELEMENT glo_En (#PCDATA)> <!-- 0..31 -->
<!ELEMENT glo_P1 (#PCDATA)> <!-- hex -->
<!ELEMENT glo_P2 (#PCDATA)> <!-- 0..1 -->
<!ELEMENT glo_M (#PCDATA)> <!-- 0..3 -->
<!ELEMENT glo_X (#PCDATA)> <!-- -67108864..67108863 -->
<!ELEMENT glo_X_d (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT glo_X_dd (#PCDATA)> <!-- -16..15 -->
<!ELEMENT glo_Y (#PCDATA)> <!-- -67108864..67108863 -->
<!ELEMENT glo_Y_d (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT glo_Y_dd (#PCDATA)> <!-- -16..15 -->
<!ELEMENT glo_Z (#PCDATA)> <!-- -67108864..67108863 -->
<!ELEMENT glo_Z_d (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT glo_Z_dd (#PCDATA)> <!-- -16..15 -->
<!ELEMENT nms_clock_glonass (glo_Tau,glo_Gamma,glo_DeltaTau)>
<!ELEMENT glo_Tau (#PCDATA)> <!-- -2097152..2097151 -->
<!ELEMENT glo_Gamma (#PCDATA)> <!-- -1024..1023 -->
<!ELEMENT glo_DeltaTau (#PCDATA)> <!-- -16..15 -->
Table 8.55-18: XML DTD for <nms_clock_sbas>, <nms_orbit_sbas>
<!ELEMENT nms_clock_sbas (sbas_To,sbas_Agfo,sbas_Agf1)> <!-- model 4 -->
<!ELEMENT sbas_To (#PCDATA)>
<!ELEMENT sbas_Agfo (#PCDATA)>
<!ELEMENT sbas_Agf1 (#PCDATA)>
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
170
3GPP TS 27.007 version 13.3.0 Release 13
<!ELEMENT nms_orbit_sbas
(sbas_To,sbas_accuracy,sbas_Xg,sbas_Yg,sbas_Zg,sbas_Xg_d,sbas_Yg_d,sbas_Zg_d,sbas_Xg_dd,sbas_Yg_dd,s
bas_Zg_dd)> <!-- model 4-->
<!ELEMENT sbas_accuracy (#PCDATA)> <!-- hex -->
<!ELEMENT sbas_Xg (#PCDATA)>
<!ELEMENT sbas_Yg (#PCDATA)>
<!ELEMENT sbas_Zg (#PCDATA)>
<!ELEMENT sbas_Xg_d (#PCDATA)>
<!ELEMENT sbas_Yg_d (#PCDATA)>
<!ELEMENT sbas_Zg_d (#PCDATA)>
<!ELEMENT sbas_Xg_dd (#PCDATA)>
<!ELEMENT sbas_Yg_dd (#PCDATA)>
<!ELEMENT sbas_Zg_dd (#PCDATA)>
Table 8.55-19: XML DTD for <GNSS_provided_location_information>
<!ELEMNT GNSS_provided_location_information
(GNSS_meas*|(agnss_list,GNSS_meas_ref_time,locationparameters,earlyFixReport-r12?))>
<!ELEMENT agnss_list (#PCDATA) <!-- Integer corresponds to bit string 1-8 where bit at position
if set, means particular GNSS id is supported bit0-GPS,bit1-sbas,bit2-qzss,bit3-galileo,bit4-
glonass,bit5-bds -->
<!ELEMENT GNSS_meas_ref_time (gnss_TOD_msec,gnss_TOD_frac?,gnss_TOD_unc?)>
<!ATTLIST GNSS_meas_ref_time time_id(SBAS|MGPS|QZSS|Glonass|GPS|BDS) #IMPLIED>
<!ELEMENT gnss_TOD_msec (#PCDATA)> <!-- 0..3599999 -->
<!ELEMENT gnss_TOD_frac (#PCDATA)> <!-- 0..39999 -->
<!ELEMENT gnss_TOD_unc (#PCDATA)> <!-- 0..127 -->
NOTE 15: GNSS_provide_location_information is used for reporting location information for GNSS procedures i.e.
procedures where GNSS_allowed_methods or GNSS_assist is received. This element matches the ASN.1
element GANSSLocationInfo for RRLP procedures; UE positioning measured results information
element for RRC or ASN.1 A-GNSS-ProvideLocationInformation for LPP.
NOTE 15a: Both in "pos_meas" and "pos_meas_req", either MS-Based or MS-Assisted positioning can be
specified requiring either "location_parameters" or "GNSS_meas" elements respectively.
Table 8.55-20: XML DTD for <OTDOA_meas>
<!ELEMENT OTDOA_meas
(system_frame_number,phys_cell_id_ref,cell_global_id_ref?,earfcn_ref?,ref_quality?,neighbour_meas_li
st,earlyFixReport-r12?)>
<!ELEMENT system_frame_number (#PCDATA)>
<!ELEMENT phys_cell_id_ref (#PCDATA)> <!-- 0..503 -->
<!ELEMENT cell_global_id_ref (mcc,mnc,cell_id)>
<!ELEMENT mcc (#PCDATA)>
<!ELEMENT mnc (#PCDATA)>
<!ELEMENT cell_id (#PCDATA)>
<!ELEMENT earfcn_ref (#PCDATA)> <!-- 0..65535 -->
<!ELEMENT ref_quality (OTDOA_meas_quality)>
<!ELEMENT neighbour_meas_list (neighbour_meas_element)+>
<!ELEMENT neighbour_meas_element
(phys_cell_id_neighbour,cell_global_id_neighbour?,earfcn_neighbour?,rstd,rstd_quality)>
<!ELEMENT phys_cell_id_neighbour (#PCDATA)>
<!ELEMENT cell_global_id_neighbour (mcc,mnc,cell_identity)>
<!ELEMENT mcc (#PCDATA)>
<!ELEMENT mnc (#PCDATA)>
<!ELEMENT cell_identity (#PCDATA)>
<!ELEMENT earfcn_neighbour (#PCDATA)> <!-- 0..65535 -->
<!ELEMENT rstd (#PCDATA)> <!-- 0..12711 -->
<!ELEMENT rstd_quality (OTDOA_meas_quality)>
<!ELEMENT OTDOA_meas_quality (err_resolution,err_value,err_num_samples?)>
<!ELEMENT err_resolution (#PCDATA)>
<!ELEMENT err_value (#PCDATA)>
<!ELEMENT err_num_samples (#PCDATA)>
NOTE 16: For the elements and the value ranges of OTDOA measurements refer to 3GPP TS 36.355 [115]
(subclause 6.5.1). The value ranges of relevant parameters are described in the ASN.1 syntax.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
171
3GPP TS 27.007 version 13.3.0 Release 13
Table 8.55-21: XML DTD for <OTDOA_assist_req>
<!ELEMENT OTDOA_assist_req (phys_cell_id)>
<!ELEMENT phys_cell_id (#PCDATA)> <!-- 0..503 -->
Table 8.55-22: XML DTD for <reset_assist_data>
<!ELEMENT reset_assist_data EMPTY> <!-- Reset UE positioning stored AGNSS/OTDOA assistance data -->
NOTE 17: For resetting UE positioning stored AGNSS assistance data refer to 3GPP TS 36.509 [142]
(subclause 6.9).
Table 8.55-23: XML DTD for <OTDOA_ECID_req>
<!ELEMENT OTDOA_ECID_req (abort|request_location_info)>
<!ELEMENT abort EMPTY>
<!ATTLIST abort abort_otdoa_meas_req (true|false) "false"
abort_ecid_meas_req (true|false) "false"> <!-- Session ID will be provided in Transaction ID
under root element <pos> -->
<!ELEMENT request_location_info
(OTDOA_req_loc_info?,ECID_req_loc_info?,(response_time|periodic_reporting|triggered_reporting)?)>
<!-- triggered_reporting for ECID_req_loc_info only -->
<!ATTLIST request_location_info emergency_call_indicator (true|false) "false">
<!ELEMENT OTDOA_req_loc_info EMPTY>
<!ATTLIST OTDOA_req_loc_info assistance_available (true|false) #REQUIRED>
<!ELEMENT ECID_req_loc_info EMPTY>
<!ATTLIST ECID_req_loc_info
rs_rp_req (true|false) "false"
rs_rq_req (true|false) "false"
ue_rx_tx_req (true|false) "false">
<!ELEMENT response_time(time,earlyFixReport-r12?)
<!ELEMENT periodic_reporting (rep_amount,rep_interval)>
<!ELEMENT rep_amount EMPTY>
<!ATTLIST rep_amount literal (ra1|ra2|ra4|ra8|ra16|ra32|ra64|ra-Infinity) #REQUIRED>
<!ELEMENT rep_interval EMPTY>
<!ATTLIST rep_interval literal (ri1|ri2|ri4|ri8|ri16|ri32|ri64)>
<!ELEMENT triggered_reporting (rep_duration)>
<!ATTLIST triggered_reporting cell_change (true|false) #REQUIRED>
<!ELEMENT rep_duration #PCDATA> <!-- 0..255 -->
NOTE 18: "emergency_call_indicator" indicates whether the OTDOA and/or ECID location request is
due to an Emergency Call.
Table 8.55-24: XML DTD for <ECID_meas>
<!ELEMENT ECID_meas (primary_cell_measured_results?,measured_result_list)>
<!ELEMENT primary_cell_measured_results (measured_result_element)>
<!ELEMENT measured_result_element
(phys_cell_id,cell_global_id?,earfcn_eutra,sfn?,rsrp_result?,rsrq_result?,ue_rxtx_time_diff?)>
<!ELEMENT phys_cell_id (#PCDATA)> <!-- 0..503 -->
<!ELEMENT cell_global_id (mcc,mnc,cell_id)>
<!ELEMENT mcc (#PCDATA)>
<!ELEMENT mnc (#PCDATA)>
<!ELEMENT cell_id (#PCDATA)>
<!ELEMENT earfcn_eutra (#PCDATA)> <!-- 0..262143 -->
<!ELEMENT sfn (#PCDATA)>
<!ELEMENT rsrp_result (#PCDATA)> <!-- 0..97 -->
<!ELEMENT rsrq_result (#PCDATA)> <!-- 0..34 -->
<!ELEMENT ue_rxtx_time_diff (#PCDATA)> <!—0..4095 -->
<!ELEMENT measured_result_list (measured_result_element+)> <!-- 1..32 -->
Table 8.55-25: XML DTD for <Strobe>
<!ELEMENT Strobe (#PCDATA)> <!— Triggers the generation of a strobe -->
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
172
3GPP TS 27.007 version 13.3.0 Release 13
Table 8.55-26: XML DTD for <nms_clock_bds>
<!ELEMENT nms_clock_bds (bdsToc-r12,bdsA0-r12,bdsA1-r12,bdsA2-r12,bdsTgd1-r12)>
<!ELEMENT bdsToc-r12 (#PCDATA)> <!-- 0..131071 -->
<!ELEMENT bdsA0-r12 (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT bdsA1-r12 (#PCDATA)> <!-- -2097152..2097151 -->
<!ELEMENT bdsA2-r12 (#PCDATA)> <!-- -1024..1023 -->
<!ELEMENT bdsTgd1-r12 (#PCDATA)> <!-- -512..511-->
Table 8.55-27: XML DTD for <nms_orbit_bds>
<!ELEMENT nms_orbit_bds(bdsURAI-r12,bdsToe-r12,bdsAPowerHalf-r12,bdsE-r12,bdsW-r12,bdsDeltaN-
r12,bdsM0-r12,bdsOmega0-r12,bdsOmegaDot-r12,bdsI0-r12, bdsIDot-r12,bdsCuc-r12,bdsCus-r12,bdsCrc-
r12,bdsCrs-r12,bdsCic-r12,bdsCis-r12)>
<!ELEMENT bdsURAI-r12 (#PCDATA)> <!-- 0..15 -->
<!ELEMENT bdsToe-r12 (#PCDATA)> <!-- 0..131071 -->
<!ELEMENT bdsAPowerHalf-r12 (#PCDATA)> <!-- 0..4294967295 -->
<!ELEMENT bdsE-r12 (#PCDATA)> <!-- 0..4294967295 -->
<!ELEMENT bdsW-r12 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT bdsDeltaN-r12 (#PCDATA)> <!-- (-32768..32767 -->
<!ELEMENT bdsM0-r12 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT bdsOmega0-r12 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT bdsOmegaDot-r12 (#PCDATA)> <!-- -8388608..8388607 -->
<!ELEMENT bdsI0-r12 (#PCDATA)> <!-- -2147483648..2147483647 -->
<!ELEMENT bdsIDot-r12 (#PCDATA)> <!-- -8192..8191 -->
<!ELEMENT bdsCuc-r12 (#PCDATA)> <!-- -131072..131071 -->
<!ELEMENT bdsCus-r12 (#PCDATA)> <!-- -131072..131071 -->
<!ELEMENT bdsCrc-r12 (#PCDATA)> <!-- -131072..131071 -->
<!ELEMENT bdsCrs-r12 (#PCDATA)> <!-- -131072..131071 -->
<!ELEMENT bdsCic-r12 (#PCDATA)> <!-- -131072..131071 -->
<!ELEMENT bdsCis-r12 (#PCDATA)> <!-- -131072..131071 -->
Implementation
Optional.
8.56 Positioning reporting +CPOSR
Table 8.56-1: +CPOSR parameter command syntax
Command
Possible response(s)
+CPOSR=[<mode>]
+CPOSR? +CPOSR: <mode>
+CPOSR=? +CPOSR: (list of supported <mode>s)
Description
Set command enables or disables the sending of unsolicited result codes. The XML-formatted string may be sent as one
or more unsolicited result codes. Each part of the XML-formatted string is sent as one unsolicited result code, prefixed
with +CPOSR.
NOTE: An XML-formatted string intended for +CPOSR can be split e.g. in order to prevent that the string
becomes too long. Where to split an XML-formatted string is implementation specific. The characters
<CR><LF>, <+CPOSR> and space(s) are ignored when re-constructing an XML-formatted string.
Example: +CPOSR: <One line of positioning data sent on XML format>.
Read command returns the current mode.
Test command returns the supported values as a compound value.
Defined values
<mode>: integer type
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
173
3GPP TS 27.007 versio
n 13.3.0 Release 13
0 disables reporting
1 enables reporting
Defined events
<pos_meas>: string type in UTF-8. This parameter provides an XML-formatted string of position measurements
data request as defined in table 8.55-8. This parameter shall not be subject to conventional character conversion
as per +CSCS.
<pos_meas_req>: string type in UTF-8. This parameter provides an XML-formatted string of position
measurements request data as defined in table 8.55-9. This is an alternative to <pos_meas>. This parameter shall
not be subject to conventional character conversion as per +CSCS.
<OTDOA_meas>: string type in UTF-8. This parameter provides an XML-formatted string of OTDOA
measurement data as defined in table 8.55-20. This parameter shall not be subject to conventional character
conversion as per +CSCS.
<ECID_meas>: string type in UTF-8. This parameter provides an XML-formatted string of ECID measurement
data as defined in table 8.55-24. This parameter shall not be subject to conventional character conversion as per
+CSCS.
<OTDOA_assist_req>: string type in UTF-8. This parameter provides an XML-formatted string for requesting
OTDOA assistance data as defined in table 8.55-21. This parameter shall not be subject to conventional
character conversion as per +CSCS.
<capabilities>: string type in UTF-8. This parameter provides an XML-formatted string for providing
capability data as defined in table 8.55-4. This parameter shall not be subject to conventional character
conversion as per +CSCS.
<msg>: string type in UTF-8. This parameter provides an XML-formatted string for communicating simple
messages as defined in table 8.55-13. This parameter shall not be subject to conventional character conversion as
per +CSCS.
<pos_err>: string type in UTF-8. This parameter provides an XML-formatted string of positioning error
parameters as defined in table 8.55-14. This parameter shall not be subject to conventional character conversion
as per +CSCS.
<reset_assist_data>: string type in UTF-8. This parameter provides an XML-formatted string for resetting
GNSS assistance data as defined in table 8.55-22. This parameter shall not be subject to conventional character
conversion as per +CSCS.
Implementation
Optional.
8.57 Mobile terminated location request notification +CMTLR
Table 8.57-1: +CMTLR parameter command syntax
Command
Possible response(s)
+CMTLR=[<subscribe>]
+CMTLR? +CMTLR: <subscribe>
+CMTLR=? +CMTLR: (list of supported <subscribe> values)
Description
Set command enables Mobile Terminated Location Request (MT-LR) notifications to the TE. The parameter
<subscribe> enables or disables notification by an unsolicited result code. It is possible to enable notification of
MT-LR performed over the control plane or over SUPL or both. Relevant location request parameters are provided in
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
174
3GPP TS 27.007 version 13.3.0 Release 13
the unsolicited result code +CMTLR: <handle-id>,<notification-type>,<location-
type>,[<client-external-id>],[<client-name>][,<plane>].
This unsolicited result code is reported upon arrival of a Mobile Terminated Location Request. In order to differentiate
multiple requests, every request is given a different <handle-id>. This ID is used when allowing or denying location
disclosure with +CMTLRA.
Read command returns the current value of <subscribe>.
Test command returns the supported values as a compound value.
Defined values
<subscribe>: integer type. Enables and disables the subscription for MT-LR notifications
0 Disables reporting and positioning.
1 Subscribe for notifications of MT-LR over control plane.
2 Subscribe for notifications of MT-LR over SUPL.
3 Subscribe for notifications of MT-LR over control plane and SUPL.
<handle-id>: integer type. ID associated with each MT-LR used to distinguish specific request in case of
multiple requests. The value range is 0-255.
<notification-type>: integer type. Information about the user's privacy.
0 The subscription may stipulate that positioning the user by a third party is allowed and the network may
choose to inform the user as a matter of courtesy.
1 Locating the user is permitted if the user ignores the notification.
2 Locating the user is forbidden if the user ignores the notification.
<location-type>: integer type. Indicates what type of the location is requested.
0 The current location.
1 The current or last known location.
2 The initial location.
<client-external-id>: string type. Indicates the external client where the location information is sent to (if
required).
<client-name>: string type. Contains the string identifying the external client requesting the user's location
<plane>: integer type. The parameter specifies whether the MT-LR came over control plane or SUPL.
0 Control plane.
1 Secure user plane (SUPL).
Implementation
Optional.
ETSI
ETSI TS 1
27 007 V13.3.0 (2016
-
03)
175
3GPP TS 27.007 version 13.3.0 Release 13
8.58 Mobile terminated location request disclosure allowance
+CMTLRA
Table 8.58-1: +CMTLRA parameter command syntax
Command
Possible response(s)
+CMTLRA=<allow>,<handle_id>
+CMTLRA? +CMTLRA: <allow>,<handle_id>
+CMTLRA=? +CMTLRA: (list of supported <allow> values)
Description
Set command allows or disallows disclosure of the location to the TE as a result of MT-LR by the parameter <allow>.
Read command returns the current values.
Test command returns the supported values.
Defined values
<allow>: integer type. Enables and disables the allowance for location disclosure.
0 Location disclosure allowed.
1 Location disclosure not allowed.
<handle-id>: integer type. ID associated with each MT-LR used to distinguish specific request in case of
multiple requests. The value is given in +CMTLR. The value range is 0-255.
Implementation
Optional.
8.59 Battery capacity +CBCAP
Table 8.59-1: CBCAP parameter command syntax
Command
Possible response(s)
+CBCAP=[<reporting>[,<reporting_
interval>]]
+CBCAP? +CBCAP: <reporting>,<reporting_interval>,<bcl>
+CBCAP=? +CBCAP: (list of supported <reporting>s),(list of supported
<reporting_interval>s)
Description
Set command enables reporting upon change in battery capacity level, with unsolicited result code +CBCAP: <bcl>.
Consecutive reports never show same value of <bcl>.
Read command returns the status of result code presentation and the current battery capacity level.
Test command returns values supported as compound values.
Defined values
<reporting>: integer type. Enables and disables reporting of changes in the battery capacity level.
0 Disable reporting
1 Enable reporting
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
176
3GPP TS 27.007 version 13.3.0 Release 13
<reporting_interval>: integer type. Sets the reporting interval of the battery capacity level (in percentages).
The default value is manufacturer specific.
1...100 Amount that the remaining battery capacity must change before reporting.
<bcl>: integer type. Gives the remaining relative battery capacity level (in percentages).
0 The battery is exhausted or ME does not have a battery connected
1...100 remaining battery capacity level (in percentages). The provided values are dependant on the
parameter <reporting_interval>. A value of 5 for parameter <reporting_interval>, means
that the following values of <bcl> are applicable: 0, 5, 10, 15, … , 90, 95, 100.
NOTE: 100% capacity is always reported, even if <reporting_interval> is set to a value where no integer
multiple equals 100.
Implementation
Optional.
8.60 Battery connection status +CBCON
Table 8.60-1: +CBCON parameter command syntax
Command
Possible response(s)
+CBCON=[<reporting>]
+CBCON? +CBCON: <reporting>,<bcs>
+CBCON=? +CBCON: (list of supported <reporting>s)
Description
Set command enables reporting upon change in battery connection status, with unsolicited result code
+CBCON: <bcs>.
Read command returns the status of result code presentation and the current battery status.
Test command returns values supported as a compound value.
Defined values
<reporting>: integer type. Enables and disables reporting of changes in the battery connection status.
0 disable reporting
1 enable reporting
<bcs>: integer type. Indicates the battery status.
0 ME is powered by the battery
1 ME has a battery connected, but is not powered by it
2 ME does not have a battery connected
3 Recognized power fault, calls inhibited
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
177
3GPP TS 27.007 version 13.3.0 Release 13
8.61 Battery charger status +CBCHG
Table 8.61-1: +CBCHG parameter command syntax
Command
Possible response(s)
+CBCHG=[<reporting>]
+CBCHG? +CBCHG: <reporting>,<chg_status>
+CBCHG=? +CBCHG: (list of supported <reporting>s)
Description
Set command enables reporting upon change in battery charger status, with unsolicited result code
+CBCHG: <chg_status>.
Read command returns the status of result code presentation and the current battery charger status.
Test command returns values supported as a compound value.
Defined values
<reporting>: integer type. Enables and disables reporting of changes in the battery charger status.
0 disable reporting
1 enable reporting
<chg_status>: integer type. Indicates type of battery charger status.
0 no charger connected
1 charger connected, normal type charger
2 charger connected, USB type charger
Implementation
Optional.
8.62 Printing IP address format +CGPIAF
Table 8.62-1: +CGPIAF parameter command syntax
Command
Possible response(s)
+CGPIAF=[<IPv6_AddressFormat>[,<
IPv6_SubnetNotation>[,<IPv6_Lead
ingZeros>[,<IPv6_CompressZeros>]
]]]
+CGPIAF? +CGPIAF: <IPv6_AddressFormat>,<IPv6_SubnetNotation
>,<IPv6_LeadingZeros>,<IPv6_CompressZeros>
+CGPIAF=? +CGPIAF: (list of supported <IPv6_AddressFormat>s),(list of
supported <IPv6_SubnetNotation>s),(list of supported
<IPv6_LeadingZeros>s),(list of supported
<IPv6_CompressZeros>s)
Description
Set command decides what format to print IPV6 address parameters of other AT commands. See RFC 4291 [88] for
details of the IPv6 address format.
The +CGPIAF parameters <IPv6_AddressFormat>, <IPv6_SubnetNotation>, <IPv6_LeadingZeros>
and <IPv6_CompressedZeros> affect the following commands and parameters:
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
178
3GPP TS 27.007 version 13.3.0
Release 13
a) in +CGTFT and +CGTFTRDP, the <remote address and subnet mask>;
b) in +CGDCONT, the <PDP_addr>;
c) in +CGPADDR, the <PDP_addr_1> and <PDP_addr_2>;
d) in +CGCONTRDP, the <local address and subnet mask>, <DNS_prim_addr>,
<DNS_sec_addr>, <P_CSCF_prim_addr> and <P_CSCF_sec_addr>; and
e) in +CRC, the <PDP_addr> of unsolicited result code GPRS <PDP_type>, <PDP_addr>[,
[<L2P>][,<APN>]].
Read command returns the current command parameter settings.
Test command returns values supported as compound values.
Defined values
<IPv6_AddressFormat>: integer type, decides the IPv6 address format. Relevant for all AT command
parameters that can hold an IPv6 address.
0 Use IPv4-like dot-notation. IP address, and subnetwork mask if applicable, are dot-separated.
Example: For <remote address and subnet mask>:
"32.1.13.184.0.0.205.48.0.0.0.0.0.0.0.0.255.255.255.255.255.255.255.240.0.0.0.0.0.0.0.0"
For other IP address parameters:
"32.1.13.184.0.0.205.48.0.0.0.0.0.0.0.0"
1 Use IPv6-like colon-notation. IP address, and subnetwork mask if applicable and when given explicitly, are
separated by a space.
Example: For <remote address and subnet mask>:
"2001:0DB8:0000:CD30:0000:0000:0000:0000 FFFF:FFFF:FFFF:FFF0:0000:0000:0000:0000"
For other IP address parameters:
"2001:0DB8:0000:CD30:0000:0000:0000:0000"
<IPv6_SubnetNotation>: integer type, decides the subnet-notation for <remote address and subnet
mask. Setting does not apply if <IPv6_AddressFormat> = 0.
0 Both IP Address and subnet mask are stated explicitly, separated by a space.
Example: "2001:0DB8:0000:CD30:0000:0000:0000:0000 FFFF:FFFF:FFFF:FFF0:0000:0000:0000:0000"
1 The printout format is applying / (forward slash) subnet-prefix Classless Inter-Domain Routing (CIDR)
notation.
Example: "2001:0DB8:0000:CD30:0000:0000:0000:0000/60"
<IPv6_LeadingZeros>: integer type, decides whether leading zeros are omitted or not. Setting does not
apply if <IPv6_AddressFormat> = 0.
0 Leading zeros are omitted.
Example: "2001:DB8:0:CD30:0:0:0:0"
1 Leading zeros are included.
Example: "2001:0DB8:0000:CD30:0000:0000:0000:0000"
<IPv6_CompressZeros>: integer type, decides whether 1-n instances of 16-bit zero-values are replaced by only
'::'. This applies only once. Setting does not apply if <IPv6_AddressFormat> = 0.
0 No zero compression.
Example: "2001:DB8:0:CD30:0:0:0:0"
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
179
3GPP TS 27.007 version 13.3.0 Release 13
1 Use zero compression.
Example: "2001:DB8:0:CD30::"
Implementation
Optional.
8.63 IMS single radio voice call continuity +CISRVCC
Table 8.63-1: +CISRVCC parameter command syntax
Command
Possible response(s)
+CISRVCC=[<uesrvcc>] +CME ERROR: <err>
+CISRVCC? +CISRVCC: <uesrvcc>
+CISRVCC=? +CISRVCC: (list of supported <uesrvcc>s)
Description
SRVCC provides the ability to have a seamless handover of a voice call between the PS domain and the CS domain for
calls that are anchored in IMS, when the UE is capable of transmitting/receiving on only one of those access networks
(PS or CS) at a given time, see 3GPP TS 23.221 [90] subclause 7.2a, annex A.1 and annex A.2
Set command informs MT about the SRVCC Support. MT normally updates the network when changing this parameter.
Refer subclause 9.2 for possible <err> values.
Read command returns the status of the MT stored SRVCC Support.
Test command returns supported values as a compound value.
Defined values
<uesrvcc>: integer type. SRVCC support status
0 The UE does not have SRVCC support
1 The UE has SRVCC support
Implementation
Optional.
8.64 IMS network reporting +CIREP
Table 8.64-1: +CIREP parameter command syntax
Command
Possible response(s)
+CIREP=[<reporting>]
+CIREP? +CIREP: <reporting>,<nwimsvops>
+CIREP=? +CIREP: (list of supported <reporting>s)
Description
Set command enables or disables reporting of PS to CS Single Radio Voice Call Continuity (SRVCC), PS to CS Single
Radio Video Call Continuity (vSRVCC) handover information and CS to PS Single Radio Voice Call Continuity (see
3GPP TS 24.237 [91]) and of IMS Voice Over PS sessions (IMSVOPS) indicator information, by the following
unsolicited result codes:
+CIREPI: <nwimsvops> IMS Voice Over PS sessions (IMSVOPS) supported indication from the network.
ETSI
ETSI TS 127 007 V
13.3.0 (2016
-
03)
180
3GPP TS 27.007 version 13.3.0 Release 13
+CIREPH: <srvcch> Provides PS to CS SRVCC, PS to CS vSRVCC and CS to PS SRVCC handover
information.
Read command returns the status of result code presentation and the IMSVOPS supported indication.
Test command returns supported values as a compound value.
Defined values
<reporting>: integer type. Enables or disables reporting of changes in the IMSVOPS supported indication
received from the network and reporting of PS to CS SRVCC, PS to CS vSRVCC and CS to PS SRVCC
handover information.
0 Disable reporting
1 Enable reporting
<nwimsvops>: integer type. Gives the last IMS Voice Over PS sessions (IMSVOPS) supported indication
received from network.
0 IMSVOPS support indication is not received from network, or is negative.
1 IMSVOPS support indication as received from network is positive.
<srvcch>: integer type. PS to CS SRVCC, PS to CS vSRVCC and CS to PS SRVCC handover information.
0 PS to CS SRVCC handover has started in the CS domain ("Handover Command" indicating PS to CS
SRVCC received).
1 PS to CS SRVCC handover successful ("Handover Complete" sent).
2 PS to CS SRVCC or PS to CS vSRVCC handover cancelled ("Handover Failure" sent).
3 PS to CS SRVCC or PS to CS vSRVCC handover, general non-specific failure.
4 PS to CS vSRVCC handover has started in the CS domain ("Handover Command" indicating vSRVCC
received).
5 PS to CS vSRVCC handover successful ("Handover Complete" sent).
6 CS to PS SRVCC handover has started in the PS domain ("Handover Command" indicating CS to PS
SRVCC received).
7 CS to PS SRVCC handover cancelled ("Handover Failure" sent).
8 CS to PS SRVCC handover, general non-specific failure.
9 CS to PS SRVCC handover successful ("Handover Complete" sent).
NOTE 1: Value 3 and 8, general non-specific failure, might be used e.g. in the case of handover cancellation as
specified in 3GPP TS 24.301 [83] subclause 6.6.2.
NOTE 2: The naming of SRVCC and vSRVCC handover information values is different from the naming of
corresponding NAS session management notifications.
Implementation
Optional.
8.65 Remaining PIN retries +CPINR
Table 8.65-1: +CPINR action command syntax
Command
Possible response(s)
+CPINR[=<sel_code>] +CME ERROR: <err>
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
181
3GPP TS 27.007 version 13.3.0 Release 13
+CPINR=?
Description
Execution command cause the MT to return the number of remaining PIN retries for the MT passwords with
intermediate result code +CPINR: <code>,<retries>[,<default_retries>] for standard PINs and
+CPINRE: <ext_code>,<retries>[,<default_retries>] for manufacturer specific PINs. One line with
one intermediate result code is returned for every <code> or <ext_code> selected by <sel_code>.
When execution command is issued without the optional parameter <sel_code>, intermediate result codes are
returned for all <code>s and <ext_code>s.
In the intermediate result codes, the parameter <default_retries> is an optional (manufacturer specific)
parameter, per <code> and <ext_code>.
Refer subclause 9.2 for possible <err> values.
Defined values
<retries>: integer type. Number of remaining retries per PIN.
<default_retries>: integer type. Number of default/initial retries per PIN.
<code>: Type of PIN. All values listed under the description of the AT+CPIN command, <code> parameter,
except 'READY'.
<ext_code>: Extended, manufacturer specific codes.
<sel_code>: String type. Same values as for the <code> and <ext_code> parameters. These values are
strings and shall be indicated within double quotes. It is optional to support wildcard match by '*', meaning
match any (sub-)string.
Example: AT+CPINR="SIM*" will return the lines:
+CPINR: SIM PIN,<retries>,<default_retries>
+CPINR: SIM PUK,<retries>,<default_retries>
+CPINR: SIM PIN2,<retries>,<default_retries>
+CPINR: SIM PUK2,<retries>,<default_retries>
Example: AT+CPINR="*SIM*" will additionally return the lines:
+CPINR: PH-SIM PIN,<retries>,<default_retries>
+CPINR: PH-FSIM PIN,<retries>,<default_retries>
+CPINR: PH-FSIM PUK,<retries>,<default_retries>
Implementation
Optional.
8.66 Set card slot +CSUS
Table 8.66-1: +CSUS parameter command syntax
Command
Possible response(s)
+CSUS=[<card slot>] +CME ERROR: <err>
+CSUS? +CSUS: <card slot>
+CSUS=? +CSUS: (number of supported <card slot>s)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
182
3GPP TS 27.007 version 13.3.0 Release 13
Description
When a MT is equipped with multiple card slots, the set command directs the MT to select the SIM/UICC card installed
in the indicated card slot in all future actions that require the use of SIM/UICC.
If this command is issued when a SIM/UICC is active, +CME ERROR is returned. Refer to subclause 9.2 for possible
<err> values.
Read command returns the currently selected card slot.
Test command returns the number of card slots in the MT as a compound value.
The numbering of card slots is implementation dependent.
Defined values
<card slot>: integer type.
0 the SIM/UICC card installed in card slot 0
1 the SIM/UICC card installed in card slot 1
2 the SIM/UICC card installed in card slot 2
3 the SIM/UICC card installed in card slot 3
Implementation
Optional.
8.67 Emergency numbers +CEN
Table 8.67-1: +CEN parameter command syntax
Command
Possible response(s)
+CEN=[<reporting>]
+CEN? +CEN1: <reporting>[,<mcc>,<mnc>]
<CR><LF>[+CEN2: <cat>,<number>
[<CR><LF>+CEN2: <cat>,<number>
[...]]]
+CEN=? +CEN: (list of supported <reporting>s)
Description
This command allows for reading and dynamical reporting of emergency numbers as received from the network. The
emergency numbers are not necessarily received for the same <mcc> and <mnc> as currently registered to.
Read command returns one line of intermediate result code +CEN1: <reporting>,<mcc> with the current
<reporting> setting and the Mobile Country Code <mcc>. Then follows zero or more occurrences of the
emergency numbers with intermediate result code +CEN2: <cat>,<number>.
Set command enables reporting of new emergency numbers received from the network with unsolicited result codes
equal to the intermediate result codes of the read form of the command.
Test command returns values supported as a compound value.
Defined values
<reporting>: integer type. Enables and disables reporting of new emergency numbers received from the
network.
0 Disable reporting
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
183
3GPP TS 27.007 version 13.3.0 Release
13
1 Enable reporting
<mcc>: integer type. A three-digit value indicating mobile country code as defined in
ITU-T Recommendation E.212 [10] Annex A.
<mnc>: integer type. A three-digit value indicating the mobile network code.
<cat>: integer type. A bitmap indicating the Emergency Service Category Value according to 3GPP TS 24.008 [8]
table 10.5.135d.
<number>: String type. Representing an emergency number from the list defined in
3GPP TS 24.008 [8]subclause 10.5.3.13. The <number> is encoded with one digit per character and is
applicable to the country indicated by <mcc>.
Implementation
Optional.
8.68 Availability for voice calls with IMS +CAVIMS
Table 8.68-1: +CAVIMS parameter command syntax
Command
Possible response(s)
+CAVIMS=[<state>]
+CAVIMS? +CAVIMS: <state>
+CAVIMS=? +CAVIMS: (list of supported <state>s)
Description
Set command informs the MT whether the UE is currently available for voice calls with the IMS (see
3GPP TS 24.229 [89]). The information can be used by the MT to determine "IMS voice not available" as defined in
3GPP TS 24.301 [83], and for mobility management for IMS voice termination, see 3GPP TS 24.008 [20].
Read command returns the UEs IMS voice call availability status stored in the MT.
Test command returns supported values as a compound value.
Defined values
<state>: integer type. The UEs IMS voice call availability status.
0 Voice calls with the IMS are not available
1 Voice calls with the IMS are available
Implementation
Optional.
8.69 Extended signal quality +CESQ
Table 8.69-1: +CESQ action command syntax
Command
Possible response(s)
+CESQ +CESQ: <rxlev>,<ber>,<rscp>,<ecno>,<rsrq>,<rsrp>
+CME ERROR: <err>
+CESQ=? +CESQ: (list of supported <rxlev>s),(list of supported
<ber>s),(list of supported <rscp>s),(list of supported
<ecno>s),(list of supported <rsrq>s),(list of supported <rsrp>s)
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
184
3GPP TS 27.007 version 13.3.0 Release 13
Description
Execution command returns received signal quality parameters. If the current serving cell is not a GERAN cell,
<rxlev> and <ber> are set to value 99. If the current serving cell is not a UTRA FDD or UTRA TDD cell, <rscp>
is set to 255. If the current serving cell is not a UTRA FDD cell, <ecno> is set to 255. If the current serving cell is not
an E-UTRA cell, <rsrq> and <rsrp> are set to 255.
Refer subclause 9.2 for possible <err> values.
Test command returns values supported as compound values.
Defined values
<rxlev>: integer type, received signal strength level (see 3GPP TS 45.008 [20] subclause 8.1.4).
0 rssi < -110 dBm
1 -110 dBm ≤ rssi < -109 dBm
2 -109 dBm ≤ rssi < -108 dBm
: : : :
61 -50 dBm ≤ rssi < -49 dBm
62 -49 dBm ≤ rssi < -48 dBm
63 -48 dBm ≤ rssi
99 not known or not detectable
<ber>: integer type; channel bit error rate (in percent)
0...7 as RXQUAL values in the table in 3GPP TS 45.008 [20] subclause 8.2.4
99 not known or not detectable
<rscp>: integer type, received signal code power (see 3GPP TS 25.133 [95] subclause 9.1.1.3 and
3GPP TS 25.123 [96] subclause 9.1.1.1.3).
0 rscp < -120 dBm
1 -120 dBm ≤ rscp < -119 dBm
2 -119 dBm ≤ rscp < -118 dBm
: : : :
94 -27 dBm ≤ rscp < -26 dBm
95 -26 dBm ≤ rscp < -25 dBm
96 - 25 dBm ≤ rscp
255 not known or not detectable
<ecno>: integer type, ratio of the received energy per PN chip to the total received power spectral density (see
3GPP TS 25.133 [95] subclause).
0 Ec/Io < -24 dB
1 -24 dB ≤ Ec/Io < -23.5 dB
2 -23.5 dB ≤ Ec/Io < -23 dB
: : : :
ETSI
ETSI TS 127 007 V13.3.0 (
2016
-
03)
185
3GPP TS 27.007 version 13.3.0 Release 13
47 -1 dB ≤ Ec/Io < -0.5 dB
48 -0.5 dB ≤ Ec/Io < 0 dB
49 0 dB ≤ Ec/Io
255 not known or not detectable
<rsrq>: integer type, reference signal received quality (see 3GPP TS 36.133 [96] subclause 9.1.7).
0 rsrq < -19.5 dB
1 -19.5 dB ≤ rsrq < -19 dB
2 -19 dB ≤ rsrq < -18.5 dB
: : : :
32 -4 dB ≤ rsrq < -3.5 dB
33 -3.5 dB ≤ rsrq < -3 dB
34 -3 dB ≤ rsrq
255 not known or not detectable
<rsrp>: integer type, reference signal received power (see 3GPP TS 36.133 [96] subclause 9.1.4).
0 rsrp < -140 dBm
1 -140 dBm ≤ rsrp < -139 dBm
2 -139 dBm ≤ rsrp < -138 dBm
: : : :
95 -46 dBm ≤ rsrp < -45 dBm
96 -45 dBm ≤ rsrp < -44 dBm
97 -44 dBm ≤ rsrp
255 not known or not detectable
Implementation
Optional.
8.70 Primary notification event reporting +CPNER
Table 8.70-1: +CPNER parameter command syntax
Command
Possible response(s)
+CPNER=[<reporting>] +CME ERROR: <err>
+CPNER? +CPNER:<reporting>
+CME ERROR: <err>
+CPNER=?
+CPNER: (list of supported <reporting>s)
+CME ERROR: <err>
Description
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
186
3GPP TS 27.007 version 13.3.0 Release 13
Set command enables and disables reporting of primary notification events when received from the network with
unsolicited result code +CPNERU: <message_identifier>,<serial_number>,<warning_type>.
Primary notification events are used for public warning systems like ETWS (Earthquake and Tsunami Warning
Systems).
When <reporting>=1, duplicate primary notifications will be discarded by the UE.
NOTE 1: The notification is considered a duplicate of the previous if it has equal <message_identifier> and
<serial_number> and arrives from the same PLMN. A primary notification message stored to detect
duplication is cleared automatically after three hours of not receiving any message.
Read command returns the current settings.
Test command returns supported values as a compound value.
Refer subclause 9.2 for possible <err> values.
Defined values
<reporting>: integer type, controlling reporting of primary notification events
0 Disable primary notification events.
1 Enable reporting of primary notification events without security information, unsolicited result code
+CPNERU: <message_identifier>,<serial_number>,<warning_type>.
NOTE 2: Provision of information for the digital signature authentication is referred to as "reporting of primary
notification events with security information" in 3GPP TS 25.331 [74], 3GPP TS 36.331 [86]) and
3GPP TS 23.041 [100]. This functionality is not fully implemented in this release, hence is not supported.
<message_identifier>: string type in hexadecimal character format. The parameter contains the message
identifier (2 bytes) of the primary notification. For UTRAN see 3GPP TS 25.331 [74] subclause 10.3.8.4.ea, for
GERAN see 3GPP TS 23.041 [100] subclause 9.4.1.3.2, and for E-UTRAN see 3GPP TS 36.331 [86]
subclause 6.3.1 SystemInformationBlockType10).
<serial_number>: string type in hexadecimal character format. The parameter contains the serial number (2
bytes) of the primary notification. For UTRAN see 3GPP TS 25.331 [74] subclause 10.3.8.4.ea, for GERAN see
3GPP TS 23.041 [100] subclause 9.4.1.3.2, and for E-UTRAN see 3GPP TS 36.331 [86] subclause 6.3.1
SystemInformationBlockType10).
<warning_type>: string type in hexadecimal character format. The parameter contains the warning type (2
bytes) of the primary notification. For UTRAN see 3GPP TS 25.331 [74] subclause 10.3.8.4.ea, for GERAN see
3GPP TS 23.041 [100] subclause 9.4.1.3.2, and for E-UTRAN see 3GPP TS 36.331 [86] subclause 6.3.1
SystemInformationBlockType10).
Implementation
Optional.
8.71 IMS registration information +CIREG
Table 8.71-1: +CIREG parameter command syntax
Command
Possible response(s)
+CIREG=[<n>] +CME ERROR: <err>
+CIREG? +CIREG: <n>,<reg_info>[,<ext_info>]
+CIREG=? +CIREG: (list of supported <n>s)
Description
The set command controls the presentation of an unsolicited result code +CIREGU: <reg_info>[,<ext_info>]
when there is a change in the MT's IMS registration information. Refer subclause 9.2 for possible <err> values.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
187
3GPP TS 27.007 version 13.3.0 Release 13
The read command returns <n>, that shows whether reporting is enabled or disabled, <reg_info> that shows
whether one or more of the public user identities are registered and optionally <ext_info>, that shows the status of
the MT's IMS capabilities. For <ext_info>, all relevant values are always summarized and reported as a complete
set of IMS capabilites in the unsolicited result code.
The test command returns the supported values for <n> as a compound value.
Defined values
<n>: integer type. Enables or disables reporting of changes in the MT's IMS registration information.
0 disable reporting.
1 enable reporting (parameter <reg_info>).
2 enable extended reporting (parameters <reg_info> and <ext_info>).
<reg_info>: integer type. Indicates the IMS registration status. The UE is seen as registered as long as one or
more of its public user identities are registered with any of its contact addresses, see 3GPP TS 24.229 [89].
0 not registered.
1 registered.
<ext_info>: numeric value in hexadecimal format. The value range is from 1 to FFFFFFFF. It is a sum of
hexadecimal values, each representing a particular IMS capability of the MT. The MT can have IMS capabilites
not covered by the below list. This parameter is not present if the IMS registration status is "not registered".
1 RTP-based transfer of voice according to MMTEL, see 3GPP TS 24.173 [87]. This functionality can not be
indicated if the UE is not available for voice over PS, see 3GPP TS 24.229 [89].
2 RTP-based transfer of text according to MMTEL, see 3GPP TS 24.173 [87].
4 SMS using IMS functionality, see 3GPP TS 24.341 [101].
8 RTP-based transfer of video according to MMTEL, see 3GPP TS 24.173 [87].
The hexadecimal values 10, 20, 40 … 80000 are reserved by the present document.
Example: The parameter <ext_info>=5 means that both RTP-based transfer of voice according to MMTEL
and SMS using IMS functionality can be used.
Implementation
Optional.
8.72 Availability for SMS using IMS +CASIMS
Table 8.72-1: +CASIMS parameter command syntax
Command
Possible response(s)
+CASIMS=[<state>]
+CASIMS? +CASIMS: <state>
+CASIMS=? +CASIMS: (list of supported <state>s)
Description
Set command informs the MT whether the UE is currently available for SMS using IMS (see 3GPP TS 24.229 [89]).
The information can be used by the MT to determine the need to remain attached for non-EPS services, as defined in
3GPP TS 24.301 [83].
Read command returns the UE's SMS using IMS availability status, as stored in the MT.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
188
3GPP TS 27.007 version 13.3.0 Release 13
Test command returns supported values as a compound value.
Defined values
<state>: integer type. The UE's SMS using IMS availability status.
0 SMS using IMS is not available
1 SMS using IMS is available
Implementation
Optional.
8.73 Monitor of current calls +CMCCS
Table 8.73-1: +CMCCS parameter command syntax
Command
Possible response(s)
+CMCCS=[<n>]
when <n>=1 and command successful:
+CMCCS: (list of supported <x>s)
+CMCCS? +CMCCS: <n>
+CMCCS=? +CMCCS: (list of supported <n>s)
Description
This command activates or deactivates a call monitoring function in the ME. When this function is activated in the ME,
the ME informs about events for calls with unsolicited result codes.
The purpose of the call monitoring function is to:
1) gather relevant information for the detected calls in a TE; and
2) make it possible for the TE to display call state information for ongoing calls.
The unsolicited result code+CMCCSI is used for basic call information.
+CMCCSI: <ccidx>,<dir>,<neg_status_present>,<neg_status>,<SDP_md>,<cs_mode>,<ccs
tatus>,<mpty>,<numbertype>,<ton>,<number>,<exittype>,<exitcause>
The unsolicited result code +CMCCSI is provided when <n>=2. For an originating call, the parameters
<numbertype>, <ton> and <number> in +CMCCSI provide the number (line identity) information which has been
dialled with +CDU or ATD. For a terminating call, the parameters <numbertype>, <ton> and <number> in
+CMCCSI provide the number (line identity) information of the calling user.
The unsolicited result codes +CMCCSS<x> / +CMCCSSEND are used for supplementary service related information.
+CMCCSS1: <ccidx>,<dir>,<service>
[+CMCCSS2: <numbertype>,<ton>,<number>]
[+CMCCSS3: <CLI_validity>]
[+CMCCSS4: <name>]
[+CMCCSS5: <subaddr>,<satype>]
[+CMCCSS6: <priority>]
[+CMCCSS7: <CUG_index>]
+CMCCSSEND
The unsolicited result codes +CMCCSS<x> / +CMCCSSEND are used for supplementary service related information and
are reported when <n>=3. For every supplementary service related event, the unsolicited result codes +CMCCSS<x>
shall be given in consecutive order, and the sequence of unsolicited result codes shall be terminated by +CMCCSSEND.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
189
3GPP TS 27.007 version 13.3.0 Release 13
It is manufacturer specific when and if this additional service reporting will be issued. Whenever a service event is to be
reported using these unsolicited result codes, the codes +CMCCSS1 and +CMCCSSEND are mandatory. +CMCCSS1
contains essential information that is always needed (for example <ccidx>) and +CMCCSSEND indicates the end of
this particular set of unsolicited result codes. The other unsolicited result codes(+CMCCSS2 to +CMCCSSn) are
optional, intended to provide information related to a given service. E.g. for the supplementary service CNAP, the
unsolicited result code +CMCCSS4 (containing <name>) may be issued. It is implementation specific which of the
unsolicited result codes +CMCCSS<x> / +CMCCSSEND that are supported and provided to the TE. The unsolicited
result codes should be provided to the TE as soon as the information is available in the ME. The parameters
<numbertype>, <ton> and <number> in +CMCCSS2 are, if applicable, normally the line identity information that
is related to the parameter <service>.
NOTE 1: For situations where ringing is applicable, the unsolicited result codes +CMCCSS<x> / +CMCCSSEND are
typically returned after the first RING (or +CRING: <type>; refer subclause "Cellular result codes
+CRC") result code sent from TA to TE.
A subset of the information provided by the call monitoring function can be provided by the command +CLCCS.
When the unsolicited result code +CMCCSI report that the <ccstatus>=1 (Idle), the call identification number is
reset and the call identification number <ccidx> can be used by new calls. The logic for reuse of the parameter
<ccidx> is implementation specific.
Read command returns the current value of <n>.
Test command returns the values supported as a compound value.
Defined values
<n>: integer type
0 The call monitoring function is disabled
1 List the unsolicited result codes +CMCCSS<x> that are supported by the TE. The supported values for <x>
are reported as a compound value, e.g. a TE supporting +CMCCSS1, +CMCCSS2 and +CMCCSS5 will report
+CMCCS: (1,2,5) or +CMCCS: (1-2,5)
2 The call monitoring function is enabled for basic call information (unsolicited result code +CMCCSI)
3 The call monitoring function is enabled for basic call information and supplementary service information
(unsolicited result codes +CMCCSI and +CMCCSS<x> / +CMCCSSEND)
<x>: integer type. <x> is the suffix in the unsolicited result codes +CMCCSS<x>.
<ccidx>: integer type. Call identification number as described in 3GPP TS 22.030 [19] subclause 6.5.5.1. This
number can be used in +CHLD command operations. Value range is from 1 to N. N, the maximum number of
simultaneous call control processes is implementation specific. The call identification number must not be reused
until the unsolicited result code +CMCCSI has indicated that the <ccstatus>=1 (Idle).
<dir>: integer type
0 mobile originated (MO) call
1 mobile terminated (MT) call
<neg_status_present>: integer type. Indicates whether parameter <neg_status> has any valid
information
0 No valid information in parameter <neg_status>. Parameter <neg_status> is set to zero.
1 Valid information in parameter <neg_status>.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
190
3GPP TS 27.007 version 13.3.0 Release 13
<neg_status>: integer type as defined in the +CCMMD command
0 The parameter <neg_status> has no valid content. Parameter <SDP_md> is set to an empty string ("").
1 The <SDP_md> parameter describes the active media in the call.
2 The <SDP_md> parameter describes a proposed but not yet active new set of media for the call.
3 A proposed new set of media for the call was accepted by the remote party. The <SDP_md> parameter
describes the active media in the call (if any).
4 A proposed new set of media for the call was rejected by the remote party. The <SDP_md> parameter
describes the active media in the call (if any).
<SDP_md>: string type represented with IRA characters. Media description as per the +CDEFMP command. This
parameter shall not be subject to conventional character conversion as per +CSCS. This parameter will be an
empty string ("") if the call has no multimedia content.
<cs_mode>:integer type (bearer/teleservice). Applicable to CS calls only.
0 no relevant information about bearer/teleservice
1 voice
2 data
3 fax
4 voice followed by data, voice mode
5 alternating voice/data, voice mode
6 alternating voice/fax, voice mode
7 voice followed by data, data mode
8 alternating voice/data, data mode
9 alternating voice/fax, fax mode
255 unknown
<ccstatus>: integer type Indicating the state of the call.
1 Idle
2 Calling (MO); the call setup has been started
3 Connecting (MO); the call is in progress
4 Alerting (MO): an alert indication has been received
5 Alerting (MT); an alert indication has been sent
6 Active; the connection is established
7 Released; an outgoing (MO) call is released.
8 Released; an incoming (MT) call is released
9 User Busy
10 User Determined User Busy
11 Call Waiting (MO)
12 Call Waiting (MT)
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
191
3GPP TS 27.007 version 13.3.0 Release 13
13 Call Hold (MO)
14 Call Hold (MT)
<mpty>: integer type
0 call is not one of multiparty (conference) call parties
1 call is one of multiparty (conference) call parties
<numbertype>: integer type. Indicating type of information in parameter <number>.
0 No valid information in parameter <number>. <number> shall then be set to empty string ("").
1 Number in <number> according to URI including the prefix specifying the URI type (see command +CDU).
Parameter <ton> has no relevant information and is set to zero.
2 Number in <number> according to one of the formats supported by 3GPP TS 24.008 [8]
subclause 10.5.4.7)
<ton>: type of number in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7). The parameter is also set
to zero when it has no meaningful content, e.g. when <numbertype>=1.
<number>: string type phone number in format specified by <numbertype>. The used character set should be
the one selected with Select TE Character Set +CSCS. When no number is available, <number> shall be set to
empty string ("").
<exittype>: integer type. Indicating type of information in parameter <exitcause>.
0 No valid information in parameter <exitcause>
1 Cause in <exitcause> according to 3GPP TS 24.008 [8], Annex H
2 Cause in <exitcause> according to 3GPP TS 24.229 [89], Annex A.2.1.4.1
<exitcause>: integer type. Additional information provided if relevant. If there is no relevant cause to report, or
if <exittype>=0 the exitcause is set to 0 (<exitcause>=0).
<service>: integer type. Indication of the indicated (supplementary) service. It is vendor specific which of the
services that are provided. The related unsolicited result codes +CMCCSS<x> are provided as applicable for a
given <service>, e.g. the +CMCCSS5: <subaddr>,<satype> can be omitted when it is not relevant for
the service, but can also be omitted if this information is not provided for a relevant service or if a vendor does
not support parameters <subaddr> and <satype>.
0 No service
1 Originating identification presentation – CLIP / OIP, refer 3GPP TS 22.081 [3] and 3GPP TS 24.607 [119]
CLIP / OIP specific information can be provided in:
+CMCCSI (in parameters <numbertype>, <ton> and <number>)
Additional CLIP / OIP specific information can be provided in:
+CMCCSS1 (in parameter <service>)
+CMCCSS3 (in parameter <CLI_validity>, typically used when no <number> is available)
+CMCCSS5 (in parameters <subaddr> and <satype>, when applicable)
2 Originating identification restriction – CLIR / OIR, refer 3GPP TS 22.081 [3] and 3GPP TS 24.607 [119]
3 Terminating identification presentation – COLP / TIP, refer 3GPP TS 22.081 [3] and 3GPP TS 24.608 [120]
COLP / TIP specific information can be provided in:
+CMCCSI (in parameters <numbertype>, <ton> and <number>)
Additional COLP / TIP specific information can be provided in:
+CMCCSS1 (in parameter <service>)
+CMCCSS5 (in parameters <subaddr> and <satype>, when applicable)
4 Terminating identification restriction – COLR / TIR, refer 3GPP TS 22.081 [3] and 3GPP TS 24.608 [120]
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
192
3GPP TS 27.007 version 13.3.0 Release 13
5 Called line presentation – CDIP
Additional CDIP specific information can be provided in:
+CMCCSS1 (in parameter <service>)
+CMCCSS2 (in parameters <numbertype>, <ton> and <number>)
+CMCCSS5 (in parameters <subaddr> and <satype>, when applicable)
NOTE 2: The command +CDIP does not explicitly specify what "multiple called numbers" it is intended to
support. +CMCCS can therefore not be more specific. The CDIP service in +CMCCS is therefore intended
for manufacturers who already have chosen a manufacturer specific way to support +CDIP and needs to
extend or replace +CDIP with support for SIP URIs. For manufacturers who do not already support the
command +CDIP, the useage of the CDIP service in +CMCCS is deprecated.
6 Calling name presentation – CNAP, refer 3GPP TS 22.096 [93]
Additional CNAP specific information can be provided in:
+CMCCSS1 (in parameter <service>)
+CMCCSS4 (in parameter <name>)
7 Communication deflection – CD, refer 3GPP TS 22.072 [31] and 3GPP TS 24.604 [132]
8 Communication forwarding unconditional – CFU, refer 3GPP TS 22.082 [4] and 3GPP TS 24.604 [132]
9 Communication forwarding on busy user – CFB, refer 3GPP TS 22.082 [4] and 3GPP TS 24.604 [132]
10 Communication forwarding on no reply – CFNR, refer 3GPP TS 22.082 [4] and 3GPP TS 24.604 [132]
11 Communication forwarding on subscriber not reachable – CFNRc, refer 3GPP TS 22.082 [4] and
3GPP TS 24.604 [132]
12 Communication forwarding on not logged-in – CFNL, refer 3GPP TS 24.604 [132]
13 Communication diversion notification – CDIVN, refer 3GPP TS 24.604 [132]
14 Communication waiting – CW, refer 3GPP TS 22.083 [5] and 3GPP TS 24.615 [137]
Additional CW specific information can be provided in:
+CMCCSS1 (in parameter <service>)
+CMCCSS6 (in parameter <priority>)
15 Communication hold – HOLD, refer 3GPP TS 22.083 [5] and 3GPP TS 24.610 [135]
16 Conference – MPTY / CONF, refer 3GPP TS 22.084 [22] and 3GPP TS 24.605 [133]
17 Explicit communication transfer – ECT, refer 3GPP TS 22.091 [30] and 3GPP TS 24.629 [139]
18 Completion of communications to busy subscriber – CCBS, refer 3GPP TS 22.093 [123] and
3GPP TS 24.642 [140]
19 Completion of communications by no reply – CCNR, refer 3GPP TS 24.642 [140]
20 Communication barring of all outgoing calls – BAOC, refer 3GPP TS 22.088 [6] and 3GPP TS 24.611 [136]
21 Communication barring of all international outgoing calls except those directed to the home PLMN country –
BOIC-exHC, refer 3GPP TS 22.088 [6] and 3GPP TS 24.611 [136]
22 Communication barring of all incoming calls – BAIC, refer 3GPP TS 22.088 [6] and 3GPP TS 24.611 [136]
23 Communication barring of incoming calls when roaming outside the home PLMN country – BIC-Roam,
refer 3GPP TS 22.088 [6] and 3GPP TS 24.611 [136]
24 All Barring services, refer 3GPP TS 22.030 [19]
25 All outGoing barring services, refer 3GPP TS 22.030 [19]
26 All inComing barring services, refer 3GPP TS 22.030 [19]
27 Anonymous communication rejection – ACR, refer 3GPP TS 22.088 [6] and 3GPP TS 24.611 [136]
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
193
3GPP TS 27.007 version 13.3.0 Release 13
28 Advice of charge – AOC, refer 3GPP TS 22.085 [21] and 3GPP TS 24.654 [121]
29 Message waiting indication – MWI, refer 3GPP TS 24.606 [134]
30 Malicious communication identification, all outgoing calls – MCID, refer 3GPP TS 24.616 [l38]
31 Unstructured Supplementary Service Data – USSD, refer 3GPP TS 22.090 [23] and 3GPP TS 24.390 [131]
32 Customized Alerting Tones – CAT, refer 3GPP TS 24.182 [127]
33 Customized Ringing Signal – CRS, refer 3GPP TS 24.183 [128]
34 Flexible Alerting – FA, refer 3GPP TS 24.239 [129]
35 Personal Network Management – PNM, refer 3GPP TS 24.259 [130]
36 User-to-user signalling service 1 – UUS 1, refer 3GPP TS 22.087 [58] and 3GPP TS 24.229 [89]
37 User-to-user signalling service 2 – UUS 2, refer 3GPP TS 22.087 [58]
38 User-to-user signalling service 3 – UUS 3, refer 3GPP TS 22.087 [58]
39 All user-to-user signalling services, refer 3GPP TS 22.087 [58]
40 Follow me – FM, refer 3GPP TS 22.094 [124]
41 Multiple subscriber profile – MSP, refer 3GPP TS 22.097 [125]
42 Multicall – MC, refer 3GPP TS 22.135 [126]
43 enhanced multi-level precedence and pre-emption service – eMLPP, refer 3GPP TS 22.067 [54]
44 Closed User Group – CUG, refer 3GPP TS 22.085 [21] and 3GPP TS 24.654 [121]
Additional CUG specific information can be provided in:
+CMCCSS1 (in parameter <service>)
+CMCCSS7 (in parameter <CUG_index>)
256 - 511 Reserved for vendor specific services
<CLI_validity>: integer type. This parameter can provide details why <number> does not contain a calling
party BCD number (refer 3GPP TS 24.008 [8] subclause 10.5.4.30). The parameter is not relevant for MO call
types.
0 CLI valid
1 CLI has been withheld by the originator (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Reject by user")
2 CLI is not available due to interworking problems or limitations of originating network (refer
3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code "Interaction with other service")
3 CLI is not available due to calling party being of type payphone (refer 3GPP TS 24.008 [8]
table 10.5.135a/3GPP TS 24.008 code "
Coin line/payphone
")
4 CLI is not available due to other reasons (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Unavailable")
When CLI is not available (<CLI_validity>=2, <CLI_validity>=3 or <CLI_validity>=4),
<number> shall be an empty string ("") and <ton> value will not be significant. The parameter
<numbertype> will be set to 0. Nevertheless, TA may return the recommended value 128 for <ton>
(TON/NPI unknown in accordance with 3GPP TS 24.008 [8] subclause 10.5.4.7).
When CLI has been withheld by the originator, (<CLI validity>=1) and the CLIP is provisioned with the
"override category" option (refer 3GPP TS 22.081 [3] and 3GPP TS 23.081 [40]), <number> and <ton> is
provided. Otherwise, TA shall return the same setting for <number> and <type> as if the CLI was not
available. The parameter <numbertype> shall be set as applicable.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
194
3GPP TS 27.007 version 13.3.0 Release 13
<name>: string type up to 80 characters long string containing the calling name.
<subaddr>: string type subaddress of format specified by <satype>.
<satype>: type of subaddress octet in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.8) or
RFC 4715 [122] appendix A.
<priority>: integer type indicating the eMLPP priority level of the call, values specified in
3GPP TS 22.067 [54].
<CUG_index>: string type. The parameter sets the CUG index for this <CUG_pointer>.
"0" ... "32767" CUG index
"" no CUG index, indicated by empty string. Preferential CUG taken from subscriber data.
Implementation
Optional.
8.74 List of current calls +CLCCS
Table 8.74-1: +CLCCS action command syntax
Command
Possible response(s)
+CLCCS[=<ccidx>] [+CLCCS: <ccid1>,<dir>,<neg_status_present>,<neg_status>
,<SDP_md>,<cs_mode>,<ccstatus>,<mpty>,[,<numbertype>,<to
n>,<number>[,<priority_present>,<priority>[,<CLI_validit
y_present>,<CLI_validity>]]]
[<CR><LF>+CLCCS: <ccid2>,<dir>,<neg_status_present>,<neg
_status>,<SDP_md>,<cs_mode>,<ccstatus>,<mpty>,[,<numbert
ype>,<ton>,<number>[,<priority_present>,<priority>[,<CLI
_validity_present>,<CLI_validity>]]]
[...]]]
+CME ERROR: <err>
+CLCCS=?
Description
Returns a list of current calls controlled by the MT for which the <ccidx> is allocated. The information returned is a
subset of the information provided by the call monitoring function, see +CMCCS and its unsolicited result codes
+CMCCSI and +CMCCSS<x> / +CMCCSSEND. For an originating call, the parameters <numbertype>, <ton> and
<number> provide the number (line identity) information which has been dialled with +CDU or ATD. For a
terminating call, the parameters <numbertype>, <ton> and <number> provide the number (line identity)
information of the calling user. If no particular <ccidx> is included in the request, data for all allocated <ccidx> are
returned. If the command succeeds but no <ccidx> is allocated, no information response is sent to the TE. Refer
subclause 9.2 for possible <err> values.
Defined values
<ccidx>: integer type. Call identification number (see 3GPP TS 22.030 [19] subclause 6.5.5.1). This number can
be used in +CHLD command operations. Value range is from 1 to N. N, the maximum number of simultaneous
call control processes is implementation specific.
NOTE 1: The restrictions and limitations of the call identification number as described in 3GPP TS 22.030 [19]
subclause 6.5.5.1 and 3GPP TS 22.084 [22] do not apply.
NOTE 2: When +CMCCS is supported, the call identification number is not reset until the unsolicited result code
+CMCCSI has indicated that the <ccstatus>=1 (Idle).
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
195
3GPP
TS 27.007 version 13.3.0 Release 13
<dir>: integer type
0 mobile originated (MO) call
1 mobile terminated (MT) call
<neg_status_present>: integer type. Indicates whether parameter <neg_status> has any valid
information
0 No valid information in parameter <neg_status>. Parameter <neg_status> is set to zero.
1 Valid information in parameter <neg_status>.
<neg_status>: integer type as defined in the +CCMMD command
0 The parameter <neg_status> has no valid content. Parameter <SDP_md> is set to an empty string ("").
1 The <SDP_md> parameter describes the active media in the call.
2 The <SDP_md> parameter describes a proposed but not yet active new set of media for the call.
3 A proposed new set of media for the call was accepted by the remote party. The <SDP_md> parameter
describes the active media in the call (if any).
4 A proposed new set of media for the call was rejected by the remote party. The <SDP_md> parameter
describes the active media in the call (if any).
<SDP_md>: string type represented with IRA characters. SDP media description as per the +CDEFMP command.
This parameter shall not be subject to conventional character conversion as per +CSCS. This parameter will be
an empty string ("") if the call has no multimedia content.
<cs_mode>: integer type (bearer/teleservice)
0 no relevant information about bearer/teleservice
1 voice
2 data
3 fax
4 voice followed by data, voice mode
5 alternating voice/data, voice mode
6 alternating voice/fax, voice mode
7 voice followed by data, data mode
8 alternating voice/data, data mode
9 alternating voice/fax, fax mode
255 unknown
<ccstatus>: integer type. Indicating the state of the call.
1 Idle
2 Calling (MO); the call setup has been started
3 Connecting (MO); the call is in progress
4 Alerting (MO): an alert indication has been received
5 Alerting (MT); an alert indication has been sent
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
196
3GPP TS 27.007 version 13.3.0 Release 13
6 Active; the connection is established
7 Released; an outgoing (MO) call is released.
8 Released; an incoming (MT) call is released
9 User Busy
10 User Determined User Busy
11 Call Waiting (MO)
12 Call Waiting (MT)
13 Call Hold (MO)
14 Call Hold (MT)
<mpty>: integer type
0 call is not one of multiparty (conference) call parties
1 call is one of multiparty (conference) call parties
<numbertype>: integer type. Indicating type of information in parameter <number>.
0 No valid information in parameter <number>
1 Number in <number> according to URI including the prefix specifying the URI type (see command +CDU).
Parameter <ton> has no relevant information and is set to zero.
2 Number in <number> according to one of the formats supported by 3GPP TS 24.008 [8]
subclause 10.5.4.7)
<ton>: type of number in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7). The parameter is also set
to zero when it has no meaningful content, e.g. when <numbertype>=1.
<number>: string type phone number in format specified by <numbertype>. This parameter shall not be subject
to conventional character conversion as per +CSCS.
<priority_present>: integer type. Indicates whether parameter <priority> has any valid information
0 No valid information in parameter <priority>. Parameter <priority> is set to zero.
1 Valid information in parameter <priority>.
<priority>: integer type parameter indicating the eMLPP priority level of the call, values specified in
3GPP TS 22.067 [54]
<CLI_validity_present>: integer type. Indicates whether parameter <CLI_validity> has any valid
information
0 No valid information in parameter <CLI_validity>. Parameter <priority> is set to zero.
1 Valid information in parameter <CLI_validity>.
<CLI_validity>: integer type. This parameter can provide details why <number> does not contain a calling
party BCD number (refer 3GPP TS 24.008 [8] subclause 10.5.4.30). The parameter is not relevant for MO call
types.
0 CLI valid
1 CLI has been withheld by the originator (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Reject by user")
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
197
3GPP TS 27.007 version 13.3.0 Release 13
2 CLI is not available due to interworking problems or limitations of originating network (refer
3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code "Interaction with other service")
3 CLI is not available due to calling party being of type payphone (refer 3GPP TS 24.008 [8]
table 10.5.135a/3GPP TS 24.008 code "
Coin line/payphone
")
4 CLI is not available due to other reasons (refer 3GPP TS 24.008 [8] table 10.5.135a/3GPP TS 24.008 code
"Unavailable")
When CLI is not available (<CLI_validity>=2, <CLI_validity>=3 or <CLI_validity>=4),
<number> shall be an empty string ("") and <type> value will not be significant. The parameter
<numbertype> will be set to 0. Nevertheless, TA may return the recommended value 128 for <ton>
(TON/NPI unknown in accordance with 3GPP TS 24.008 [8] subclause 10.5.4.7).
When CLI has been withheld by the originator, (<CLI validity>=1) and the CLIP is provisioned with the
"override category" option (refer 3GPP TS 22.081 [3] and 3GPP TS 23.081 [40]), <number> and <type> is
provided. Otherwise, TA shall return the same setting for <number> and <type> as if the CLI was not
available. The parameter <numbertype> shall be set as applicable.
Implementation
Optional. Recommended when +CHLD command is implement.
This command supports all types of numbers (including SIP URIs) and can replace +CLCC.
8.75 Supported radio accesses +CSRA
Table 8.75-1: +CSRA parameter command syntax
Command
Possible response(s)
+CSRA=<GERAN-TDMA>,<UTRAN-
FDD>,<UTRAN-TDD-
LCR>,<UTRAN-TDD-
HCR>,<UTRAN-TDD-VHCR>,<E-
UTRAN-FDD>,<E-UTRAN-TDD>
+CME ERROR: <err>
+CSRA? +CSRAC: <GERAN-TDMA>,<UTRAN-FDD>,<UTRAN-TDD-
LCR>,<UTRAN-TDD-HCR>,<UTRAN-TDD-VHCR>,<E-
UTRAN-FDD>,<E-UTRAN-TDD>
<CR><LF>+CSRAA: <GERAN-TDMA>,<UTRAN-
FDD>,<UTRAN-TDD-LCR>,<UTRAN-TDD-HCR>,<UTRAN-
TDD-VHCR>,<E-UTRAN-FDD>,<E-UTRAN-TDD>
+CME ERROR: <err>
+CSRA=? +CSRA: (indication of supported <GERAN-TDMA>),(indication
of supported <UTRAN-FDD>),(indication of supported <UTRAN-
TDD-LCR>),(indication of supported <UTRAN-TDD-
HCR>),(indication of supported <UTRAN-TDD-
VHCR>),(indication of supported <E-UTRAN-FDD>),(
indication
of supported <E-UTRAN-TDD>)
+CME ERROR: <err>
Description
Set command is used to configure the availability of the radio accesses inherently supported by the MT. E.g. in a GSM-
only environment, other radio access technologies could be disabled to reduce power-consumption. Settings are
persistent over a power-cycle. It is not supported to set all parameters to indicate "Radio access is disabled", this will
cause the MT to return ERROR. +CSRA only configures the requested parameters; no change in the transmit and receive
RF circuits takes place by using +CSRA. The actual execution of the configuration is obtained by using +CFUN=128.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
198
3GPP TS 27.007 version 13.3.0 Release 13
Read command returns two lines of information text with two distinct prefixes:
- a line prefixed with +CSRAC: displaying the currently configured +CSRA settings. These values are not
activated until +CFUN=128 is executed, and this line does therefore not necessarily reflect the RATs currently
activated on the radio interface; and
- a line prefixed with +CSRAA: displaying the RATs currently activ on the radio interface.
Read command returns the current settings in the MT.
Refer subclause 9.2 for possible <err> values.
Test command returns values supported by the MT as compound values. The returned values do not reflect network
capabilities.
Defined values
<GERAN-TDMA>: integer type. Indicates usage of radio access of type GERAN TDMA, see 3GPP TS 45.001 [146].
The initial value is manufacturer specific.
0 Radio access is disabled
1 Radio access is enabled
<UTRAN-FDD>: integer type. Indicates usage of radio access of type UTRAN FDD, see 3GPP TS 25.212 [144].
The initial value is manufacturer specific.
0 Radio access is disabled
1 Radio access is enabled
<UTRAN-TDD-LCR>: integer type. Indicates usage of radio access of type UTRAN 1.28 Mcps TDD low chip rate
(TD-SCDMA), see 3GPP TS 25.102 [143]. The initial value is manufacturer specific.
0 Radio access is disabled
1 Radio access is enabled
<UTRAN-TDD-HCR>: integer type. Indicates usage of radio access of type UTRAN 3.84 Mcps TDD high chip rate,
see 3GPP TS 25.102 [143]. The initial value is manufacturer specific.
0 Radio access is disabled
1 Radio access is enabled
<UTRAN-TDD-VHCR>: integer type. Indicates usage of radio access of type UTRAN 7.68 Mcps TDD very high
chip rate, see 3GPP TS 25.102 [143]. The initial value is manufacturer specific.
0 Radio access is disabled
1 Radio access is enabled
<E-UTRAN-FDD>: integer type. Indicates usage of radio access of type E-UTRAN FDD, see
3GPP TS 36.300 [145]. The initial value is manufacturer specific.
0 Radio access is disabled
1 Radio access is enabled
<E-UTRAN-TDD>: integer type. Indicates usage of radio access of type E-UTRAN TDD, see
3GPP TS 36.300 [145]. The initial value is manufacturer specific.
0 Radio access is disabled
1 Radio access is enabled
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
199
3GPP TS 27.007 version 13.3.0 Release 13
Implementation
Optional. Mandatory when +CFUN supports <fun>=128.
8.76 Circuit switched fallback +CCSFB
Table 8.76-1: +CCSFB parameter command syntax
Command
Possible response(s)
+CCSFB=[<n>] +CME ERROR: <err>
+CCSFB? +CCSFB: <n>
+CCSFB=? +CCSFB: (list of supported <n>s)
Description
The set command is used to control circuit switched fallback (CSFB) operation. Reporting of CSFB related CS paging
requests can be switched on or off. After reporting the command can be used to accept or reject the CSFB call. The
command can also be used to control automatic acceptance/rejection of CSFB calls. Refer subclause 9.2 for possible
<err> values.
CS paging requests are reported with unsolicited result code +CCSFBU in the format:
+CCSFBU: <numbertype>,<ton>,<number>[,<ss_code>[,<lcs_indicator>[,<lcs_client_id
entity>]]]
NOTE 1: The command +CCSFB applies to connected mode. It does not apply to idle mode.
Read command returns the current value of <n>.
Test command returns values supported as a compound value.
Defined values
<n>: integer type.
0 disable reporting of CSFB related CS paging requests and disable automatic acceptance/rejection of CSFB
calls.
1 enable reporting of CSFB related CS paging requests and disable automatic acceptance/rejection of CSFB
calls.
2 enable reporting of CSFB related CS paging requests and enable automatic acceptance of CSFB calls.
3 enable reporting of CSFB related CS paging requests and enable automatic rejection of CSFB calls.
4 disable reporting of CSFB related CS paging requests and enable automatic acceptance of CSFB calls.
5 disable reporting of CSFB related CS paging requests and enable automatic rejection of CSFB calls.
6 accept CSFB call. This value can be used only after having received the unsolicited result code +CCSFBU
when automatic acceptance/rejection of CSFB calls has been disabled.
7 reject CSFB call. This value can be used only after having received the unsolicited result code +CCSFBU
when automatic acceptance/rejection of CSFB calls has been disabled.
NOTE 2: The values <n>=6 and <n>=7 will not be reported by +CCSFB? as these values are not associated with
any MT state.
<numbertype>: integer type. Indicating type of information in parameter <number>.
0 No valid information in parameter <number>. <number> shall then be set to empty string ("").
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
200
3GPP TS 27.00
7 version 13.3.0 Release 13
1 Number in <number> according to URI including the prefix specifying the URI type (see command +CDU).
Parameter <ton> has no relevant information and is set to zero.
2 Number in <number> according to one of the formats supported by 3GPP TS 24.008 [8] subclause 10.5.4.7.
NOTE 3: In +CCSFBU, the parameter <numbertype> can have value 2 only.
<ton>: type of number in integer format (refer 3GPP TS 24.008 [8] subclause 10.5.4.7). The parameter is also set
to zero when it has no meaningful content, e.g. when <numbertype>=1.
<number>: string type phone number in format specified by <numbertype>. The used character set should be
the one selected with Select TE Character Set +CSCS. When no number is available, <number> shall be set to
empty string ("").
<ss_code>: integer type. SS code (refer 3GPP TS 24.301 [83] subclause 9.9.3.39).
<lcs_indicator>: integer type. LCS indicator value (refer 3GPP TS 24.301 [83] subclause 9.9.3.40).
<lcs_client_identity>: string type. LCS client identity information in hexadecimal format (refer
3GPP TS 24.301 [83] subclause 9.9.3.41).
Implementation
Optional.
8.77 Informative examples
Phone Activity Status (+CPAS) is a general command used to detect the presence of the MT, if there is an incoming
call, or if there is a call in progress. This command is normally used before trying to operate the MT from the TE. Note
that the activity status can change at any time after the execution of +CPAS, and hence the returned value can be
obsolete. Detachment of the MT from the TA is indicated with a special final result code that indicates all errors related
to the operation of the MT. Result code is +CME ERROR: <err>, where <err> is an integer or verbose value giving
useful information about the reason for the command failure (refer subclause "Mobile Termination error result code
+CME ERROR").
Set Phone Functionality (+CFUN) can be used to reset the MT or set the power consumption level of the MT by
disabling certain parts of the MT (e.g. the transmit and receive RF circuits). Mobile Termination Control Mode
(+CMEC) is a command which manages access sharing between the MT and the TE to operate the user interface of the
MT. It has four subparameters which describe the access to keypad, display, indicators, and touch screen. Each
subparameter has values for restricting the operation of the corresponding user interface part only to the MT or only to
the TE, or to give the access for both of them.
Keypad Control command (+CKPD) is used to operate the keypad of the MT. Here lies the problem of different keypad
types between manufacturers, and also between their MT models. The keypresses are sent to the MT as a string type
subparameter of this command. Each character in that string represents a key which will be logically pressed. A special
character (colon) followed by any character can be used by manufacturers (or TE application programmers) to represent
a key which is not defined in this profile. An escape character (semicolon) for direct string entering is also defined. All
text between single semicolon characters is treated as an alphanumeric entry and is not converted to keypressings. All
semicolon characters inside the text is duplicated in the TE and stripped back to one before entering them to the MT.
Command has also optional second and third parameters which can be used to alter the time to strike each key, and the
pause to wait between keystrokes (in tenths of a second). A special pause character (W or w) can be added in the string
type subparameter for an extra pause of the same length as given by the third subparameter. In the following example
alphanumeric mode is entered and a person predefined in the MT phonebook, "Ilkka", is called; each key is struck for
half a second and pauses between strokes are a tenth of a second:
AT+CKPD="@:Ilkka:S",5,1
OK
Display Control command (+CDIS) is used both for writing to the display text fields and for reading the current status
of the fields. Mobile Termination usually has a character set of its own, so the TA will do a conversion between the TE
and the MT character sets. TE can have several character sets and the TA must be informed of the character set in use
before starting to write or read the display. Character set is set with general command Select TE Character Set +CSCS.
The +CDIS=? query command is a way to get information about the length of the fields. In the following example an
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
201
3GPP TS 27.007 version 13.3.0 Release 13
MT is first queried about the supported conversions and the lengths of the fields. The response shows there are three ten
character long and two six character long fields. Then the TE character set is set to be IRA and the current status of the
display is read. The last command writes the text "Hello, I'm writing to display" in the three fields, and keeps the
contents of the two other fields same (the last two commas could also be left out).
AT+CSCS=?;+CDIS=?
+CSCS: ("IRA","PCCP850","8859-1")
+CDIS: 10,10,10,6,6
OK
AT+CSCS="IRA"
OK
AT+CDIS?
+CDIS: "RADIOLINJA","","","Menu","Memory"
OK
AT+CDIS="IRA","Hello, I'm","writing to","display",,
OK
The writing is possible only when it is permitted by the Mobile Termination Control Mode command (and by the
manufacturer). If a certain field is not writable (but is readable), writing to it is ignored. The order of the text fields is
determined by manufacturers and follow the rule: first field is in the upper left corner, second in the next field to the
right, and so on, until to the last field in the lower right corner.
Touch screen action Control command (+CTSA) is used to operate the touch screen of the MT. The x, y coordinates of
the phone are fixed even if the device's orientation is changed. In the following example commands are sent to the MT
to emulate a user drawing on the ME's touch screen; it is relevant that the gesture starts from the top of the touch screen.
A gesture is emulated, starting at location 10,10 in a non-display area of the ME"s (touch) screen, then dragged to 50,50
(during which the gesture crosses the boundary between the non-display area and a display area), then dragged to
100,100 and finally the touch screen is released at location 100,100.
AT+CSO=? obtain the touch screen orientation
+CSO=2,0
AT+CSS=? obtain the touch screen size
+CSS=200,600
AT+CDSB=? determine if a boundary between the non-display area and a display area exists, and its location
+CDSB=20,20,180,580
AT+CTSA=1,10,10 start emulating a gesture
AT+CTSA=1,50,50 emulate that the gesture crosses the boundary between non-display area and a display area
+CTSA=0,100,100 end emulating the gesture
Indicators can be handled with Indicator Control command (+CIND). Its query command returns a short description
(abbreviation) of the purpose of the indicators and the supported values for each indicator. The setting and reading is
done similarly as with Display Control command. In the following example the indicators of a phone are queried, their
current value is read, and the value of message indicator is tried to set (but it is forbidden):
AT+CIND=?
+CIND: ("memory",(0-2)),("call",(0,1)),("data",(0,1)),("roam",(0,1)),
("alpha",(0,1)),("message",(0,1)),("index1",(0-11)),("index2",(0-11)),
("index3",(0-11)),("signal",(0-5)),("service",(0,1)),("sel1",(0,1)),
("sel2",(0,1)),("sel3",(0,1)),("battchg",(0-5))
OK
AT+CIND?
+CIND: 1,0,0,0,0,1,0,0,0,3,1,0,0,0,5
OK
AT+CIND=,,,,,0
+CME ERROR: 10
The subparameter order in the command is defined by the query command order, not by the actual display order. The
zero value of an indicator means that it is off (or in state which can be identified as "off"-state), value one means that
the indicator is on (or in a state which is more substantial than "off"-state), value two is more substantial than one, and
so on.
To this point, only operating through the TE is covered. But when MT can be operated also through its keypad, or touch
screen, or there are changes in the status of the display elements, the information about these actions is given to the TE
also. This can be solved only with unsolicited result codes which return keypad, display text and indicator, and touch
screen events. Each event group has a result code of its own: +CKEV returns the key code and if the key pressed (1) or
released (0), +CDEV returns the display text field running number (as specified by command +CDIS) and the new
status of the field, and +CIEV returns the running number of the indicator (refer +CIND) and the new value of it, and
+CTEV returns the location of the action performed on the touch screen. In the following example number key 1 is
13
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
202
3GPP TS 27.007 version 13.3.0 Release 13
pressed, updated on the display, released, and signal strength changes its state to five, the touch screen is pressed at
coordinates 10,10, and it is released at the same coordinates, 3 seconds after initially pressing the screen:
+CKEV: 49,1
+CDEV: 1,"1"
+CKEV: 49,0
+CIND: 10,5
+CTEV: 1,10,10,0;
+CTEV: 0,10,10,0,3000
Mobile Termination Event Reporting command (+CMER) has been specified for the purpose of controlling the sending
of these unsolicited result codes to the TE. Four ways are provided to handle the buffering of the result codes (see
figure 8). The first is to buffer them always. The second possibility is to discard them when in on-line data mode and
otherwise forward them directly to the TE. The third possibility is to buffer them in data mode and otherwise forward
them to the TE. The last possibility is to send them always to the TE (some inband technique - e.g. V.80 - is used in data
mode to send the result codes within the data). This is the first subparameter of +CMER command. Next three
subparameters are used to enable or disable each of the keypad, text field and indicator result codes. Sending codes can
be enabled either so that only events generated from the MT user interface are returned, or so that also events caused by
Keypad, Display and Indicator Control commands are returned. The fifth subparameter controls the flushing of the
buffer when the value of the first subparameter is changed to a value from one to three.
Figure 8: Mobile termination event reporting
An example of complete setup of the TA where TE takes the control of keypad, but does not want to write to display
nor control the indicators (in the start MT is powered off):
AT+CMEE=2;+CREG=1 (use verbose <err> values; report registration)
OK
AT+CPAS (query MT status)
+CPAS: 5 (MT is asleep)
OK
AT+CFUN=1 (set MT to full functionality state)
+CME ERROR: SIM PIN required (SIM requests PIN)
AT+CPIN="1234"
+CME ERROR: incorrect password (user entered wrong PIN)
AT+CPIN="4321"
OK (correct PIN)
AT+COPS=0,0 (ask for automatic operator selection and registration)
OK
+CREG: 1 (registered in the network)
AT+COPS?
+COPS: 0,0,"RADIOLINJA" (get the operator name)
OK
AT+CMEC=1,0,0 (take over the keypad, leave display to MT)
OK
AT+CDIS=?;+CIND=? (query display text and indicator formats)
+CDIS: 10,10,10,6,6
+CIND: ("memory",(0-2)),("call",(0,1)),("data",(0,1)),("roam",(0,1)),
("alpha",(0,1)),("message",(0,1)),("index1",(0-11)),("index2",(0-11)),
("index3",(0-11)),("signal",(0-5)),("service",(0,1)),("sel1",(0,1)),
("sel2",(0,1)),("sel3",(0,1)),("battchg",(0-5))
OK
COMMAND
MODE DATA MODE
Buffer
TE
MT
TA
MT events (inband)
0
1
2
3
+CMER first
subparameter
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
203
3GPP TS 27.007 version 13.3.0 Release 13
AT+CSCS="IRA" (set TE character set for display text results)
OK
AT+CMER=1,0,2,2,0 (return display text and indicator result codes when
OK in command state, in data mode discard them)
AT+CDIS?;+CIND? (read current state of display texts and indicators)
+CDIS: "",""," 12345","Menu","Memory" (user had pressed number buttons before
+CIND: 1,0,0,0,0,1,0,0,0,3,1,0,0,0,5 TE took control with +CMEC)
OK
AT+CKPD="C",20 (clear main display text '12345' by holding the
OK 'clear' button down two seconds)
+CDEV: 3,"1234" (first only one character deleted)
+CDEV: 3,"" (while holding continues, whole display is cleared)
+CDEV: 1,"RADIOLINJA" (operator name comes to the display)
The start of the previous example could go as follows when MT has already been powered on but is waiting for the
PIN:
AT+CMEE=2;+CREG=1 (use verbose <err> values; report registration)
OK
AT+CPAS (query MT status)
+CPAS: 0 (MT is ready to receive commands)
OK
AT+CPIN? (is MT asking passwords?)
+CPIN: SIM PIN (yes, SIM PIN required)
AT+CPIN="4321"
OK (correct PIN)
One of the most regular operations done through the MT user interface is phonebook control. To lessen the workload of
the TE, some direct commands for phonebook reading and writing are practical. Command Select Phonebook Memory
Storage +CPBS query version returns supported phonebook memories, read version returns current settings, and set
version selects the memory. For GSM, the normal storages are SIM, MT and TA.
Read Phonebook Entries (+CPBR) can be used to read either one or many phonebook locations at the same time. A
regular phonebook entry consists of three elements: memory index number, the phone number and its alphanumeric
equivalent given by the user. Query version of this returns supported index values of the selected memory, and the
maximum lengths of the number and alphanumeric elements. The query version of the Write Phonebook Entry
command (+CPBW) is similar, but the action version sets or clears an entry in the phonebook. Find Phonebook Entries
(+CPBF) can be used to search alphanumeric entries starting with specific string. An example where the whole
phonebook of the MT is read, index number four is cleared, and number three is written:
AT+CPBS=?
+CPBS: ("ME","SM") (MT and SIM have phonebooks)
OK
AT+CPBS="ME" (select MT memory)
OK
AT+CPBR=? (read index range and element lengths)
+CPBR: (1-99),30,30
OK
AT+CPBR=1,99 (read all entries but only the ones set are returned)
+CPBR: 1,"931123456",129,"Ilkka"
+CPBR: 2,"9501234567",129,""
+CPBR: 4,"901234567",129,"Hesari"
OK
AT+CPBW=4;+CPBW=3,"921123456",,"TS" (clear index 4 and write index 3)
OK
Circuit switched fallback (+CCSFB) can be used to control circuit switched fallback operation. Reporting of CSFB
related CS paging requests can be switched on or off by +CCSFB=1 and +CCSFB=0. CSFB related CS paging requests
are reported with unsolicited result code +CCSFBU. CSFB calls can be automatically accepted or rejected by
+CCSFB=2, +CCSFB=3, +CCSFB=4 and +CCSFB=5. CSFB calls can be manually accepted or rejected by
+CCSFB=6 and +CCSFB=7. In the example the ME interrogates the current CSFB settings, enables reporting and
accepts a CSFB call:
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
204
3GPP TS 27.007 version 13.3.0 Release 13
AT+CCSFB=?
+CCSFB: 0 (reporting and automatic acceptance/rejection disabled)
OK
AT+CCSFB=1 (enable reporting)
OK
+CCSFBU: 2,1,12345678,17 (incoming CSFB paging request with clip supplementary service)
AT+CCSFB=6 (accept CSFB call)
OK
9 Mobile termination errors
9.1 Report mobile termination error +CMEE
Table 110: +CMEE parameter command syntax
Command
Possible response(s)
+CMEE=[<n>]
+CMEE? +CMEE: <n>
+CMEE=?
+CMEE: (list of supported <n>s)
Description
Set command disables or enables the use of final result code +CME ERROR: <err> as an indication of an error
relating to the functionality of the MT. When enabled, MT related errors cause +CME ERROR: <err> final result
code instead of the regular ERROR final result code. ERROR is returned normally when error is related to syntax, invalid
parameters, or TA functionality.
Read command returns the current setting of <n>.
Test command returns values supported as a compound value.
Defined values
<n>: integer type.
0 disable +CME ERROR: <err> result code and use ERROR instead
1 enable +CME ERROR: <err> result code and use numeric <err> values (refer subclause 9.2)
2 enable +CME ERROR: <err> result code and use verbose <err> values (refer subclause 9.2)
Implementation
Mandatory for <n> values 0 and 1.
9.1A Report mobile originated location request error +CMOLRE
Table 9.1A-1: +CMOLRE parameter command syntax
Command
Possible response(s)
+CMOLRE=[<n>]
+CMOLRE? +CMOLRE: <n>
+CMOLRE=?
+CMOLRE: (list of supported <n>s)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
205
3GPP TS 27.007 versio
n 13.3.0 Release 13
Description
Set command disables or enables the verbose format of unsolicited result code +CMOLRE: <err> as an indication of
an error relating to the functionality for the mobile originated location request (MO-LR) error reporting format. When
enabled, MT related verbose error cause is given.
Read command returns the current setting of <n>.
Test command returns values supported as a compound value.
Defined values
<n>: integer type.
0 disable. This will give +CMOLRE: <err> result code with numeric <err> values (refer subclause 9.3)
1 enable. This will give +CMOLRE: <err> result code with verbose <err> values (refer subclause 9.3)
Implementation
Optional.
9.1B Report network error codes +CNEC
Table 9.1B-1: +CNEC parameter command syntax
Command
Possible response(s)
+CNEC=[<n>]
+CNEC? +CNEC: <n>
+CNEC=? +CNEC: (list of supported <n>s)
Description
The command activates or deactivates unsolicited reporting of error codes sent by the network. When activated, based
on the setting of <n>, the ME will report CS mobility management, GPRS mobility management, GPRS session
management, EPS mobility management and EPS session management related error codes sent by the network. The
following unsolicited result codes can be reported:
- +CNEC_MM: <error_code> CS Mobility Management
- +CNEC_GMM: <error_code> GPRS Mobility Management
- +CNEC_GSM: <error_code>[,<cid>] GPRS Session Management
- +CNEC_EMM: <error_code>[,<cid>] EPS Mobility Management
- +CNEC_ESM: <error_code>[,<cid>] EPS Session Management
The parameter <n> is specified as a sum of integers, each representing the category of error codes that the MT is
interested in receiving.
The read command returns the current setting of <n>.
Test command returns the supported values as a compound value.
Parameters
<n>: integer type. The parameter is a sum of integers each representing a certain category of error codes. The value
consists of the sum of the individual values for <n> for the required unsolicited result codes.
0 Disable unsolicited error reporting
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
206
3GPP TS 27.007 version 13.3.0 Release 13
1 Enable unsolicited result code +CNEC_MM to report CS mobility management errors coded as specified in
3GPP TS 24.008 [8] Table 10.5.95/3GPP TS 24.008
2 Enable unsolicited result code +CNEC_GMM to report GPRS mobility management errors coded as specified
in 3GPP TS 24.008 [8] Table 10.5.147/3GPP TS 24.008
4 Enable unsolicited result code +CNEC_GSM to report GPRS session management errors coded as specified in
3GPP TS 24.008 [8] Table 10.5.157/3GPP TS 24.008
8 Enable unsolicited result code +CNEC_EMM to report EPS mobility management errors coded as specified in
3GPP TS 24.301 [83] Table 9.9.3.9.1
16 Enable unsolicited result code +CNEC_ESM to report EPS session management errors coded as specified in
3GPP TS 24.301 [83] Table 9.9.4.4.1
NOTE: The sequence of entering +CNEC=1, followed by +CNEC=4 does not yield the same result as +CNEC=5,
as +CNEC=4 overwrites the previous setting.
Example: If the MT wants to receive only CS mobility management errors, then <n>=1 must be specified.
AT+CNEC=1
If the MT wants to receive CS mobility management errors and GPRS session management errors,
then <n>=5 must be specified (1 for enabling CS mobility management error and 4 for enabling
GPRS session management error).
AT+CNEC=5
To enable reporting of all error codes, then <n>=31 must be specified (equals 1+2+4+8+16).
AT+CNEC=31
<error_code>: integer type. Error codes as appropriate according to:
3GPP TS 24.008 [8] Table 10.5.95/3GPP TS 24.008 for CS mobility management errors codes
3GPP TS 24.008 [8] Table 10.5.147/3GPP TS 24.008 for GPRS mobility management errors codes
3GPP TS 24.008 [8] Table 10.5.157/3GPP TS 24.008 for GPRS session management errors codes
3GPP TS 24.301 [83] Table 9.9.3.9.1 for EPS mobility management errors codes
3GPP TS 24.301 [83] Table 9.9.4.4.1 for EPS session management errors codes.
<cid>: integer type. Specifies a particular PDP context definition.
Implementation
Optional.
9.2 Mobile termination error result code +CME ERROR
9.2.0 General
The operation of +CME ERROR: <err> final result code is similar to the regular ERROR result code: if
+CME ERROR: <err> is the result code for any of the commands in a command line, none of the following
commands in the same command line is executed (neither ERROR nor OK result code shall be returned as a result of a
completed command line execution). The format of <err> can be either numeric or verbose. This is set with command
+CMEE (refer subclause 9.1).
NOTE: ITU-T Recommendation V.250 [14] command V does not affect the format of this result code.
<err> values (numeric format followed by verbose format):
13
ETSI
ETSI TS 1
27 007 V13.3.0 (2016
-
03)
207
3GPP TS 27.007 version 13.3.0 Release 13
All values below 256 are reserved.
Values in the range 0 - 100 are reserved for general errors.
Values in the range 101 - 150 are reserved for use by GPRS and EPS.
Values in the range 151 - 170 are reserved for use by VBS/VGCS and eMLPP.Values in the range 171 - 256 can be
used by GPRS or by EPS.
9.2.1 General errors
Numeric Text
0 phone failure
1 no connection to phone
2 phone-adaptor link reserved
3 operation not allowed
4 operation not supported
5 PH-SIM PIN required
6 PH-FSIM PIN required
7 PH-FSIM PUK required
10 SIM not inserted (See NOTE 1)
11 SIM PIN required
12 SIM PUK required
13 SIM failure (See NOTE 1)
14 SIM busy (See NOTE 1)
15 SIM wrong (See NOTE 1)
16 incorrect password
17 SIM PIN2 required
18 SIM PUK2 required
20 memory full
21 invalid index
22 not found
23 memory failure
24 text string too long
25 invalid characters in text string
26 dial string too long
27 invalid characters in dial string
30 no network service
31 network timeout
32 network not allowed - emergency calls only
40 network personalization PIN required
41 network personalization PUK required
42 network subset personalization PIN required
43 network subset personalization PUK required
44 service provider personalization PIN required
45 service provider personalization PUK required
46 corporate personalization PIN required
47 corporate personalization PUK required
48 hidden key required (See NOTE 2)
49 EAP method not supported
50 Incorrect parameters
51 command implemented but currently disabled
52 command aborted by user
53 not attached to network due to MT functionality restrictions
54 modem not allowed - MT restricted to emergency calls only
55 operation not allowed because of MT functionality restrictions
56 fixed dial number only allowed - called number is not a fixed dial number (refer 3GPP TS 22.101 [147])
57 temporarily out of service due to other MT usage
58 language/alphabet not supported
59 unexpected data value
60 system failure
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
208
3GPP TS 27.007 version 13.3.0 Release 13
61 data missing
62 call barred
63 message waiting indication subscription failure
100 unknown
NOTE 1: This error code is also applicable to UICC.
NOTE 2: This key is required when accessing hidden phonebook entries.
9.2.2 GPRS and EPS-related errors
9.2.2.1 Errors related to a failure to perform an attach
Numeric Text
103 Illegal MS (#3)
106 Illegal ME (#6)
107 GPRS services not allowed (#7)
108 GPRS services and non-GPRS services not allowed (#8)
111 PLMN not allowed (#11)
112 Location area not allowed (#12)
113 Roaming not allowed in this location area (#13)
114 GPRS services not allowed in this PLMN (#14)
115 No Suitable Cells In Location Area (#15)
122 Congestion (#22)
125 Not authorized for this CSG (#25)
172 Semantically incorrect message (#95)
173 Mandatory information element error (#96)
174 Information element non-existent or not implemented (#97)
175 Conditional IE error (#99)
176 Protocol error, unspecified (#111)
NOTE: Values in parentheses are 3GPP TS 24.008 [8] cause codes.
9.2.2.2 Errors related to a failure to activate a context
Numeric Text
177 Operator Determined Barring (#8)
126 insufficient resources (#26)
127 missing or unknown APN (#27)
128 unknown PDP address or PDP type (#28)
129 user authentication failed (#29)
130 activation rejected by GGSN, Serving GW or PDN GW (#30)
131 activation rejected, unspecified (#31)
132 service option not supported (#32)
133 requested service option not subscribed (#33)
134 service option temporarily out of order (#34)
140 feature not supported (#40)
141 semantic error in the TFT operation (#41)
142 syntactical error in the TFT operation (#42)
143 unknown PDP context (#43)
144 semantic errors in packet filter(s) (#44)
145 syntactical errors in packet filter(s) (#45)
146 PDP context without TFT already activated (#46)
149 PDP authentication failure
178 maximum number of PDP contexts reached (#65)
179 requested APN not supported in current RAT and PLMN combination (#66)
180 request rejected, Bearer Control Mode violation (#48)
NOTE 1: Values in parentheses are 3GPP TS 24.008 [8] cause codes.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
209
3GPP TS 27.007 version 13.3.0 Release 13
Numeric Text
181 unsupported QCI value (#83)
NOTE 2: Values in parentheses are 3GPP TS 24.301 [83] cause codes.
9.2.2.3 Errors related to a failure to disconnect a PDN
Numeric Text
171 Last PDN disconnection not allowed (#49)
NOTE 1: This error is returned when the MT detects an attempt to disconnect the last PDN or the network returns a
response message with cause value #49.
NOTE 2: Values in parentheses are 3GPP TS 24.301 [83] cause codes.
NOTE 3: The numeric error code for "Last PDN disconnection not allowed (#49)" changed to 171 since
3GPP Rel-11.
9.2.2.4 Other GPRS errors
Numeric Text
148 unspecified GPRS error
150 invalid mobile class
9.2.3 VBS, VGCS and eMLPP-related errors
Numeric Text
151 VBS/VGCS not supported by the network
152 No service subscription on SIM
153 No subscription for group ID
154 Group Id not activated on SIM
155 No matching notification
156 VBS/VGCS call already present
157 Congestion
158 Network failure
159 Uplink busy
160 No access rights for SIM file
161 No subscription for priority
162 operation not applicable or not possible
163 Group Id prefixes not supported
164 Group Id prefixes not usable for VBS
165 Group Id prefix value invalid
Implementation
Mandatory for numeric format codes applicable to implemented command set.
9.3 Mobile termination error result code +CMOLRE
9.3.1 General
The operation of +CMOLRE: <err> unsolicited result code is similar to the regular ERROR result code. The format of
<err> can be either numeric or verbose. This is set with command +CMOLRE (refer subclause 9.1a).
<err> values (numeric format followed by verbose format):
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
210
3GPP TS 27.007 version 13.3.0
Release 13
9.3.2 Errors
Numeric Text
0 Method not supported
1 Additional assistance data reqired
2 Not enough satellites
3 UE busy (See NOTE)
4 Network error
5 Failed to open internet connection, too many connections
6 Failed to open internet connection, too many users
7 Failure due to handover
8 Internet connection failure
9 Memory error
255 Unknown error
NOTE: Error code 3 (UE busy) indicates there is already one ongoing positioning session and the UE does not
support multiple simultaneous sessions
9.4 Informative examples
An example of TA responses with all three +CMEE values when MT manufacturer identification is requested but MT is
not connected to the TA:
AT+CMEE=0 (+CME ERROR shall not be used)
OK
AT+CGMI
ERROR
AT+CMEE=1 (use numeric <err>)
OK
AT+CGMI
+CME ERROR: 1
AT+CMEE=2 (use verbose <err>)
OK
AT+CGMI
+CME ERROR: no connection to phone
10 Commands for packet domain
10.0 General
This clause defines commands that a TE can use to control a MT supporting packet switched services. Some aspects of
a Packet Domain MT are described in 3GPP TS 27.060 [34].
It is anticipated that Packet Domain MTs will vary widely in functionality. At one extreme, a MT supporting CS/PS or
class-A mode of operation might support multiple PDP types as well as circuit switched data, and use multiple external
networks and QoS profiles. At the other extreme a MT supporting only PS or class-C mode of operation might support
only a single PDP type using a single external network, and rely on the HLR to contain the PDP context definition.
A comprehensive set of Packet Domain-specific commands is defined in subclause 10.1 to provide the flexibility
needed by the more complex MT. The commands are designed to be expandable to accommodate new PDP types and
interface protocols, merely by defining new values for many of the parameters. Multiple contexts can be activated if the
interface link-layer protocol is able to support them. The commands use the extended information and error message
capabilities described in this specification.
For MTs of intermediate complexity, most commands have simplified forms where certain parameters can be omitted.
For the simplest MTs, and for backwards compatibility with existing communications software, it is possible to control
access to the Packet Domain using existing modem-compatible commands. A special dial-string syntax is defined for
use with the D command. This "modem compatible" mode of operation is described in subclause 10.2.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
211
3GPP TS 27.007 version 13.3.0 Release 13
A discussion on the interaction of the AT commands, Packet Domain Management and Packet Data Protocols, together
with examples of command sequences for a number of applications can be found in 3GPP TS 27.060 [34].
10.1 Commands specific to MTs supporting the packet domain
10.1.0 General remark about EPS bearer contexts and PDP contexts
Accordingly to 3GPP TS 23.401 [82], there is a 1 to 1 mapping between active EPS bearer context and active PDP
context:
- An active default EPS bearer context is associated with an active non secondary PDP context.
- An active dedicated EPS bearer context is associated with an active secondary PDP context.
In consequence to the implicit logical relation between EPS PDN connection and its associated Default EPS Bearer,
hereafter a same non secondary PDP context identifier <p_cid> can be used to refer either an EPS PDN connection
context or its associated Default EPS Bearer context.
As dedicated EPS bearer contexts are activated by the network, the network can then activate a new dedicated EPS
bearer or modify an existing one to fulfil the request.For bearer resources activated by the network a context identifier is
allocated by the MT/TA.
For easy reading the term PDP context is used for PDP contexts in UMTS/GPRS as well as PDN/default EPS bearers
and traffic flows in EPS.
The feature "initial PDP context" may be supported and is a manufacturer specific option. For this option, the context
with <cid>=0 (context number 0) is defined upon startup and does not need to be created with the +CGDCONT
command. The initial PDP context has particular manufacturer specific default settings disassociated with any other
default settings of +CGDCONT. When in E-UTRAN or according to the AT-command +CIPCA in GERAN and
UTRAN, the initial PDP context is automatically activated by the MT following a successful registration to the
network. If all active contexts are deactivated, the initial PDP context can be (re)established. This is manufacturer
specific and depends on the current RAT as well as how the active contexts are deactivated.
NOTE: Care must be taken to secure that repetitive PDP context activations / deactivations are not performed and
that PDP contexts are not activated in situations where it is a determined choice by the terminal or the
network to discontinue connectivity. Examples of such deliberate discontinuation of connectivity are the
AT-commands +CGATT=0 or +CGACT=0, receipt of a detach request from the network with "re-attach
not required" or when all PDP contexts are deactivated by the network
.
Table 10.1.0-1: AT commands/results applicable for EPS
(equivalence between PDP context / PDN Connection or Default EPS Bearer)
AT commands Comments
+CGDCONT Used to define PDN connection for EPS.
+CGACT Used to activate a bearer resource for EPS.
+CGCONTRDP Used to show dynamically allocated PDN parameters.
+CGEV: xxx ... Used to indicate EPS bearers operations status.
Table 10.1.0-2: AT commands/results applicable for EPS
(equivalence between PDP context / EPS Bearer Resources)
AT commands Comments
+CGACT Used to activate a modification of a PDP context or
EPS bearer resource.
ETSI
ETSI TS 127 007 V
13.3.0 (2016
-
03)
212
3GPP TS 27.007 version 13.3.0 Release 13
+CGDSCONT Used to define EPS Bearer Resource for a specific
PDN for EPS.
+CGSCONTRDP Used to show dynamically allocated EPS Bearer
Resource parameters.
+CGCMOD Used to request a modification of a PDP context or
EPS Bearer Resource.
+CGTFT Used to define a Traffic Flow Template for a PDP
context or a Traffic Flow Aggregate for an EPS bearer
resource.
+CGTFTRDP Used to show the network assigned Traffic Flow
Template for an EPS bearer resource.
+CGEQOS Used to define the EPS bearer resource Quality of
Service parameter.
In UMTS/GPRS mode this would hold a mapping
function to the UMTS/GPRS QoS parameters.
+CGEQOSRDP Used to show the network assigned EPS QoS
parameters for an EPS bearer resource.
In UMTS/GPRS mode this would hold a mapping
function to the UMTS/GPRS QoS parameters.
+CGEV: xxx ... Used to indicate EPS PDN connection and bearer
resources operations status
Table 10.1.0-3: AT commands applicable for EPS
AT commands Comments
+CGATT Used to attach/detach the MT from the Packet Domain
service.
10.1.1 Define PDP context +CGDCONT
Table 111: +CGDCONT parameter command syntax
Command
Possible response(s)
+CGDCONT=[<cid>[,<PDP_type>[,<APN>[,<PD
P_addr>[,<d_comp>[,<h_comp>[,<IPv4AddrA
lloc>[,<request_type>[,<P-
CSCF_discovery>[,<IM_CN_Signalling_Flag
_Ind>[,<NSLPI>[,<securePCO>[,<IPv4_MTU_
discovery>][,<Local_Addr_Ind>]]]]]]]]]]
]]]
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
213
3GPP TS 27.007 version 13.3.0 Release 13
+CGDCONT? [+CGDCONT: <cid>,<PDP_type>,<APN>,<PDP_a
ddr>,<d_comp>,<h_comp>[,<IPv4AddrAlloc>[
,<request_type>[,<P-
CSCF_discovery>[,<IM_CN_Signalling_Flag_
Ind>[,<NSLPI>[,<securePCO>[,<IPv4_MTU_di
scovery>[,<Local_Addr_Ind>]]]]]]]]]
[<CR><LF>+CGDCONT: <cid>,<PDP_type>,<APN
>,<PDP_addr>,<d_comp>,<h_comp>[,<IPv4Add
rAlloc>[,<request_type>[,<P-
CSCF_discovery>[,<IM_CN_Signalling_Flag_
Ind>[,<NSLPI>[,<securePCO>[,<IPv4_MTU_di
scovery>[,<Local_Addr_Ind>]]]]]]]]
[...]]
+CGDCONT=? +CGDCONT: (range of supported
<cid>s),<PDP_type>,,,(list of supported
<d_comp>s),(list of supported <h_comp>s),(list of
supported <IPv4AddrAlloc>s),(list of supported
<request_type>s),(list of supported <P-
CSCF_discovery>s),(list of supported
<IM_CN_Signalling_Flag_Ind>s) ,(list of
supported <NSLPI>s),(list of supported
<securePCO>s),(list of supported
<IPv4_MTU_discovery>s),(list of supported
<Local_Addr_Ind>s)
[<CR><LF>+CGDCONT: (range of supported
<cid>s),<PDP_type>,,,(list of supported
<d_comp>s),(list of supported <h_comp>s),(list of
supported <IPv4AddrAlloc>s),(list of supported
<request_type>s),(list of supported <P-
CSCF_discovery>s),(list of supported
<IM_CN_Signalling_Flag_Ind>s) ,(list of
supported <NSLPI>s),(list of supported
<securePCO>s,(list of supported
<IPv4_MTU_discovery>s),(list of supported
<Local_Addr_Ind>s)
[...]]
Description
The set command specifies PDP context parameter values for a PDP context identified by the (local) context
identification parameter, <cid> and also allows the TE to specify whether security protected transmission of ESM
information is requested, because the PCO can include information that requires ciphering. There can be other reasons
for the UE to use security protected transmission of ESM information, e.g. if the UE needs to transfer an APN. The
number of PDP contexts that may be in a defined state at the same time is given by the range returned by the test
command.
For EPS the PDN connection and its associated EPS default bearer is identified herewith.
A special form of the set command, +CGDCONT=<cid> causes the values for context number <cid> to become
undefined.
If the initial PDP context is supported, the context with <cid>=0 is automatically defined at startup, see
subclause 10.1.0. As all other contexts, the parameters for <cid>=0 can be modified with +CGDCONT. If the initial
PDP context is supported, +CGDCONT=0 resets context number 0 to its particular default settings.
The read command returns the current settings for each defined context.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
214
3GPP TS 27.007 version 13.3.0 Release 13
The test command returns values supported as compound values. If the MT supports several PDP types, <PDP_type>,
the parameter value ranges for each <PDP_type> are returned on a separate line.
Defined values
<cid>: integer type; specifies a particular PDP context definition. The parameter is local to the TE-MT interface
and is used in other PDP context-related commands. The range of permitted values (minimum value = 1 or if the
initial PDP context is supported (see subclause 10.1.0), minimum value = 0) is returned by the test form of the
command.
NOTE 1: The <cid>s for network-initiated PDP contexts will have values outside the ranges indicated for the
<cid> in the test form of the commands +CGDCONT and +CGDSCONT.
<PDP_type>: string type; specifies the type of packet data protocol. The default value is manufacturer specific.
X.25 ITU-T/CCITT X.25 layer 3 (Obsolete)
IP Internet Protocol (IETF STD 5 [103])
IPV6 Internet Protocol, version 6 (see RFC 2460 [106])
IPV4V6 Virtual <PDP_type> introduced to handle dual IP stack UE capability. (See
3GPP TS 24.301 [83])
OSPIH Internet Hosted Octect Stream Protocol (Obsolete)
PPP Point to Point Protocol (IETF STD 51 [104])
NOTE 2: Only IP, IPV6 and IPV4V6 values are supported for EPS services.
<APN>: string type; a logical name that is used to select the GGSN or the external packet data network.
If the value is null or omitted, then the subscription value will be requested.
<PDP_addr>: string type; identifies the MT in the address space applicable to the PDP.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the read form
of +CGDCONT.
NOTE 3: The value of this parameter is ignored with the set command. The parameter is included in the set
command for backwards compatibility reasons only.
<d_comp>: integer type; controls PDP data compression (applicable for SNDCP only) (refer
3GPP TS 44.065 [61])
0 off
1 on (manufacturer preferred compression)
2 V.42bis
3 V.44
<h_comp>: integer type; controls PDP header compression (refer 3GPP TS 44.065 [61] and 3GPP TS 25.323 [62])
0 off
1 on (manufacturer preferred compression)
2 RFC 1144 [105] (applicable for SNDCP only)
3 RFC 2507 [107]
4 RFC 3095 [108] (applicable for PDCP only)
<IPv4AddrAlloc>: integer type; controls how the MT/TA requests to get the IPv4 address information
\N
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
215
3GPP TS 27.007 version 13.3.0 Release
13
0 IPv4 address allocation through NAS signalling
1 IPv4 address allocated through DHCP
<request_type>: integer type; indicates the type of PDP context activation request for the PDP context, see
3GPP TS 24.301 [83] (subclause 6.5.1.2) and 3GPP TS 24.008 [8] (subclause 10.5.6.17). If the initial PDP
context is supported (see subclause 10.1.0) it is not allowed to assign <cid>=0 for emergency bearer services.
According to 3GPP TS 24.008 [8] (subclause 4.2.4.2.2 and subclause 4.2.5.1.4) and 3GPP TS 24.301 [83]
(subclause 5.2.2.3.3 and subclause 5.2.3.2.2), a separate PDP context must be established for emergency bearer
services.
NOTE 4: If the PDP context for emergency bearer services is the only activated context, only emergency calls are
allowed, see 3GPP TS 23.401 [82] subclause 4.3.12.9.
0 PDP context is for new PDP context establishment or for handover from a non-3GPP access network (how
the MT decides whether the PDP context is for new PDP context establishment or for handover is
implementation specific)
1 PDP context is for emergency bearer services
2 PDP context is for new PDP context establishment
3 PDP context is for handover from a non-3GPP access network
<P-CSCF_discovery>: integer type; influences how the MT/TA requests to get the P-CSCF address, see
3GPP TS 24.229 [89] annex B and annex L.
0 Preference of P-CSCF address discovery not influenced by +CGDCONT
1 Preference of P-CSCF address discovery through NAS signalling
2 Preference of P-CSCF address discovery through DHCP
<IM_CN_Signalling_Flag_Ind>: integer type; indicates to the network whether the PDP context is for IM
CN subsystem-related signalling only or not.
0 UE indicates that the PDP context is not for IM CN subsystem-related signalling only
1 UE indicates that the PDP context is for IM CN subsystem-related signalling only
<NSLPI>: integer type; indicates the NAS signalling priority requested for this PDP context:
0 indicates that this PDP context is to be activated with the value for the low priority indicator configured in
the MT.
1 indicates that this PDP context is is to be activated with the value for the low priority indicator set to "MS is
not configured for NAS signalling low priority".
NOTE 5: The MT utilises the provide NSLPI information as specified in 3GPP TS 24.301 [83] and
3GPP TS 24.008 [8].
<securePCO>: integer type. Specifies if security protected transmission of PCO is requested or not (applicable for
EPS only, see 3GPP TS 23.401 [82] subclause 6.5.1.2).
0 Security protected transmission of PCO is not requested
1 Security protected transmission of PCO is requested
<IPv4_MTU_discovery>: integer type; influences how the MT/TA requests to get the IPv4 MTU size, see
3GPP TS 24.008 [8] subclause 10.5.6.3.
0 Preference of IPv4 MTU size discovery not influenced by +CGDCONT
1 Preference of IPv4 MTU size discovery through NAS signalling
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
216
3GPP TS 27.007 version 13.3.0 Release 13
<Local_Addr_Ind>: integer type; indicates to the network whether or not the MS supports local IP address in
TFTs (see 3GPP TS 24.301 [83] and 3GPP TS 24.008 [8] subclause 10.5.6.3).
0 indicates that the MS supports local IP address in TFTs
1 indicates that the MS does not support local IP address in TFTs
Implementation
Mandatory unless only a single subscribed context is supported.
10.1.2 Define secondary PDP context +CGDSCONT
Table 112: +CGDSCONT parameter command syntax
Command
Possible response(s)
+CGDSCONT=[<cid>,<p_cid>[,<d_comp>[,<h_
comp>[,<IM_CN_Signalling_Flag_Ind>]]]]
+CGDSCONT? [+CGDSCONT: <cid>,<p_cid>,<d_comp>,<h_co
mp>,<IM_CN_Signalling_Flag_Ind>]
[<CR><LF>+CGDSCONT: <cid>,<p_cid>,<d_com
p>,<h_comp>,<IM_CN_Signalling_Flag_Ind>
[...]]
+CGDSCONT=? +CGDSCONT: (range of supported <cid>s),(list of
<p_cid>s for active primary contexts),(list of supported
<d_comp>s),(list of supported <h_comp>s),(list of
supported <IM_CN_Signalling_Flag_Ind>s)
Description
The set command specifies PDP context parameter values for a Secondary PDP context identified by the (local) context
identification parameter, <cid>. The number of PDP contexts that may be in a defined state at the same time is given
by the range returned by the test command.
In EPS the command is used to define traffic flows.
A special form of the set command, +CGDSCONT=<cid> causes the values for context number <cid> to become
undefined.
NOTE: If the initial PDP context is supported, the context with <cid>=0 is automatically defined at startup, see
subclause 10.1.0.
The read command returns the current settings for each defined context.
The test command returns values supported as compound values.
Defined values
<cid>: integer type; which specifies a particular PDP context definition. The parameter is local to the TE-MT
interface and is used in other PDP context-related commands. The range of permitted values (minimum value =
1) is returned by the test form of the command.
NOTE: The <cid>s for network-initiated PDP contexts will have values outside the ranges indicated for the
<cid> in the test form of the commands +CGDCONT and +CGDSCONT.
<p_cid>: integer type; specifies a particular PDP context definition which has been specified by use of the
+CGDCONT command. The parameter is local to the TE-MT interface. The list of permitted values is returned by
the test form of the command.
<d_comp>: integer type; controls PDP data compression (applicable for SNDCP only) (refer
3GPP TS 44.065 [61])
ETSI
ETSI TS 127 007 V13.3.0 (
2016
-
03)
217
3GPP TS 27.007 version 13.3.0 Release 13
0 off
1 on (manufacturer preferred compression)
2 V.42bis
3 V.44
<h_comp>: integer type; controls PDP header compression (refer 3GPP TS 44.065 [61] and 3GPP TS 25.323 [62])
0 off
1 on (manufacturer preferred compression)
2 RFC 1144 [105] (applicable for SNDCP only)
3 RFC 2507 [107]
4 RFC 3095 [108] (applicable for PDCP only)
<IM_CN_Signalling_Flag_Ind>: integer type; indicates to the network whether the PDP context is for IM
CN subsystem-related signalling only or not.
0 UE indicates that the PDP context is not for IM CN subsystem-related signalling only
1 UE indicates that the PDP context is for IM CN subsystem-related signalling only
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
218
3GPP TS 27.007 version 13.3.0 Release 13
10.1.3 Traffic flow template +CGTFT
Table 113: +CGTFT parameter command syntax
Command
Possible Response(s)
+CGTFT=[<cid>,[<packet filter
identifier>,<evaluation precedence
index>[,<remote address and subnet
mask>[,<protocol number (ipv4) / next
header (ipv6)>[,<local port
range>[,<remote port range>[,<ipsec
security parameter index (spi)>[,<type
of service (tos) (ipv4) and mask /
traffic class (ipv6) and mask>[,<flow
label (ipv6)>[,<direction>[,<local
address and subnet mask>]]]]]]]]]]]
+CM
E
ERROR: <err>
+CGTFT? [+CGTFT: <cid>,<packet filter
identifier>,<evaluation precedence
index>,<remote address and subnet
mask>,<protocol number (ipv4) / next
header (ipv6)>,<local port
range>,<remote port range>,<ipsec
security parameter index (spi)>,<type
of service (tos) (ipv4) and mask /
traffic class (ipv6) and mask>,<flow
label (ipv6)>,<direction>,<local
address and subnet mask>]
[<CR><LF>+CGTFT: <cid>,<packet filter
identifier>,<evaluation precedence
index>,<remote address and subnet
mask>,<protocol number (ipv4) / next
header (ipv6)>,<local port range>,
<remote port range>,<ipsec security
parameter index (spi)>,<type of service
(tos) (ipv4) and mask / traffic class
(ipv6) and mask>,<flow label
(ipv6)>,<direction>,<local address and
subnet mask>
[...]]
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
219
3GPP TS 27.007 version 13.3.0 Release 13
Command
Possible Response(s)
+CGTFT=? +CGTFT: <PDP_type>,(list of supported <packet
filter identifier>s),(list of supported
<evaluation precedence index>s),(list of
supported <remote address and subnet
mask>s),(list of supported <protocol number
(ipv4) / next header (ipv6)>s),(list of
supported <local port range>s),(list of
supported <remote port range>s),(list of
supported <ipsec security parameter index
(spi)>s),(list of supported <type of service
(tos) (ipv4) and mask / traffic class
(ipv6) and mask>s),(list of supported <flow
label (ipv6)>s),(list of supported
<direction>s),(list of supported <local
address and subnet mask>s)
[<CR><LF>+CGTFT: <PDP_type>,(list of
supported <packet filter identifier>s),(list
of supported <evaluation precedence
index>s),(list of supported <remote address
and subnet mask>s),(list of supported
<protocol number (ipv4) / next header
(ipv6)>s),(list of supported <local port
range>s),(list of supported <remote port
range>s),(list of supported <ipsec security
parameter index (spi)>s),(list of supported
<type of service (tos) (ipv4) and mask
/ traffic class (ipv6) and mask>s),(list
of supported <flow label (ipv6)>s),(list of
supported <direction>s),(list of supported
<local address and subnet mask>s)
[...]]
Description
This command allows the TE to specify a Packet Filter - PF for a Traffic Flow Template - TFT that is used in the
GGSN in UMTS/GPRS and Packet GW in EPS for routing of packets onto different QoS flows towards the TE. The
concept is further described in the 3GPP TS 23.060 [47]. A TFT consists of from one and up to 16 Packet Filters, each
identified by a unique <packet filter identifier>. A Packet Filter also has an <evaluation
precedence index> that is unique within all TFTs associated with all PDP contexts that are associated with the
same PDP address.
The set command specifies a Packet Filter that is to be added to the TFT stored in the MT and used for the context
identified by the (local) context identification parameter, <cid>. The specified TFT will be stored in the GGSN in
UMTS/GPRS and Packet GW in EPS only at activation or MS-initiated modification of the related context. Since this is
the same parameter that is used in the +CGDCONT and +CGDSCONT commands, the +CGTFT command is effectively
an extension to these commands. The Packet Filters consist of a number of parameters, each of which may be set to a
separate value.
A special form of the set command, +CGTFT=<cid> causes all of the Packet Filters in the TFT for context number
<cid> to become undefined. At any time there may exist only one PDP context with no associated TFT amongst all
PDP contexts associated to one PDP address. At an attempt to delete a TFT, which would violate this rule, an ERROR or
+CME ERROR response is returned. Extended error responses are enabled by the +CMEE command. Refer
subclause 9.2 for possible <err> values.
The read command returns the current settings for all Packet Filters for each defined context.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
220
3GPP TS 27.007 version 13.3.0 Release 13
The test command returns values supported as compound values. If the MT supports several PDP types, the parameter
value ranges for each PDP type are returned on a separate line. TFTs shall be used for PDP-type IP and PPP only. For
PDP-type PPP a TFT is applicable only when IP traffic is carried over PPP. If PPP carries header-compressed IP
packets, then a TFT cannot be used.
Defined values
<cid>: integer type. Specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
<PDP_type>: string type. Specifies the type of packet data protocol (see the +CGDCONT command).
For the following parameters, see also 3GPP TS 23.060 [47]:
<packet filter identifier>: integer type. Value range is from 1 to 16.
<evaluation precedence index>: integer type. The value range is from 0 to 255.
<remote address and subnet mask>: string type. The string is given as dot-separated numeric (0-255)
parameters on the form:
"a1.a2.a3.a4.m1.m2.m3.m4" for IPv4 or
"a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16.m1.m2.m3.m4.m5.m6.m7.m8.m9.m10.m11.m12.m13.
m14.m15.m16", for IPv6.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the read form
of +CGTFT.
<protocol number (ipv4) / next header (ipv6)>: integer type. Value range is from 0 to 255.
<local port range>: string type. The string is given as dot-separated numeric (0-65535) parameters on the
form "f.t".
<remote port range>: string type. The string is given as dot-separated numeric (0-65535) parameters on the
form "f.t".
<ipsec security parameter index (spi)>: numeric value in hexadecimal format. The value range is
from 00000000 to FFFFFFFF.
<type of service (tos) (ipv4) and mask / traffic class (ipv6) and mask>:
string type. The string is given as dot-separated numeric (0-255) parameters on the form "t.m".
<flow label (ipv6)>: numeric value in hexadecimal format. The value range is from 00000 to FFFFF. Valid
for IPv6 only.
<direction>: integer type. Specifies the transmission direction in which the packet filter shall be applied.
0 Pre-Release 7 TFT filter (see 3GPP TS 24.008 [8], table 10.5.162)
1 Uplink
2 Downlink
3 Birectional (Up & Downlink)
<local address and subnet mask>: string type. The string is given as dot-separated numeric (0-255)
parameters on the form:
"a1.a2.a3.a4.m1.m2.m3.m4" for IPv4 or
"a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16.m1.m2.m3.m4.m5.m6.m7.m8.m9.m10.m11.m12.m13.
m14.m15.m16", for IPv6.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the read form
of +CGTFT.
Some of the above listed attributes may coexist in a Packet Filter while others mutually exclude each other, the possible
combinations are shown in 3GPP TS 23.060 [47].
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
221
3GPP TS 27.007 version 13.3.0 Release 13
Implementation
Optional.
10.1.4 Quality of service profile (requested) +CGQREQ
Table 114: +CGQREQ parameter command syntax
Command
Possible Response(s)
+CGQREQ=[<cid>[,<precedence>[,<delay>[,
<reliability>[,<peak>[,<mean>]]]]]]
+CGQREQ? [+CGQREQ: <cid>,<precedence>,<delay>,<r
eliability>,<peak>,<mean>]
[<CR><LF>+CGQREQ: <cid>,<precedence>,<d
elay>,<reliability>,<peak>,<mean>
[...]]
+CGQREQ=? +CGQREQ: <PDP_type>,(
list of supported
<precedence>s),(list of supported
<delay>s),(list of supported
<reliability>s),(list of supported
<peak>s),(list of supported <mean>s)
[<CR><LF>+CGQREQ: <PDP_type>,(list of
supported <precedence>s),(list of supported
<delay>s),(list of supported
<reliability>s),(list of supported
<peak>s),(list of supported <mean>s)
[...]]
Description
This command allows the TE to specify a Quality of Service Profile that is used when the MT activates a PDP context.
The set command specifies a profile for the context identified by the (local) context identification parameter, <cid>.
Since this is the same parameter that is used in the +CGDCONT and +CGDSCONT commands, the +CGQREQ command
is effectively an extension to these commands. The QoS profile consists of a number of parameters, each of which may
be set to a separate value.
A special form of the set command, +CGQREQ=<cid> causes the requested profile for context number <cid> to
become undefined.
The read command returns the current settings for each defined context.
The test command returns values supported as compound values. If the MT supports several PDP types, the parameter
value ranges for each PDP type are returned on a separate line.
Defined values
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
<PDP_type>: string type; specifies the type of packet data protocol (see the +CGDCONT command).
The following parameters are defined in 3GPP TS 23.107 [46]:
<precedence>: integer type; specifies the precedence class
<delay>: integer type; specifies the delay class
<reliability>: integer type; specifies the reliability class
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
222
3GPP TS 27.007 version 13.3.0 Release 13
<peak>: integer type; specifies the peak throughput class
<mean>: integer type; specifies the mean throughput class
If a value is omitted for a particular class then the value is considered to be unspecified.
Implementation
Optional. If the command is not implemented then all the values are considered to be unspecified.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
223
3GPP TS 27.007 version 13.3.0 Release 13
10.1.5 Quality of service profile (minimum acceptable) +CGQMIN
Table 115: +CGQMIN parameter command syntax
Command
Possible
Response(s)
+CGQMIN=[<cid>[,<precedence>[,<delay>[,
<reliability>[,<peak>[,<mean>]]]]]]
+CGQMIN? [+CGQMIN: <cid>,<precedence>,<delay>,<r
eliability>,<peak>,<mean>]
[<CR><LF>+CGQMIN: <cid>,<precedence>,<d
elay>,<reliability>,<peak>,<mean>
[...]]
+CGQMIN=? +CGQMIN: <PDP_type>,
(list of supported
<precedence>s),(list of supported
<delay>s),(list of supported
<reliability>s),(list of supported
<peak>s),(list of supported <mean>s)
[<CR><LF>+CGQMIN: <PDP_type>,(list of
supported <precedence>s),(list of supported
<delay>s),(list of supported
<reliability>s),(list of supported
<peak>s),(list of supported <mean>s)
[...]]
Description
This command allows the TE to specify a minimum acceptable profile which is checked by the MT against the
negotiated profile when the PDP context is activated.
The set command specifies a profile for the context identified by the (local) context identification parameter, <cid>.
Since this is the same parameter that is used in the +CGDCONT and +CGDSCONT commands, the +CGQMIN command
is effectively an extension to these commands. The QoS profile consists of a number of parameters, each of which may
be set to a separate value.
A special form of the set command, +CGQMIN=<cid> causes the minimum acceptable profile for context number
<cid> to become undefined. In this case no check is made against the negotiated profile.
The read command returns the current settings for each defined context.
The test command returns values supported as compound values. If the MT supports several PDP types, the parameter
value ranges for each PDP type are returned on a separate line.
Defined values
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
<PDP_type>: string type; specifies the type of packet data protocol (see the +CGDCONT command).
The following parameters are defined in 3GPP TS 23.107 [46]:
<precedence>: integer type; specifies the precedence class
<delay>: integer type; specifies the delay class
<reliability>: integer type; specifies the reliability class
<peak>: integer type; specifies the peak throughput class
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
224
3GPP TS 27.007 version 13.3.0 Release 13
<mean>: integer type; specifies the mean throughput class
If a value is omitted for a particular class then this class is not checked.
Implementation
Optional. If the command is not implemented then no check is made against the negotiated profile.
10.1.6 3G quality of service profile (requested) +CGEQREQ
Table 116: +CGEQREQ parameter command syntax
Command
Possible Response(s)
+CGEQREQ=[<cid>[,<Traffic
class>[,<Maximum bitrate UL>[,<Maximum
bitrate DL>[,<Guaranteed bitrate
UL>[,<Guaranteed bitrate DL>[,<Delivery
order>[,<Maximum SDU size>[,<SDU error
ratio>[,<Residual bit error
ratio>[,<Delivery of erroneous
SDUs>[,<Transfer delay>[,<Traffic
handling priority>[,<Source statistics
descriptor>[,<Signalling
indication>]]]]]]]]]]]]]]]
+CGEQREQ? [+CGEQREQ: <cid>,<Traffic
class>,<Maximum bitrate UL>,<Maximum
bitrate DL>, <Guaranteed bitrate
UL>,<Guaranteed bitrate DL>,<Delivery
order>,<Maximum SDU size>,<SDU error
ratio>,<Residual bit error
ratio>,<Delivery of erroneous
SDUs>,<Transfer delay>,<Traffic
handling priority>,<Source statistics
descriptor>,<Signalling indication>]
[<CR><LF>+CGEQREQ: <cid>,<Traffic
class>,<Maximum bitrate UL>,<Maximum
bitrate DL>,<Guaranteed bitrate
UL>,<Guaranteed bitrate DL>,<Delivery
order>,<Maximum SDU size>,<SDU error
ratio>,<Residual bit error
ratio>,<Delivery of erroneous
SDUs>,<Transfer delay>,<Traffic
handling priority>,<Source Statistics
Descriptor>,<Signalling Indication>
[...]]
+CGEQREQ=? +CGEQREQ: <PDP_type>,(list of supported
<Traffic class>s),(list of supported <Maximum
bitrate UL>s),(list of supported <Maximum
bitrate DL>s),(list of supported <Guaranteed
bitrate UL>s),(list of supported <Guaranteed
bitrate DL>s),(list of supported <Delivery
order>s),(list of supported <Maximum SDU
size>s),(list of supported <SDU error
ratio>s),(list of supported <Residual bit
error ratio>s),(list of supported <Delivery of
erroneous SDUs>s),(list of supported <Transfer
delay>s),(list of supported <Traffic handling
priority>s),(list of supported <Source
statistics descriptor>s),(list of supported
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
225
3GPP TS 27.007 version 13.3.0 Release 13
Command
Possible Response(s)
<Signalling indication>s)
[<CR><LF>+CGEQREQ: <PDP_type>,(list of
supported <Traffic class>s),(list of supported
<Maximum bitrate UL>s),(list of supported
<Maximum bitrate DL>s),(list of supported
<Guaranteed bitrate UL>s),(list of supported
<Guaranteed bitrate DL>s),(list of supported
<Delivery order>s),(list of supported <Maximum
SDU size>s),(list of supported <SDU error
ratio>s),(list of supported <Residual bit
error ratio>s),(list of supported <Delivery of
erroneous SDUs>s),(list of supported <Transfer
delay>s),(list of supported <Traffic handling
priority>s),(list of supported <Source
statistics descriptor>s),(list of supported
<Signalling indication>s)
[...]]
Description
This command allows the TE to specify a UMTS Quality of Service Profile that is used when the MT activates a PDP
context.
The set command specifies a profile for the context identified by the (local) context identification parameter, <cid>.
The specified profile will be stored in the MT and sent to the network only at activation or MS-initiated modification of
the related context. Since this is the same parameter that is used in the +CGDCONT and +CGDSCONT commands, the
+CGEQREQ command is effectively an extension to these commands. The QoS profile consists of a number of
parameters, each of which may be set to a separate value.
A special form of the set command, +CGEQREQ=<cid> causes the requested profile for context number <cid> to
become undefined.
The read command returns the current settings for each defined context.
The test command returns values supported as compound values. If the MT supports several PDP types, the parameter
value ranges for each PDP type are returned on a separate line.
Defined values
<cid>: integer type; specifies a particular PDP context definition (see +CGDCONT and +CGDSCONT commands).
<PDP_type>: string type; specifies the type of packet data protocol (see the +CGDCONT command).
For the following parameters, see also 3GPP TS 23.107 [46].
<Traffic class>: integer type; indicates the type of application for which the UMTS bearer service is
optimised (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 conversational
1 streaming
2 interactive
3 background
4 subscribed value
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
226
3GPP TS 27.007 version 13.3.0 Release 13
If the Traffic class is specified as conversational or streaming, then the Guaranteed and Maximum bitrate
parameters should also be provided.
<Maximum bitrate UL>: integer type; indicates the maximum number of kbits/s delivered to UMTS (up-link
traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQREQ=…,32, …).
This parameter should be provided if the Traffic class is specified as conversational or streaming (refer
3GPP TS 24.008 [8] subclause 10.5.6.5).
<Maximum bitrate DL>: integer type; indicates the maximum number of kbits/s delivered by UMTS (down-
link traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQREQ=…,32,
…). If the parameter is set to '0' the subscribed value will be requested. This parameter should be provided if the
Traffic class is specified as conversational or streaming (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Guaranteed bitrate UL>: integer type; indicates the guaranteed number of kbits/s delivered to UMTS (up-
link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be
specified as '32' (e.g. AT+CGEQREQ=…,32, …). If the parameter is set to '0' the subscribed value will be
requested. This parameter should be provided if the Traffic class is specified as conversational or streaming
(refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Guaranteed bitrate DL>: integer type; indicates the guaranteed number of kbits/s delivered by UMTS
(down-link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be
specified as '32' (e.g. AT+CGEQREQ=…,32, …). If the parameter is set to '0' the subscribed value will be
requested. This parameter should be provided if the Traffic class is specified as conversational or streaming
(refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Delivery order>: integer type; indicates whether the UMTS bearer shall provide in-sequence SDU delivery
or not (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 no
1 yes
2 subscribed value
<Maximum SDU size>: integer type; (1,2,3,…) indicates the maximum allowed SDU size in octets. If the
parameter is set to '0' the subscribed value will be requested (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<SDU error ratio>: string type; indicates the target value for the fraction of SDUs lost or detected as
erroneous. SDU error ratio is defined only for conforming traffic. The value is specified as 'mEe'. As an example
a target SDU error ratio of 5•10
-3
would be specified as "5E3" (e.g. AT+CGEQREQ=…,"5E3",…). "0E0" means
subscribed value (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Residual bit error ratio>: string type; indicates the target value for the undetected bit error ratio in the
delivered SDUs. If no error detection is requested, Residual bit error ratio indicates the bit error ratio in the
delivered SDUs. The value is specified as "mEe". As an example a target residual bit error ratio of 5•10
-3
would
be specified as "5E3" (e.g. AT+CGEQREQ=…,"5E3",…). "0E0" means subscribed value (refer
3GPP TS 24.008 [8] subclause 10.5.6.5).
<Delivery of erroneous SDUs>: integer type; indicates whether SDUs detected as erroneous shall be
delivered or not (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 no
1 yes
2 no detect
3 subscribed value
<Transfer delay>: integer type; (0,1,2,…) indicates the targeted time between request to transfer an SDU at
one SAP to its delivery at the other SAP, in milliseconds. If the parameter is set to '0' the subscribed value will
be requested (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
( )
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
227
3GPP
TS 27.007 version 13.3.0 Release 13
<Traffic handling priority>: integer type; (1,2,3,…) specifies the relative importance for handling of all
SDUs belonging to the UMTS bearer compared to the SDUs of other bearers. If the parameter is set to '0' the
subscribed value will be requested (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Source Statistics Descriptor>: integer type; specifies characteristics of the source of the submitted
SDUs for a PDP context. This parameter should be provided if the Traffic class is specified as conversational or
streaming (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 Characteristics of SDUs is unknown
1 Characteristics of SDUs corresponds to a speech source
<Signalling Indication>: integer type; indicates signalling content of submitted SDUs for a PDP context.
This parameter should be provided if the Traffic class is specified as interactive (refer 3GPP TS 24.008 [8]
subclause 10.5.6.5).
0 PDP context is not optimized for signalling
1 PDP context is optimized for signalling<PDP_type> (see +CGDCONT and +CGDSCONT commands).
If a value is omitted for a particular class then the value is considered to be unspecified.
NOTE: When in dual mode with EPS the MT provides a mapping function to EPS Quality of Service parameter
used for an EPS bearer resource activation request.
Implementation
Optional. If the command is not implemented then all the values are considered to be unspecified.
10.1.7 3G quality of service profile (minimum acceptable) +CGEQMIN
Table 117: +CGEQMIN parameter command syntax
Command
Possible Response(
s)
+CGEQMIN=[<cid>[,<Traffic
class>[,<Maximum bitrate UL>[,<Maximum
bitrate DL>[,<Guaranteed bitrate
UL>[,<Guaranteed bitrate DL>[,<Delivery
order>[,<Maximum SDU size>[,<SDU error
ratio>[,<Residual bit error
ratio>[,<Delivery of erroneous SDUs>
[,<Transfer delay>[,<Traffic handling
priority>[,<Source statistics
descriptor>[,<Signalling
indication>]]]]]]]]]]]]]]]
+CGEQMIN? [+CGEQMIN: <cid>,<Traffic
class>,<Maximum bitrate UL>,<Maximum
bitrate DL>,<Guaranteed bitrate
UL>,<Guaranteed bitrate DL>,<Delivery
order>,<Maximum SDU size>,<SDU error
ratio>,<Residual bit error
ratio>,<Delivery of erroneous
SDUs>,<Transfer delay>,<Traffic
handling priority>,<Source statistics
descriptor>,<Signalling indication>]
[<CR><LF>+CGEQMIN: <cid>,<Traffic
class>,<Maximum bitrate UL>,<Maximum
bitrate DL>,<Guaranteed bitrate
UL>,<Guaranteed bitrate DL>,<Delivery
order>,<Maximum SDU size>,<SDU error
ratio>,<Residual bit error
ratio>,<Delivery of erroneous
SDUs>,<Transfer delay>,<Traffic
( )
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
228
3GPP TS 27.007 version 13.3.0 Release 13
Command
Possible Response(
s)
handling priority>,<Source statistics
descriptor>,<Signalling indication>
[...]]
+CGEQMIN=? +CGEQMIN: <PDP_type>,(list of supported
<Traffic class>s),(list of supported <Maximum
bitrate UL>s),(list of supported <Maximum
bitrate DL>s),(list of supported <Guaranteed
bitrate UL>s),(list of supported <Guaranteed
bitrate DL>s),(list of supported <Delivery
order>s),(list of supported <Maximum SDU
size>s),(list of supported <SDU error
ratio>s),(list of supported <Residual bit
error ratio>s),(list of supported <Delivery of
erroneous SDUs>s),(list of supported <Transfer
delay>s),(list of supported <Traffic handling
priority>s),(list of supported <Source
statistics descriptor>s),(list of supported
<Signalling indication>s)
[<CR><LF>+CGEQMIN: <PDP_type>,(list of
supported <Traffic class>s),(list of supported
<Maximum bitrate UL>s),(list of supported
<Maximum bitrate DL>s),(list of supported
<Guaranteed bitrate UL>s),(list of supported
<Guaranteed bitrate DL>s),(list of supported
<Delivery order>s),(list of supported <Maximum
SDU size>s),(list of supported <SDU error
ratio>s),(list of supported <Residual bit
error ratio>s),(list of supported <Delivery of
erroneous SDUs>s),(list of supported <Transfer
delay>s),(list of supported <Traffic handling
priority>s),(list of supported <Source
statistics descriptor>s),(list of supported
<Signalling indication>s)
[...]]
Description
This command allows the TE to specify a minimum acceptable profile, which is checked by the MT against the
negotiated profile returned in the PDP context establishment and PDP contect modification procedures.
The set command specifies a profile for the context identified by the (local) context identification parameter, <cid>.
The specified profile will be stored in the MT and checked against the negotiated profile only at activation or MS-
initiated modification of the related context. Since this is the same parameter that is used in the +CGDCONT and
+CGDSCONT commands, the +CGEQMIN command is effectively an extension to these commands. The QoS profile
consists of a number of parameters, each of which may be set to a separate value.
A special form of the set command, +CGEQMIN=<cid> causes the minimum acceptable profile for context number
<cid> to become undefined. In this case no check is made against the negotiated profile.
The read command returns the current settings for each defined context.
The test command returns values supported as compound values. If the MT supports several PDP types, the parameter
value ranges for each PDP type are returned on a separate line.
Defined values
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
229
3GPP TS 27.007 version 13.3.0 Release 13
<cid>: integer type; specifies a particular PDP context definition (see +CGDCONT and +CGDSCONT commands).
<PDP_type>: string type; specifies the type of packet data protocol (see the +CGDCONT command).
For the following parameters, see also 3GPP TS 23.107 [46].
<Traffic class>: integer type; indicates the type of application for which the UMTS bearer service is
optimised (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 conversational
1 streaming
2 interactive
3 background
<Maximum bitrate UL>: integer type; indicates the maximum number of kbits/s delivered to UMTS (up-link
traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQMIN=…,32, …)
(refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Maximum bitrate DL>: integer type; indicates the maximum number of kbits/s delivered by UMTS (down-
link traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQMIN=…,32,
…) (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Guaranteed bitrate UL>: integer type; indicates the guaranteed number of kbits/s delivered to UMTS (up-
link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be
specified as '32' (e.g. AT+CGEQMIN=…,32, …) (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Guaranteed bitrate DL>: integer type; indicates the guaranteed number of kbits/s delivered by UMTS
(down-link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be
specified as '32' (e.g. AT+CGEQMIN=…,32, …) (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Delivery order>: integer type; indicates whether the UMTS bearer shall provide in-sequence SDU delivery
or not (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 no
1 yes
<Maximum SDU size>: integer type; (1,2,3,…) indicates the maximum allowed SDU size in octets (refer
3GPP TS 24.008 [8] subclause 10.5.6.5).
<SDU error ratio>: string type; indicates the target value for the fraction of SDUs lost or detected as
erroneous. SDU error ratio is defined only for conforming traffic. The value is specified as "mEe". As an
example a target SDU error ratio of 5•10
-3
would be specified as "5E3" (e.g. AT+CGEQMIN=…,"5E3",…)
(refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Residual bit error ratio>: string type; indicates the target value for the undetected bit error ratio in the
delivered SDUs. If no error detection is requested, Residual bit error ratio indicates the bit error ratio in the
delivered SDUs. The value is specified as "mEe". As an example a target residual bit error ratio of 5•10
-3
would
be specified as "5E3" (e.g. AT+CGEQMIN=…,"5E3",…) (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Delivery of erroneous SDUs>: integer type; indicates whether SDUs detected as erroneous shall be
delivered or not (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 no
1 yes
2 no detect
<Transfer delay>: integer type; (0,1,2,…) indicates the targeted time between request to transfer an SDU at
one SAP to its delivery at the other SAP, in milliseconds (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
230
3GPP TS 27.007 version 13.3.0 Release 13
<Traffic handling priority>: integer type; (1,2,3,…) specifies the relative importance for handling of all
SDUs belonging to the UMTS bearer compared to the SDUs of other bearers (refer 3GPP TS 24.008 [8]
subclause 10.5.6.5).
<Source Statistics Descriptor>: integer type; specifies characteristics of the source of the submitted
SDUs for a PDP context. This parameter should be provided if the Traffic class is specified as conversational or
streaming (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 Characteristics of SDUs is unknown
1 Characteristics of SDUs corresponds to a speech source
<Signalling Indication>: integer type; indicates signalling content of submitted SDUs for a PDP context.
This parameter should be provided if the Traffic class is specified as interactive (refer 3GPP TS 24.008 [8]
subclause 10.5.6.5).
0 PDP context is not optimized for signalling
1 PDP context is optimized for signalling
If a value is omitted for a particular class then the value is considered to be unspecified.
Implementation
Optional. If the command is not implemented then no check is made against the negotiated profile.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
231
3GPP TS 27.007 version 13.3.0 Release 13
10.1.8 3G quality of service profile (negotiated) +CGEQNEG
Table 118: +CGEQNEG action command syntax
Command
Possible Response(s)
+CGEQNEG[=<cid>[,<cid>[,...]]] [+CGEQNEG: <cid>,<Traffic
class>,<Maximum bitrate UL>,<Maximum
bitrate DL>,<Guaranteed bitrate
UL>,<Guaranteed bitrate DL>,<Delivery
order>,<Maximum SDU size>,<SDU error
ratio>,<Residual bit error
ratio>,<Delivery of erroneous
SDUs>,<Transfer delay>,<Traffic
handling priority>]
[<CR><LF>+CGEQNEG: <cid>,<Traffic
class>,<Maximum bitrate UL>,<Maximum
bitrate DL>,<Guaranteed bitrate
UL>,<Guaranteed bitrate DL>,<Delivery
order>,<Maximum SDU size>,<SDU error
ratio>,<Residual bit error
ratio>,<Delivery of erroneous
SDUs>,<Transfer delay>,<Traffic
handling priority>
[...]]
+CGEQNEG=? +CGEQNEG: (
list of
<cid>
s associated with active
contexts)
NOTE: The syntax of the AT Set Command is corrected to be according to ITU-T Recommendation V.250 [14]. Older
versions of the specification specify incorrect syntax +CGEQNEG=[<cid>[,<cid>[,...]]].
Description
This command allows the TE to retrieve the negotiated QoS profiles returned in the PDP context establishment
procedure.
The execution command returns the negotiated QoS profile for the specified context identifiers, <cid>s. The QoS
profile consists of a number of parameters, each of which may have a separate value.
If the parameter <cid> is omitted, the relevant information for all established PDP contexts are returned.
The test command returns a list of <cid>s associated with active contexts.
Defined values
<cid>: integer type; specifies a particular PDP context definition (see +CGDCONT and +CGDSCONT commands).
For the following parameters, see also 3GPP TS 23.107 [46].
<Traffic class>: integer type; indicates the type of application for which the UMTS bearer service is
optimised (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 conversational
1 streaming
2 interactive
3 background
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
232
3GPP TS 27.00
7 version 13.3.0 Release 13
<Maximum bitrate UL>: integer type; indicates the maximum number of kbits/s delivered to UMTS (up-link
traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' (e.g. +CGEQNEG:…,32, …)
(refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Maximum bitrate DL>: integer type; indicates the maximum number of kbits/s delivered by UMTS (down-
link traffic) at a SAP As an example a bitrate of 32kbit/s would be specified as '32' (e.g. +CGEQNEG:…,32, …)
(refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Guaranteed bitrate UL>: integer type; indicates the guaranteed number of kbits/s delivered to UMTS (up-
link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be
specified as '32' (e.g. +CGEQNEG:…,32, …) (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Guaranteed bitrate DL>: integer type; indicates the guaranteed number of kbits/s delivered by UMTS
(down-link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be
specified as '32' (e.g. +CGEQNEG:…,32, …) (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Delivery order>: integer type; indicates whether the UMTS bearer shall provide in-sequence SDU delivery
or not (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 no
1 yes
<Maximum SDU size>: integer type; (1,2,3,…) indicates the maximum allowed SDU size in octets (refer
3GPP TS 24.008 [8] subclause 10.5.6.5).
<SDU error ratio>: string type; indicates the target value for the fraction of SDUs lost or detected as
erroneous. SDU error ratio is defined only for conforming traffic. The value is specified as "mEe". As an
example a target SDU error ratio of 5•10
-3
would be specified as "5E3" (e.g. +CGEQNEG:…, "5E3",…) (refer
3GPP TS 24.008 [8] subclause 10.5.6.5).
<Residual bit error ratio>: string type; indicates the target value for the undetected bit error ratio in the
delivered SDUs. If no error detection is requested, Residual bit error ratio indicates the bit error ratio in the
delivered SDUs. The value is specified as "mEe". As an example a target residual bit error ratio of 5•10
-3
would
be specified as "5E3" (e.g. +CGEQNEG:…,"5E3",…) (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Delivery of erroneous SDUs>: integer type; indicates whether SDUs detected as erroneous shall be
delivered or not (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
0 no
1 yes
2 no detect
<Transfer delay>: integer type; (0,1,2,…) indicates the targeted time between request to transfer an SDU at
one SAP to its delivery at the other SAP, in milliseconds (refer 3GPP TS 24.008 [8] subclause 10.5.6.5).
<Traffic handling priority>: integer type; (1,2,3,…) specifies the relative importance for handling of all
SDUs belonging to the UMTS bearer compared to the SDUs of other bearers (refer 3GPP TS 24.008 [8]
subclause 10.5.6.5).
If a value is omitted for a particular class then the value is considered to be unspecified.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
233
3GPP TS 27.007 version 13.3.0 Release 13
10.1.9 PS attach or detach +CGATT
Table 119: +CGATT parameter command syntax
Command
Possible Response(s)
+CGATT=<state> +CM
E
ERROR: <err>
+CGATT? +CGATT: <state>
+CGATT=? +CGATT: (
list of supported
<state>
s
)
Description
The execution command is used to attach the MT to, or detach the MT from, the Packet Domain service. After the
command has completed, the MT remains in V.250 command state. If the MT is already in the requested state, the
command is ignored and the OK response is returned. If the requested state cannot be achieved, an ERROR or
+CME ERROR response is returned. Extended error responses are enabled by the +CMEE command. Refer
subclause 9.2 for possible <err> values.
NOTE 1: If the initial PDP context is supported, the context with <cid>=0 is automatically defined at startup, see
subclause 10.1.0.
Any active PDP contexts will be automatically deactivated when the attachment state changes to detached.
The read command returns the current Packet Domain service state.
The test command is used for requesting information on the supported Packet Domain service states.
NOTE 2: This command has the characteristics of both the V.250 action and parameter commands. Hence it has the
read form in addition to the execution/set and test forms.
Defined Values
<state>: integer type; indicates the state of PS attachment
0 detached
1 attached
Implementation
Optional.
10.1.10 PDP context activate or deactivate +CGACT
Table 120: +CGACT parameter command syntax
Command
Possible Response(s)
+CGACT=[<state>[,<cid>[,<cid>[,...]]]] +CM
E
ERROR: <err>
+CGACT? [+CGACT: <cid>,<state>]
[<CR><LF>+CGACT: <cid>,<state>
[...]]
+CGACT=? +CGACT: (
list of supported
<state>
s
)
Description
The execution command is used to activate or deactivate the specified PDP context (s). After the command has
completed, the MT remains in V.250 command state. If any PDP context is already in the requested state, the state for
that context remains unchanged. If the requested state for any specified context cannot be achieved, an ERROR or +CME
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
234
3GPP TS 27.007 version 13.3.0 Release 13
ERROR response is returned. Extended error responses are enabled by the +CMEE command. If the MT is not PS
attached when the activation form of the command is executed, the MT first performs a PS attach and then attempts to
activate the specified contexts. If the attach fails then the MT responds with ERROR or, if extended error responses are
enabled, with the appropriate failure-to-attach error message. Refer subclause 9.2 for possible <err> values.
For EPS, if an attempt is made to disconnect the last PDN connection, then the MT responds with ERROR or, if
extended error responses are enabled, a +CME ERROR.
NOTE: If the initial PDP context is supported, the context with <cid>=0 is automatically defined at startup, see
subclause 10.1.0.
For EPS, the activation request for an EPS bearer resource will be answered by the network by either an EPS dedicated
bearer activation or EPS bearer modification request. The request must be accepted by the MT before the PDP context
can be set in to established state.
If no <cid>s are specified the activation form of the command activates all defined non-emergency contexts.
If no <cid>s are specified the deactivation form of the command deactivates all active contexts.
The read command returns the current activation states for all the defined PDP contexts.
The test command is used for requesting information on the supported PDP context activation states.
NOTE. This command has the characteristics of both the V.250 action and parameter commands. Hence it has the
read form in addition to the execution/set and test forms.
Defined Values
<state>: integer type; indicates the state of PDP context activation. The default value is manufacturer specific.
0 deactivated
1 activated
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
Implementation
Optional.
10.1.11 PDP context modify +CGCMOD
Table 121: +CGCMOD action command syntax
Command
Possible Response(s)
+CGCMOD[=<cid>[,<cid>[,...]]] +CM
E
ERROR: <err>
+CGCMOD=? +CGCMOD: (
list of
<cid>
s associated with active
contexts)
NOTE: The syntax of the AT Set Command is corrected to be according to ITU-T Recommendation V.250 [14]. Older
versions of the specification specify incorrect syntax +CGCMOD=[<cid>[,<cid>[,...]]].
Description
The execution command is used to modify the specified PDP context (s) with repect to QoS profiles and TFTs. After
the command has completed, the MT returns to V.250 online data state. If the requested modification for any specified
context cannot be achieved, an ERROR or +CME ERROR response is returned. Extended error responses are enabled by
the +CMEE command. Refer subclause 9.2 for possible <err> values.
For EPS, the modification request for an EPS bearer resource will be answered by the network by an EPS bearer
modification request. The request must be accepted by the MT before the PDP context is effectively changed.
If no <cid>s are specified the activation form of the command modifies all active contexts.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
235
3GPP TS 27.007 version 13.3.0 Release 13
The test command returns a list of <cid>s associated with active contexts.
Defined Values
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
Implementation
Optional.
10.1.12 Enter data state +CGDATA
Table 122: +CGDATA action command syntax
Command
Possible Response(s)
+CGDATA[=<L2P>[,<cid>[,<cid>[,...]]]] CONNECT
ERROR
+CME ERROR: <err>
+CGDATA=? +CGDATA:
(
list of supported
<L2P>
s
)
NOTE: The syntax of the AT Set Command is corrected to be according to ITU-T Recommendation V.250 [14]. Older
versions of the specification specify incorrect syntax +CGDATA=[<L2P>[,<cid>[,<cid>[,...]]]].
Description
The execution command causes the MT to perform whatever actions are necessary to establish communication between
the TE and the network using one or more Packet Domain PDP types. This may include performing a PS attach and one
or more PDP context activations. If the <L2P> parameter value is unacceptable to the MT, the MT shall return an
ERROR or +CME ERROR response. Refer subclause 9.2 for possible <err> values. Otherwise, the MT issues the
intermediate result code CONNECT and enters V.250 online data state.
NOTE: If the initial PDP context is supported, the context with <cid>=0 is automatically defined at startup, see
subclause 10.1.0.
Commands following +CGDATA command in the AT command line shall not be processed by the MT.
The detailed behaviour after the online data state has been entered is dependent on the PDP type. It is described briefly
in 3GPP TS 27.060 [34] and in more detail in 3GPP TS 29.061 [39] and the specifications for the relevant PDPs. PS
attachment and PDP context activation procedures may take place prior to or during the PDP startup if they have not
already been performed using the +CGATT and +CGACT commands.
If context activation takes place during the PDP startup, one or more <cid>s may be specified in order to provide the
information needed for the context activation request(s).
During each PDP startup procedure the MT may have access to some or all of the following information -
The MT may have a priori knowledge, for example, it may implement only one PDP type.
The command may have provided an <L2P> parameter value.
The TE may provide a PDP type and/or PDP address to the MT during in the PDP startup procedure.
If any of this information is in conflict, the command will fail.
Any PDP type and/or PDP address present in the above information shall be compared with the PDP type and/or PDP
address in any context definitions specified in the command in the order in which their <cid>s appear. For a context
definition to match:
The PDP type must match exactly.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
236
3GPP TS 27.007 version 13.3.0 Release 13
The PDP addresses are considered to match if they are identical or if either or both addresses are unspecified.
For example, a PPP NCP request specifying PDP type = IP and no PDP address would cause the MT to search
through the specified context definitions for one with PDP type = IP and any PDP address.
The context shall be activated using the matched value for PDP type and a static PDP address if available, together with
the other information found in the PDP context definition. If a static PDP address is not available then a dynamic
address is requested.
If no <cid> is given or if there is no matching context definition, the MT shall attempt to activate the context with
whatever information is available to the MT. The other context parameters shall be set to their default values.
If the activation is successful, data transfer may proceed.
After data transfer is complete, and the layer 2 protocol termination procedure has completed successfully, the V.250
command state is re-entered and the MT returns the final result code OK.
In the event of an erroneous termination or a failure to start up, the V.250 command state is re-entered and the MT
returns the final result code NO CARRIER or, if enabled, +CME ERROR. Refer subclause 9.2 for possible <err>
values. Attach, activate and other errors may be reported.
The test command is used for requesting information on the supported layer 2 protocols.
This command may be used in both normal and modem compatibility modes.
Defined Values
<L2P>: string type; indicates the layer 2 protocol to be used between the TE and MT
NULL none, for PDP type OSP:IHOSS (Obsolete)
PPP Point-to-point protocol for a PDP such as IP
PAD character stream for X.25 character (triple X PAD) mode (Obsolete)
X25 X.25 L2 (LAPB) for X.25 packet mode (Obsolete)
M-xxxx manufacturer-specific protocol (xxxx is an alphanumeric string)
If the value is omitted, the layer 2 protocol is unspecified. Other values are reserved and will result in an ERROR
response.
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
Implementation
Optional if the D (dial) command can be used to specify Packet Domain operation.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
237
3GPP TS 27.007 versio
n 13.3.0 Release 13
10.1.13 Configure local octet stream PAD parameters +CGCLOSP
(Obsolete)
10.1.14 Show PDP address(es) +CGPADDR
Table 123: +CGPADDR action command syntax
Command
Possible respo
nse(s)
+CGPADDR[=<cid>[,<cid>
[,...]]] [+CGPADDR: <cid>[,<PDP_addr_1>[,<PDP_ad
dr_2>]]]
[<CR><LF>+CGPADDR: <cid>,[<PDP_addr_1>[
,<PDP_addr_2>]]
[...]]
+CGPADDR=? +CGPADDR: (list of defined <cid>s)
NOTE: The syntax of the AT Set Command is corrected to be according to
ITU-T Recommendation V.250 [14]. Older versions of the specification specify
incorrect syntax +CGPADDR=[,<cid>[,<cid>[,...]]].
Description
The execution command returns a list of PDP addresses for the specified context identifiers. If no <cid> is specified,
the addresses for all defined contexts are returned.
The test command returns a list of defined <cid>s.
Defined values
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
<PDP_addr_1> and <PDP_addr_2>: each is a string type that identifies the MT in the address space applicable
to the PDP. The address may be static or dynamic. For a static address, it will be the one set by the +CGDCONT
and +CGDSCONT commands when the context was defined. For a dynamic address it will be the one assigned
during the last PDP context activation that used the context definition referred to by <cid>. Both
<PDP_addr_1> and <PDP_addr_2>are omitted if none is available. Both <PDP_addr_1> and
<PDP_addr_2> are included when both IPv4 and IPv6 addresses are assigned, with <PDP_addr_1>
containing the IPv4 address and <PDP_addr_2> containing the IPv6 address.
The string is given as dot-separated numeric (0-255) parameter of the form:
a1.a2.a3.a4 for IPv4 and
a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16 for IPv6.
When +CGPIAF is supported, its settings can influence the format of the IPv6 address in parameter
<PDP_addr_1> or <PDP_addr_2> returned with the execute form of +CGPADDR.
NOTE: In dual-stack terminals (<PDP_type> IPV4V6), the IPv6 address will be provided in <PDP_addr_2>.
For terminals with a single IPv6 stack (<PDP_type> IPV6) or due to backwards compatibility, the IPv6
address can be provided in parameter <PDP_addr_1>.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
238
3GPP TS 27.007 version 13.3.0 Release 13
10.1.15 Automatic response to a network request for PDP context activation
+CGAUTO
Table 124: +CGAUTO parameter command syntax
Command
Possible response(s)
+CGAUTO=[<n>] +CME ERROR: <err>
+CGAUTO? +CGAUTO: <n>
+CGAUTO=? +CGAUTO: (list of supported <n>s)
Description
The set command disables or enables an automatic positive or negative response (auto-answer) to the receipt of a NW-
initiated Request PDP Context Activation message from the network in UMTS/GPRS and a NW-initiated Request EPS
Bearer Activation/ Modification Request messages in EPS. It also provides control over the use of the V.250 basic
commands 'S0', 'A' and 'H' for handling network requests for PDP context activation. The setting does not affect the
issuing of the unsolicited result code RING or +CRING.
When the +CGAUTO=0 command is received, the MT shall not perform a PS detach if it is attached. Subsequently,
when the MT announces a network request for PDP context activation by issuing the unsolicited result code RING or
+CRING, the TE may manually accept or reject the request by issuing the +CGANS command or may simply ignore the
network request.
When the +CGAUTO=1 command is received, the MT shall attempt to perform a PS attach if it is not already attached.
Failure will result in ERROR or, if enabled, +CME ERROR being returned to the TE. Refer subclause 9.2 for possible
<err> values. Subsequently, when the MT announces a network request for PDP context activation by issuing the
unsolicited result code RING or +CRING to the TE, this is followed by the intermediate result code CONNECT. The MT
then enters V.250 online data state and follows the same procedure as it would after having received a +CGANS=1 with
no <L2P> or <cid> values specified.
The read command returns the current value of <n>.
The test command returns the values of <n> supported by the MT as a compound value.
Defined values
<n>: integer type
0 turn off automatic response for Packet Domain only
1 turn on automatic response for Packet Domain only
2 modem compatibility mode, Packet Domain only
3 modem compatibility mode, Packet Domain and circuit switched calls
4 turn on automatic negative response for Packet Domain only
For <n> = 0 Packet Domain network requests are manually accepted or rejected by the +CGANS command.
For <n> = 1 Packet Domain network requests are automatically accepted according to the description above.
For <n> = 2, automatic acceptance of Packet Domain network requests is controlled by the 'S0' command. Manual
control uses the 'A' and 'H' commands, respectively, to accept and reject Packet Domain requests. (+CGANS may also be
used.) Incoming circuit switched calls can be neither manually nor automatically answered.
For <n> = 3, automatic acceptance of both Packet Domain network requests and incoming circuit switched calls is
controlled by the 'S0' command. Manual control uses the 'A' and 'H' commands, respectively, to accept and reject Packet
Domain requests. (+CGANS may also be used.) Circuit switched calls are handled as described elsewhere in this
specification.
For <n> = 4, Packet Domain network requests are automatically rejected.
ETSI
ETSI TS 1
27 007 V13.3.0 (2016
-
03)
239
3GPP TS 27.007 version 13.3.0 Release 13
Implementation
Optional. If not implemented, the MT shall behave according to the case of <n> = 3.
10.1.16 Manual response to a network request for PDP context activation
+CGANS
Table 125: +CGANS action command syntax
Command
Possible response(s)
+CGANS[=<response>,[<L2P>
,[<cid>]]] +CME ERROR: <err>
+CGANS=? +CGANS: (list of supported
<response>s),(list of supported <L2P>s)
NOTE: The syntax of the AT Set Command is corrected to be according to
ITU-T Recommendation V.250 [14]. Older versions of the specification specify
incorrect syntax +CGANS=[<response>,[<L2P>,[<cid>]]]
Description
The execution command requests the MT to respond to a network request for Packet Domain PDP context activation
which has been signalled to the TE by the RING, +CRING or +CGEV unsolicited result code. The <response>
parameter allows the TE to accept or reject the request.
If <response> is 0, the request is rejected and the MT returns OK to the TE.
If <response> is 1, the following procedure is followed by the MT.
Commands following the +CGANS command in the AT command line shall not be processed by the MT.
If the <L2P> parameter value is unacceptable to the MT, the MT shall return an ERROR or +CME ERROR response.
Refer subclause 9.2 for possible <err> values. Otherwise, the MT issues the intermediate result code CONNECT and
enters V.250 online data state.
The detailed behaviour after the online data state has been entered is dependent on the PDP type. It is described briefly
in 3GPP TS 27.060 [34] and in more detail in 3GPP TS 29.061 [39] and the specifications for the relevant PDPs. PDP
context activation procedures shall take place prior to or during the PDP startup.
One or more <cid>s may be specified in order to provide the values needed for the context activation request.
During the PDP startup procedure the MT has the PDP type and the PDP address provided by the network in the
Request PDP Context Activation message. The MT may also have some or all of the following information:
The MT may have a priori knowledge, for example, it may implement only one PDP type.
The command may have provided an <L2P> parameter value.
The TE may provide one or both of PDP type and PDP address to the MT in the PDP startup.
If any of this information is in conflict, the command will fail.
If one or more <cid> is given then an attempt shall be made to identify an appropriate context definition by matching
the PDP type and PDP address in the network request with the PDP type and PDP address in each of the specified
context definitions (in the order in which their <cid>s appear in the command) as follows:
The PDP type must match exactly.
The PDP addresses are considered to match if they are identical or if the address in the context definition is
unspecified.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
240
3GPP TS 27.007 version 13.3.0 Release 13
The context shall be activated using the values for PDP type and PDP address provided by the network, together with
the other information found in the PDP context definition. An APN may or may not re required, depending on the
application.
If no <cid> is given or if there is no matching context definition, the MT will attempt to activate the context using the
values for PDP type and PDP address provided by the network, together with any other relevant information known to
the MT. The other context parameters will be set to their default values.
If the activation is successful, data transfer may proceed.
After data transfer is complete, and the layer 2 protocol termination procedure has completed successfully, the V.250
command state is re-entered and the MT returns the final result code OK
In the event of an erroneous termination or a failure to startup, the V.250 command state is re-entered and the MT
returns the final result code NO CARRIER or, if enabled, +CME ERROR. Refer subclause 9.2 for possible <err>
values. Attach, activate and other errors may be reported. It is also an error to issue the +CGANS command when there
is no outstanding network request.
NOTE: This is not the same as if the MT issues a +CGDATA (or +CGACT) command after receiving a +CRING
unsolicited result code. A +CGDATA (or +CGACT) does not command the MT to acknowledge the
network request but rather to make a new request for context activation. The network request would be
ignored.
The test command returns the values of <response> and <L2P> supported by the MT as compound values.
This command may be used in both normal and modem compatibility modes.
Defined values
<response>: integer type; specifies how the request should be responded to.
0 reject the request
1 accept and request that the PDP context be activated
If <response> is omitted it is assumed to be 0.
<L2P>: string type; indicates the layer 2 protocol to be used (see +CGDATA command).
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
Implementation
Optional.
10.1.17 GPRS mobile station class +CGCLASS
Table 126: +CGCLASS parameter command syntax
Command
Possible Response(s)
+CGCLASS=[<class>] +CM
E
ERROR: <err>
+CGCLASS? +CGCLASS: <class>
+CGCLASS=? +CGCLASS: (
list of supported
<class>
s
)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
241
3GPP TS 27.007 version 13.3.0 Release 13
Description
The set command is used to set the MT to operate according to the specified mode of operation, see
3GPP TS 23.060 [47]. If the requested mode of operation is not supported, an ERROR or +CME ERROR response is
returned. Extended error responses are enabled by the +CMEE command. Refer subclause 9.2 for possible <err>
values.
The read command returns the mode of operation set by the TE, independent of the current serving cell capability and
independent of the current serving cell Access Technology. If no value has been set by the TE previously, the return
value shall be the highest mode of operation that can be supported by the MT.
The test command is used for requesting information on the supported MT modes of operation as a compound value.
Defined Values
<class>: string type; indicates the mode of operation. The default value is manufacturer specific.
A Class-A mode of operation (A/Gb mode), or CS/PS mode of operation (Iu mode) (highest mode of
operation)
B Class-B mode of operation (A/Gb mode), or CS/PS mode of operation (Iu mode)
CG Class-C mode of operation in PS only mode (A/Gb mode), or PS mode of operation (Iu mode)
CC Class-C mode of operation in CS only mode (A/Gb mode), or CS (Iu mode) (lowest mode of operation)
NOTE: <class> A means that the MT would operate simultaneous PS and CS service
<class> B means that the MT would operate PS and CS services but not simultaneously in A/Gb mode
<class> CG means that the MT would only operate PS services
<class> CC means that the MT would only operate CS services
If the MT is attached to the PS domain when the set command is issued with a <class> = CC specified, a PS detach
shall be performed by the MT.
Implementation
Optional.
10.1.18 Configure local triple-X PAD parameters +CGCLPAD (GPRS only)
(Obsolete)
10.1.19 Packet domain event reporting +CGEREP
Table 127: +CGEREP parameter command syntax
Command
Possible response(s)
+CGEREP=[<mode>[,<bfr>]] +CME ERROR: <err>
+CGEREP? +CGEREP: <mode>,<bfr>
+CGEREP=?
+CGEREP: (list of supported <mode>s),(list of supported
<bfr>s)
Description
Set command enables or disables sending of unsolicited result codes, +CGEV: XXX from MT to TE in the case of
certain events occurring in the Packet Domain MT or the network. <mode> controls the processing of unsolicited result
codes specified within this command. <bfr> controls the effect on buffered codes when <mode> 1 or 2 is entered. If a
setting is not supported by the MT, ERROR or +CME ERROR: is returned. Refer subclause 9.2 for possible <err>
values.
Read command returns the current mode and buffer settings
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
242
3GPP TS 27.007 version 13.3.0
Release 13
Test command returns the modes and buffer settings supported by the MT as compound values.
Defined values
<mode>: integer type
0 buffer unsolicited result codes in the MT; if MT result code buffer is full, the oldest ones can be discarded.
No codes are forwarded to the TE.
1 discard unsolicited result codes when MT-TE link is reserved (e.g. in on-line data mode); otherwise forward
them directly to the TE
2 buffer unsolicited result codes in the MT when MT-TE link is reserved (e.g. in on-line data mode) and flush
them to the TE when MT-TE link becomes available; otherwise forward them directly to the TE
<bfr>: integer type
0 MT buffer of unsolicited result codes defined within this command is cleared when <mode> 1 or 2 is entered
1 MT buffer of unsolicited result codes defined within this command is flushed to the TE when <mode> 1 or 2
is entered (OK response shall be given before flushing the codes)
Defined events
The events are valid for GPRS/UMTS and LTE unless explicitly mentioned.
For network attachment, the following unsolicited result codes and the corresponding events are defined:
+CGEV: NW DETACH
The network has forced a PS detach. This implies that all active contexts have been deactivated. These are not
reported separately.
+CGEV: ME DETACH
The mobile termination has forced a PS detach. This implies that all active contexts have been deactivated.
These are not reported separately.
For MT class, the following unsolicited result codes and the corresponding events are defined:
+CGEV: NW CLASS <class>
The network has forced a change of MT class. The highest available class is reported (see +CGCLASS). The
format of the parameter <class> is found in command +CGCLASS.
+CGEV: ME CLASS <class>
The mobile termination has forced a change of MT class. The highest available class is reported (see
+CGCLASS). The format of the parameter <class> is found in command +CGCLASS.
For PDP context activation, the following unsolicited result codes and the corresponding events are defined:
+CGEV: NW PDN ACT <cid>[,<WLAN_Offload>]
The network has activated a context. The context represents a Primary PDP context in GSM/UMTS. The <cid>
for this context is provided to the TE. The format of the parameter <cid> is found in command +CGDCONT.
<WLAN_Offload>: integer type. An integer that indicates whether traffic can be offloaded using the specified
PDN connection via a WLAN or not. This refers to bit 1 (E-UTRAN offload acceptability value) and bit 2
(UTRAN offload acceptability value) in the WLAN offload acceptability IE as specified in 3GPP TS 24.008 [8]
subclause 10.5.6.20.
0 offloading the traffic of the PDN connection via a WLAN when in S1 mode or when in Iu mode is not
acceptable.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
243
3GPP TS 27.007 version 13.3.0 Release 13
1 offloading the traffic of the PDN connection via a WLAN when in S1 mode is acceptable, but not acceptable
in Iu mode.
2 offloading the traffic of the PDN connection via a WLAN when in Iu mode is acceptable, but not acceptable
in S1 mode.
3 offloading the traffic of the PDN connection via a WLAN when in S1 mode or when in Iu mode is
acceptable.
NOTE 1: This event is not applicable for EPS.
+CGEV: ME PDN ACT <cid>[,<reason>[,<cid_other>]][,<WLAN_Offload>]
The mobile termination has activated a context. The context represents a PDN connection in LTE or a Primary
PDP context in GSM/UMTS. The <cid> for this context is provided to the TE. This event is sent either in result
of explicit context activation request (+CGACT), or in result of implicit context activation request associated to
attach request (+CGATT=1). The format of the parameters <cid> and <cid_other> are found in command
+CGDCONT. The format of the parameter <WLAN_Offload> is defined above.
<reason>: integer type; indicates the reason why the context activation request for PDP type IPv4v6 was not
granted. This parameter is only included if the requested PDP type associated with <cid> is IPv4v6, and the
PDP type assigned by the network for <cid> is either IPv4 or IPv6.
0 IPv4 only allowed
1 IPv6 only allowed
2 single address bearers only allowed.
3 single address bearers only allowed and MT initiated context activation for a second address type bearer was
not successful.
<cid_other>: integer type; indicates the context identifier allocated by MT for an MT initiated context of a
second address type. MT shall only include this parameter if <reason> parameter indicates single address
bearers only allowed, and MT supports MT initiated context activation of a second address type without
additional commands from TE, and MT has activated the PDN connection or PDP context associated with
<cid_other>.
NOTE 1A: For legacy TEs supporting MT initiated context activation without TE requests, there is also a
subsequent event +CGEV: ME PDN ACT <cid_other> returned to TE.
+CGEV: NW ACT <p_cid>, <cid>, <event_type>[,<WLAN_Offload>]
The network has activated a context. The <cid> for this context is provided to the TE in addition to the
associated primary <p_cid>. The format of the parameters <p_cid> and <cid> are found in command
+CGDSCONT. The format of the parameter <WLAN_Offload> is defined above.
<event_type>: integer type; indicates whether this is an informational event or whether the TE has to
acknowledge it.
0 Informational event
1 Information request: Acknowledgement required. The acknowledgement can be accept or reject, see
+CGANS.
+CGEV: ME ACT <p_cid>, <cid>, <event_type>[,<WLAN_Offload>]
The network has responded to an ME initiated context activation. The <cid> for this context is provided to the
TE in addition to the associated primary <p_cid>. The format of the parameters <p_cid> and <cid> are
found in command +CGDSCONT. The format of the parameters <event_type> and <WLAN_Offload> are
defined above.
13
ETSI
ETSI TS 127 007 V
13.3.0 (2016
-
03)
244
3GPP TS 27.007 version 13.3.0 Release 13
For PDP context deactivation, the following unsolicited result codes and the corresponding events are defined:
+CGEV: NW DEACT <PDP_type>, <PDP_addr>, [<cid>]
The network has forced a context deactivation. The <cid> that was used to activate the context is provided if
known to the MT. The format of the parameters <PDP_type>, <PDP_addr> and <cid> are found in
command +CGDCONT.
+CGEV: ME DEACT <PDP_type>, <PDP_addr>, [<cid>]
The mobile termination has forced a context deactivation. The <cid> that was used to activate the context is
provided if known to the MT. The format of the parameters <PDP_type>, <PDP_addr> and <cid> are
found in command +CGDCONT.
+CGEV: NW PDN DEACT <cid>[,<WLAN_Offload>]
The network has deactivated a context. The context represents a PDN connection in LTE or a Primary PDP context
in GSM/UMTS. The associated <cid> for this context is provided to the TE. The format of the parameter <cid> is
found in command +CGDCONT. The format of the parameter <WLAN_Offload> is defined above.
NOTE 2: Occurrence of this event replaces usage of the event
+CGEV: NW DEACT <PDP_type>, <PDP_addr>, [<cid>].
+CGEV: ME PDN DEACT <cid>
The mobile termination has deactivated a context. The context represents a PDN connection in LTE or a Primary
PDP context in GSM/UMTS. The <cid> for this context is provided to the TE. The format of the parameter
<cid> is found in command +CGDCONT.
NOTE 3: Occurrence of this event replaces usage of the event
+CGEV: ME DEACT <PDP_type>, <PDP_addr>, [<cid>].
+CGEV: NW DEACT <p_cid>, <cid>, <event_type>[,<WLAN_Offload>]
The network has deactivated a context. The <cid> for this context is provided to the TE in addition to the
associated primary <p_cid>. The format of the parameters <p_cid> and <cid> are found in command
+CGDSCONT. The format of the parameters <event_type> and <WLAN_Offload> are defined above.
NOTE 4: Occurrence of this event replaces usage of the event
+CGEV: NW DEACT <PDP_type>, <PDP_addr>, [<cid>].
+CGEV: ME DEACT <p_cid>, <cid>, <event_type>
The network has responded to an ME initiated context deactivation request. The associated <cid> is provided
to the TE in addition to the associated primary <p_cid>. The format of the parameters <p_cid> and <cid>
are found in command +CGDSCONT. The format of the parameter <event_type> is defined above.
NOTE 5: Occurrence of this event replaces usage of the event
+CGEV: ME DEACT <PDP_type>, <PDP_addr>, [<cid>].
For PDP context modification, the following unsolicited result codes and the corresponding events are defined:
+CGEV: NW MODIFY <cid>, <change_reason>, <event_type>[,<WLAN_Offload>]
The network has modified a context. The associated <cid> is provided to the TE in addition to the
<change_reason> and <event_type>. The format of the parameter <cid> is found in command
+CGDCONT or +CGDSCONT. The format of the parameters <change_reason>, <event_type>, and
<WLAN_Offload> are defined above.
<change_reason>: integer type; a bitmap that indicates what kind of change occurred. The
<change_reason> value is determined by summing all the applicable bits. For example if both the values of
QoS changed (Bit 2) and WLAN_Offload changed (Bit 3) have changed, then the <change_reason> value is
6.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
245
3GPP TS 27.007 version 13.3.0 Release 13
NOTE 5A: The WLAN offload value will change when bit 1 or bit 2 or both of the indicators in the WLAN
offload acceptability IE change, see the parameter <WLAN_Offload> defined above.
Bit 1 TFT changed
Bit 2 Qos changed
Bit 3 WLAN Offload changed
+CGEV: ME MODIFY <cid>, <change_reason>, <event_type>[,<WLAN_Offload>]
The mobile termination has modified a context. The associated <cid> is provided to the TE in addition to the
<change_reason> and <event_type>. The format of the parameter <cid> is found in command
+CGDCONT or +CGDSCONT. The format of the parameters <change_reason>, <event_type> and
<WLAN_Offload> are defined above.
For other PDP context handling, the following unsolicited result codes and the corresponding events are defined:
+CGEV: REJECT <PDP_type>, <PDP_addr>
A network request for context activation occurred when the MT was unable to report it to the TE with a +CRING
unsolicited result code and was automatically rejected. The format of the parameters <PDP_type> and
<PDP_addr> are found in command +CGDCONT.
NOTE 6: This event is not applicable for EPS.
+CGEV: NW REACT <PDP_type>, <PDP_addr>, [<cid>]
The network has requested a context reactivation. The <cid> that was used to reactivate the context is provided
if known to the MT. The format of the parameters <PDP_type>, <PDP_addr> and <cid> are found in
command +CGDCONT.
NOTE 7: This event is not applicable for EPS.
Implementation
Optional.
10.1.20 GPRS network registration status +CGREG
Table 128: +CGREG parameter command syntax
Command
Possible response(s)
+CGREG=[<n>] +CME ERROR: <err>
+CGREG? when <n>=0, 1, 2 or 3 and command successful:
+CGREG: <n>,<stat>[,[<lac>],[<ci>],[<AcT>],[
<rac>][,<cause_type>,<reject_cause>]]
when <n>=4 or 5 and command successful:
+CGREG: <n>,<stat>[,[<lac>],[<ci>],[<AcT>],[
<rac>][,[<cause_type>],[<reject_cause>][,[<A
ctive-Time>],[<Periodic-RAU>],[<GPRS-READY-
timer>]]]]
+CGREG=? +CGREG: (list of supported <n>s)
Description
The set command controls the presentation of an unsolicited result code +CGREG: <stat> when <n>=1 and there is
a change in the MT's GPRS network registration status in GERAN/UTRAN, or unsolicited result code
+CGREG: <stat>[,[<lac>],[<ci>],[<AcT>],[<rac>]] when <n>=2 and there is a change of the
network cell in GERAN/UTRAN. The parameters <AcT>, <lac>, <rac> and <ci> are provided only if available.
The value <n>=3 further extends the unsolicited result code with [,<cause_type>,<reject_cause>], when
available, when the value of <stat> changes.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
246
3GPP TS 27.007 version 13.3.0 Release 13
If the UE wants to apply PSM for reducing its power consumption, see +CPSMS command and 3GPP TS 23.682 [149],
the set command controls the presentation of an unsolicited result code
+CGREG: <stat>[,[<lac>],[<ci>],[<AcT>],[<rac>][,[<cause_type>],[<reject_cause>][
,[<Active-Time>],[<Periodic-RAU>],[<GPRS-READY-timer>]]]]. When <n>=4 the unsolicited
result code will provide the UE with additional information for the Active Time value, the extended periodic RAU
value and the GPRS READY timer value if there is a change of the network cell in GERAN/UTRAN. The value <n>=5
further enhances the unsolicited result code with <cause_type> and <reject_cause> when the value of
<stat> changes. The parameters <AcT>, <lac>, <rac>, <ci>, <cause_type>, <reject_cause>,
<Active-Time>, <Periodic-RAU> and <GPRS-READY-timer> are provided only if available.
Refer subclause 9.2 for possible <err> values.
NOTE 1: If the GPRS MT also supports circuit mode services in GERAN/UTRAN and/or EPS services in E-
UTRAN, the +CREG command and +CREG: result codes and/or the +CEREG command and +CEREG:
result codes apply to the registration status and location information for those services.
The read command returns the status of result code presentation and an integer <stat> which shows whether the
network has currently indicated the registration of the MT. Location information elements <lac>, <ci>, <AcT> and
<rac>, if available, are returned only when <n>=2 and MT is registered in the network. The parameters
[,<cause_type>,<reject_cause>], if available, are returned when <n>=3.
Test command returns values supported as a compound value.
Defined values
<n>: integer type
0 disable network registration unsolicited result code
1 enable network registration unsolicited result code +CGREG: <stat>
2 enable network registration and location information unsolicited result code
+CGREG: <stat>[,<[lac>,]<[ci>],[<AcT>],[<rac>]]
3 enable network registration, location information and GMM cause value information unsolicited result code
+CGREG: <stat>[,[<lac>],[<ci>],[<AcT>],[<rac>][,<cause_type>,<reject_caus
e>]]
4 For a UE that wants to apply PSM, enable network registration and location information unsolicited result
code +CGREG: <stat>[,[<lac>],[<ci>],[<AcT>],[<rac>][,,[,[<Active-
Time>],[<Periodic-RAU>],[<GPRS-READY-timer>]]]]
5 For a UE that wants to apply PSM, enable network registration, location information and GMM cause value
information unsolicited result code
+CGREG: <stat>[,[<lac>],[<ci>],[<AcT>],[<rac>][,[<cause_type>],[<reject_c
ause>][,[<Active-Time>],[<Periodic-RAU>],[<GPRS-READY-timer>]]]]
<stat>: integer type; indicates the GPRS registration status
0 not registered, MT is not currently searching an operator to register to
1 registered, home network
2 not registered, but MT is currently trying to attach or searching an operator to register to
3 registration denied
4 unknown (e.g. out of GERAN/UTRAN coverage)
5 registered, roaming
6 registered for "SMS only", home network (not applicable)
7 registered for "SMS only", roaming (not applicable)
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
247
3GPP TS 27.007 version 13.3.0 Release
13
8 attached for emergency bearer services only (see NOTE 2) (applicable only when <AcT> indicates 2,4,5,6)
9 registered for "CSFB not preferred", home network (not applicable)
10 registered for "CSFB not preferred", roaming (not applicable)
NOTE 2: 3GPP TS 24.008 [8] and 3GPP TS 24.301 [83] specify the condition when the MS is considered as
attached for emergency bearer services.
<lac>: string type; two byte location area code in hexadecimal format (e.g. "00C3" equals 195 in decimal)
<ci>: string type; four byte GERAN/UTRAN cell ID in hexadecimal format
<AcT>: integer type; indicates the access technology of the serving cell
0 GSM
1 GSM Compact
2 UTRAN
3 GSM w/EGPRS (see NOTE 3)
4 UTRAN w/HSDPA (see NOTE 4)
5 UTRAN w/HSUPA (see NOTE 4)
6 UTRAN w/HSDPA and HSUPA (see NOTE 4)
7 E-UTRAN (not applicable)
NOTE 3: 3GPP TS 44.060 [71] specifies the System Information messages which give the information about
whether the serving cell supports EGPRS.
NOTE 4: 3GPP TS 25.331 [74] specifies the System Information blocks which give the information about whether
the serving cell supports HSDPA or HSUPA.
<rac>: string type; one byte routing area code in hexadecimal format
<cause_type>: integer type; indicates the type of <reject_cause>.
0 Indicates that <reject_cause> contains a GMM cause value, see 3GPP TS 24.008 [8] Annex G.
1 Indicates that <reject_cause> contains a manufacturer-specific cause.
<reject_cause>: integer type; contains the cause of the failed registration. The value is of type as defined by
<cause_type>.
<Active-Time>: string type; one byte in an 8 bit format. Indicates the Active Time value (T3324) allocated to
the UE in GERAN/UTRAN. The Active Time value is coded as one byte (octet 3) of the GPRS Timer 2
information element coded as bit format (e.g. "00100100" equals 4 minutes). For the coding and the value range,
see the GPRS Timer 2 IE in 3GPP TS 24.008 [8] Table 10.5.163/3GPP TS 24.008. See also
3GPP TS 23.682 [149] and 3GPP TS 23.060 [47].
<Periodic-RAU>: string type; one byte in an 8 bit format. Indicates the extended periodic RAU value (T3312)
allocated to the UE in GERAN/UTRAN. The extended periodic RAU value s coded as one byte (octet 3) of the
GPRS Timer 3 information element coded as bit format (e.g. "01000111" equals 70 hours). For the coding and
the value range, see the GPRS Timer 3 IE in 3GPP TS 24.008 [8] Table 10.5.163a/3GPP TS 24.008. See also
3GPP TS 23.682 [149] and 3GPP TS 23.060 [47].
<GPRS-READY-timer>: string type; one byte in an 8 bit format. Indicates the GPRS READY timer value
(T3314) allocated to the UE in GERAN/UTRAN. The GPRS READY timer value is coded as one byte (octet 2)
of the GPRS Timer information element coded as bit format (e.g. "01000011" equals 3 decihours or 18 minutes).
For the coding and the value range, see the GPRS Timer IE in 3GPP TS 24.008 [8]
Table 10.5.172/3GPP TS 24.008. See also 3GPP TS 23.060 [47].
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
248
3GPP TS 27.007 version 13.3.0 Release 13
Implementation
Optional.
10.1.21 Select service for MO SMS messages +CGSMS
Table 129: +CGSMS parameter command syntax
Command
Possible Response(s)
+CGSMS=[<service>]
+CGSMS? +CGSMS: <service>
+CGSMS=? +CGSMS: (
list of currently available
<service>
s
)
Description
The set command is used to specify the service or service preference that the MT will use to send MO SMS messages.
The read command returns the currently selected service or service preference.
The test command is used for requesting information on the currently available services and service preferences as a
compound value.
Defined Values
<service>: integer type; indicates the service or service preference to be used. The default value is manufacturer
specific.
0 Packet Domain
1 circuit switched
2 Packet Domain preferred (use circuit switched if GPRS not available)
3 circuit switched preferred (use Packet Domain if circuit switched not available)
Implementation
Optional.
10.1.22 EPS network registration status +CEREG
Table 10.1.22-1: +CEREG parameter command syntax
Command
Possible response(s)
+CEREG=[<n>] +CME ERROR: <err>
+CEREG? when <n>=0, 1, 2 or 3 and command successful:
+CEREG: <n>,<stat>[,[<tac>],[<ci>],[<AcT>[,
<cause_type>,<reject_cause>]]]
when <n>=4 or 5 and command successful:
+CEREG: <n>,<stat>[,[<lac>],[<ci>],[<AcT>],
[<rac>][,[<cause_type>],[<reject_cause>][,[
<Active-Time>],[<Periodic-TAU>]]]]
+CEREG=? +CEREG: (list of supported <n>s)
Description
The set command controls the presentation of an unsolicited result code +CEREG: <stat> when <n>=1 and there is
a change in the MT's EPS network registration status in E-UTRAN, or unsolicited result code
+CEREG: <stat>[,[<tac>],[<ci>],[<AcT>]] when <n>=2 and there is a change of the network cell in E-
ETSI
ETSI TS 127 007 V13.3.0 (
2016
-
03)
249
3GPP TS 27.007 version 13.3.0 Release 13
UTRAN. The parameters <AcT>, <tac> and <ci> are provided only if available.The value <n>=3 further extends
the unsolicited result code with [,<cause_type>,<reject_cause>], when available, when the value of
<stat> changes.
If the UE wants to apply PSM for reducing its power consumption, see +CPSMS command and 3GPP TS 23.682 [149],
the set command controls the presentation of an unsolicited result
code+CEREG: <stat>[,[<tac>],[<ci>],[<AcT>][,[<cause_type>],[<reject_cause>][,[<Ac
tive-Time>],[<Periodic-TAU>]]]]. When <n>=4 the unsolicited result code will provide the UE with
additional information for the Active Time value and the extended periodic TAU value if there is a change of the
network cell in E-UTRAN. The value <n>=5 further enhances the unsolicited result code with <cause_type> and
<reject_cause> when the value of <stat> changes. The parameters <AcT>, <tac>, <ci>, <cause_type>,
<reject_cause>, <Active-Time> and <Periodic-TAU> are provided only if available.
Refer subclause 9.2 for possible <err> values.
NOTE 1: If the EPS MT in GERAN/UTRAN/E-UTRAN also supports circuit mode services and/or GPRS services,
the +CREG command and +CREG: result codes and/or the +CGREG command and +CGREG: result
codes apply to the registration status and location information for those services.
The read command returns the status of result code presentation and an integer <stat> which shows whether the
network has currently indicated the registration of the MT. Location information elements <tac>, <ci> and <AcT>,
if available, are returned only when <n>=2 and MT is registered in the network. The parameters
[,<cause_type>,<reject_cause>], if available, are returned when <n>=3.
Test command returns values supported as a compound value.
Defined values
<n>: integer type
0 disable network registration unsolicited result code
1 enable network registration unsolicited result code +CEREG: <stat>
2 enable network registration and location information unsolicited result code
+CEREG: <stat>[,[<tac>],[<ci>],[<AcT>]]
3 enable network registration, location information and EMM cause value information unsolicited result code
+CEREG: <stat>[,[<tac>],[<ci>],[<AcT>][,<cause_type>,<reject_cause>]]
4 For a UE that wants to apply PSM, enable network registration and location information unsolicited result
code +CEREG: <stat>[,[<tac>],[<ci>],[<AcT>][,,[,[<Active-
Time>],[<Periodic-TAU>]]]]
5 For a UE that wants to apply PSM, enable network registration, location information and EMM cause value
information unsolicited result code
+CEREG: <stat>[,[<tac>],[<ci>],[<AcT>][,[<cause_type>],[<reject_cause>][,
[<Active-Time>],[<Periodic-TAU>]]]]
<stat>: integer type; indicates the EPS registration status
0 not registered, MT is not currently searching an operator to register to
1 registered, home network
2 not registered, but MT is currently trying to attach or searching an operator to register to
3 registration denied
4 unknown (e.g. out of E-UTRAN coverage)
5 registered, roaming
6 registered for "SMS only", home network (not applicable)
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
250
3GPP TS 27.007 version 13.3.0 Release 13
7 registered for "SMS only", roaming (not applicable)
8 attached for emergency bearer services only (See NOTE 2)
9 registered for "CSFB not preferred", home network (not applicable)
10 registered for "CSFB not preferred", roaming (not applicable)
NOTE 2: 3GPP TS 24.008 [8] and 3GPP TS 24.301 [83] specify the condition when the MS is considered as
attached for emergency bearer services.
<tac>: string type; two byte tracking area code in hexadecimal format (e.g. "00C3" equals 195 in decimal)
<ci>: string type; four byte E-UTRAN cell ID in hexadecimal format
<AcT>: integer type; indicates the access technology of the serving cell
0 GSM (not applicable)
1 GSM Compact (not applicable)
2 UTRAN (not applicable)
3 GSM w/EGPRS (see NOTE 3) (not applicable)
4 UTRAN w/HSDPA (see NOTE 4) (not applicable)
5 UTRAN w/HSUPA (see NOTE 4) (not applicable)
6 UTRAN w/HSDPA and HSUPA (see NOTE 4) (not applicable)
7 E-UTRAN
NOTE 3: 3GPP TS 44.060 [71] specifies the System Information messages which give the information about
whether the serving cell supports EGPRS.
NOTE 4: 3GPP TS 25.331 [74] specifies the System Information blocks which give the information about whether
the serving cell supports HSDPA or HSUPA.
<cause_type>: integer type; indicates the type of <reject_cause>.
0 Indicates that <reject_cause> contains an EMM cause value, see 3GPP TS 24.301 [83] Annex A.
1 Indicates that <reject_cause> contains a manufacturer-specific cause.
<reject_cause>: integer type; contains the cause of the failed registration. The value is of type as defined by
<cause_type>.
<Active-Time>: string type; one byte in an 8 bit format. Indicates the Active Time value (T3324) allocated to
the UE in E-UTRAN. The Active Time value is coded as one byte (octet 3) of the GPRS Timer 2 information
element coded as bit format (e.g. "00100100" equals 4 minutes). For the coding and the value range, see the
GPRS Timer 2 IE in 3GPP TS 24.008 [8] Table 10.5.163/3GPP TS 24.008. See also 3GPP TS 23.682 [149] and
3GPP TS 23.401 [82].
<Periodic-TAU>: string type; one byte in an 8 bit format. Indicates the extended periodic TAU value (T3412)
allocated to the UE in E-UTRAN. The extended periodic TAU value is coded as one byte (octet 3) of the GPRS
Timer 3 information element coded as bit format (e.g. "01000111" equals 70 hours). For the coding and the
value range, see the GPRS Timer 3 IE in 3GPP TS 24.008 [8] Table 10.5.163a/3GPP TS 24.008. See also
3GPP TS 23.682 [149] and 3GPP TS 23.401 [82].
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
251
3GPP TS 27.007 version 13.3.0 Release 13
10.1.23 PDP context read dynamic parameters +CGCONTRDP
Table 10.1.23-1: +CGCONTRDP action command syntax
Command
Possible response(s)
+CGCONTRDP[=<cid>] [+CGCONTRDP: <cid>,<bearer_id>,<apn>[,<l
ocal_addr and
subnet_mask>[,<gw_addr>[,<DNS_prim_addr>
[,<DNS_sec_addr>[,<P-
CSCF_prim_addr>[,<P-
CSCF_sec_addr>[,<IM_CN_Signalling_Flag>[
,<LIPA_indication>[,<IPv4_MTU>[,<WLAN_Of
fload>[,<Local_Addr_Ind>]]]]]]]]]]]]
[<CR><LF>+CGCONTRDP: <cid>,<bearer_id>,<
apn>[,<local_addr and subnet_mask>
[,<gw_addr>[,<DNS_prim_addr>[,<DNS_sec_a
ddr>[,<P-CSCF_prim_addr>[,<P-
CSCF_sec_addr>[,<IM_CN_Signalling_Flag>[
,<LIPA_indication>[,<IPv4_MTU>[,<WLAN_Of
fload>[,<Local_Addr_Ind>]]]]]]]]]]]
[...]]
+CGCONTRDP=? +CGCONTRDP: (list of <cid>s associated with active
contexts)
NOTE: The syntax of the AT Set Command is corrected to be according to
ITU-T Recommendation V.250 [14]. Older versions of the specification specify incorrect
syntax +CGCONTRDP=[<cid>]
Description
The execution command returns the relevant information <bearer_id>, <apn>, <local_addr and
subnet_mask>, <gw_addr>, <DNS_prim_addr>, <DNS_sec_addr>, <P-CSCF_prim_addr>, <P-
CSCF_sec_addr>, <IM_CN_Signalling_Flag>, <LIPA_indication>, <IPv4_MTU> and
<WLAN_Offload> for an active non secondary PDP context with the context identifier <cid>.
If the MT indicates more than two IP addresses of P-CSCF servers or more than two IP addresses of DNS servers,
multiple lines of information per <cid> will be returned.
If the MT has dual stack capabilities, at least one pair of lines with information is returned per <cid>. First one line
with the IPv4 parameters followed by one line with the IPv6 parameters. If this MT with dual stack capabilities
indicates more than two IP addresses of P-CSCF servers or more than two IP addresses of DNS servers, multiple of
such pairs of lines are returned.
NOTE: If the MT doesn't have all the IP addresses to be included in a line, e.g. in case the UE received four IP
addresses of DNS servers and two IP addresses of P-CSCF servers, the parameter value representing an
IP address that can not be populated is set to an empty string or an absent string.
If the parameter <cid> is omitted, the relevant information for all active non secondary PDP contexts is returned.
The test command returns a list of <cid>s associated with active non secondary contexts.
Defined values
<cid>: integer type; specifies a particular non secondary PDP context definition. The parameter is local to the TE-
MT interface and is used in other PDP context-related commands (see the +CGDCONT and +CGDSCONT
commands).
<bearer_id>: integer type; identifies the bearer, i.e. the EPS bearer in EPS and the NSAPI in UMTS/GPRS.
<apn>: string type; a logical name that was used to select the GGSN or the external packet data network.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
252
3GPP TS 27.007 version 13.3.0 Release 13
<local_addr and subnet_mask>: string type; shows the IP address and subnet mask of the MT. The string
is given as dot-separated numeric (0-255) parameters on the form:
"a1.a2.a3.a4.m1.m2.m3.m4" for IPv4 or
"a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16.m1.m2.m3.m4.m5.m6.m7.m8.m9.m10.m11.m12.m13.
m14.m15.m16" for IPv6.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the execute
form of +CGCONTRDP.
<gw_addr>: string type; shows the Gateway Address of the MT. The string is given as dot-separated numeric (0-
255) parameters.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the execute
form of +CGCONTRDP.
<DNS_prim_addr>: string type; shows the IP address of the primary DNS server.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the execute
form of +CGCONTRDP.
<DNS_sec_addr>: string type; shows the IP address of the secondary DNS server.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the execute
form of +CGCONTRDP.
<P_CSCF_prim_addr>: string type; shows the IP address of the primary P-CSCF server.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the execute
form of +CGCONTRDP.
<P_CSCF_sec_addr>: string type; shows the IP address of the secondary P-CSCF server.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the execute
form of +CGCONTRDP.
<IM_CN_Signalling_Flag>: integer type; shows whether the PDP context is for IM CN subsystem-related
signalling only or not.
0 PDP context is not for IM CN subsystem-related signalling only
1 PDP context is for IM CN subsystem-related signalling only
<LIPA_indication>: integer type; indicates that the PDP context provides connectivity using a LIPA PDN
connection. This parameter cannot be set by the TE.
0 indication not received that the PDP context provides connectivity using a LIPA PDN connection
1 indication received that the PDP context provides connectivity using a LIPA PDN connection
<IPv4_MTU>: integer type; shows the IPv4 MTU size in octets.
<WLAN_Offload>: integer type. An integer that indicates whether traffic can be offloaded using the specified
PDN connection via a WLAN or not. This refers to bits 1 and 2 of the WLAN offload acceptability IE as
specified in 3GPP TS 24.008 [8] subclause 10.5.6.20.
0 offloading the traffic of the PDN connection via a WLAN when in S1 mode or when in Iu mode is not
acceptable.
1 offloading the traffic of the PDN connection via a WLAN when in S1 mode is acceptable, but not acceptable
in Iu mode.
2 offloading the traffic of the PDN connection via a WLAN when in Iu mode is acceptable, but not acceptable
in S1 mode.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
253
3GPP TS 27.007 version 13.3.0 Release 13
3 offloading the traffic of the PDN connection via a WLAN when in S1 mode or when in Iu mode is
acceptable.
<Local_Addr_Ind>: integer type; indicates to the network whether or not the MS supports local IP address in
TFTs (see 3GPP TS 24.301 [83] and 3GPP TS 24.008 [8] subclause 10.5.6.3).
0 indicates that the MS supports local IP address in TFTs
1 indicates that the MS does not support local IP address in TFTs
Implementation
Optional.
10.1.24 Secondary PDP context read dynamic parameters +CGSCONTRDP
Table 10.1.24-1: +CGSCONTRDP action command syntax
Command
Possible response(s)
+CGSCONTRDP[=<cid>] [+CGSCONTRDP: <cid>,<p_cid>,<bearer_id>[,<IM_CN_
Signalling_Flag>[,<WLAN_Offload>]]]
[<CR><LF>+CGSCONTRDP: <cid>,<p_cid>,<bearer_id>[
,<IM_CN_Signalling_Flag>[,<WLAN_Offload>]]
[...]]
+CGSCONTRDP=? +CGSCONTRDP: (list of <cid>s associated with active contexts)
NOTE: The syntax of the AT Set Command is corrected to be according to
ITU-T Recommendation V.250 [14]. Older versions of the specification specify incorrect syntax
+CGSCONTRDP=[<cid>]
Description
The execution command returns <p_cid>, <bearer_id>, <IM_CN_Signalling_Flag> and
<WLAN_Offload> for an active secondary PDP context with the context identifier <cid>.
If the parameter <cid> is omitted, the <cid>, <p_cid>, <bearer_id> and <IM_CN_Signalling_Flag> are
returned for all active secondary PDP contexts.
In EPS, the Traffic Flow parameters are returned.
NOTE: Parameters for UE initiated and network initiated PDP contexts are returned.
The test command returns a list of <cid>s associated with active secondary PDP contexts.
Defined values
<cid>: integer type; specifies a particular active secondary PDP context or Traffic Flows definition. The parameter
is local to the TE-MT interface and is used in other PDP context-related commands (see the +CGDCONT and
+CGDSCONT commands).
<p_cid>: integer type; specifies a particular PDP context definition or default EPS context Identifier which has
been specified by use of the +CGDCONT command. The parameter is local to the TE-MT interface (see the
+CGDSCONT command).
<bearer_id>: integer type; identifies the bearer, EPS Bearer in EPS and NSAPI in UMTS/GPRS.
<IM_CN_Signalling_Flag>: integer type; shows whether the PDP context is for IM CN subsystem-related
signalling only or not.
0 PDP context is not for IM CN subsystem-related signalling only
1 PDP context is for IM CN subsystem-related signalling only
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
254
3GPP TS 27.007 version 13.3.0 Release 13
<WLAN_Offload>: integer type. An integer that indicates whether traffic can be offloaded using the specified
PDN connection via a WLAN or not. This refers to bits 1 and 2 of the WLAN offload acceptability IE as
specified in 3GPP TS 24.008 [8] subclause 10.5.6.20.
0 offloading the traffic of the PDN connection via a WLAN when in S1 mode or when in Iu mode is not
acceptable.
1 offloading the traffic of the PDN connection via a WLAN when in S1 mode is acceptable, but not acceptable
in Iu mode.
2 offloading the traffic of the PDN connection via a WLAN when in Iu mode is acceptable, but not acceptable
in S1 mode.
3 offloading the traffic of the PDN connection via a WLAN when in S1 mode or when in Iu mode is
acceptable.
Implementation
Optional.
10.1.25 Traffic flow template read dynamic parameters +CGTFTRDP
Table 10.1.25-1: +CGTFTRDP action command syntax
Command
Possible Response(s)
+CGTFTRDP[=<cid>] [+CGTFTRDP: <cid>,<packet filter
identifier>,<evaluation precedence index>,<remote
address and subnet mask>,<protocol number (ipv4) /
next header (ipv6)>,<local port range>,<remote
port range>,<ipsec security parameter index
(spi)>,<type of service (tos) (ipv4) and mask /
traffic class (ipv6) and mask>,<flow label
(ipv6)>,<direction>,<NW packet filter
Identifier>,<local address and subnet mask>]
[<CR><LF>+CGTFTRDP: <cid>,<packet filter
identifier>,<evaluation precedence index>,<remote
address and subnet mask>,<protocol number (ipv4) /
next header (ipv6)>,<local port range>, <remote
port range>,<ipsec security parameter index
(spi)>,<type of service (tos) (ipv4) and mask /
traffic class (ipv6) and mask>,<flow label
(ipv6)>,<direction>,<NW packet filter
Identifier>,<local address and subnetmask>
[...]]
+CGTFTRDP=? +CGTFTRDP: (list of <cid>s associated with active contexts)
NOTE: The syntax of the AT Set Command is corrected to be according to
ITU-T Recommendation V.250 [14]. Older versions of the specification specify incorrect syntax
+CGTFTRDP=[<cid>]
Description
The execution command returns the relevant information about Traffic Flow Template for an active secondary or non
secondary PDP context specified by <cid> together with the additional network assigned values when established by
the network. If the parameter <cid> is omitted, the Traffic Flow Templates for all active secondary and non secondary
PDP contexts are returned.
Parameters of both network and MT/TA initiated PDP contexts will be returned.
The test command returns a list of <cid>s associated with active secondary and non secondary contexts.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
255
3GPP TS 27.007 version 13.3.0 Release 13
Defined values
<cid>: integer type; Specifies a particular secondary or non secondary PDP context definition or Traffic Flows
definition (see +CGDCONT and +CGDSCONT commands).
For the following parameters, see also 3GPP TS 23.060 [47]
<packet filter identifier>: integer type. The value range is from 1 to 16.
<evaluation precedence index>: integer type. The value range is from 0 to 255.
<remote address and subnet mask>: string type. The string is given as dot-separated numeric (0-255)
parameters on the form:
"a1.a2.a3.a4.m1.m2.m3.m4" for IPv4 or
"a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16.m1.m2.m3.m4.m5.m6.m7.m8.m9.m10.m11.m12.m13.
m14.m15.m16" for IPv6.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the execute
form of +CGTFTRDP.
<protocol number (ipv4) / next header (ipv6)>: integer type. The value range is from 0 to 255.
<local port range>: string type. The string is given as dot-separated numeric (0-65535) parameters on the
form "f.t".
<remote port range>: string type. The string is given as dot-separated numeric (0-65535) parameters on the
form "f.t".
<ipsec security parameter index (spi)>: numeric value in hexadecimal format. The value range is
from 00000000 to FFFFFFFF.
<type of service (tos) (ipv4) and mask / traffic class (ipv6) and mask>:
string type. The string is given as dot-separated numeric (0-255) parameters on the form "t.m".
<flow label (ipv6)>: numeric value in hexadecimal format. The value range is from 00000 to FFFFF. Valid
for IPv6 only.
<direction> integer type. Specifies the transmission direction in which the Packet Filter shall be applied.
0 Pre Release 7 TFT Filter (see 3GPP TS 24.008 [8], table 10.5.162)
1 Uplink
2 Downlink
3 Bidirectional (Used for Uplink and Downlink)
<NW packet filter Identifier> integer type. The value range is from 1 to 16. In EPS the value is
assigned by the network when established
<local address and subnet mask>: string type. The string is given as dot-separated numeric (0-255)
parameters on the form:
"a1.a2.a3.a4.m1.m2.m3.m4" for IPv4 or
"a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16.m1.m2.m3.m4.m5.m6.m7.m8.m9.m10.m11.m12.m13.
m14.m15.m16", for IPv6.
When +CGPIAF is supported, its settings can influence the format of this parameter returned with the read form
of +CGTFTRDP.
NOTE: Some of the above listed attributes can coexist in a Packet Filter while others mutually exclude each
other. The possible combinations are shown in 3GPP TS 23.060 [47].
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
256
3GPP TS 27.007 version 13.3.0 Release 13
10.1.26 Define EPS quality of service +CGEQOS
Table 10.1.26-1: +CGEQOS parameter command syntax
Command
Possible Response(s)
+CGEQOS=[<cid>[,<QCI>[,<DL_GBR>,<UL_GBR
>[,<DL_MBR>,<UL_MBR]]]] +CM
E
ERROR: <err>
+CGEQOS? [+CGEQOS: <cid>,<QCI>,[<DL_GBR>,<UL_GBR
>],[<DL_MBR>,<UL_MBR>]]
[<CR><LF>+CGEQOS: <cid>,<QCI>,[<DL_GBR>
,<UL_GBR>],[<DL_MBR>,<UL_MBR>]
[...]]
+CGEQOS=?
+CGEQOS: (range of supported <cid>s),(list of
supported <QCI>s),(list of supported
<DL_GBR>s),(list of supported <UL_GBR>s),(list of
supported <DL_MBR>s),(list of supported
<UL_MBR>s)
Description
The set command allows the TE to specify the EPS Quality of Service parameters <cid>, <QCI>, [<DL_GBR> and
<UL_GBR>] and [<DL_MBR> and <UL_MBR>] for a PDP context or Traffic Flows (see 3GPP TS 24.301 [83] and
3GPP TS 23.203 [85]). When in UMTS/GPRS the MT applies a mapping function to UTMS/GPRS Quality of Service.
Refer subclause 9.2 for possible <err> values.
A special form of the set command, +CGEQOS= <cid> causes the values for context number <cid> to become
undefined.
The read command returns the current settings for each defined QoS.
The test command returns the ranges of the supported parameters as compound values.
Defined values
<cid>: integer type; specifies a particular EPS Traffic Flows definition in EPS and a PDP Context definition in
UMTS/GPRS (see the +CGDCONT and +CGDSCONT commands).
<QCI>: integer type; specifies a class of EPS QoS (see 3GPP TS 23.203 [85] and 3GPP TS 24.301 [83]).
0 QCI is selected by network
[1 – 4] value range for guaranteed bit rate Traffic Flows
[5 – 9] value range for non-guarenteed bit rate Traffic Flows
[128 – 254] value range for Operator-specific QCIs
The QCI values 65, 66, 69 and 70 are not allowed to be requested by the UE. If the TE requests a QCI parameter 65, 66,
69 or 70, the MT responds with result code +CME ERROR: 181 (unsupported QCI value).
<DL_GBR>: integer type; indicates DL GBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
<UL_GBR>: integer type; indicates UL GBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
<DL_MBR>: integer type; indicates DL MBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
257
3GPP TS 27.007 version 13.3.0 Release 13
<UL_MBR>: integer type; indicates UL MBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
Implementation
Optional.
10.1.27 EPS quality of service read dynamic parameters +CGEQOSRDP
Table 10.1.27-1: +CGEQOSRDP action command syntax
Command
Possible Response(s)
+CGEQOSRDP[=<cid>] [+CGEQOSRDP: <cid>,<QCI>,[<DL_GBR>,<UL_GBR>]
,[<DL_MBR>,<UL_MBR>][,<DL_AMBR>,<UL_AMBR>]]
[<CR><LF>+CGEQOSRDP: <cid>,<QCI>,[<DL_GBR>,<
UL_GBR>],[<DL_MBR>,<UL_MBR>][,<DL_AMBR>,<UL_
AMBR>]
[...]]
+CGEQOSRDP=? +CGEQOSRDP: (list of <cid>s associated with active
contexts)
NOTE: The syntax of the AT Set Command is corrected to be according to
ITU-T Recommendation V.250 [14]. Older versions of the specification specify incorrect
syntax +CGEQOSRDP=[<cid>]
Description
The execution command returns the Quality of Service parameters <QCI>, [<DL_GBR> and <UL_GBR>] and
[<DL_MBR> and <UL_MBR>] of the active secondary or non secondary PDP context associated to the provided
context identifier <cid>.
If the parameter <cid> is omitted, the Quality of Service parameters for all secondary and non secondary active PDP
contexts are returned.
The test command returns a list of <cid>s associated with secondary or non secondary active PDP contexts.
Parameters of both network and MT/TA initiated PDP contexts will be returned.
Defined values
<cid>: integer type; specifies a particular Traffic Flows definition in EPS and a PDP Context definition in
UMTS/GPRS (see the +CGDCONT and +CGDSCONT commands).
<QCI>: integer type; specifies a class of EPS QoS (see 3GPP TS 23.203 [85] and 3GPP TS 24.301 [83]).
0 QCI is selected by network
[1 – 4] value range for guranteed bit rate Traffic Flows
[65 – 66] value range for guaranteed bit rate Traffic Flows
[5 – 9] value range for non-guarenteed bit rate Traffic Flows
[69 – 70] value range for non-guaranteed bit rate Traffic Flows
[128 – 254] value range for Operator-specific QCIs
<DL_GBR>: integer type; indicates DL GBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
258
3GPP TS 27.007 version 13.3.0 Release 13
<UL_GBR>: integer type; indicates UL GBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
<DL_MBR>: integer type; indicates DL MBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
<UL_MBR>: integer type; indicates UL MBR in case of GBR QCI. The value is in kbit/s. This parameter is omitted
for a non-GBR QCI (see 3GPP TS 24.301 [83]).
<DL_AMBR>: integer type; indicates DL APN aggregate MBR (see 3GPP TS 24.301 [83]). The value is in kbit/s.
<UL_AMBR>: integer type; indicates UL APN aggregate MBR (see 3GPP TS 24.301 [83]). The value is in kbit/s.
NOTE: If multiple lines in a response belong to the same PDN connection they contain the same <DL_AMBR>
<UL_AMBR> values.
Implementation
Optional.
10.1.28 UE modes of operation for EPS +CEMODE
Table 10.1.28-1: +CEMODE parameter command syntax
Command
Possible Response(s)
+CEMODE=[<mode>] +CM
E
ERROR: <err>
+CEMODE? +CEMODE: <mode>
+CEMODE=? +CEMODE: (
list of supported
<mode>
s
)
Description
The set command is used to set the MT to operate according to the specified mode of operation for EPS, see
3GPP TS 24.301 [83]. If the requested mode of operation is not supported, an ERROR or +CME ERROR response is
returned. Extended error responses are enabled by the +CMEE command. Refer subclause 9.2 for possible <err>
values.
The read command returns the mode of operation set by the TE, independent of the current serving cell capability and
independent of the current serving cell Access Technology.
The test command is used for requesting information on the supported MT modes of operation as a compound value.
Defined Values
<mode>: integer type; indicates the mode of operation. The default value is manufacturer specific.
0 PS mode 2 of operation
1 CS/PS mode 1 of operation
2 CS/PS mode 2 of operation
3 PS mode 1 of operation
NOTE: the definition for UE modes of operation can be found in 3GPP TS 24.301 [83]
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
259
3GPP
TS 27.007 version 13.3.0 Release 13
10.1.29 Delete non-active PDP contexts +CGDEL
Table 10.1.29-1: +CGDEL action command syntax
Command
Possible Response(s)
+CGDEL[=<cid>] [+CGDEL: <cid>[,<cid>[,...]]]
+CME ERROR: <err>
+CGDEL=?
Description
The execution command +CGDEL=<cid> removes the indicated PDP context and removes all associated data related
to the indicated PDP contexts that are not activated. The AT command will not delete or remove information for
activated PDP contexts. The removed PDP context is listed by the +CGDEL: <cid> intermediate result code. If the
initial PDP context is supported (see subclause 10.1.0), +CGDEL=0 will return ERROR and the context will not be
removed.
If <cid> points to a primary PDP context, the PDP context will be deleted together with all linked secondary PDP
contexts if none of the PDP contexts are activated.
If <cid> points to a secondary PDP context, the PDP context will be deleted if it is not activated.
A special form of the command can be given as +CGDEL (with the =<cid> omitted). In this form, all primary PDP
contexts that are not activated or have any activated secondary PDP contexts will be removed and all secondary PDP
contexts that are not activated will be removed. The associated data of all the deleted PDP contexts will be removed,
and the removed PDP context are listed by the +CGDEL: <cid>[,<cid>[,...]] intermediate result code.
Activated PDP contexts will not cause this form of the command to return ERROR or +CME ERROR. Refer
subclause 9.2 for possible <err> values.
If the initial PDP context is supported (see subclause 10.1.0), +CGDEL (with the =<cid> omitted) will not cause the
initial PDP context to be removed or cause +CGDEL to return ERROR.
NOTE: +CGDEL will remove associated PDP context data that can be set by the AT commands +CGDCONT,
+CGDSCONT, +CGTFT, +CGEQREQ, +CGEQMIN and +CGEQOS.
For an attempt to delete PDP context(s) which would violate these rules, a +CME ERROR response is returned. Refer
subclause 9.2 for possible <err> values.
Defined values
<cid>: integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
Implementation
Optional.
10.1.30 Signalling connection status +CSCON
Table 10.1.30-1: +CSCON parameter command syntax
Command
Possible response(s)
+CSCON=[<n>] +CME ERROR: <err>
+CSCON? +CSCON: <n>,<mode>[,<state>]
+CME ERROR: <err>
+CSCON=?
+CSCON: (list of supported <n>s)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
260
3GPP TS 27.007 version 13.3.0 Release 13
Description
The set command controls the presentation of an unsolicited result code +CSCON. If <n>=1, +CSCON: <mode> is
sent from the MT when the connection mode of the MT is changed. If <n>=2 and there is a state within the current
mode, +CSCON: <mode>[,<state>] is sent from the MT. If <n>=3,
+CSCON: <mode>[,<state>[,<access>]] is sent from the MT. If setting fails, an MT error,
+CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err> values.
When the MT is in UTRAN or E-UTRAN, the mode of the MT refers to idle when no PS signalling connection and to
connected mode when a PS signalling connection between UE and network is setup. When the UE is in GERAN, the
mode refers to idle when the MT is in either the IDLE state or the STANDBY state and to connected mode when the
MT is in READY state.
The <state> value indicates the state of the MT when the MT is in GERAN, UTRAN connected mode or E-UTRAN.
The read command returns the status of result code presentation and an integer <mode> which shows whether the MT
is currently in idle mode or connected mode. State information <state> is returned only when <n>=2. Radio access
type information <access> is returned only when <n>=3.
Test command returns supported values as a compound value.
Defined values
<n>: integer type
0 disable unsolicited result code
1 enable unsolicited result code +CSCON: <mode>
2 enable unsolicited result code +CSCON: <mode>[,<state>]
3 enable unsolicited result code +CSCON: <mode>[,<state>[,<access>]]
<mode>: integer type; indicates the signalling connection status
0 idle
1 connected
<state>: integer type; indicates the CS or PS state while in GERAN and the RRC state information if the MT is in
connected Mode while in UTRAN and E-UTRAN.
0 UTRAN URA_PCH state
1 UTRAN Cell_PCH state
2 UTRAN Cell_FACH state
3 UTRAN Cell_DCH state
4 GERAN CS connected state
5 GERAN PS connected state
6 GERAN CS and PS connected state
7 E-UTRAN connected state
<access>: integer type; indicates the current radio access type.
0 Indicates usage of radio access of type GERAN, see 3GPP TS 45.001 [146].
1 Indicates usage of radio access of type UTRAN TDD, see 3GPP TS 25.212 [144].
2 Indicates usage of radio access of type UTRAN FDD, see 3GPP TS 25.212 [144].
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
261
3GPP TS 27.007 version 13.3.0 Release 13
3 Indicates usage of radio access of type E-UTRAN TDD, see 3GPP TS 36.300 [145].
4 Indicates usage of radio access of type E-UTRAN FDD, see 3GPP TS 36.300 [145].
Implementation
Optional.
10.1.31 Define PDP context authentication parameters +CGAUTH
Table 10.1.31-1: +CGAUTH parameter command syntax
Command
Possible response(s)
+CGAUTH=<cid>[,<auth_prot>[,
<userid>[,<password>]]] +CME ERROR: <err>
+CGAUTH? [+CGAUTH: <cid>,<auth_prot>,<userid>,<pass
word>]
[<CR><LF>+CGAUTH: <cid>,<auth_prot>,<useri
d>,<password>
[...]]
+CGAUTH=? +CGAUTH: (range of supported <cid>s),(list of supported
<auth_prot>s),(range of supported <userid>s),(range
of supported <password>s)
Description
Set command allows the TE to specify authentication parameters for a PDP context identified by the (local) context
identification parameter <cid> used during the PDP context activation and the PDP context modification procedures.
Since the <cid> is the same parameter that is used in the +CGDCONT and +CGDSCONT commands, +CGAUTH is
effectively as an extension to these commands. Refer subclause 9.2 for possible <err> values.
The read command returns the current settings for each defined context.
The test command returns values supported as compound values.
Defined values
<cid>: integer type. Specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
<auth_prot>: integer type. Authentication protocol used for this PDP context.
0 None. Used to indicate that no authentication protocol is used for this PDP context. Username and password
are removed if previously specified.
1 PAP
2 CHAP
<userid>: String type. User name for access to the IP network.
<password>: String type. Password for access to the IP network.
Implementation
Optional.
4+
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
262
3GPP TS 27.007 version 13.3.0 Release 13
10.1.32 Initial PDP context activation +CIPCA
Table 10.1.32-1: +CIPCA parameter command syntax
Command
Possible response(s)
+CIPCA=[<n>]
+CIPCA? +CIPCA: <n>
+CIPCA=? +CIPCA: (list of supported <n>s)
Description
The set command controls whether an initial PDP context (see subclause 10.1.0) shall be established automatically
following an attach procedure when the UE is attached to GERAN or UTRAN RATs. For <n> 0, deactivating the last
(active) PDP context can lead to a (re)establishment of the initial PDP context. Changing setting of <n> from 0 to 1 will
cause an immediate attempt to (re)establish the initial PDP context if no PDP context is active. Changing <n> from 0
to 2 will if not roaming cause an immediate attempt to (re)establish the initial PDP context if no other PDP context is
active. Changing <n> will never cause a PDP context deactivation.
NOTE 1: This command does not affect connectivity behavior in E-UTRAN, which mandates the UE to establish a
PDP context upon attach.
NOTE 2: For this command, the term roaming corresponds to being registered to a VPLMN which is not equivalent
to HPLMN or EHPLMN.
The read command returns the current setting of the command.
The test command returns values supported as a compound value.
Defined values
<n>: integer type. Activation of PDP context upon attach.
0 Do not activate
1 Always activate
2 Activate when not roaming
Implementation
Optional.
10.1.33 No more PS data +CNMPSD
Table 10.1.33-1: +CNMPSD action command syntax
Command
Possible Response(s)
+CNMPSD
+CNMPSD=?
Description
This command indicates that no application on the MT is expected to exchange data.
When in UTRAN, if further conditions defined in 3GPP TS 25.331 [74] are met, this can cause transmission of a
SIGNALLING CONNECTION RELEASE INDICATION message with the cause "UE Requested PS Data session
end".
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
263
3GPP TS 27.007 version 13.3.0 Release 13
When in E-UTRAN, if further conditions defined in 3GPP TS 36.331 [86] are met, this can cause transmission of a
UEAssistanceInformation message with powerPrefIndication set to "lowPowerConsumption" to the network.
NOTE: See subclause 10.1.38 for a command applicable to an MT using E-UTRAN, where the MT has a
preference for a configuration that is not optimized for power saving.
This command may be used in both normal and modem compatibility modes.
Implementation
Optional.
10.1.34 UE's usage setting for EPS +CEUS
Table 10.1.34-1: +CEUS parameter command syntax
Command
Possible Response(s)
+CEUS=[<setting>]
+CEUS? +CEUS: <setting>
+CEUS=? +CEUS: (
list of supported
<setting>
s
)
Description
The set command is used to set the MT to operate according to the specified UE's usage setting for EPS, see
3GPP TS 24.301 [83].
The read command returns the usage setting set by the TE.
The test command is used for requesting information on the supported MT setting(s) as a compound value.
Defined Values
<setting>: integer type; indicates the usage setting of the UE. The default value is manufacturer specific.
0 voice centric
1 data centric
NOTE: The definition for usage settings of the UE can be found in 3GPP TS 24.301 [83].
Implementation
Optional.
10.1.35 UE's Voice Domain Preference E-UTRAN +CEVDP
Table 10.1.35-1: +CEVDP parameter command syntax
Command
Possible Response(s)
+CEVDP=[<setting>]
+CEVDP? +CEVDP: <setting>
+CEVDP=? +CEVDP: (
list of supported
<setting>
s
)
Description
The set command is used to set the MT to operate according to the specified voice domain preference for E-UTRAN.
The read command returns the setting, independent of the current serving cell capability and independent of the current
serving cell'
s
access technology.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
264
3GPP TS 27.00
7 version 13.3.0 Release 13
Test command returns supported values as a compound value.
Defined Values
<setting>: integer type; indicates the voice domain preference of the UE. The default value is manufacturer
specific.
1 CS Voice only
2 CS Voice preferred, IMS PS Voice as secondary
3 IMS PS Voice preferred, CS Voice as secondary
4 IMS PS Voice only
NOTE: The definition for the UE's voice domain preference for E-UTRAN can be found in
3GPP TS 24.167 [102], subclause 5.27.
Implementation
Optional.
10.1.36 UE's Voice Domain Preference UTRAN +CVDP
Table 10.1.36-1: +CVDP parameter command syntax
Command
Possible Response(s)
+CVDP=[<setting>]
+CVDP? +CVDP: <setting>
+CVDP=? +CVDP: (
list of supported
<setting>
s
)
Description
The set command is used to set the MT to operate according to the specified voice domain preference for UTRAN.
The read command returns the setting, independent of the current serving cell capability and independent of the current
serving cell'
s
access technology.
Test command returns supported values as a compound value.
Defined Values
<setting>: integer type; indicates the voice domain preference of the UE. The default value is manufacturer
specific.
1 CS Voice only
2 CS Voice preferred, IMS PS Voice as secondary
3 IMS PS Voice preferred, CS Voice as secondary
NOTE: The definition for the UE's voice domain preference for UTRAN can be found in 3GPP TS 24.167 [102],
subclause 5.30.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
265
3GPP TS 27.007 version 13.3.0 Release 13
10.1.37 UE's Mobility Management IMS Voice Termination +CMMIVT
Table 10.1.QT3-1: +CMMIVT parameter command syntax
Command
Possible Response(s)
+CMMIVT=[<setting>]
+CMMIVT? +CMMIVT: <setting>
+CMMIVT=? +CMMIVT: (
list of supported
<setting>
s
)
Description
The set command is used to set the MT to perfom additional procedures as specified in 3GPP TS 24.008 [8] and
3GPP TS 24.301 [83] to support terminating access domain selection by the network.
The read command returns the setting, independent of the current serving cell capability and independent of the current
serving cell'
s
access technology.
Test command returns supported values as a compound value.
Defined Values
<setting>: integer type; indicates the mobility management IMS voice termination preference of the UE. The
default value is manufacturer specific.
1 Mobility Management for IMS Voice Termination disabled
2 Mobility Management for IMS Voice Termination enabled
NOTE: The definition of the UE's mobility management IMS voice termination values can be found in
3GPP TS 24.167 [102], subclause 5.31.
Implementation
Optional.
10.1.38 Power Preference Indication for EPS +CEPPI
Table 10.1.38-1: +CEPPI action command syntax
Command
Possible Response(s)
+CEPPI=<power preference>
+CEPPI=? +CEPPI: (
list of supported
<power
preference>s)
Description
This command indicates whether the MT prefers a configuration primarily optimised for power saving or not. Upon
receiving this command, the final result code OK is returned.
When in E-UTRAN, if further conditions defined in 3GPP TS 36.331 [86] are met, this can cause transmission of a
UEAssistanceInformation message with powerPrefIndication set to <power preference> to the network.
This command may be used in both normal and modem compatibility modes.
Test command returns the values supported as a compound value.
Defined Values
<power preference>: integer type; indicates the power consumption preference of the MT.
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
266
3GPP TS 27.007 version 13.3.0 Release 13
0 normal
1 low power consumption
Implementation
Optional.
10.1.39 WLAN offload assistance data +CWLANOLAD
Table 10.1.39-1: +CWLANOLAD parameter command syntax
Command
Possible response(s)
+CWLANOLAD=[<n>] +CME ERROR: <err>
+CWLANOLAD? +CWLANOLAD: <n>[,<threshRSCPLow>,<threshRSCPHigh>[,<thre
shEcnoLow>,<threshEcnoHigh>[,<threshRSRPLow>,<threshRSRP
High>[,<threshRSRQLow>,<threshRSRQHigh>[,<threshChUtilLo
w>,<threshChUtilHigh>[,<threshBackhRateDLLow>,<threshBac
khRateDLHigh>[,<threshBackhRateULLow>,<threshBackhRateUL
High>[,<threshBeaconRSSILow>,<threshBeaconRSSIHigh>[,<op
i>[,<tSteering>[,<WLANIdentifierListLength>[,<ssid_1>,<b
ssid_1>,<hessid_1>][,<ssid_2>,<bssid_2>,<hessid_2>][,...
…]]]]]]]]]]]]
+CWLANOLAD=?
+CWLANOLAD: (list of supported <n>s),(list of supported
<threshRSCPLow>s),(list of supported <threshRSCPHigh>s),(list of
supported <threshEcnoLow>s),(list of supported
<threshEcnoHigh>s),(list of supported <threshRSRPLow>s),(list of
supported <threshRSRPHigh>s),(list of supported
<threshRSRQLow>s),(list of supported <threshRSRQHigh>s),(list of
supported <threshChUtilLow>s),(list of supported
<threshChUtilHigh>s),(list of supported
<threshBackhRateDLLow>s),(list of supported
<threshBackhRateDLHigh>s),(list of supported
<threshBackhRateULLow>s),(list of supported
<threshBackhRateULHigh>s),(list of supported
<threshBeaconRSSILow>s),(list of supported
<threshBeaconRSSIHigh>s),(list of supported <tSteering>s),(list of
supported <WLANIdentifierListLength>s)
Description
Set command enables or disables the WLAN offload assistance data reporting. If reporting is enabled by <n>=1, the
MT returns the following unsolicited result code from MT to TE whenever the WLAN offload assistance data changes
at the MT:
+CWLANOLADI: [,<threshRSCPLow>,<threshRSCPHigh>[,<threshEcnoLow>,<threshEcnoHigh
>[,<threshRSRPLow>,<threshRSRPHigh>[,<threshRSRQLow>,<threshRSRQHigh>[,<threshCh
UtilLow>,<threshChUtilHigh>[,<threshBackhRateDLLow>,<threshBackhRateDLHigh>[,<th
reshBackhRateULLow>,<threshBackhRateULHigh>[,<threshBeaconRSSILow>,<threshBeacon
RSSIHigh>[,<opi>[,<tSteering>[,<WLANIdentifierListLength>[,<ssid_1>,<bssid_1>,<h
essid_1>][,<ssid_2>,<bssid_2>,<hessid_2>][,...]]]]]]]]]]]]
Refer IE WLAN-OffloadConfig in 3GPP TS 36.331 [86] subclause 6.3.6.
If a setting is not supported by the MT, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err>
values.
Read command returns the current status of <n> and the WLAN offload assistance data currently available at the MT.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
267
3GPP TS 27.007 version 13.3.0 Release 13
Test command returns the values supported by MT as compound values.
Defined values
<n>: integer type
0 disable WLAN offload assistance data unsolicited result code
1 enable WLAN offload assistance data unsolicited result code +CWLANOLADI
<threshRSCPLow>: integer type; indicates the threshold for received signal code power for offloading traffic
from UTRAN to WLAN. Refer parameter <rscp> in subclause 8.69.
<threshRSCPHigh>: integer type; indicates the threshold for received signal code power for offloading traffic
from WLAN to UTRAN. Refer parameter <rscp> in subclause 8.69.
<threshEcnoLow>: integer type; indicates the threshold for ratio of the received energy per PN chip to the total
received power spectral density for offloading traffic from UTRAN to WLAN. Refer parameter <ecno> in
subclause 8.69.
<threshEcnoHigh>: integer type; indicates the threshold for ratio of the received energy per PN chip to the total
received power spectral density for offloading traffic from WLAN to UTRAN. Refer parameter <ecno> in
subclause 8.69.
<threshRSRPLow>: integer type; indicates the threshold for reference signal received power for offloading traffic
from E-UTRAN to WLAN. Refer parameter <rsrp> in subclause 8.69.
<threshRSRPHigh>: integer type; indicates the threshold for reference signal received power for offloading
traffic from WLAN to E-UTRAN. Refer parameter <rsrp> in subclause 8.69.
<threshRSRQLow>: integer type; indicates the threshold for reference signal received quality for offloading
traffic from E-UTRAN to WLAN. Refer parameter <rsrq> in subclause 8.69.
<threshRSRQHigh>: integer type; indicates the threshold for reference signal received quality for offloading
traffic from WLAN to E-UTRAN. Refer parameter <rsrq> in subclause 8.69.
<threshChUtilLow>: integer type; indicates the low threshold value of WLAN channel utilization (BSS
load).obtained from 802.11 (Beacon or Probe Response) signalling, see IEEE 802.11 [152].
<threshChUtilHigh>: integer type; indicates the high threshold value of WLAN channel utilization (BSS load)
obtained from 802.11 (Beacon or Probe Response) signalling, see IEEE 802.11 [152].
<threshBackhRateDLLow>: integer type; indicates the low threshold value of backhaul available downlink
bandwidth for traffic offloading to UTRAN or E-UTRAN, see Hotspot 2.0 (Release 2) Technical
Specification [151].
<threshBackhRateDLHigh>: integer type; indicates the high threshold value of backhaul available downlink
bandwidth for traffic offloading to WLAN, see Hotspot 2.0 (Release 2) Technical Specification [151].
<threshBackhRateULLow>: integer type; indicates the low threshold value of backhaul available uplink
bandwidth for traffic offloading to UTRAN or E-UTRAN, see Hotspot 2.0 (Release 2) Technical
Specification [151].
<threshBackhRateDLHigh>: integer type; indicates the high threshold value of backhaul available uplink
bandwidth for traffic offloading to WLAN. Refer to Hotspot 2.0 (Release 2) Technical Specification [151].
<threshBeaconRSSILow>: integer type; indicates the low threshold value of beaon RSSI used for traffic
offloading to UTRAN or E-UTRAN see IEEE 802.11 [152].
<threshBeaconRSSIHigh>: integer type; indicates the high threshold value of beaon RSSI used for traffic
offloading to WLAN, see IEEE 802.11 [152].
<opi>: integer type;A 16-bit integer formatted as a bitmap that specifies the Offload Preference Indicator, see
3GPP TS 24.312 [153]
1N
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
268
3GPP TS 27.007 version 13.3.0 Release 13
<tSteering>: integer type; indicates the timer value in seconds during which the rules should be fulfilled before
starting traffic offloading between E-UTRAN and WLAN.
<WLANIdentifierListLength>: integer type; indicates the number of entries in WLAN identifier list which
is a tuple consisting of the <ssid>, the <bssid>and the <hessid> identifiers. If an identifier is not present
for a tuple, it will be indicated as an empty string.
<ssid>: string type; indicates the 802.11 Service Set Identifier (SSID), see IEEE 802.11 [152].
<bssid>: string type; indicates the 802.11 Basic Service Set Identifier (BSSID), see IEEE 802.11 [152].
<hessid>: string type; indicates the 802.11 Homogenous Extended Service Set Identifier (HESSID), see
IEEE 802.11 [152].
Implementation
Optional.
10.1.40 WLAN offload cell measurement +CWLANOLCM
Table 10.1.40-1: +CWLANOLCM parameter command syntax
Command
Possible response(s)
+CWLANOLCM=[<n>] +CME ERROR: <err>
+CWLANOLCM? +CWLANOLCM: <n>,<rscp>,<ecno>,<rsrp>,<rsrq>
+CWLANOLCM=?
+CWLANOLCM: (list of supported <n>s),(list of supported <rscp>s),(
list
of supported <ecno>s),(list of supported <rsrp>s),(list of supported
<rsrq>s)
Description
Set command enables or disables the indication for WLAN offloading based on the thresholds for cell measurement
parameters. If reporting is enabled by <n>=1, the MT returns the following unsolicited result code from MT to TE
whenever the cell measurement parameters meet the criteria for WLAN offloading based on configured thresholds:
+CWLANOLCMI: <rscp>,<ecno>,<rsrp>,<rsrq>
If a setting is not supported by the MT, +CME ERROR: <err> is returned. Refer subclause 9.2 for possible <err>
values.
Read command returns the current status of result code presentation and the measurements from the current primary
serving cell at the MT.
Test command returns the values supported by MT as compound values.
Defined values
<n>: integer type
0 disable WLAN offload cell measurement unsolicited result code
1 enable WLAN offload cell measurement unsolicited result code +CWLANOLCMI
<rscp>: integer type; indicates the received signal code power. Refer parameter <rscp> in subclause 8.69.
<ecno>: integer type; indicates the ratio of the received energy per PN chip to the total received power spectral
density. Refer parameter <ecno> in subclause 8.69.
<rsrp>: integer type; indicates the reference signal received power. Refer parameter <rsrp> in subclause 8.69.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
269
3GPP TS 27.007 versio
n 13.3.0 Release 13
<rsrq>: integer type; indicates the reference signal received quality. Refer parameter <rsrq> in subclause 8.69.
Implementation
Optional.
10.2 Modem compatibility commands
10.2.0 General
This subclause describes how existing AT commands, designed for use with a modem, may be used to control a Packet
Domain MT. This is to provide backwards compatibility with existing communications software. For new applications
it is recommended that the Packet Domain-specific commands, described in previous subclauses, be used.
10.2.1 MT originated PDP context activation
10.2.1.0 General
In this mode of operation, the MT behaves like an originating modem and accepts the normal V.250 commands
associated with placing and clearing a call. If Packet Domain-specific configuration commands are required, they may
be sent to the MT as part of the modem initialization commands.
10.2.1.1 Request packet domain service 'D'
Table 130: D command syntax
Command
Possible Response(s)
D*<GPRS_SC>[*[<called_address>][*[<L2P>]
[*[<cid>[,<cid>[,...]]]]]]# CONNECT
ERROR
Description
This command causes the MT to perform whatever actions are necessary to establish communication between the TE
and the external PDN.
The V.250 'D' (Dial) command causes the MT to enter the V.250 online data state and, with the TE, to start the
specified layer 2 protocol. The MT shall return CONNECT to confirm acceptance of the command prior to entering the
V.250 online data state. No further commands may follow on the AT command line.
The detailed behaviour after the online data state has been entered is dependent on the PDP type. It is described briefly
in clause 9 (for IP) of 3GPP TS 27.060 [34]. PS attachment and PDP context activation procedures may take place prior
to or during the PDP startup if they have not already been performed using the +CGATT and +CGACT commands.
When the layer 2 protocol has terminated, either as a result of an orderly shut down of the PDP or an error, the MT shall
enter V.250 command state and return the NO CARRIER final result code.
If <called address> is supported and provided, the MT shall automatically set up a virtual call to the specified
address after the PDP context has been activated.
If <L2P> and <cid> are supported, their usage shall be the same as in the +CGDATA command. The +CGDCONT,
+CGQREQ, etc. commands may be used in the modem initialization AT command string to set values for for PDP type,
APN, QoS etc..
If <L2P> is not supported or is supported but omitted, the MT shall use a layer 2 protocol appropriate to the PDP type.
If <cid> is not supported or is supported but omitted, the MT shall attempt to activate the context using:
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
270
3GPP TS 27.007 version 13.3.0 Release 13
(a) any information provided by the TE during the PDP startup procedure, e.g. the TE may provide a PDP type
and/or PDP address to the MT;
(b) a priori knowledge, e.g. the MT may implement only one PDP type; or
(c) using the 'Empty PDP type' (3GPP TS 24.008 [8]). (No PDP address or APN shall be sent in this case and only
one PDP context subscription record shall be present in the HLR for this subscriber.)
This command may be used in both normal and modem compatibility modes.
NOTE: The dial string conforms to the syntax specified in 3GPP TS 22.030 [19].
Defined Values
<GPRS_SC>: (GPRS Service Code) a string of digits (value 99) which identifies a request to use the Packet
Domain service
<called_address>: a string that identifies the called party in the address space applicable to the PDP. For
communications software that does not support arbitrary characters in the dial string, a numeric equivalent may
be used. Also, the character comma ',' may be used as a substitute for the character period '.'.
<L2P>: a string which indicates the layer 2 protocol to be used (see +CGDATA command). For communications
software that does not support arbitrary characters in the dial string, the following numeric equivalents shall be
used:
0 NULL (Obsolete)
1 PPP
2 PAD (Obsolete)
3 X25 (Obsolete)
9yyyy M-xxxx
Other values are reserved and will result in an ERROR response
<cid>: a string of digits which specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT
commands).
Implementation
Optional if the +CGDATA command is supported. If the D command is provided, then support for
<called_address>, <L2P> and <cid> are optional. If they are not supported but values are provided by the TE,
the values shall be ignored and this shall not constitute an error.
10.2.1.2 Request packet domain IP service 'D'
Table 131: D command syntax
Command
Possible Response(s)
D*<GPRS_SC_IP>[*<cid>[,<cid>[,...]]]# CONNECT
ERROR
Description
This command causes the MT to perform whatever actions are necessary to establish communication between the TE
and the external PDN.
The V.250 'D' (Dial) command causes the MT to enter the V.250 online data state and, with the TE, to start the
specified layer 2 protocol. The MT shall return CONNECT to confirm acceptance of the command prior to entering the
V.250 online data state. No further commands may follow on the AT command line.
13
ETSI
ETSI TS 1
27 007 V13.3.0 (2016
-
03)
271
3GPP TS 27.007 version 13.3.0 Release 13
The detailed behaviour after the online data state has been entered is described briefly in clause 9, for IP, of
3GPP TS 27.060 [34]. GPRS attachment and PDP context activation procedures may take place prior to or during the
PDP startup if they have not already been performed using the +CGATT and +CGACT commands.
When the layer 2 protocol has terminated, either as a result of an orderly shut down of the PDP or an error, the MT shall
enter V.250 command state and return the NO CARRIER final result code.
If <cid> is supported, its usage shall be the same as in the +CGDATA command. The +CGDCONT, +CGQREQ, etc.
commands may be used in the modem initialization AT command string to set values for for PDP type, APN, QoS etc.
If <cid> is not supported or is supported but omitted, the MT shall attempt to activate the context using:
(a) any information provided by the TE during the PDP startup procedure, e.g. the TE may provide a PDP type
and/or PDP address to the MT;
(b) a priori knowledge, e.g. the MT may implement only one PDP type; or
(c) using the 'Empty PDP type' (3GPP TS 24.008 [8]). (No PDP address or APN shall be sent in this case and only
one PDP context subscription record shall be present in the HLR for this subscriber.)
This command may be used in both normal and modem compatibility modes.
NOTE. The dial string conforms to the syntax specified in 3GPP TS 22.030 [19].
Defined Values
<GPRS_SC_IP>: (GPRS Service Code for IP) a string of digits (value 98) which identifies a request to use the
GPRS with IP (PDP types IP and PPP)
<cid>: a string of digits which specifies a particular PDP context definition (see +CGDCONT command).
Implementation
Optional if the +CGDATA command is supported. If the D command is provided, then support for <cid> is optional. If
it is not supported but a value is provided by the TE, the value shall be ignored and this shall not constitute an error.
10.2.2 Network requested PDP context activation
10.2.2.0 General
In this mode of operation, the MT behaves like an answering modem and accepts the normal V.250 commands
associated with answering a call. If Packet Domain-specific configuration commands are required, they may be sent to
the MT as part of the modem initialization commands.
The +CGAUTO command is used to select modem compatibility mode.
10.2.2.1 Automatic response to a network request for PDP context activation 'S0'
The V.250 'S0=n' (Automatic answer) command may be used to turn off (n=0) and on (n>0) the automatic response to a
network request for a PDP context activation.
When the 'S0=n' (n>0) command is received, the MT shall attempt to perform a PS attach if it is not already attached.
Failure will result in ERROR being returned to the TE. Subsequently, the MT will announce a network request for PDP
context activation by issuing the unsolicited result code RING to the TE, followed by the intermediate result code
CONNECT. The MT then enters V.250 online data state and follows the same procedure as it would after having
received a +CGANS=1 with no <L2P> or <cid> values specified.
NOTE: The 'S0=n' (n=0) command does not perform an automatic PS detach.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
272
3GPP TS 27.007 version 13.3.0 Release 13
10.2.2.2 Manual acceptance of a network request for PDP context activation 'A'
The V.250 'A' (Answer) command may be used to accept a network request for a PDP context activation announced by
the unsolicited result code RING. The MT responds with CONNECT, enters V.250 online data state and follows the
same procedure as it would after having received a +CGANS=1 with no <L2P> or <cid> values specified. It is an
error to issue the 'A' command when there is no outstanding network request.
Implementation
Optional.
10.2.2.3 Manual rejection of a network request for PDP context activation 'H'
The V.250 'H' or 'H0' (On-hook) command may be used to reject a network request for PDP context activation
announced by the unsolicited result code RING. The MT responds with OK. It is an error to issue the 'H' command when
there is no outstanding network request.
NOTE: This is an extension to the usage of the 'H' command that is described in ITU-
T Recommendation V.250 [14].
Implementation
Optional.
11 Commands for VGCS and VBS
11.0 General
This clause defines commands that a TE may use to control a VGCS or VBS supporting MT. The requirements for the
VGCS and VBS are included in the following specifications:
- Voice Group Call service (VGCS): 3GPP TS 42.068 [55], 3GPP TS 43.068 [49] and 3GPP TS 44.068 [52];
- Voice Broadcast Service (VBS): 3GPP TS 42.069 [56], 3GPP TS 43.069 [50] and 3GPP TS 44.069 [53].
It is anticipated that VGCS or VBS supporting MTs will vary widely in functionality.
A comprehensive set of VGCS and VBS-specific commands is defined in subclause 11.1 to provide the flexibility
needed by the more complex MT. The commands use the extended information and error message capabilities
described in this specification.
For the simplest MTs, and for backwards compatibility with existing communications software, it is possible to control
access to the VGCS and VBS using existing modem-compatible commands. A special dial-string syntax is defined for
use with the D command. This "modem compatible" mode of operation is described in subclause 11.2.
11.1 Commands specific to MTs supporting the VGCS and VBS
11.1.1 Accept an incoming voice group or voice broadcast call +CAJOIN
Table 132: +CAJOIN action command syntax
Command
Possible Response(s)
+CAJOIN=<service>,<GId>,<GCA> +CM
E
ERROR: <err>
+CAJOIN=?
Description
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
273
3GPP TS 27.007 version 13.3.0 Release 13
The execute command accepts an incoming or ongoing voice group or voice broadcast call. Refer subclause 9.2 for
possible <err> values.
See command +CALCC to get a list of current voice group or voice broadcast calls.
Defined Values
<GId>: string of digits that specifies the group identification for the incoming voice group or voice broadcast call.
<GCA>: string of digits that specifies the group call area identification for the incoming voice group or voice
broadcast call.
<service>: integer type (tele-service)
17 voice group call
18 voice broadcast call
Implementation
Mandatory for a MT supporting AT commands only and VGCS or VBS is implemented.
11.1.2 Reject an incoming voice group or voice broadcast call +CAREJ
Table 133: +CAREJ action command syntax
Command
Possible Response(s)
+CAREJ=<service>,<GId>,<GCA> +CM
E
ERROR: <err>
+CAREJ=?
Description
The execute command rejects an incoming voice group or voice broadcast call indicated by RING or +CRING, the
command is applicable as long as the indication is pending. Refer subclause 9.2 for possible <err> values.
If the call is once rejected the RING or +CRING indication is not repeated to TE although the call is still running and
notifications for the call are received.
See command +CALCC to get a list of current voice group or voice broadcast calls.
Defined Values
<GId>: string of digits that specifies the group identification for the incoming voice group or voice broadcast call.
<GCA>: string of digits that specifies the group call area identification for the incoming voice group or voice
broadcast call.
<service>: integer type (tele-service)
17 voice group call
18 voice broadcast call
Implementation
Mandatory for a MT supporting AT commands only and VGCS or VBS is implemented.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
274
3GPP TS 27.007 version 13.3.0
Release 13
11.1.3 Leave an ongoing voice group or voice broadcast call +CAHLD
Table 134: +CAHLD action command syntax
Command
Possible Response(s)
+CAHLD +CM
E
ERROR: <err>
+CAHLD=?
Description
The execute command forces the MT to leave the active voice group or voice broadcast call without terminating it. The
command is only applicable if the MT is in group receive mode. The MT returns to idle mode. Refer subclause 9.2 for
possible <err> values.
Implementation
Mandatory for a MT supporting AT commands only and VGCS or VBS is implemented.
11.1.4 Talker access for voice group call +CAPTT
Table 135: +CAPTT parameter command syntax
Command
Possible Response(s)
+CAPTT=[<mode>[,<time>]] +CM
E
ERROR: <err>
+CAPTT? +CAPTT: <mode>
+CME ERROR: <err>
+CAPTT=? +CAPTT: (
list of supported
<mode>
s
),(
list of
supported <time>s)
Description
The execute command emulates the Push To Talk function for VGCS talker access. If the parameter <mode> is set to
value "0" i.e. "R
ELEASED
" the PTT key is assumed to be released immediately. If the parameter <mode> is set to value
"1" i.e. "P
USHED
" the PTT key is assumed to be pushed immediately for the period of <time> in seconds. If the
command execution is repeated before the <time> expires the PTT timer will be loaded with the new <time> value
and the PTT key remains "P
USHED
" for the period of new <time> in seconds.
If the parameter <mode> is set to value "2" i.e. "P
USHED
" the PTT key is assumed to be pushed immediately for an
infinite period of time and can be released by <mode> value 0. For <mode>=0 if the parameter <time> is issued it is
ignored.
If the PTT timer expires after <time> seconds during <mode> "P
USHED
" an unsolicited result code +CAPTT: 0 is
issued to the TE.
Refer subclause 9.2 for possible <err> values.
The read command returns the current <mode>.
The test command returns values supported as compound values.
Defined Values
<mode>: integer type.
0 status of the PTT key is R
ELEASED
1 status of the PTT key is P
USHED
for a limited time by <time> in seconds
2 status of the PTT key is P
USHED
for an infinite time
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
275
3GPP TS 27.007 version 13.3.0 Release 13
<time>: integer type
3..255 this gives the time in seconds to wait before the PTT key is released, default value 10
Implementation
Mandatory for a MT supporting AT commands only and VGCS is implemented.
11.1.5 Voice group call uplink status presentation +CAULEV
Table 136: +CAULEV parameter command syntax
Command
Possible Response(s)
+CAULEV=[<mode>] +CM
E
ERROR: <err>
+CAULEV? +CAULEV: <mode>,[<status>]
+CME ERROR: <err>
+CAULEV=? +CAULEV: (
list of supported
<mode>
s
)
Description
The set command enables or disables the presentation of uplink access status for an active VGCS call. When enabled
the unsolicited result code +CAULEV: <status
>
is returned from MT to TE whenever the call uplink status changes.
Refer subclause 9.2 for possible <err> values.
Read command returns the current uplink <status> and the selected <mode>.
The test command returns values supported as a compound value.
Defined Values
<mode>: integer type; status of unsolicited result code presentation
0 disabled
1 enabled
<status>: integer type; network uplink access status
0 uplink free
1 uplink busy
Implementation
Mandatory for a MT supporting AT commands only and VGCS is implemented.
11.1.6 List current voice group and voice broadcast calls +CALCC
Table 137: +CALCC action command syntax
Command
Possible response(s)
+CALCC=<mode> [+CALCC: <GId>,<GCA>,<service>,<stat>,<dir>,<ack_fl
ag>[,<priority>]]
[<CR><LF>+CALCC: <GId>,<GCA>,<service>,<stat>,<dir>
,<ack_flag>[,<priority>]
[...]]
+CME ERROR: <err>
ETSI
ETSI TS 127 007 V
13.3.0 (2016
-
03)
276
3GPP TS 27.007 version 13.3.0 Release 13
+CALCC=? +CALCC: (list of supported <mode>s)
Description
The set command returns for <mode>=1 the active voice group or voice broadcast call and for <mode>=0 a list of all
current running voice group and voice broadcast calls for which the user has a subscription and the GId is activated on
the SIM. If the command succeeds but no calls are available, OK response is returned. Refer subclause 9.2 for possible
<err> values.
Test command returns the values supported as a compound value.
Defined values
<mode>: integer type
0 return a list of all current running voice group and voice broadcast calls for which the user has a subscription
and the GId is activated on the SIM
1 return the active voice group or voice broadcast call
<GId>: string of digits that specifies the group identification of the voice group or voice broadcast call.
<GCA>: string of digits that specifies the group call area of the voice group or voice broadcast call.
<service>: integer type (tele-service)
17 voice group call
18 voice broadcast call
<stat>: integer type (state of the call)
0 active, i.e. user participating at the call as talker or listener
1 held, the call is running but put to background, notifications ignored
2 incoming (MT call), the user doesn't respond to notifications of this call yet
<dir>: integer type (direction of the call)
0 mobile originated (MO) call, the user is the originator of the call
1 mobile terminated (MT) call, the user is not the originator of the call
<ack_flag>: integer type; proposes that a predefined confirmation procedure is to be used after the call is ended
0 confirmation procedure is not required
1 confirmation procedure is required
<priority>: integer type; identifies the priority level of the voice group or voice broadcast call. The values are
specified in 3GPP TS 22.067 [54].
Implementation
Optional. Recommended for an MT supporting AT commands only and VGCS or VBS is implemented.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
277
3GPP TS 27.007 version 13.3.0 Release 13
11.1.7 Voice group or voice broadcast call state attribute presentation
+CACSP
Table 138: +CACSP parameter command syntax
Command
Possible Response(s)
+CACSP=[<mode>] +CM
E
ERROR: <err>
+CACSP? +CACSP: <mode>[,<da>,<ua>,<comm>,<oi>]
+CME ERROR: <err>
+CACSP=? +CACSP: (
list of supported
<mode>
s
)
Description
The set command enables or disables the presentation of unsolicited result code
+CACSP: <da>,<ua>,<comm>,<oi> from MT to TE if the call control state attributes of the active voice group
or voice broadcast call changes.
Read command returns the current call control state attributes <da>, <ua>, <comm>, <oi> and selected <mode>.
Refer subclause 9.2 for possible <err> values.
The test command returns values supported as a compound value.
Defined Values
<mode>: integer type; status of unsolicited result code presentation
0 disabled
1 enabled
<da>: integer type. User connection in the downlink
0 not attached
1 attached
<ua>: integer type. User connection in the uplink
0 not attached
1 attached
<comm>:
integer type. The MT assumes that communication with its peer entity is
0 not enabled in both directions
1 enabled in both directions
<oi>:
integer type.
The MT assumes to be
0 not the originator of the call
1 the originator of the call
Implementation
Optional. Recommended for a MT supporting AT commands only and VGCS or VBS is implemented.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
278
3GPP TS 27.007 version 13.3.0 Release 13
11.1.8 NCH support indication +CANCHEV
Table 139: +CANCHEV parameter command syntax
Command
Possible Response(s)
+CANCHEV=[<mode>] +CM
E
ERROR: <err>
+CANCHEV? +CANCHEV: <status>,<mode>
+CME ERROR: <err>
+CANCHEV=? +CANCHEV:
(
list of supported
<mode>
s
)
Description
The set command enables or disables the presentation of unsolicited result code +CANCHEV: <status
>
from MT to
TE if the status of the network NCH support information changes.
Read command returns in parameter <status> the network NCH support information in the selected cell and the
selected <mode>.
Refer subclause 9.2 for possible <err> values.
The test command returns values supported as a compound value.
Defined Values
<mode>: integer type; status of unsolicited result code presentation
0 disabled
1 enabled
<status>: integer type; network NCH support information
0 NCH not available
1 NCH available
Implementation
Optional. Recommended for a MT supporting AT commands only and VGCS or VBS is implemented.
11.1.9 Originator to dispatcher information +COTDI
Table 140: +COTDI parameter command syntax
Command
Possible response(s)
+COTDI=<message>[,<OTDIE>[,<message>
[,<OTDIE>]]] +CME ERROR: <err>
+COTDI? [+COTDI: <message>,<OTDIE>[,<message
>,<OTDIE>]]
+COTDI=? +COTDI: (list of supported <message>s)
Description
This command allows control of the Originator-to-Dispatcher Information and Compressed Originator-to-Dispatcher
Information according to 3GPP TS 44.068 [52] and 3GPP TS 44.069 [53].
When <message> and <OTDIE> are both present the string specified in <OTDIE> is included in the corresponding
group or broadcast control <message> as the value part of the Originator-to-Dispatcher Information Element or
Compressed Originator-to-Dispatcher Information Element (as defined in 3GPP TS 44.068 [52] and
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
279
3GPP TS 27.007 version 13.3.0 Release
13
3GPP TS 44.069 [53]) into all subsequent messages of type <message>. If parameter <message> is present but
parameter <OTDIE> is not present then the Originator-to-Dispatcher Information Element shall not be present in sub-
sequent messages of type <message>. Refer subclause 9.2 for possible <err> values.
The read command returns the content of <message> and of <OTDIE>. If no <OTDIE> is available, no information
text shall be returned.
Test command returns values supported as a compound value.
Defined values
<message>: integer type
0 SETUP message containing the outgoing Originator-to-Dispatcher Information Element
1 IMMEDIATE SETUP 2 message containing the outgoing Compressed Originator-to-Dispatcher Information
Element
<OTDIE>: the Originator-to-Dispatcher Information Element or Compressed Originator-to-Dispatcher Information
Element (as defined in 3GPP TS 44.068 [52] and 3GPP TS 44.069 [53]) in hexadecimal character format (for
hexadecimal format, refer +CSCS).
Implementation
Optional.
11.1.10 Short data transmission during ongoing VGCS +CEPTT
Table 141: +CEPTT action command syntax
Command
Possible response(s)
+CEPTT=<mode>,<data>,<dataid>,<dist-
param> +CME ERROR: <err>
+CEPTT=? +CEPTT: (list of supported <mode>s),(list of
supported <dataid>s),(list of supported <dist-
param>s)
Description
The execute command emulates the Short Data Transmission during ongoing VGCS according to 3GPP TS 42.068 [55]
and 3GPP TS 43.068 [49].
The application indicator <mode> is used to identify whether the application data is an application-specific data or is a
confirmation. The data identifier <dataid> is to provide a sequence number of the sending of application data. The
value of the data identifier <dataid> is dependent on the value of the application indicator <mode>. If the
application indicator <mode> indicates sending application data to the network, the data identifier <dataid> contains
a number from the range between 0 and 15 which is generated by the mobile station. If the application indicator
<mode> indicates sending confirmation of the reception of the application data, the data identifier <dataid> shall
contain the data identifier which was received in the data identity sent by the previous sender. The distribution
parameter <dist-param> contains information to which participants shall be transferred the short data.
The response CEPTT string from the network to the other participants is returned in a subsequent unsolicited result
code +CEPTT: <mode>,<data>,<dataid>,<dist-param>[,<number>].
Refer subclause 9.2 for possible <err> values.
Test command returns values supported as compound values.
Defined values
<mode>: integer type
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
280
3GPP TS 27.007 version 13.3.0 Release 13
0 sending of application-specific data
1 confirmation of receiving application-specific data
<data>: 9 bytes application-specific data in hexadecimal character format (for hexadecimal character format, refer
+CSCS).
<dataid>: integer type, a number from the range between 0 and 15
<dist-param>: integer type, a number from the range between 1 and 7
1 data shall be distributed only to network application
2 data shall be distributed only to dispatchers
3 data shall be distributed to network application and to dispatchers
4 data shall be distributed to talkers and listeners
5 data shall be distributed to talkers and listeners and to network application
6 data shall be distributed to talkers and listeners and to dispatchers
7 data shall be distributed to network application, to talkers and listeners and to dispatchers
<mode>: integer type
Implementation
Optional.
11.1.11 Group Id prefixes capability +CGIPC
Table 11.1.11-1: +CGIPC action command syntax
Command
Possible Response(s)
+CGIPC +CGIPC: <status>
+CME ERROR: <err>
+CGIPC=?
Description
Execution command returns the MT Group Id prefix management capability, according to 3GPP TS 43.068 [49]. Refer
subclause 9.2 for possible <err> values.
Defined values
<status>: integer type, value
0 MT is not able to manage Group Id prefixes
1 MT is able to manage Group Id prefixes
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (
2016
-
03)
281
3GPP TS 27.007 version 13.3.0 Release 13
11.2 Modem compatibility commands
11.2.0 General
This sub-clause describes how existing AT commands, designed for use with a modem, may be used to control a VGCS
or VBS supporting MT. This is to provide backwards compatibility with existing communications software.
11.2.1 Request VGCS or VBS service 'D'
Table 141a: D command syntax
Command
Possible Response(s)
D*<SC
1
>[*<SC
2
>[*<SC
3
>]]#<GId>
; +CM
E
ERROR: <err>
Description
This Dial command extension is a service request application according to 3GPP TS 22.030 [19]. No further commands
may follow on the AT command line.
Responses
When the call has terminated, either as a result of an orderly termination or an error, the MT shall return the
NO CARRIER final result code.
Possible error responses include +CME ERROR: <err> when error is related to MT functionality. The requested
service, GId and priority level are checked against the subscriptions of the user and the status of the GId stored on the
SIM. In case if no subscription is available for this service, GId or priority level or the GId is deactivated an ERROR or
+CME ERROR result code is returned. The requested Group Id prefix is not checked against susbscription. The Group
Id prefixes are not stored in the SIM/USIM card. If Service Code for Group Id prefix is used, but is not managed by
MT, an ERROR or +CME ERROR result code is returned. See +CME ERROR extensions for VGCS, VBS and eMLPP in
subclause 9.2.3.
Detailed error report of an unsuccessful originated call can be obtained with command Extended Error Report +CEER
(if implemented).
NOTE 1: The dial string conforms to the syntax specified in 3GPP TS 22.030 [19].
Defined Values
<SC
1
>: Service Code is a string of digits which identifies a request to use.
17 Voice Group Call Service
18 Voice Broadcast Service
<SC
2
>: Service Code is a string of digits which identifies a request to use eMLPP priority. Service Code values for
different priority levels are specified in 3GPP TS 22.030 [19].
<GId>: a string of digits that specifies the group identification of a called party as specified in
3GPP TS 43.068 [49].
<SC
3
>: a digit that specifies a Group Id prefix as specified in 3GPP TS 43.068 [49].
NOTE 2: <SC3> is only applicable when <SC
1
> defines Voice Group Call Service.
Implementation
Mandatory for a MT supporting AT commands only and VGCS or VBS is implemented.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
282
3GPP TS 27.007 version 13.3.0 Release 13
11.2.2 Termination of an voice group or voice broadcast call 'H'
The V.250 'H' or 'H0' (On-hook) command may be used to terminate an ongoing voice group or voice broadcast call.
The MT responds with OK. It is an error to issue the 'H' command when there is no outstanding network request.
It is an error to issue the 'H' command if the user is in group receive mode or the user is not the originator of the call and
a ERROR or +CME ERROR result code is returned to the TE. Refer subclause 9.2 for possible <err> values.
NOTE: This is an extension to the usage of the 'H' command that is described in ITU-
T Recommendation V.250 [14].
Implementation
Mandatory for a MT supporting AT commands only and VGCS or VBS is implemented.
11.3 SIM commands supporting the VGCS and VBS
11.3.1 VGCS subscriptions and GId status +CGCS
Table 142: +CGCS parameter command syntax
Command
Possible response(s)
+CGCS=<GId>,<status> +CME ERROR: <err>
+CGCS? +CGCS: <GId>,<status>
[<CR><LF>+CGCS: <GId>,<status>
[...]]
+CME ERROR: <err>
+CGCS=?
+CGCS: (list of supported <GId>s),(list of
supported <status>s)
Description
This command works with SIM Card and when the GSM Application is selected in UICC. Function with USIM is for
further study. The set command is used to edit the status of the GId EF
VGCSS
on the SIM.
The read command returns all subscribed GIds in EF
VGCS
and their status in EF
VGCSS
from the SIM.
Refer subclause 9.2 for possible <err> values.
The test command returns the values supported by the UE as compound values.
Defined values
<GId> integer type, group Id as specified in 3GPP TS 22.030 [19]
<status>: integer type, value
0 deactivated
1 activated
Implementation
Mandatory for a MT supporting AT commands only and supporting VGCS.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
283
3GPP TS 27.007 version 13.3.0 Release 13
11.3.2 VBS subscriptions and GId status +CBCS
Table 143: +CBCS parameter command syntax
Command
Possible response(s)
+CBCS=<GId>,<status> +CME ERROR: <err>
+CBCS? +CBCS: <GId>,<status>
[<CR><LF>+CBCS: <GId>,<status>
[...]]
+CME ERROR: <err>
+CBCS=?
+CBCS: (list of supported <GId>s),(list of
supported <status>s)
Description
This command works with SIM Card and when the GSM Application is selected in UICC. Function with USIM is for
further study. The set command is used to edit the status of the GId EF
VBSS
on the SIM.
The read command returns all subscribed GIds in EF
VBS
and their status in EF
VBSS
from the SIM.
Refer subclause 9.2 for possible <err> values.
The test command returns the values supported by the UE as compound values.
Defined values
<GId> integer type, group Id as specified in 3GPP TS 22.030 [19]
<status>: integer type, value
0 deactivated
1 activated
Implementation
Mandatory for a MT supporting AT commands only and supporting VBS.
11.4 Informative examples
As supplementary services may be invoked and controlled using dial command according to 3GPP TS 22.030 [19].
Examples of voice group call service request usage:
ATD*17*753#500; (originate voice group call with the priority level 3)
OK (voice group call setup was successful)
ATD*17*750*3#299; (originate voice group call for Group Id 299, with Group Id prefix 3 and priority level 0)
OK (voice group call setup was successful)
ATD*17**6#599; (originate voice group call for Group Id 599, with Group Id prefix 6 and default priority selected by the
network)
OK (voice group call setup was successful)
K‘J m e ace TE > TA MT ,,,,, AI 39951? W1 Effifl’i , , , 9 6 , , , , E159"??? LEE‘JJ‘EQSI‘IE ,,,,, _________ ETEELJ§€U________9 AT +CUSATE MT - UICC Inlerface Termmal Prome USAT proactive command USAT lermina‘ response # USAT envelope command UICC
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
284
3GPP TS 27.007 version 13.3.0 Release 13
12 Commands for USIM application toolkit
12.1 General
If a UICC connected to an MT uses USIM Application Toolkit (USAT), some USAT features can be provided by the
MT itself, whereas other features can be implemented in the TE. This applies especially to MTs with limited
capabilities, where the user interface could be provided by the TE.
If there are multiple entities inside the TE providing USAT services, for the purpose of this specification, the TE is
visible as one entity handling AT commands and responses on the interface to the TA/MT, see figure 12.1-1.
Figure 12.1-1: Overview of the interfaces between TE, TA/MT and UICC for USAT
The AT commands for definition of the USAT profiles and transmission of USAT proactive commands, USAT terminal
responses and USAT envelope commands between the TE and UICC are specified in the subsequent subclauses.
Compared to APDUs, where the MT is the initiator, USAT defines logic where the UICC is the initiator of the USAT
proactive commands and the MT sends responses to these commands. Due to that, USAT proactive commands are sent
in unsolicited result codes, whereas the associated responses are transported in subsequent AT commands.
12.2 Commands specific to MTs supporting USAT
12.2.1 Read USAT profile +CUSATR
Table 12.2.1-1: +CUSATR action command syntax
Command
Possible response(s)
+CUSATR[=<profile_storage>] [+CUSATR: <profile_storage>,<profile>]
[<CR><LF>+CUSATR: <profile_storage>,<profile>
[...]]
+CME ERROR: <err>
+CUSATR=? +CUSATR: (list of supported <profile_storage>s)
Execution command +CUSATR=<profile_storage> returns the profile specified by <profile_storage>.
Execution command issued without parameter; +CUSATR, returns all profiles.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
285
3GPP TS 27.007 version 13.3.0 Release 13
Test command returns values supported as a compound value.
Refer subclause 9.2 for possible <err> values.
Defined values
<profile_storage>: integer type.
0 TE profile that can be set with +CUSATW.
1 MT profile that can be set with +CUSATW.
2 MT default profile that reflects the inherent, default supported facilities of the MT.
3 UICC profile that reflects the currently active UICC profile that was sent to the UICC in the last TERMINAL
PROFILE command.
4 UICC EF
UST
. The elementary file that indicates services available in the USIM.
5 List of MT only facilities (facilities that are not allowed to be assigned to the TE, see 3GPP TS 31.111 [92]).
<profile>: string type in hexadecimal character format. The profile describing the supported facilities of the
referenced <profile_storage> as specified for the Terminal Profile in 3GPP TS 31.111 [92] or for the
related EF in 3GPP TS 31.102 [59].
Implementation
Optional.
12.2.2 Write USAT profile +CUSATW
Table 12.2.2-1: +CUSATW action command syntax
Command
Possible response(s)
+CUSATW[=<profile_storage>[,<pr
ofile>]] +CUSATW: <profile_storage>,<conflict_profile>
+CME ERROR: <err>
+CUSATW=? +CUSATW: (list of supported <profile_storage>s)
Description
Execution command without parameters resets stored TE and MT profiles to their default values. Adding parameter
<profile_storage> to the AT command resets only the referred storage to its default value. Execution command
issued with accompanied parameter <profile>, stores the given <profile> to non-volatile memory in the MT.
Upon an attempt to store or reset a profile that conflicts with an already stored profile or the list of MT only facilities,
the operation fails and the profile referred to by command parameter <profile_storage> remains unchanged. The
MT responds with +CUSATW: <profile_storage>,<conflict_profile> where <profile_storage>
refers the conflicting profile followed by the final result code +CME ERROR: 3 (Operation not allowed). If there is a
conflict with the MT only facilities, <profile_storage> is set to 5; otherwise <profile_storage> indicates
the profile already stored for the TE or for the MT. The rules for detecting conflicts are defined in
3GPP TS 31.111 [92].
Successful execution of the command does not result in any information response.
Test command returns supported values as a compound value.
Refer subclause 9.2 for possible <err> values.
Defined values
<profile_storage>: integer type.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
286
3GPP TS 27.007 version 13.3.0 Release 13
0 TE. Refers profile storage for the facilities supported by the TE. Default value is a blank profile with all bits
set to zero. This value is applicable both in the execution command and in the information response.
1 MT. Refers profile storage for the facilities to be supported by MT, which can be a subset of the default MT
facilities. The TE can choose to register a subset of the MT default profile, typically omitting facilities also
supported by the TE profile. Default value is the MT default profile. This value is applicable both in the
execution command and in the information response.
5 Refers to a conflict between the TE profile and the list of MT only facilities. This value is not applicable in
the execution command.
<profile>: string type in hexadecimal character format. The profile describing the supported USAT facilities of
the referenced <profile_storage> as specified for the Terminal Profile in 3GPP TS 31.111 [92].
<conflict_profile>: string type in hexadecimal character format. A bitwise AND of two profiles, showing
the conflicts, that is, USAT facilities supported by both profiles. See description of Terminal Profile in
3GPP TS 31.111 [92].
Implementation
Optional.
12.2.3 Profile download upon start-up +CUSATD
Table 12.2.3-1: +CUSATD parameter command syntax
Command
Possible response(s)
+CUSATD=[<download>
[,<reporting>]] +CME ERROR: <err>
+CUSATD? +CUSATD: <download>,<reporting>
+CUSATD=? +CUSATD: (list of supported <download>s),(list of
supported <reporting>s)
Description
This command determines if, and optionally which profile should be downloaded to the UICC automatically upon start-
up. If, prior to a restart/start-up, the +CUSATD settings have not been altered, then the default settings determine the
behaviour upon start-up. However, if the parameters of +CUSATD has been set to other than default and then a restart is
performed (e.g. by +CFUN), these values determine the behaviour. This is true for one restart only after altering
+CUSATD parameters as they are always reset to default at the end of the next UICC start-up (i.e. when the USIM
initialisation as specified in 3GPP TS 31.102 [98] has been completed).
The command without parameters resets the parameters to their default values.
The command can only be used if the UICC is already in active state (<UICC_state> 4, e.g. upon +CUSATA) or in
download completed state (<UICC_state> 2) and the UICC does not support the "Additional TERMINAL PROFILE
after UICC activation" feature (see 3GPP TS 31.111 [92]). In all other cases the command responds with +CME
ERROR: 14 (SIM busy).
+CUSATD=<download>,1 also enables the unsolicited result code +CUSATS: <UICC_state>. The MT uses this
unsolicited result code to indicate that a profile download is performed (setting +CUSATD=0,1 or +CUSATD=1,1) or
that it is ready for profile download (setting +CUSATD=2,1). In both cases, the MT also indicates the end of UICC
start-up by the unsolicited result code +CUSATS: 4. If the UICC is awaiting PIN verification during start-up, this is
also reported.
When using +CUSATD=1, the +CUSATA=1 command has to be used to enable TE profile facility handling after restart.
In the time between profile download and issuance of +CUSATA=1, the UICC may already attempt to issue proactive
commands. The MT will not send these to the TE, but rather give the UICC the response "terminal currently unable to
process command" autonomously. The UICC may implement only a limited number of retries, which can potentially
leave USAT in an unwanted state if the +CUSATA=1 command arrives late.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
287
3GPP TS 27.007 version 13.3.0 Release 13
NOTE: Care has to be taken when using +CUSATD=2. If no +CUSATA=2 or +CUSATA=3 is sent during start-
up, USAT is also blocked for the MT.
Test command returns supported values as compound values.
Refer subclause 9.2 for possible <err> values.
Defined values
<download>: integer type. Parameter decides when/if to perform a profile download to UICC and which profile to
download. The default value is implementation specific.
0 Download MT default profile automatically during next start-up.
1 Download the combined TE and MT profile (merger of the profiles written by +CUSATW) automatically
during next start-up. The rules for merging profiles are defined in 3GPP TS 31.111 [92].
2 Halt next UICC start-up when ready for profile download. Profile to download will be selected and download
will be triggered by +CUSATA.
<reporting>: integer type. Parameter enables unsolicited result code +CUSATS: <UICC_state> to notify the
TE about a new state during start-up.
0 Disable +CUSATS, i.e. no notification.
1 Enable +CUSATS, i.e. notify TE.
<UICC_state>: integer type. Parameter reports that the UICC entered a new state during start-up or that the
UICC ended startup and entered active state.
0 UICC start-up in progress, before profile download.
1 UICC start-up halted and ready for profile download. This state is reached if +CUSATD=2 was issued before
restart. UICC start-up will continue upon +CUSATA=2 or +CUSATA=3.
2 Profile download completed, UICC startup continuing.
3 UICC awaiting PIN verification.
4 UICC active.
Implementation
Optional.
12.2.4 Activate USAT profile +CUSATA
Table 12.2.4-1: +CUSATA action command syntax
Command
Possible response(s)
+CUSATA[=<activation>] +CUSATA: <UICC_state>[,<additional_profile_supp
ort>]
+CME ERROR: <err>
+CUSATA=? +CUSATA: (list of supported <activation>s)
Description
Execution command +CUSATA retrieves the current UICC state or downloads a profile to the UICC and/or activates
handling of the TE profile facilities.
A positive result upon a +CUSATA=1 or +CUSATA=3 command (also) enables TE profile facility handling via
unsolicited result codes +CUSATP: <proactive_command> and +CUSATEND. The MT uses the unsolicited result
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
288
3GPP TS 27.007 version 13.3.0 Release 13
code +CUSATP: <proactive_command> to forward to the TE proactive commands issued by the UICC. The
unsolicited result code +CUSATEND is issued by the MT when the UICC indicates that the proactive command session
is terminated, i.e. in response to a USAT terminal response, the UICC indicates that no other USAT proactive command
is pending. Lastly, terminal responses to the proactive commands can now be issued with
+CUSATT=<terminal_response> and envelope commands can be issued with
+CUSATE=<envelope_command>.
If the action requested by the +CUSATA command can not be performed, the information response
+CUSATA: <UICC_state>,[<additional_profile_support>] is returned with appropriate values,
followed by the final result code +CME ERROR: 4 (Operation not supported) in case the UICC does not support
USAT at all, or the final result code +CME ERROR: 3 (Operation not allowed) in all other cases.
If the UICC is already in active state and the UICC does not support the "Additional TERMINAL PROFILE after UICC
activation" feature (see 3GPP TS 31.111 [92]), the TE has the option to perform a reset of the UICC or use +CFUN to
get back to an initial non-active UICC state. The +CUSATD command can be used to set profile handling upon the next
restart.
All USAT proactive commands that the MT does not process itself and all terminal responses from the TE are
transparently forwarded by the MT. The routing mechanism for USAT commands supported by both entities is
specified in 3GPP TS 31.111 [92].
Test command returns values supported as a compound value.
Refer subclause 9.2 for possible <err> values.
Defined values
<activation>: integer type.
0 Return status information only, in information response:
+CUSATA: <UICC_state>[,<additional_profile_support>].
1 Enable TE profile facility handling only, no profile download. This action can only be used if the combined
TE and MT profile was downloaded during start-up (setting +CUSATD=1).
2 Download MT default profile.
3 Download the combined TE and MT profile (merger of the profiles written by +CUSATW) an enable TE
profile facility handling. The rules for merging profiles are defined in 3GPP TS 31.111 [92].
<UICC_state>: integer type. Parameter reports that the UICC entered a new state during start-up or that the
UICC ended startup and entered active state.
0 UICC start-up in progress, before profile download.
1 UICC start-up halted and ready for profile download. This state is reached if +CUSATD=2 was issued before
restart. UICC start-up will continue upon +CUSATA=2 or +CUSATA=3.
2 Profile download completed, UICC startup continuing.
3 UICC awaiting PIN verification.
4 UICC active.
<additional_profile_support>: integer type. Indicates whether the UICC supports the "Additional
TERMINAL PROFILE after UICC activation" feature (see 3GPP TS 31.111 [92]). The value may not be
available during early phases of start-up.
0 No support.
1 Supported.
<proactive_command>: string type in hexadecimal character format. Proactive command as defined in
3GPP TS 31.111 [92], consisting of the full BER-TLV data object.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
289
3GPP TS 27.007 version 13.3.0 Release 13
Implementation
Optional.
12.2.5 Send USAT terminal response +CUSATT
Table 12.2.5-1: +CUSATT action command syntax
Command
Possible response(s)
+CUSATT=<terminal_response> +CME ERROR: <err>
+CUSATT=?
Description
Execution command sends a USAT terminal response to the MT as an answer to a preceding USAT proactive command
sent from the UICC with unsolicited result code +CUSATP: <proactive_command> (see +CUSATA command
description).
Refer subclause 9.2 for possible <err> values.
Defined values
<terminal_response>: string type in hexadecimal character format. Terminal response to a proactive
command as defined in 3GPP TS 31.111 [92], consisting of the full BER-TLV data object.
Implementation
Optional.
12.2.6 Send USAT envelope command +CUSATE
Table 12.2.6-1: +CUSATE action command syntax
Command
Possible response(s)
+CUSATE=<envelope_command> +CUSATE: <envelope_response>[,<busy>]
[<CR><LF>+CUSATE2: <sw1>,<sw2>]
+CME ERROR: <err>
+CUSATE=?
Description
Execution command allows the TE to send a USAT envelope command to the MT. If the UICC provides response data
to the command or indicates that USAT is busy, the information response
+CUSATE: <envelope_response>[,<busy>] is returned. A second line of information response
+CUSATE2: <sw1>,<sw2> may be provided if the MT presents the status words provided by the UICC.
Refer subclause 9.2 for possible <err> values.
Defined values
<envelope_command>: string type in hexadecimal character format. Envelope command as defined in
3GPP TS 31.111 [92], consisting of the full BER-TLV data object.
<envelope_response>: string type in hexadecimal character format. Response to the envelope command as
defined in 3GPP TS 31.111 [92], consisting of the full BER-TLV data object. An empty string is provided if the
UICC does not have any response data to provide.
<busy>: integer type.
0 UICC indicated normal ending of the command.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
290
3GPP TS 27.007 version 13.3.0 Release 13
1 UICC responded with USAT is busy, no retry by the MT.
2 UICC responded with USAT is busy even after one or more retries by the MT.
<sw1>: integer type. Status word information from the envelope response returned by the UICC as defined in
ETSI TS 102 221 [60], subclause 10.2. The parameter can be delivered to the TE both in the case of successful
and failed execution of the envelope command.
<sw2>: integer type. For description see <sw1>.
Implementation
Optional.
12.3 Informative examples
These examples provide a sequence of interactions where USAT commands and responses are transmitted in AT
commands. As it would make the examples unreadable, USAT data is not given in its hexadecimal representation
(which is found in 3GPP TS 31.111 [92]), but in abstract textual form. For readability, only a subset of USAT facilities
typically provided in a profile is given in the examples. Resulting or triggering actions on the MT-UICC interface are
also indicated in the examples.
First, the TE reads the MT default profile:
AT+CUSATR=2
+CUSATR: 2,<PLAY TONE, SET UP MENU, DISPLAY TEXT, EVENT MENU SELECTION, ...>
OK
The TE removes some USAT facilities in the MT by writing a new MT profile, which contains those facilities that are
to be handled by the MT:
AT+CUSATW=1,<PLAY TONE, ...>
OK
Now the TE tries to write a TE profile that conflicts with the MT profile. The MT responds with the conflict
information and rejects the command.
AT+CUSATW=0,<PLAY TONE, SET UP MENU, DISPLAY TEXT, EVENT MENU SELECTION, ...>
+CUSATW: 1,<PLAY TONE>
+CME ERROR: 3
The next attempt to write a TE profile is successful and the TE activates the profiles.
AT+CUSATW=0,<SET UP MENU, DISPLAY TEXT, EVENT MENU SELECTION, ...>
OK
AT+CUSATA=3
MT -> UICC: TERMINAL PROFILE
UICC -> ME: proactive command pending
OK
The UICC sends a SET UP MENU proactive command, resulting in the command being transferred to the TE and the
latter confirming it with a terminal response; thereafter the proactive session ends.
UICC -> MT: SET UP MENU
+CUSATP: <SET UP MENU>
AT+CUSATT=<OK>
MT -> UICC: TERMINAL RESPONSE: OK
UICC -> ME: no proactive command pending
OK
+CUSATEND
A selection by the subscriber in the menu results in an ENVELOPE being sent to the MT and forwarded to the UICC.
The UICC responds with the next proactive command DISPLAY TEXT. After the terminal response, the proactive
session ends.
AT+CUSATE=<MENU SELECTION, item=1>
MT -> UICC: ENVELOPE(MENU SELECTION, item=1)
UICC -> ME: proactive command pending
OK
UICC -> MT: DISPLAY TEXT
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
291
3GPP
TS 27.007 version 13.3.0 Release 13
+CUSATP: <DISPLAY TEXT>
AT+CUSATT=<OK>
MT -> UICC: TERMINAL RESPONSE: OK
UICC -> ME: no proactive command pending
OK
+CUSATEND
The TE defines UICC profile download options. The definition is effective for the next UICC start-up.
AT+CUSATD=1,1
OK
The UICC restarts. The MT reports the start-up. During start-up the profile download definition cannot be altered and
the MT responds error code 14 (SIM busy).
+CUSATS: 0
AT+CUSATD=2,1
+CME ERROR: 14
The UICC is awaiting PIN verification. During PIN verification the profile download definition cannot be altered and
the MT responds error code 14 (SIM busy).
+CUSATS: 3
AT+CUSATD=2,1
+CME ERROR: 14
The UICC becomes active and the profile download definition can be changed.
+CUSATS: 4
AT+CUSATD=2,1
OK
The TE enables the downloaded profile.
AT+CUSATA=1
OK
The TE reads the TE profile:
AT+CUSATR=0
+CUSATR: 0,<PLAY TONE, SET UP MENU, DISPLAY TEXT, EVENT MENU SELECTION, ...>
OK
Now the TE tries to write a MT profile that conflicts with the TE profile. The MT responds with the conflict
information and rejects the command.
AT+CUSATW=1,<DISPLAY TEXT, ...>
+CUSATW: 0,<DISPLAY TEXT>
+CME ERROR: 3
The next attempt to write a MT profile is successful.
AT+CUSATW=1,<SET UP MENU, EVENT MENU SELECTION, ...>
OK
The TE reads the List of MT only facilities:
AT+CUSATR=5
+CUSATR: 5,<POLL INTERVAL, POLLING OFF, PROVIDE LOCAL INFORMATION (NMR), ...>
OK
Now the TE tries to write a TE profile that conflicts with the MT only facilities. The MT responds with the conflict
information and rejects the command.
AT+CUSATW=0,<POLL INTERVAL, ...>
+CUSATW: 5,<POLL INTERVAL>
+CME ERROR: 3
The next attempt to write a TE profile is successful.
AT+CUSATW=0,<SET UP MENU, DISPLAY TEXT, EVENT MENU SELECTION, ...>
OK
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
292
3GPP TS 27.007 version 13.3.0 Release 13
13 Commands for enhanced support of dialling
13.1 General
This clause defines commands that a TE may use when dialling. These commands can be used instead of ATD that does
not support dialling of URIs.
Subclause 13.2 defines commands for dialling (direct dialling and dialling from phonebook) as well as hangup of these
calls.
Subclause 13.3 contains relevant examples.
13.2 Commands for dialling
13.2.1 Dial URI +CDU
Table 13.2.1-1: +CDU action command syntax
Command
Possible response(s)
+CDU=<action>[,<URI>[,<client>
[,<mpidx>[,<CLIR_OIR>[,<CUG_po
inter>]]]]]
+CME ERROR: <err>
when <action>=0 and command successful:
[+CDUT: <URI_scheme>[,<client>]
[<CR><LF>+CDUT: <URI_scheme>[,<cli
ent>]]
[...]]
when <action>=1 and command successful:
[+CDU: <ccidx>]
when <action>=1 and command unsuccessful:
[+CDUI: <cause>]
+CDU=? +CDU: (list of supported <URI_scheme>s)
Description
Execution command can be used to dial a URI (with <action>=1) for initiating communication using the specified
communication client with the specified media profile. With <action>=0 the command can query which clients are
supported for the URI types supported.
When the command is used to query the supported URI types (i.e. <action>=0), the URI types are provided by
+CDUT: <URI_scheme>. When the command is used to dial a URI (i.e. <action>=1) and the dialling succeeds
the command is terminated by +CDU: <ccidx> and OK. The parameters <CLIR_OIR> and <CUG_pointer> are
used to set the per call basis values of the supplementary services CLIR / OIR and CUG.
The unsolicited result code +CDUU: <ccidx>,<code> can be subsequently provided to give further basic
information about the call as it progresses. The value of the <ccidx> is kept until the call is released. See command
+CMCCS and unsolicited result code +CMCCSI for provision of additional information about the call setup.
If "Call control by USIM" see 3GPP TS 31.111 [92] subclause 4.5 is activated by the USIM, it is the responsibility of
the communication client to perform any required call control verification according to the procedures defined in
3GPP TS 31.111 [92] subclause 7.3 prior to the execution of the call setup.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
293
3GPP TS 27.007 version 13.3.0 Release 13
When call control by USIM is applicable, the communication client shall perform the call control (for example by using
the Commands for USIM application toolkit, see clause 12) and act upon the result of the call control as follows:
- if call control by USIM performs no modifications to the call request, the call setup shall be executed without
any changes to the data;
- if call control by USIM modifies the call request, the call setup shall be executed using the modified data as
provided by the call control;
- if call control by USIM modifies the call request to a different service, the appropriate AT command(s) for that
service shall be executed; and
- if call control by USIM rejects the call request, the call setup shall not be executed.
If the attempt to dial does not succeed, the command is terminated by ERROR / CME ERROR or +CDUI: <cause>
and OK. Refer subclause 9.2 for possible <err> values.
Test command returns values supported as a compound value.
Defined values
<action>: integer type
0 Query supported communication clients for the supported URI types. Execution command +CDU=0 returns a
line of intermediate result code +CDUT: <URI_scheme>[,<client>] for every supported
<URI_scheme>.
1 Dial <URI> using the indicated communication client with the indicated media profile.
<URI>: string type. URI including the prefix specifying the URI type. The URI may include URI parameters. The
used character set should be the one selected with Select TE Character Set +CSCS.
<CLIR_OIR>: integer type. Indicates per call basis changes provided to the supplementary service CLIR / OIR.
See +CLIR for further information of the related parameters.
0 No per call based changes to CLIR / OIR, the settings with +CLIR apply
1 Restrict the CLI presentation for the current call (CLIR / OIR invocation)
2 Allow CLI presentation for the current call (CLIR / OIR suppression)
<CUG_pointer>: integer type. Indicates per call basis changes provided to the supplementary service closed user
group. See +CECUG for further information of the related parameters.
0 No per call basis changes to CUG
1-n Indicates the CUG index to use for this call. The CUG index and corresponding values used as set with
command +CECUG (enable CUG temporary mode). The maximum value of n is implementation specific.
NOTE 1: 3GPP TS 22.085 [21] indicates that each individual subscriber can be a member of a maximum of 10
CUGs.
<URI_scheme>: string type represented with IRA characters. Parameter identifies supported URI scheme. This
parameter shall not be subject to conventional character conversion as per +CSCS.
"sip" Internet Assigned Number Authority (IANA) registry as per RFC 3969 [113], used with Session
Initiation Protocol (SIP), see RFC 3261 [111].
"tel" Internet Assigned Number Authority (IANA) registry as per RFC 5341 [114], used with SIP, see
RFC 3966 [112].
"urn" Internet Assigned Number Authority (IANA) registry according to RFC 2141 [116], only used with
SIP in combination with a suitable uniform resource name (URN) namespace.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
294
3GPP TS 27.007 version 13.3.0 Release 13
NOTE 2: The URN namespace "service" listed in the Internet Assigned Number Authority (IANA) registry
according to RFC 3406 [117] is an example of a namespace that can be used in SIP in combination with
the URI scheme "urn". Not all top-level service labels listed in the Internet Assigned Number Authority
(IANA) registry according to RFC 5031 [118] need to be supported in combination with the URN
namespace "service".
<client>: integer type. Communication client indication. The default value is implementation specific.
1 MMTel. The UE procedures in 3GPP TS 24.173 [87] apply.
128 – 255 Reserved for vendor specific communication clients.
<mpidx>: integer type. Media profile identification number. The parameter is local to the TE-MT interface. The
range of permitted values (minimum value = 1) is returned by the test form of the command +CDEFMP. When
+CDU is used for dialling (i.e. with <action>=1) this number can be provided to point to a particular media
profile. The provided media profile identification number is the number being returned by +CDEFMP when
defining the media profile. Usage and value of a default media profile is implementation specific.
<ccidx>: integer type. Call identification number as described in 3GPP TS 22.030 [19] subclause 6.5.5.1. This
number can be used in +CHLD command operations. Value range is from 1 to N. N, the maximum number of
simultaneous call control processes is implementation specific.
NOTE 3: When +CMCCS is supported, the call identification number is not reset until the unsolicited result code
+CMCCSI has indicated that the <ccstatus>=1 (Idle).
<code>: string type represented with IRA characters. Cause codes giving main call state information. Intermediate
call status responses can be reported using the unsolicited result code +CMCCSI (see command +CMCCS). This
parameter shall not be subject to conventional character conversion as per +CSCS.
"BUSY" Busy signal detected
"ANSWERED" Remote party has answered and the connection between A and B has
been established
"NO ANSWER" Connection completion timeout
"CONNECTION TERMINATED" The connection is terminated from either the remote party or the
network, or the attempt to establish the call setup is unsussessful
NOTE 4: The cause code "CONNECTION TERMINATED" also covers all other situations where a call is
unsuccessfully terminated. Examples of this are all types of network congestion or lack of radio coverage.
<cause>: integer type. Reason code providing further details why the call setup fails in the terminal before
signalling towards the network is initiated.
0 Outgoing call attempt rejected by (U)SIM/ME, unspecified
1 Outgoing call attempt rejected by barring services in the SIM/ME
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
295
3GPP TS 27.007 version 13.3.0 Release 13
13.2.2 Dial URI from phonebook +CDUP
Table 13.2.2-1: +CDUP action command syntax
Command
Possible
response(s)
+CDUP=<pb_field>,<str>[,<client>
[,<mpidx>[,<storage>]]] +CME ERROR: <err>
when command successful:
[+CDUP: <ccidx>]
+CDUP=?
Description
Execution command dials a URI for initiating communication using the specified communication client with the
specified media profile by referencing either the alphanumeric phonebook field, or the index or entry-number in the
phonebook. Supported clients URI schemes are those returned with +CDU=0. If parameter <storage> is not
included, the relevant phonebook is specified by the current +CPBS setting. If the referenced URI is not found, OK is
returned and nothing is dialled.
+CDUP=0,<str> originates a call to the first URI found in the selected phonebook which has a partial or full match to
<str>. The mechanism to search for the first match through a phonebook is implementation specific. Upon no match
in the selected phonebook, it is manufacturer specific if and what further phonebook memories are searched.
+CDUP=1,<str> originates a call to the URI in memory location <str>, where <str> must contain a decimal
number. The index or entry-number in the phonebook is expressed by <str>.
How the string of digits or the index or entry-number is associated with entries is implementation specific.
The command is terminated by +CDUP: <ccidx> and OK or ERROR / CME ERROR. Refer subclause 9.2 for possible
<err> values.
Defined values
<pb_field>: integer type
0 Refers alphanumeric field of the phonebook. <str> may contain valid characters for alphanumeric field of
the selected phonebook.
1 Refers index or entry-number in the phonebook.
<str>: string type. Valid characters are governed by <pb_field>.
<storage>: string type. Supported values are the same as that supported for <storage> of +CPBS.
<client>: integer type. Communication client indication.
1 MMTel. The UE procedures in 3GPP TS 24.173 [87] apply.
128 – 255 Reserved for vendor specific communication clients.
<mpidx>: integer type. Media profile identification number. The parameter is local to the TE-MT interface. The
range of permitted values (minimum value = 1) is returned by the test form of the command +CDEFMP. The
provided media profile identification number is the number being returned by +CDEFMP when defining the
media profile. Usage and value of a default media profile is implementation specific.
<ccidx>: integer type. Call identification number as described in 3GPP TS 22.030 [19] subclause 6.5.5.1. This
number can be used in +CHLD command operations. Value range is from 1 to N. N, the maximum number of
simultaneous call control processes is implementation specific.
Implementation
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
296
3GPP TS 27.00
7 version 13.3.0 Release 13
Optional.
13.2.3 Hangup of current calls +CHCCS
Table 13.2.3-1: +CHCCS action command syntax
Command
Possible response(s)
+CHCCS=<ccidx>[,<cause>] +CME ERROR: <err>
when <ccidx>=value>0 is inserted and
command successful:
[+CHCCSI: <ccidx>]
when <ccidx>=0 is inserted and command
successful:
[+CHCCSI: <ccidx>
[<CR><LF>+CHCCSI: <ccidx>]
[...]]
+CHCS=?
Description
Execution command causes the TA to initiate hangup and subsequently perform call clearing of the call for which a
<ccidx> was provided when the call was detected in the MT. The parameter <cause> can be added to indicate
particular information on the cause for call clearing. Setting the parameter <cause> to values 2 or 3 is typically
relevant for call clearing before a call has been established (e.g. an incoming or waiting call). The parameter <cause>
is ignored by the lower layers if it is not according to the signalling procedures in question.
A special form of the execution command, +CHCCS=0, causes the TA to initiate hangup and subsequently perform call
clearing of all calls for which a <ccidx> was provided when the call was detected in the MT. The parameter
<cause> will be ignored if <ccidx>=0.
The information text +CHCCSI: <ccidx> is provided for each call where a successful hangup is initiated as result of
the +CHCCS. If no hangup is initiated, no information text is provided before OK is returned.
NOTE 1: The command +CHCCS=0 will initiate hangup of all calls with a <ccid>. This also applies to calls on
hold and call waiting calls.
Refer subclause 9.2 for possible <err> values.
Defined values
<ccidx>: integer type. Call identification number as described in 3GPP TS 22.030 [19] subclause 6.5.5.1. This
number can be used in +CHLD command operations. Value range is from 1 to N. N, the maximum number of
simultaneous call control processes is implementation specific.
NOTE 2: When +CMCCS is supported, the call identification number is not reset until the unsolicited result code
+CMCCSI has indicated that the <ccstatus>=1 (Idle).
<cause>: integer type. Proposed cause value for call clearing.
0 No particular cause indicated
1 Cause "Normal call clearing" (value 16), see 3GPP TS 24.008 [8] table 10.5.123 or BYE request, see
RFC 3261 [111] subclause 15.1
2 Cause "Call rejected" (value 21), see 3GPP TS 24.008 [8] table 10.5.123 or "488 Not Acceptable Here", see
RFC 3261 [111] subclause 21.4.26
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
297
3GPP TS 27.007 version 13.3.0 Release 13
3 Cause "User busy" (value 17), see 3GPP TS 24.008 [8] table 10.5.123 or "486 Busy Here", see
RFC 3261 [111] subclause 21.4.24
Implementation
Mandatory when +CDU is implemented in the TA.
13.2.4 Define media profile +CDEFMP
Table 13.2.4-1: +CDEFMP parameter command syntax
Command
Possible response(s)
+CDEFMP=[<mpidx>][,<SDP_md>] +CME ERROR: <err>
When no <mpidx> but <SDP_md> provided and
command successful:
[+CDEFMP: <mpidx>]
+CDEFMP? [+CDEFMP: <mpidx>,<SDP_md>
[<CR><LF>+CDEFMP: <mpidx>,<SDP_md>
[...]]]
+CDEFMP=? +CDEFMP: (range of supported <mpidx>s)
Description
A media profile is identified by its media profile identification number. A media profile defines an SDP media
description to be used in SDP offers and SDP answers. Media profiles can be used with +CDU and +CDUP when
dialling URIs.
The set command specifies the SDP media description for a media profile identified by the (local) media profile
identification number, <mpidx>. When no <mpidx> value is provided then a new SDP media description is defined
and the media profile"s identification number is returned by the command"s response. When an <mpidx> value is
provided, the definition of the SDP media description identified by the media profile identification number <mpidx> is
replaced with the SDP media description provided by the command.
A special form of the set command, +CDEFMP=<mpidx> causes the SDP media description for the indicated media
profile to become undefined. Further, +CDEFMP= causes the SDP media description for all defined media profiles to
become undefined.
The read command returns a list of all defined media profiles.
The test command returns values supported as a compound value.
Refer subclause 9.2 for possible <err> values.
Defined values
<mpidx>: integer type. Media profile identification number. The parameter is local to the TE-MT interface. The
range of permitted values (minimum value = 1) is returned by the test form of the command. The MT shall use
the indicated SDP media description for the <mpidx> in the initial SDP offer for a call setup.
<SDP_md>: string type represented with IRA characters. SDP media description including media level SDP lines.
This parameter shall not be subject to conventional character conversion as per +CSCS.
This parameter can contain the following types of SDP lines: SDP m-lines, SDP a-lines and partial SDP m-lines.
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
298
3GPP TS 27.007 version 13.3.0 Release 13
The communication client in the MT shall take into account SDP a-line rtpmap and fmtp attributes when
negotiating media. Which other attributes in media level SDP a-lines are taken into account by the
communication client is implementation specific.
Partial SDP m-lines include nothing but a media type.
For every media either an SDP m-line or a partial SDP m-line must be provided.
SDP m-lines indicate that the described media is encoded/decoded outside the MT.
Partial SDP m-lines indicate that the described media is encoded/decoded by the MT. When negotiating media
the MT adds payload information to the partial SDP m-line.
The communication client in the MT shall use the provided SDP line information when negotiating media. The
communication client shall add other SDP lines required for negotiating media.
Informative examples
The MT handles encoding and decoding of audio media, and the TE supports two types of video
media, as described by the following SDP lines:
m=audio
m=video 99 98
a=rtpmap:99 H264/90000
a=fmtp:99 profile-level-id=4D4033
a=rtpmap:98 MP4V-ES/90000
a=fmtp:98 profile-level-id=1
To indicate its support for both audio and video media for an incoming or outgoing call, the TE
uses the following <SDP_md>:
"m=audio\0D\0Am=video 99 98\0D\0Aa=rtpmap:99 H264/90000\0D\0Aa=fmtp:99 profile-level-
id=4D4033\0D\0Aa=rtpmap:98 MP4V-ES/90000\0D\0Aa=fmtp:98 profile-level-id=1"
The TE intends to offer a file transfer over MSRP, as described by the following SDP lines:
m=message 7654 TCP/MSRP *
i=This is my latest picture
a=sendonly
a=accept-types:message/cpim
a=accept-wrapped-types:*
a=path:msrp://atlanta.example.com:7654/jshA7we;tcp
a=file-selector:name:"My cool picture.jpg" type:image/jpeg
When proposing the MSRP file transfer to the remote party, the TE uses the following
<SDP_md>:
"m=message 7654 TCP/MSRP *\0D\0Aa=sendonly\0D\0Aa=accept-
types:message/cpim\0D\0Aa=accept-wrapped-
types:*\0D\0Aa=path:msrp://atlanta.example.com:7654/jshA7we;tcp\0D
\0Aa=file-selector:name:\22My cool picture.jpg\22 type:image/jpeg"
NOTE: The SDP i-line is not provided as part of the <SDP_md> value.
Implementation
Optional.
13.2.5 Control and modify media description +CCMMD
Table 13.2.5-1: +CCMMD parameter command syntax
Command
Possible response(s)
+CCMMD=<ccidx>,<neg_status>[,<SDP_md>]
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
299
3GPP TS 27.007 version 13.3.0 Release 13
+CCMMD?
+CCMMD=?
Description
This command allows control of the media used in a multimedia call. The command can be used to initiate modification
of the media of an ongoing call, to accept / reject incoming changes in media or to accept / reject the media for an
incoming call. Supported media types are typically audio, video and messaging (MSRP).
When <ccidx> matches the index of an ongoing call, the TA/MT will attempt to add or remove media to the call by
triggering an SDP renegotiation over the SIP protocol.
When <neg_status>=1, the set command requests an unconditional change the media of the call to that described
by <SDP_md>.
When <neg_status>=2, the set command proposes a change of media to that described by <SDP_md>, to which
the remote party has to respond before the media of the call is changed. The response from the remote party will be
indicated in a +CMCCSI unsolicited result code. If the remote party accepts the change of media, the <neg_status>
value in +CMCCSI will be set to 3. If the remote party rejects the change of media, <neg_status> will be set to 4. In
both cases the <SDP_md> value in +CMCCSI will describe the currently active media of the call (if any).
If the remote party unconditionally changes the media of the call, this will be indicated in a +CMCCSI unsolicited result
code, with <neg_status>=1 and <SDP_md> containing the updated (and now active) media description.
If the remote party proposes to change the media of an ongoing call, this will be indicated in a +CMCCSI unsolicited
result code, with <neg_status>=2. The set command should be used to respond to the proposal, either accepting it
by setting <neg_status>=3, or rejecting it by setting <neg_status>=4.
When the MT receives an incoming call from a remote party, the +CMCCSI unsolicited result code will be sent to the
TE with <neg_status>=2. This proposed media for the new call should either be accepted, (as described above) or
it should be rejected and a new media should be proposed using the set command with <neg_status>=2.
Defined values
<ccidx>: integer type. Call identification number as defined in the +CMCCS and +CLCCS commands.
<neg_status>: integer type
1 The <SDP_md> parameter describes the desired set of media for the call.
2 The <SDP_md> parameter describes a proposal for a new set of media for the call.
3 Accept the most recently received media proposal. The <SDP_md> parameter describes the accepted media
for the call.
4 Reject the most recently received media proposal.
<SDP_md>: string type represented with IRA characters. Media description as per the +CDEFMP command. This
parameter shall not be subject to conventional character conversion as per +CSCS.
Implementation
Optional.
13.3 Informative examples
Below is an example where a voice call originated with +CDU is placed to a tel-URI. This example outlines how the call
is initiated by the AT command +CDU, and how the unsolicited result code +CDUU is used to indicate how the call-
setup progress until it is terminated. Both successful and unsuccessful outcome of a call attempt is shown in the
example.
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
300
3GPP TS 27.007 version 13.3.0 Release 13
AT+CDU=1,"tel:+47-123-45678" (Voice call initiated)
+CDU: 2 (Call initiated, call identification number 2 provided)
OK (Call initiation successful)
(Call setup progress, unsolicited result codes appear as appropriate)
(If call is answered by the remote party)
+CDUU: 2,"ANSWERED" (Remote party has answered)
(If remote party does not answer)
+CDUU: 2,"NO ANSWER" (Connection completion timeout)
(If remote party is busy)
+CDUU: 2,"BUSY" (Busy signal detected)
(If call is terminated from remote party)
+CDUU: 2,"CONNECTION TERMINATED" (Connection terminated from remote party)
(If call is terminated from calling party)
AT+CHCCS=2 (Connection with call identification number 2 terminated from calling party)
+CHCCSI: 2
OK
Below is an example where a multimedia-call (voice) originated with +CDU is placed to a SIP-URI. This example
outlines how the call is initiated by the AT command +CDU, and how the unsolicited result codes +CDUU and
+CMCCSI are used to indicate how the call-setup progress until it is terminated. A precondition for this example is that
the basic event for the call monitoring function is successfully enabled with +CMCCS=2.
AT+CDU=1,"sip:veronica@university.org" (Multimedia-call (voice) initiated)
+CDU: 4 (Call initiated, call identification number 4 provided)
OK (Call initiation successful)
(+CDUU and +CMCCSI appear as appropriate)
+CMCCSI: 4,0,0,0,"",0,2,0,1,0,"sip:veronica@university.org",0,0 (Call setup is started)
+CMCCSI: 4,0,0,0,"",0,3,0,1,0,"sip:veronica@university.org",0,0 (Call is in progress)
+CMCCSI: 4,0,0,0,"",0,4,0,1,0,"sip:veronica@university.org",0,0 (Alert indication received)
CDUU: 4,"ANSWERED" (Remote party answered)
+CMCCSI: 4,0,0,0,"",0,6,0,1,0,"sip:veronica@university.org",0,0 (Connection established)
AT+CHCCS=4 (Connection with call identification number 4 terminated)
+CHCCSI: 4
OK
+CMCCSI: 4,0,0,0,"",0,7,0,1,0,"sip:veronica@university.org",2,200 (Outgoing connection released)
+CMCCSI: 4,0,0,0,"",0,0,0,1,0,"sip:veronica@university.org",0,0 (Idle)
Below is an example where a multimedia-call originated with +CDU is placed to a SIP-URI. This example outlines how
the call is initiated by the AT command +CDU, and how the unsolicited result codes +CDUU and +CMCCSI are used to
indicate how the call-setup progresses until it is terminated. A precondition for this example is that the basic event for
the call monitoring function is successfully enabled with +CMCCS=2. This example illustrates the use of the +CDEFMP
and +CCMMD commands to define and control the types of media that are used in the call.
AT+CDEFMP=,"m=audio" (Media profile defined, offering only audio)
+CDEFMP=3 (Media profile index number 3 provided)
OK
AT+CDU=1,"sip:veronica@university.org",1,3 (Multimedia-call initiated, using media profile number 3)
+CDU: 5 (Call initiated, call identification number 5 provided)
OK (Call initiation successful)
(+CDUU and +CMCCSI appear as appropriate)
+CMCCSI: 5,0,0,0,"",0,2,0,1,0,"sip:veronica@university.org",0,0 (Call setup is started)
+CMCCSI: 5,0,0,0,"",0,3,0,1,0,"sip:veronica@university.org",0,0 (Call is in progress)
+CMCCSI: 5,0,0,1,"m=audio",0,4,0,1,0,"sip:veronica@university.org",0,0
(Alert indication received and played back)
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
301
3GPP TS 27.007 versio
n 13.3.0 Release 13
+CMCCSI: 5,0,1,3,"m=audio",0,4,0,1,0,"sip:veronica@university.org",0,0
(Remote party accepted the proposal for audio media)
+CDUU: 5,"ANSWERED" (Remote party answered)
+CMCCSI: 5,0,1,1,"m=audio",0,6,0,1,0,"sip:veronica@university.org",0,0
(Connection established, audio media is active)
+CMCCSI: 5,0,1,2,"m=audio\0D\0Am=video 99 98\0D\0Aa=rtpmap:99 H264/90000\0D\0Aa=fmtp:99 profile-
level-id=4D4033\0D\0Aa=rtpmap:98 MP4V-ES/90000\0D\0Aa=fmtp:98 profile-level-
id=1",0,6,0,1,0,"sip:veronica@university.org",0,0
(Remote party proposed adding video to the call, offering two different formats)
AT+CCMDC=5,3,"m=audio\0D\0Am=video 99 98\0D\0Aa=rtpmap:99 H264/90000\0D\0Aa=fmtp:99 profile-level-
id=4D4033\0D\0Aa=rtpmap:98 MP4V-ES/90000\0D\0Aa=fmtp:98 profile-level-id=1"
(Proposal accepted, indicating support for both formats offered)
OK
+CMCCSI: 5,0,1,1,"m=audio\0D\0Am=video 99\0D\0Aa=rtpmap:99 H264/90000\0D\0Aa=fmtp:99 profile-level-
id=4D4033",0,6,0,1,0,"sip:veronica@university.org",0,0
(Call media changed to audio and video on a format selected by the TE)
AT+CCMDC=5,1,"m=audio" (Video media removed, unconditionally)
OK
+CMCCSI: 5,0,1,1,"m=audio",0,6,0,1,0,"sip:veronica@university.org",0,0
(Call media changed to audio only)
AT+CHCCS=5 (Connection with call identification number 5 terminated)
+CHCCSI: 5
OK
+CMCCSI: 5,0,0,0,"",0,7,0,1,0,"sip:veronica@university.org",2,200 (Outgoing connection released)
+CMCCSI: 5,0,0,0,"",0,1,0,1,0,"sip:veronica@university.org",0,0 (Idle)
Below is an example where a multimedia-call originated with +CDU is placed to a SIP-URI. In this example, the remote
party rejects the proposed media and makes a counterproposal, which is then accepted by the originating party before
the call is established. A precondition for this example is that the basic event for the call monitoring function is
successfully enabled with +CMCCS=2. The terms "<Audio>" and "<Audio+video>" are used to illustrate
respective SDP media descriptions of audio and audio+video in the example.
AT+CDEFMP=,"<Audio+video>" (Media profile defined, offering both audio and video)
+CDEFMP=4 (Media profile index number 4 provided)
OK
AT+CDU=1,"sip:veronica@university.org",1,4 (Multimedia-call initiated, using media profile number 4)
+CDU: 6 (Call initiated, call identification number 6 provided)
OK (Call initiation successful)
(+CDUU and +CMCCSI appear as appropriate)
+CMCCSI: 6,0,0,0,"",0,2,0,1,0,"sip:veronica@university.org",0,0 (Call setup is started)
+CMCCSI: 6,0,0,0,"",0,3,0,1,0,"sip:veronica@university.org",0,0 (Call is in progress)
+CMCCSI: 6,0,0,1,"<Audio>",0,4,0,1,0,"sip:veronica@university.org",0,0
(Alert indication received and played back)
+CMCCSI: 6,0,1,4,"",0,4,0,1,0,"sip:veronica@university.org",0,0
(Remote party rejected the proposal for audio+video media)
+CMCCSI: 6,0,1,2,"<Audio>",0,4,0,1,0,"sip:veronica@university.org",0,0
(Remote party proposed audio-only media for the call)
AT+CCMMD=6,3,"<Audio>" (Proposal accepted)
OK
+CDUU: 6,"ANSWERED" (Remote party answered the call)
+CMCCSI: 6,0,1,1,"<Audio>",0,6,0,1,0,"sip:veronica@university.org",0,0
(Connection established, audio media is active)
Below is the same scenario as above from the terminating party's perspective. An incoming multimedia-call is received,
but the initially offered media is rejected and a successful counterproposal is made. A precondition for this example is
that the basic event for the call monitoring function is successfully enabled with +CMCCS=2. The terms "<Audio>"
13
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
302
3GPP TS 27.007 version 13.3.0 Release 13
and "<Audio+video>" are used to illustrate respective SDP media descriptions of audio and audio+video in the
example.
RING (Ringing call)
+CMCCSI: 3,1,1,2,"<Audio+video>",0,5,0,1,0,"sip:archie@university.org",0,0
(Incoming ringing call with call identification number 3 and a proposal for audio+video media)
AT+CCMMD=3,4 (Media proposal rejected)
OK
AT+CCMMD=3,2,"<Audio>" (Audio-only media for the call proposed)
OK
+CMCCSI: 3,1,1,3,"<Audio>",0,5,0,1,0,"sip:archie@university.org",0,0
(Originating party accepted the proposed, and now active, audio media)
ATA (Call answered)
OK
+CMCCSI: 3,1,1,1,"<Audio>",0,6,0,1,0,"sip:archie@university.org",0,0 (Active call established with audio media)
Below is an example where a multimedia-call originated with +CDU is placed to a SIP-URI. In this example, both the
proposed media and the call is rejected by the remote party. A precondition for this example is that the basic event for
the call monitoring function is successfully enabled with +CMCCS=2. The terms "<Audio>" and
"<Audio+video>" are used to illustrate SDP media description of audio and audio+video in the example.
AT+CDEFMP=,"<Audio+video>" (Media profile defined, offering both audio and video)
+CDEFMP=5 (Media profile index number 5 provided)
OK
AT+CDU=1,"sip:veronica@university.org",1,5 (Multimedia-call initiated, using media profile number 5)
+CDU: 7 (Call initiated, call identification number 7 provided)
OK (Call initiation successful)
(+CDUU and +CMCCSI appear as appropriate)
+CMCCSI: 7,0,0,0,"",0,2,0,1,0,"sip:veronica@university.org",0,0 (Call setup is started)
+CMCCSI: 7,0,0,0,"",0,3,0,1,0,"sip:veronica@university.org",0,0 (Call is in progress)
+CMCCSI: 7,0,0,1,"<Audio>",0,4,0,1,0,"sip:veronica@university.org",0,0
(Alert indication received and played back)
+CMCCSI: 7,0,1,4,"",0,4,0,1,0,"sip:veronica@university.org",0,0
(Remote party rejected the proposal for audio+video media)
+CDUU: 7,"CONNECTION TERMINATED" (Remote party rejected the call)
+CMCCSI: 7,0,0,0,"",0,7,0,1,0,"sip:veronica@university.org",2,488 (Outgoing connection released)
+CMCCSI: 7,0,0,0,"",0,1,0,1,0,"sip:veronica@university.org",0,0 (Idle)
Below is the same scenario as above from the terminating party's perspective. An incoming multimedia-call is received,
but both the initially offered media and the call are rejected. A precondition for this example is that the basic event for
the call monitoring function is successfully enabled with +CMCCS=2. The term "<Audio+video>" is used to
illustrate SDP media description of audio+video in the example.
RING (Ringing call)
+CMCCSI: 4,1,1,2,"<Audio+video>",0,5,0,1,0,"sip:archie@university.org",0,0
(Incoming ringing call with call identification number 4 and a proposal for audio+video media)
AT+CCMMD=4,4 (Media proposal rejected)
OK
AT+CHCCS=4,2 (Connection with identification number 4 rejected)
+CHCCSI: 4
OK
+CMCCSI: 4,0,0,0,"",0,8,0,1,0,"sip:veronica@university.org",2,488 (Incoming connection released)
+CMCCSI: 4,0,0,0,"",0,1,0,1,0,"sip:veronica@university.org",0,0 (Idle)
ETSI
ETSI TS 1
27 007 V13.3.0 (2016
-
03)
303
3GPP TS 27.007 version 13.3.0 Release 13
14 Commands for eMBMS configuration
14.1 General
This clause defines AT commands that a TE may use to control MT supporting evolved Multimedia Broadcast
Multicast Service (eMBMS). eMBMS is a unidirectional point-to-multipoint service in which data is transmitted from a
single source entity to a group of users in a specific area. eMBMS services are transmitted on the same carrier
frequencies used by mobile operators to provide other typical services such as voice calls and internet. There are various
types of eMBMS services that can be provided to the end user such as Mobile TV, streaming, file download, etc.
eMBMS information is sent over SystemInformationBlockType13 information element (SIB-13) according to
3GPP TS 36.331 [86] subclause 6.3.1. Information on eMBMS parameters can be found in 3GPP TS 36.443 [150] and
3GPP TS 29.061 [39].
A comprehensive set of eMBMS-specific commands is defined to provide the flexibility needed by the more complex
MT. The commands are designed to be expandable to accommodate new eMBMS feature options and interface
protocols, merely by defining new values for many of the parameters. The commands use the extended information and
error message capabilities described in this specification.
The +CEMBMSCFG command enables or disables the eMBMS support in the MT. Once the eMBMS service is enabled
then the status of the eMBMS session can be received by enabling the URC using the +CEMBSR command. The
+CEMBSR command also provides information about the TMGI and eMBMS session being used by the MT. The
+CEMBMSDATA command can be used by the MT to configure the data channel to use for receiving eMBMS services.
The +CEMBMSSRV command is used to configure and activate the eMBMS service for a specific TMGI and listen for
any service change indications. The +CEMBMSCNT command can be used to set the list of TMGIs from which the MT
can receive eMBMS services.
14.2 Commands specific to eMBMS
14.2.1 eMBMS configuration in MT +CEMBMSCFG
Table 14.2.1-1: +CEMBMSCFG parameter command syntax
Command
Possible response(s)
+CEMBMSCFG=<setup_cfg> +CME ERROR: <err>
+CEMBMSCFG? +CEMBMSCFG: <setup_cfg>
+CEMBMSCFG=? +CEMBMSCFG: (list of supported <setup_cfg>s)
Description
Set command enables and disables the eMBMS support.
When eMBMS is enabled the MT reads the SystemInformationBlockType13 information element (SIB-13) according
to 3GPP TS 36.331 [86] subclause 6.3.1.
If this command is issued when eMBMS is not active, +CME ERROR is returned. Refer to subclause 9.2 for possible
<err> values.
Read command returns the current eMBMS configuration settings in the MT.
Test command returns values supported as a compound value.
Defined values
<setup_cfg>: integer type; specifies if eMBMS support is to be enabled or disabled in the MT.
0 disable eMBMS support in MT. When eMBMS support is disabled MT is not receiving or consuming any
eMBMS service nor monitoring any Multicast Control Channel
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
304
3GPP TS 27.007 version 13.3.0 Release 13
1 enable eMBMS support in MT
Implementation
Optional
14.2.2 eMBMS status reporting in MT +CEMBMSR
Table 14.2.2-1: +CEMBMSR parameter command syntax
Command
Possible response(s)
+CEMBMSR=[<n>]
+CEMBMSR? +CEMBMSR: <n>
+CEMBMSR=? +CEMBMSR: (list of supported <n>s)
Description
Set command controls the presentation of unsolicited result code
+CEMBMSRI: <session_status>,<tmgi>,<embms_session_id>[,<tmgi>,<embms_session_id>
[…]] reporting eMBMS session parameter values. The eMBMS session parameter values are reported only if the
eMBMS service is enabled using the +CEMBMSCFG command. Set command does not trigger a request in the MT to
read the SystemInformationBlockType13 information element (SIB-13) information.
Read command returns the current eMBMS unsolicited result code settings in the MT.
Test command returns values supported as a compound value.
Defined values
<n>: integer type
0 disable presentation of the unsolicited result code
1 enable presentation of the unsolicited result code
+CEMBMSRI: <session_status>,<tmgi>,<embms_session_id>[,<tmgi>,<embms_sess
ion_id>[…]]
<session_status>: integer type; if eMBMS support is enabled, this parameter indicates whether an eMBMS
session is activated or deactivated. When the eMBMS session is activated, +CEMBMSDATA command can be
used to enter into data state.
0 eMBMS session is deactivated. When eMBMS session is deactivated MT is not receiving or consuming any
eMBMS service but the MT is monitoring Multicast Control Channels
1 eMBMS session is activated
<tmgi>: string type in hex format; value is the Temporary Mobile Group Identity allocated to a particular eMBMS
bearer service. Refer 3GPP TS 24.008 [8], subclause 10.5.6.13.
<embms_session_id>: integer type; value is the eMBMS Session Identity, which together with TMGI
identifies a specific eMBMS session. Refer 3GPP TS 29.061 [39], subclause 17.7.11.
Implementation
Optional
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
305
3GPP TS 27.007 version 13.3.0 Release 13
14.2.3 eMBMS service configuration +CEMBMSSRV
Table 14.2.3-1: + CEMBMSSRV parameter command syntax
Command
Possible response(s)
+CEMBMSSRV=[<n>[,<embms_service>[
,<tmgi>]]] [+CEMBMSSRV: <service_type>,<no
_services_info>,<tmgi>[,<embms
_session_id>[,<tmgi>[,<embms_s
ession_id>[…]]]]
[<CR><LF>[+CEMBMSSRV:<service_
type>,<no_services_info>,<tmgi
>[,<embms_session_id>[,<tmgi>[
,<embms_session_id>[…]]]]]
[…]]]]]
+CME ERROR:<err>
+CEMBMSSRV? +CEMBMSSRV:<n>
+CEMBMSSRV=? +CEMBMSSRV: (list of supported
<n>s),(list of supported
<embms_service>s)
Set command is used for querying and listening for service change indications and to control the presentation of
following unsolicited service result code in the terminal
+CEMBMSSRVI: <service_type>,<no_services_info>,<tmgi>[,<embms_session_id>[,<tmgi
>[,<embms_session_id>[…]]]] reporting eMBMS service information TMGI and eMBMS Session Identity.
If this command is issued when eMBMS is not active, +CME ERROR is returned. Refer to subclause 9.2 for possible
<err> values.
Read command returns the result code settings of the terminal.
Test command returns values supported as a compound value.
Defined values
<n>: integer type; provides an option to control the unsolicited presentation on TE/MT.
0 disable eMBMS unsolicited result code
1 enable eMBMS unsolicited result code
<embms_service>: integer type; provides an option to query and configure eMBMS services. The MT should
use the value 4 as the default value.
0 query eMBMS services available for use by the MT
1 query eMBMS services being used by the MT
2 configure eMBMS service for use by the MT
3 deconfigure eMBMS service for use by the MT
4 keep current configuration of eMBMS services used by the MT
<service_type>: integer type; indicates whether the eMBMS service is available for use or is being used by
the mobile
0 eMBMS service available for use by the MT
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
306
3GPP TS 27.007 version 13.3.0
Release 13
1 eMBMS service being used by the MT
<no_services_info>: integer type; number of eMBMS services for which information is reported for a
particular <service_type>
<tmgi>: string type in hex format; value is the Temporary Mobile Group Identity allocated to a particular
eMBMS bearer service. Refer 3GPP TS 24.008 [8], subclause 10.5.6.13.
<embms_session_id>: integer type; value is the optional MBMS Session Identity, which together with TMGI
identifies a specific MBMS session. Refer 3GPP TS 29.061 [39], subclause 17.7.11.
Implementation
Optional
14.2.4 Enter eMBMS data state +CEMBMSDATA
Table 14.2.4-1: +CEMBMSDATA parameter command syntax
Command
Possible response(s)
+CEMBMSDATA=<embms_session_id> +CME ERROR: <err>
+CEMBMSDATA=?
Description
Set command is used to enter eMBMS data state by configuring the channel for data transfer for the specified eMBMS
session. MT does not process any further AT commands after entering the eMBMS data state. The MT exits the
eMBMS data state once the eMBMS data transfer is complete or the eMBMS session becomes inactive.
If this command is issued when eMBMS is not active, +CME ERROR is returned. Refer to subclause 9.2 for possible
<err> values.
Defined values
<embms_session_id>: integer type; value is the eMBMS Session Identity, which together with TMGI
identifies a specific eMBMS session. Refer 3GPP TS 29.061 [39], subclause 17.7.11.
Implementation
Optional
14.2.5 eMBMS counting procedure +CEMBMSCNT
Table 14.2.5-1: +CEMBMSCNT parameter command syntax
Command
Possible response(s)
CEMBMSCNT=<tmgi>[,<tmgi>[,…]] +CME ERROR: <err>
CEMBMSCNT? +CEMBMSCNT: <tmgi>,[,<tmgi>[,…]]
CEMBMSCNT=?
Description
Set command is used to set the list of TMGIs for which the user is interested in receiving eMBMS services. Refer to
3GPP TS 36.331 [86] subclause 5.8.4.1 for MBMS Counting Procedure.
If this command is issued when eMBMS is not active, +CME ERROR is returned. Refer to subclause 9.2 for possible
<err> values.
Read command is used to get the list of TMGI"s from which the user is interested in receiving eMBMS services.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
307
3GPP TS 27.007 version 13.3.0 Release 13
Defined values
<tmgi>: string type in hex format; value is the Temporary Mobile Group Identity allocated to a particular eMBMS
bearer service. Refer 3GPP TS 24.008 [8], subclause 10.5.6.13.
Implementation
Optional
14.2.6 eMBMS Service Area Identities +CEMBMSSAI
Table 14.2.6-1: +CEMBMSSAI parameter command syntax
Command
Possible response(s)
+CEMBMSSAI=[<n>[,<embms_
priority_flag>]] +CME ERROR: <err>
+CEMBMSSAI? +CEMBMSSAI: USERDEF <n>,<embms_priority_flag>
,<earfcn_cnt>[,<earfcn>[,<earfcn>[,…]]]
+CEMBMSSAI: FCNT <embms_priority_flag>,<inter
_frequency_cnt>
+CEMBMSSAI: INTER <earfcn>,<sai_cnt>[,<sai>[,
<sai>[,…]]]
+CEMBMSSAI: INTRA <sai_cnt>,<sai>[,<sai>[,…]]
+CEMBMSSAI=? +CEMBMSSAI: (list of supported <n>s),(list of supported
<embms_priority_flag>s)
Set command sets the priority of eMBMS reception over unicast reception. When <n=1>, unsolicited result codes
report the SAI of the current and the neighboring carrier frequencies provided by the network through
SystemInformationBlockType15 (SIB-15) according to 3GPP TS 36.331 [86] subclause 6.3.1.
The unsolicited result code +CEMBMSSAII: FCNT <embms_priority_flag>,<inter_frequency_cnt>
reports the priority of eMBMS reception over unicast reception and the number of neighboring frequencies that provide
eMBMS services.
The unsolicited result code +CEMBMSSAII: INTER <earfcn>,<sai_cnt>[,<sai>[,<sai>[,…]]]
reports the SAI in the neighboring frequencies.
The unsolicited result code +CEMBMSSAII: INTRA <sai_cnt>,<sai>[,<sai>[,…]] reports the SAI in the
current frequency.
If this command is issued when eMBMS is not active, +CME ERROR is returned. Refer subclause 9.2 for possible
<err> values.
Read command returns the current settings of <n> and <embms_priority_flag> in the MT.
Test command returns values supported as compound values.
Defined values
<n>: integer type; provides an option to control the unsolicited presentation on TE/MT.
0 disable eMBMS unsolicited result code
1 enable eMBMS unsolicited result code
<embms_priority_flag>: integer type; indicates the priority of eMBMS reception over unicast reception.
0 the unicast reception shall have priority over eMBMS reception
1 the eMBMS reception shall have priority over unicast reception
13
ETSI
ETSI TS 127 007 V
13.3.0 (2016
-
03)
308
3GPP TS 27.007 version 13.3.0 Release 13
<earfcn>: integer type; indicates the eMBMS frequency the user is interested to receive. It"s the carrier frequency
of the LTE cell designated by the EUTRA Absolute Radio Frequency Channel Number (EARFCN) , valid range:
0...0xFFFF (refer 3GPP TS 36.101 [154], subclause 5.7.3).
<earfcn_cnt>: integer type; indicates the count of <earfcn> reported. The maximum possible value is 32.
<inter_frequency_cnt>: integer type; indicates the number of inter frequencies that will be reported.
<sai>: integer type; indicates the SAI in corresponding downlink carrier frequencies.
<sai_cnt>: integer type; indicates the count of <sai> being reported. The maximum value is 128.
Implementation
Optional.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
309
3GPP TS 27.007 version 13.3.0 Release 13
Annex A (normative):
Summary of commands from other standards
Summary of ITU-T Recommendation V.250 [14] commands applicable to GSM/UMTS:
Table A.1: V.250 commands applicable to GSM/UMTS
Name
V.250
subclause
Description
S
ubclauses in the
present document
&C 6.2.8 Circuit 109 (Received line signal detector) Behaviour 4.3
&D 6.2.9 Circuit 108 (Data terminal ready) Behaviour 4.3
&F 6.1.2 Set to Factory-defined Configuration 5.8/ 3
+DR 6.6.2 Data Compression Reporting 6.20
+DS 6.6.1 Data Compression 6.20
+GCAP 6.1.9 Request Complete Capabilities List 5.8
+GCI 6.1.10 Country of Installation 5.8
+GMI 6.14 Request Manufacturer Identification 5.8/ 5.1
+GMM 6.1.5 Request Model Identification 5.8/ 5.2
+GMR 6.1.6 Request Revision Identification 5.8/ 5.3
+GOI 6.1.8 Request Global Object Identification 5.8
+GSN 6.1.7 Request Product Serial Number Identification 5.8/ 5.4
+ICF 6.2.11 DTE-DCE Character Framing 4.3
+IFC 6.2.12 DTE-DCE Local Flow Control 4.3
+ILRR 6.2.13 DTE-DCE Local Rate Reporting 4.3
+IPR 6.2.10 Fixed DTE Rate 4.3
A 6.3.5 Answer 6.19/ 6.6
D 6.3.1 Dial 6.1-6.4/ 6.6
E 6.2.4 Command Echo 4.3
H 6.3.6 Hook Control 6.19/ 6.5/ 6.6
I 6.1.3 Request Identification Information 5.8
L 6.3.13 Monitor Speaker Loudness 6.19
M 6.3.14 Monitor Speaker Mode 6.19
O 6.3.7 Return to Online Data State 6.19
P 6.3.3 Select Pulse Dialling 6.19
Q 6.2.5 Result Code Suppression 4.3
S0 6.3.8 Automatic Answer 6.19
S10 6.3.12 Automatic Disconnect Delay 6.19
S3 6.2.1 Command Line Termination Character 4.3
S4 6.2.2 Response Formatting Character 4.3
S5 6.2.3 Command Line Editing Character 4.3
S6 6.3.9 Pause Before Blind Dialling 6.19
S7 6.3.10 Connection Completion Timeout 6.19
S8 6.3.11 Comma Dial Modifier Time 6.19
T 6.3.2 Select Tone Dialling 6.19
V 6.2.6 DCE Response Format 4.3/ 3/ 4.1/ 4.2
X 6.2.7 Result Code Selection and Call Progress Monitoring Control 4.3
Z 6.1.1 Reset To Default Configuration 5.8
The use of ITU-T Recommendation V.42 error control protocol is not specified for GSM/UMTS, but if a manufacturer
chooses to implement it over transparent data service, +E prefixed commands of ITU-T Recommendation V.250 [14]
shall be used.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
310
3GPP TS 27.007 version 13.3.0 Release 13
ITU-T Recommendation T.31 [11] and ITU-T Recommendation T.32 [12] may be used as facsimile TA-TE protocols
without deletions or additions to the command set.
TIA IS-99 [15] commands referenced in the present document:
Table A.2: TIA IS-99 commands in the present document
Command
IS
-
99
subclause
Descripti
on
Subclause in
the present
document
+CBC 5.6.5 Battery Charge 8.4
+CGMI 5.6.10 Request Manufacturer Identification 5.1
+CGMM 5.6.10 Request Model Identification 5.2
+CGMR 5.6.10 Request Revision Identification 5.3
+CGSN 5.6.10 Request Product Serial Number Identification 5.4
+CRC 5.6.7 Cellular Result Codes 6.11
TIA IS-135 [16] commands referenced in the present document:
Table A.3: TIA IS-135 commands in the present document
Command
IS
-
135
subclause
Description
Subclause in
the present
document
+CBC 4.1.24 Battery Charge 8.4
+CRC 4.1.29 Cellular Result Codes 6.11
+CSQ 4.1.31 Signal Quality 8.5
PCCA STD-101 [17] commands referenced in the present document:
Table A.4: PCCA STD-101 commands in the present document
Command
STD
-
101
subclause
Description
Subclause in
the present
document
+WS46
5.2.4.6 WDS-side Stack Selection 5.9
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
311
3GPP TS 27.007 version 13.3.0 Release
13
Annex B (normative):
Summary of result codes
ITU-T Recommendation V.250 [14] result codes which can be used in GSM/UMTS and result codes defined in the
present document:
Table B.1: Result codes
Verbose result code
(V.250 command V1 set)
Numeric
(V0 set)
Type
Description
+CACSP as verbose unsolicited refer subclause 11.1.7
+CALV as verbose unsolicited refer subclause 8.16
+CANCHEV as verbose unsolicited refer subclause 11.1.8
+CAPTT as verbose unsolicited refer subclause 11.1.4
+CAULEV as verbose unsolicited refer subclause 11.1.5
+CBCAP as verbose unsolicited refer subclause 8.59
+CBCHG as verbose unsolicited refer subclause 8.61
+CBCON as verbose unsolicited refer subclause 8.60
+CCCM as verbose unsolicited refer subclause 7.16
+CCSFBU as verbose unsolicited refer subclause 8.76
+CCWA as verbose unsolicited refer subclause 7.12
+CCWV as verbose unsolicited refer subclause 8.28
+CDEV as verbose unsolicited refer subclause 8.10
+CDIP as verbose unsolicited refer subclause 7.9
+CDUU as verbose unsolicited refer subclause 13.2.1
+CEMBMSRI as verbose unsolicited refer subclause 14.2.2
+CEMBMSSAII as verbose unsolicited refer subclause 14.2.6
+CEMBMSSRVI as verbose unsolicited refer subclause 14.2.3
+CEPTT as verbose unsolicited refer subclause 11.1.10
+CEREG as verbose unsolicited refer subclause 10.1.22
+CPNERU as verbose unsolicited refer subclause 8.70
+CGDEL as verbose intermediate refer subclause 10.1.29
+CGEV as verbose unsolicited refer subclause 10.1.19
+CGREG as verbose unsolicited refer subclause 10.1.20
+CHSR as verbose intermediate refer subclause 6.16
+CIEV as verbose unsolicited refer subclause 8.10
+CIREGU as verbose unsolicited refer subclause 8.71
+CIREPH as verbose unsolicited refer subclause 8.64
+CIREPI as verbose unsolicited refer subclause 8.64
+CKEV as verbose unsolicited refer subclause 8.10
+CLAV as verbose unsolicited refer subclause 8.31
+CLIP as verbose unsolicited refer subclause 7.6
+CMCCSI as verbose unsolicited refer subclause 7.73
+CMCCSS<x> as verbose unsolicited refer subclause 7.74
+CMCCSSEND as verbose unsolicited refer subclause 7.74
+CME ERROR as verbose final refer subclause 9.2.0
+CMOLRE as verbose unsolicited refer subclause 9.3.1
+CMOLRG as verbose unsolicited refer subclause 8.50
+CMOLRN as verbose unsolicited refer subclause 8.50
+CMTLR as verbose unsolicited refer subclause 8.57
+CMWN as verbose unsolicited refer subclause 7.36
+CNAP as verbose intermediate
unsolicited refer subclause 7.30
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
312
3GPP TS 27.007 version 13.3.0 Release 13
+CNEC_MM as verbose unsolicited refer subclause 9.1b
+CNEC_GMM as verbose unsolicited refer subclause 9.1b
+CNEC_GSM as verbose unsolicited refer subclause 9.1b
+CNEC_EMM as verbose unsolicited refer subclause 9.1b
+CNEC_ESM as verbose unsolicited refer subclause 9.1b
+CNEMIU as verbose unsolicited refer subclause 7.33
+CNEMS1 as verbose unsolicited refer subclause 7.33
+COEV as verbose unsolicited refer subclause 8.10
+COLP as verbose intermediate
unsolicited refer subclause 7.8
+CPOSR as verbose unsolicited refer subclause 8.56
+CPNSTAT as verbose unsolicited refer subclause 7.28
+CPSB as verbose unsolicited refer subclause 7.29
+CR as verbose intermediate refer subclause 6.9
+CREG as verbose unsolicited refer subclause 7.2
+CRING as verbose unsolicited refer subclause 6.11
+CSCON as verbose unsolicited refer subclause 10.1.30
+CSSI as verbose intermediate refer subclause 7.17
+CSSU as verbose unsolicited refer subclause 7.17
+CTEV as verbose unsolicited refer subclause 8.10
+CTZE as verbose unsolicited refer subclause 8.41
+CTZEU as verbose unsolicited refer subclause 8.41
+CTZV as verbose unsolicited refer subclause 8.41
+CUSATEND as verbose unsolicited refer subclause 12.2.4
+CUSATP as verbose unsolicited refer subclause 12.2.4
+CUSATS as verbose unsolicited refer subclause 12.2.3
+CUSD as verbose unsolicited refer subclause 7.15
+CUUS1I as verbose intermediate refer subclause 7.26
+CUUS1U as verbose unsolicited refer subclause 7.26
+CWLANOLADI as verbose unsolicited refer subclause 10.1.39
+CWLANOLCMI as verbose unsolicited refer subclause 10.1.40
+DR as verbose intermediate refer subclause 6.26
+ILRR as verbose intermediate refer subclause 4.3
BUSY 7
final busy signal detected
CONNECT 1
intermediate connection has been established
CONNECT <text> manufacturer
specific intermediate as CONNECT but manufacturer specific
<text> gives additional information (e.g.
connection data rate)
ERROR 4
final command not accepted
NO ANSWER 8 final connection completion timeout
NO CARRIER 3 final connection terminated
NO DIALTONE 6 final no dialtone detected
OK 0
final acknowledges execution of a command line
RING 2
unsolicited incoming call signal from network
NOTE: From v6.2.0 onwards, ATV0 numeric result codes 5, 6, 7 for NO DIALTONE, BUSY and
NO ANSWER respectively, have been replaced by numeric result codes 6, 7, 8 respectively, to
be aligned with the values listed in ITU-T Recommendation V.250 [14] (previously V.25ter).
NOTE: The table B.1 is as an overview of the result codes, hence the complete syntax of the result codes is not
shown.
ETSI
ETSI TS 127 007 V13.3.0 (
2016
-
03)
313
3GPP TS 27.007 version 13.3.0 Release 13
Annex C (informative):
Commands from TIA IS-101
C.1 Introduction
The "Voice Control Interim Standard for Asynchronous DCE", TIA IS-101, contains some commands that are useful
when passing audio "data" (that is, data which represents audio information) between the computer and the TA.
Some of the following subclauses describe commands from IS-101 which are central to this TA application. However,
with the exception of necessary extensions, these descriptions are not intended to replace the definitions found in
IS-101. Other novel commands from the interim standard are not included because they are peripheral to TA operation.
NOTE 1: IS-101 also uses ITU-T Recommendation V.250 [14] AT commands, but these are not mentioned here.
The standard specifies the following modes:
- command mode, where there is no transfer of audio "data" between the TA and the computer. In command
mode, the computer is neither sending audio data to the TA nor receiving audio data from the TA.
- transmit mode, where audio "data" is being transferred from the computer to the TA. No audio "data" is
transferred from the TA to the computer in this state. A transition back to command mode occurs when an
embedded command indicates "end of play" or "flush data", or an inactivity timer times out.
- receive mode, where audio "data" is being transferred from the TA to the computer. No audio "data" is
transferred from the computer to the TA in this state. A transition back to command mode occurs when any
command is sent from the computer, or an inactivity timer times out. During the receive mode, the TA embeds
result codes into the audio "data". These result codes indicate pertanent events such as "silence detected", "busy
detected", and so on.
Strictly, the standard specifies another mode (translation), but this is not directly of interest here.
NOTE 2: The TA "knows" the type of an incoming call (whether it is voice, data, fax, whatever), and certain POTS
events cannot occur. Hence some standard result codes for indication of events and discrimination of call
type are unnecessary.
There are three possible levels of service:
- a TA supporting level A performs the following operations and detects the following events: audio transmit,
audio receive, DTMF detection, DTMF generation and single tone generation. The following indications are
supported:
Event Description Handset state
3 ring idle
4 DTMF received idle
5 receive buffer overrun receive
6 unsolicited fax request idle
8 phone on/off hook idle
9 presumed hangup receive
10 presumed end of message receive
18 ringback idle
19 busy idle
23 playback buffer underrun transmit
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
314
3GPP TS 27.007 version 13.3.0 Release 13
25 fax or data request acknowledged idle
- a TA supporting level B performs the operations and events of level A, and also supports DTMF detection while
in the transmit state.
- a TA supporting level C performs the operations and events of level B, and also supports double DTMF tone
generation.
Since DTMF detection and generation cannot be guaranteed over current digital networks, it follows that none of the
three levels of service can be supported.
C.2 Commands
C.2.1 Select mode +FCLASS
This command puts the TA into a particular mode of operation (data, fax, voice etc.). This causes the TA to process
information in a manner suitable for that type of information (rather than for other types of information). The values and
meanings of parameter <n> are specified in the following table.
<n> Mode
0 data
1 fax class 1 (TIA-578-A)
1.0 fax class 1 (ITU-T Recommendation T.31 [11])
2 fax (manufacturer specific)
2.0 fax class 2 (ITU-T Recommendation T.32 [12] and TIA-592)
3...7 reserved for other fax modes
8 voice
9...15 reserved for other voice modes
16..79 reserved
80 VoiceView (Radish)
81..255 reserved
Table C.1: +FCLASS parameter command syntax
Command
Return
+FCLASS=<n>
+FCLASS? <n>
+FCLASS=? (list of supported <n>s)
Voice mode is of particular interest here, and has an additional result code +VCON. Specifically, +VCON indicates that
the TA is entering the voice command mode and there is a voice connection to at least one audio input or output. This
presupposes that some mechanism has previously initiated a connection to that audio I/O.
C.2.2 Buffer threshold setting +VBT
This refers to integers <lo> and <hi> that indicate levels within the TA transmit buffer at which flow control is
asserted and deasserted. The buffer is used for averaging out the irregular timing of data from the computer, so that the
data becomes synchronous and may be sent to some audio device.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
315
3GPP TS 27.007 version 13.3.0 Release 13
Table C.2: +VBT parameter command syntax
Command
Return
+VBT=<lo>,<hi>
+VBT? <lo>,<hi>
+VBT=? (list of supported <lo>s),(list of supported <hi>s),(buffer size)
C.2.3 Calling number ID presentation +VCID
The command refers to an integer that allows a called party to enable or disable (<n>=0) the reporting of the ID of
calling parties, and specifies the method of presentation of the ID. This is basically the same as GSM/UMTS
supplementary service CLIP (Calling Line Identification Presentation). The presentation may be either formatted
(<n>=1) or unformatted (<n>=2):
- Formatted presentation: data items are reported in the form of <tag>=<value> pairs.
<tag> <value>
DATE MMDD (month, day)
TIME HHMM (hour, minute)
NMBR calling number or P or O (P = number is private, O = number is unavailable)
NAME subscription listing name
MESG data from other (unknown) tags
- Unformatted presentation: the data is presented in ASCII hex as printable numbers.
Table C.3: +VCID parameter command syntax
Command
Return
+VCID=<n>
+VCID? <n>
+VCID=? (0-2)
C.2.4 Receive gain selection +VGR
This refers to the amplification by the TA of audio samples sent from the TA to the computer. The command operates
on an integer <n>, range 0...255. Values larger than 128 indicate a larger gain than nominal. Values less than 128
indicate a smaller gain than nominal. The entire range of 0...255 does not have to be provided. A value of zero implies
the use of automatic gain control by the TA.
Table C.4: +VGR parameter command syntax
Command
Return
+VGR=<n>
+VGR? <n>
+VGR=? (list of supported <n>s)
C.2.5 Transmit gain selection +VGT
This refers to the amplification by the TA of audio samples sent from the computer to the TA. The command operates
on an integer <n>, range 0...255. Values larger than 128 indicate a larger gain than nominal. Values less than 128
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
316
3GPP TS 27.007 version 13.3.0 Release 13
indicate a smaller gain than nominal. The entire range of 0...255 does not have to be provided. A value of zero implies
the uses of automatic gain control by the TA.
Table C.5: +VGT parameter command syntax
Command
Return
+VGT=<n>
+VGT? <n>
+VGT=? (list of supported <n>s)
C.2.6 Initialise voice parameters +VIP
This recalls manufacturer determined settings <n> of voice parameters. The command is write only. The effect of the
command is manufacturer specific.
Table C.6: +VIP action command syntax
Command
Return
+VIP=<n>
+VIP=? (list of supported <n>s)
C.2.7 Inactivity timer +VIT
This refers to the value of the inactivity timer in the TA. It is used to monitor activity on the connection between the
computer and the TA when the computer is in "transmit" mode and sending audio data to the TA. When the connection
has been inactive for the time set by this command, the TA leaves "transmit" mode and reverts to command mode. An
integer <n> different than zero implies a time of <n>/10 seconds. A value of zero disables the timer.
Table C.7: +VIT parameter command syntax
Command
Return
+VIT=<n>
+VIT? <n>
+VIT=? (list of supported <n>s)
C.2.8 Line selection +VLS
This determines the selection of sources and destinations of audio samples. An integer is used to label a particular
combination of sources and destinations. The integer is defined in an entry in IS-101 which assumes as a model a TA, a
local phone and a phone line. Two additional "manufacturer specific" configurations (16,17) are defined.
- label=0: this is the idle state - the phone is not connected to the radio network and no audio paths are used.
- label=1: the phone is connected to the radio network and no audio paths involving the internal microphone or
internal loudspeaker are selected. This allows the computer to transmit audio data over the radio transmitter by
selecting "transmit mode":
Table C.8: +VLS label 1a
loudspeaker
computer i/p
transmit stage
microphone -->
computer o/p --> *
receiver stage -->
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
317
3GPP TS 27.007 version 13.3.0 Release 13
This also allows the computer to receive audio data from the radio receiver by selecting "receive mode":
Table C.9: +VLS label 1b
loudspeaker
computer i/p
transmit stage
microphone -->
computer o/p -->
receiver stage --> *
- label=4: the phone is not connected to the radio network but there is an audio path to the internal speaker. This
allows the computer to play sound by selecting "transmit mode".
Table C.10: +VLS label 4
loudspeaker
computer i/p
transmit stage
microphone -->
computer o/p --> *
receiver stage -->
- label=6: the phone is not connected to the radio network but there is an audio path to the internal microphone.
This allows the computer to record sound by selecting "receive mode".
Table C.11: +VLS label 6
loudspeaker
computer i/p
transmit stage
microphone --> *
computer o/p -->
receiver stage -->
- label=7: the phone is connected to the radio network. The internal microphone is connected to the radio
transmitter. The radio receiver is connected to the internal loudspeaker. This allows the computer to enable
normal phone operation (a human holding a conversation) by selecting command mode.
Table C.12: +VLS label 7
loudspeaker
computer i/p
transmit stage
microphone --> *
computer o/p -->
receiver stage --> *
Table C.13: +VLS parameter command syntax
Command
Return
+VLS=<n> +VCON
+VLS? <n>
+VLS=? complex; refer IS-101
+VCON is returned if an audio path is established or if a connection is made to the radio network.
Manufacturer specific extension (reserved as such by IS-101)
- label=16: the phone is connected to the radio network. There is a path to the internal microphone, which is also
connected to the radio transmitter. There is a path to the radio receiver, which is also connected to the internal
loudspeaker. This allows the computer to record the sum of transmitted and received audio by selecting "receive
mode".
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
318
3GPP TS 27.007 version 13.3.0 Release 13
Table C.14: +VLS label 16
loudspeaker
computer i/p
transmit stage
microphone --> * *
computer o/p -->
receiver stage --> * *
- label=17: the phone is connected to the radio system and there is a path to the internal loudspeaker and to the
radio transmitter. This allows the computer to simultaneously play sound and send audio over the radio by
selecting "transmit mode".
Table C.15: +VLS label 17
loudspeaker
computer i/p
transmit stage
microphone -->
computer o/p --> * *
receiver stage -->
C.2.9 Receive data state +VRX
This action command causes the TA to get audio data from a source determined by the +VLS command, and send it to
the computer. Once the datastream has started, any result codes will be embedded in the data and shielded using the
normal <DLE> methods. The receive process is terminated when the computer sends any command to the TA, or by
time-out of the inactivity timer. The command is write only.
Table C.16: +VRX action command syntax
Command
Return
+VRX
CONNECT
C.2.10 Select compression method +VSM
This selects the voice compression method <n1>, the voice sampling rate <n2>, the silence compression sensitivity
<n3>, and a parameter related to silence expansion <n4>. There are several choices of compression method. IS-101
does not specify methods, but here is a list of some usual compression methods:
Name Communications system
GSM/full-rate GSM
GSM/half-rate GSM
ADPCM/G.721 DECT, CT2
ADPCM/G.723 DECT, CT2
ADPCM/G.726 DECT, CT2
ADPCM/G.727 DECT, CT2
SIGNED PCM POTS
Table C.17: +VSM parameter command syntax
Command
Return
+VSM=<n1>,<n2>,<n3>,<n4>
+VSM? <n1>,<n2>,<n3>,<n4>
+VSM=? complex; refer IS-101
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
319
3GPP TS 27.007 version 13.3.0 Release 13
NOTE: A value of <n3>=0 implies no silence compression sensitivity. A value of <n4>=0 implies no silence
expansion.
C.2.11 DTMF and tone generation +VTS
This command allows the transmission of DTMF tones and arbitrary tones (see NOTE 1). These tones may be used (for
example) when announcing the start of a recording period. The command is write only. In this profile of commands,
this command does not operate in data or fax modes of operation (+FCLASS=0,1,2-7).
NOTE 1: D is used only for dialling.
The string parameter of the command consists of combinations of the following separated by commas:
1. <DTMF>. A single ASCII character in the set 0-9, #,*,A-D. This is interpreted as a single ACSII character whose
duration is set by the +VTD command.
NOTE 2: In GSM this operates only in voice mode.
2. [<tone1>,<tone2>,<duration>]. This is interpreted as a dual tone of frequencies <tone1> and <tone2>,
lasting for a time <duration> (in 10 ms multiples).
NOTE 3: This does not operate in GSM.
3. {<DTMF>,<duration>}. This is interpreted as a DTMF tone of different duration from that mandated by the
+VTD command.
NOTE 4: In GSM this operates only in voice mode.
Table C.18: +VTS action command syntax
Command
Return
+VTS=as above
+VTS=?
(list of supported <tone1>s),(list of supported
<tone2>s),(list of supported <duration>s)
C.2.12 Tone duration +VTD
This refers to an integer <n> that defines the length of tones emitted as a result of the +VTS command. This does not
affect the D command. A value different than zero causes a tone of duration <n>/10 seconds. The value zero causes a
"manufacturer specific" value.
Table C.19: +VTD parameter command syntax
Command
Return
+VTD=<n>
+VTD? <n>
+VTD=? (list of supported <n>s)
NOTE: In GSM/UMTS the value of tone duration is preset and cannot be altered.
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
320
3GPP TS 27.007 version 13.3.0 Release 13
C.2.13 Transmit data state +VTX
This action command causes the TA to receive audio data from the computer and send it to a destination determined by
the +VLS command. Once the audio datastream has started, commands to the TA shall be embedded in the data stream,
and shielded using the normal <DLE> methods. The transmit process is terminated by the use of embedded commands
or by the time-out of an inactivity timer. It is recommended that the TA has a buffer to allow the TA to convert
potentially bursty data from the computer into synchronous data for "transmission". The command is write only.
Table C.20: +VTX action command syntax
Command
Return
+VTX
CONNECT
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
321
3GPP TS 27.007 version 13.3.0 Release 13
Annex D (informative):
Bibliography
Informative references:
1) IrDA Serial Infrared Physical Layer Specification.
IrDA Serial Infrared MAC and Link Protocol.
IrDA Serial Infrared Link Access Protocol.
2) PCCA STD-101 Annex I: Data Transmission Systems and Equipment - Serial Asynchronous
Automatic Dialling and Control for Character Mode DCE on Wireless Data Services - Annex I:
Command Extensions for Analog Cellular Data Modems.
3) TIA IS-101 Facsimile Digital Interfaces - Voice Control Interim Standard for Asynchronous DCE.
4) TIA-578-A Facsimile Digital Interfaces - Asynchronous Facsimile DCE Control Standard, Service
Class 1.
5) TIA-592 Facsimile Digital Interfaces - Asynchronous Facsimile DCE Control Standard, Service
Class 2.
6) TIA-617 Data Transmission Systems and Equipment - In-Band DCE Control.
7) ITU-T Recommendation V.80: In-band DCE control and synchronous data modes for
asynchronous DTE.
RLP negohahon failure CARRIER success success olher passwb‘e laxlure codes m-call mudmcatiun success —> I in§all modmcatiun faHure in-caH modificahon success ‘ OK m-call mudmcalicn % ure ‘—
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
322
3GPP TS 27.007 version 13.3.0 Release 13
Annex E (informative):
Mobile originated alternating voice/data call example
Figure E.1 illustrates the possible transitions in MO BS 61 call. Responses and result codes generated by TA are in bold
face. In this example, data part of the call is asynchronous non-transparent 9600 bps service.
Figure E.1: MO BS 61 call
VOICE
ATD (or ATA)
remote initiated
in-call modification
successful
AT+CHUP
(or ATH
or drop DTR )
remote
hangup
DATA
remote
hangup
(V.24 circuit
109 ON)
OFF-LINE
TA sets +CMOD=0
AT+CBST=7,0,1
OK
AT+COLP=1; +CR=1; +DR=1; +ILRR=1
OK
AT+CMOD=2; +FCLASS=0
OK
OFF-LINE
success
+COLP: +35812345,145
OK
connection failure
NO CARRIER
AT+CEER
+CEER: failure cause
OK
other possible failure codes
BUSY/NO ANSWER/ERROR
in-call modification success
+CR: REL ASYNC
+DR: NONE
+ILRR: 19200
CONNECT 9600
in-call modification failure
ERROR
AT+CEER
+CEER: failure cause
OK +CR: REL ASYNC
+DR: NONE
+ILRR: 19200
CONNECT 9600
AT+CHUP
OK OK
NO CARRIER NO CARRIER
ATD12345; ATD12345
RLP negotiation failure
+COLP: +35812345,145
+CR: REL ASYNC
NO CARRIER
success
+COLP: +35812345,145
+CR: REL ASYNC
+DR: NONE
+ILRR: 19200
CONNECT 9600
ATH (or drop DTR)
in-call modification success
OK
remote initiated
in-call modification
successful
in-call modification failure
ERROR
AT+CEER
+CEER: failure cause
OK
OK
success \ canfichon failure genera‘ laxlure in-caH modificahon success —> I mfiall mudmcahon failure
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
323
3GPP
TS 27.007 version 13.3.0 Release 13
Annex F (informative):
Mobile terminated voice followed by data call example
Figure F.1 illustrates the possible transitions in MT BS 81 call. Responses and result codes generated by TA are in bold
face. In this example, data part of the call is asynchronous non-transparent 9600 bps service.
Figure F.1: MT BS 81 call
VOICE
ATD (or ATA)
remote initiated
in-call modification
successful
AT+CHUP
(or ATH
or drop DTR)
remote
hangup
DATA
remote
hangup
(V.24 circuit
109 ON)
OFF-LINE
TA sets +CMOD=0
AT+CLIP=1; +CR=1; +DR=1; +ILRR=1; +CRC=1
OK
+CRING: VOICE/REL ASYNC
+CLIP: +35812345,145
AT+CMOD=3; +FCLASS=0; A
OFF-LINE
success
OK
connection failure
NO CARRIER
AT+CEER
+CEER: failure cause
OK
general failure
ERROR
in-call modification success
+CR: REL ASYNC
+DR: NONE
+ILRR: 19200
CONNECT 9600
in-call modification failure
ERROR
AT+CEER
+CEER: failure cause
OK
+CR: REL ASYNC
+DR: NONE
+ILRR: 19200
CONNECT 9600
ATH
(or AT+CHUP
or drop DTR)
OK OK
NO CARRIER NO CARRIER
general failure ERROR call setug slaned 0 connection failure success connection lailure succ 55 OK conneclien failure My general failure
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
324
3GPP TS 27.007 version 13.3.0 Release 13
Annex G (informative):
Voice call example
Figure G.1 illustrates the possible transitions in both MT and MO TS 11 calls. Responses and result codes generated by
TA are in bold face.
Figure G.1: TS 11 calls
VOICE call active
AT+CHUP
(or ATH
or drop DTR)
remote
hangup
AT+CLIP=1; +CRC=1
OK
+CRING: VOICE
+CLIP: +35812345,145
ATA
MT
success
OK
connection failure
NO CARRIER
AT+CEER
+CEER: failure cause
OK
remote busy
BUSY
general failure
ERROR
OKNO CARRIER
AT+COLP=1
OK
ATD12345;
MO with COLP
AT+COLP=0
OK
ATD12345;
MO without COLP
connection failure
NO CARRIER
AT+CEER
+CEER: failure cause
OK
success
+COLP: +35812345,145
OK
(remote ring or
other network
generated tones)
general failure
ERROR
call setup started
OK
connection failure
NO CARRIER
AT+CEER
+CEER: failure cause
OK
(no indication
on successful
call setup)
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
325
3GPP TS 27.007 version 13.3.0 Release 13
Annex H (informative):
Change history
TSG TDoc CR R
E
V
PH CAT
SUBJECT WORKITEM NEW
_VERS
T#4 TP-99118 New Creation of 3GPP 27.007 v3.0.0 out of GSM 07.07 v7.2.0 3.0.0
T#4 TP-99124 001 R99 A Additional result codes for +CLIP +CCWA TEI 3.1.0
T#4 TP-99124 002 R99 B ECSD additions EDGE 3.1.0
T#4 TP-99124 003 R99 B ECSD asymmetry (new command +CHSA) EDGE 3.1.0
T#4 TP-99146 004 R99 A Syntax error in +CHSN command TEI 3.1.0
T#4 TP-99146 005 R99 A Moving AT commands to 07.07 for 07.60 handover to SMG3 / 3GPP
TSG CN WG3 GPRS 3.1.0
T#5 TP-99177 006 R99 D ECSD AT command correction EDGE 3.2.0
T#5 TP-99177 007 R99 B Alarm functionality TEI 3.2.0
T#5 TP-99177 008 R99 B Phonebook storage TEI 3.2.0
T#5 TP-99177 009 R99 B Time Zone TEI 3.2.0
T#5 TP-99177 010 R99 B Additional result code for +CSSN TEI 3.2.0
T#5 TP-99177 011 R99 B New command for setting of Date format TEI 3.2.0
T#5 TP-99177 012 R99 B New command for Silent mode TEI 3.2.0
T#5 TP-99177 013 R99 B New command for setting of Time format TEI 3.2.0
T#5 TP-99177 014 R99 B GSM 400 Spectrum update GSM 400 3.2.0
T#5 TP-99177 015 R99 A AT command - Request GPRS service 'D' GPRS 3.2.0
T#6 TP-99237 016 R99 F Clarification to result codes for +CLIP +CCWA TEI 3.3.0
T#6 TP-99237 017 R99 B AT command for Frame Tunnelling Mode (FTM) Frame
Tunnelling
Mode
3.3.0
T#6 TP-99237 018 R99 B New AT command for application protocols activation TEI 3.3.0
T#6 TP-99237 022 R99 B Add new AT command (+CDIP) to inform the called line identification
TEI 3.3.0
T#6 TP-99237 020 R99 C Packet Domain ATD command syntax GPRS 3.3.0
T#6 TP-99237 021 R99 B Additional parameter for +CBST TEI 3.3.0
T#6 TP-99237 019 R99 B AT-commands for Enhanced QoS Support management Enhanced QoS
Support in
GPRS
3.3.0
T#7 TP-000024 024 R99 F Deletion of the AT+CPROT? read command TEI 3.4.0
T#7 TP-000024 025 R99 F Adaptations for UMTS TEI 3.4.0
T#7 TP-000024 026 R99 D References to ASCI Specifications ASCI 3.4.0
T#7 TP-000024 027 R99 D Abbreviations related to ASCI ASCI 3.4.0
T#7 TP-000024 028 R99 B Priority indication in +CLCC, List Current Calls ASCI 3.4.0
T#7 TP-000024 029 R99 B Indication of priority, sub-address, sub-address type and TS 91/TS92 in
+CRC, Cellular Result Codes ASCI 3.4.0
T#7 TP-000024 030 R99 B Commands for ASCI ASCI 3.4.0
T#7 TP-000024 031 R99 B Commands for eMLPP eMLPP 3.4.0
T#7 TP-000024 032 R99 B Example for usage of priority eMLPP 3.4.0
T#8 TP-000073 033 R99 B +CSDF,+CCLK and +CALA(4 digits for year field) TEI 3.5.0
T#8 TP-000073 034 R99 F APN presentation TEI 3.5.0
T#8 TP-000073 035 R99 F +CAJOIN also serves to join an ongoing group or a broadcast call ASCI 3.5.0
T#8 TP-000073 036 R99 F +CAULEV, the uplink status presentation in a Voice Group Call ASCI 3.5.0
T#8 TP-000073 037 R99 F CME ERROR extensions for ASCI Commands ASCI 3.5.0
T#8 TP-000073 038 R99 F Correction of the description of the +CRC ASCI 3.5.0
T#8 TP-000073 039 R99 F Definition of the abbreviation of MT ASCI 3.5.0
T#8 TP-000073 040 R99 F Packet Domain QoS AT-commands TEI 3.5.0
T#9 TP-000143 041 R99 F TE software implementations must take account of extra parameters TEI 3.6.0
T#9 TP-000143 042 R99 F APN presentation TEI 3.6.0
T#9 TP-000144 043 R00 B Introduction of a new AT command +CUUS1 to manage User-to-User
Information element ASCI 4.0.0
T#9 TP-000144 044 R00 B Indication of priority and/or sub-address in the unsolicited result code
CCWA ASCI 4.0.0
T#9 TP-000144 045 R00 B eMLPP SIM Commands ASCI 4.0.0
T#9 TP-000144 046 R00 B VBS, VGCS SIM Commands ASCI 4.0.0
T#9 TP-000144 047 R00 A Extension of dial command for VBS and VGCS ASCI 4.0.0
T#9 TP-000144 048 R00 A Introduction of a new AT command +COTDI to manage Originator-to-
dispatcher information element ASCI 4.0.0
T#11 TP-010028 053 Rel-4 A Clarification of the specification to incorporate UICC/USIM references
TI-ATC 4.1.0
T#11 TP-010028 054 Rel-4 F Update the AT command, +CPBS, that select the phonebooks in the
SIM/UICC TI-ATC 4.1.0
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
326
3GPP TS 27.007 version 13.3.0 Release 13
T#11 TP-010028 055 Rel-4 F Correction of GSM references TI-ATC 4.1.0
T#11 TP-010028 056 Rel-4 F Update the AT commands that access the PLMN preferred list in the
SIM/UICC TI-ATC 4.1.0
T#11 TP-010028 057 Rel-4 F Update of phonebook AT commands, +CBBS,+CPBR, +CPBF and
+CPBW, to access the hidden phonebook entries TI-ATC 4.1.0
T#11 TP-010028 058 Rel-4 A Addition of explicit subscribed value to QoS command TI-ATC 4.1.0
T#11 TP-010028 059 Rel-4 A Corresponding GMM states for +CGREG command TI-ATC 4.1.0
T#11 TP-010028 060 Rel-4 F Definition of "class C in GPRS and circuit switched alternate mode" TI-ATC 4.1.0
T#12 TP-010127 061 Rel-4 A Aligning command AT+CSNS with changes introduced to single
numbering scheme TEI4 4.2.0
T#12 TP-010127 064 Rel-4 A Inclusion of multimedia values to command AT+CBST TEI4 4.2.0
T#12 TP-010127 066 Rel-4 A Modification to Request Packet Domain service 'D' command TEI4 4.2.0
T#12 TP-010127 068 Rel-4 A Inclusion of IPv6 and removal of X.25 and OSPIH <PDP_type> values
TEI4 4.2.0
T#14 TP-010269 070 1 Rel-4 A Obsolete +CGCLOSP and corrections due to IHOSS and OSP removal TI-ATC 4.3.0
T#14 TP-010269 072 Rel-4 A Obsolete +CGCLPAD and correstions due to X.25 removal TI-ATC 4.3.0
T#14 TP-010269 074 Rel-4 A Clarifications to AT commands used with circuit swiched data TI-ATC 4.3.0
T#14 TP-010269 076 Rel-4 A Correction in the +CGACT command explanation TI-ATC 4.3.0
T#14 TP-010269 077 Rel-4 F Correction of chapter heading and references TI-ATC 4.3.0
T#14 TP-010269 079 Rel-4 A Different compression algorithms in AT commands +CGDCONT and
+CGDSCONT TI-ATC 4.3.0
T#14 TP-010269 080 Rel-5 B New AT command +CRMC (Ring Melody Control) TEI5 5.0.0
T#14 TP-010269 081 Rel-5 B Added reference to 23.227 TEI5 5.0.0
T#15 TP-020014 084 Rel-5 A Alignment of UE architecture with 23.101 TEI5 5.1.0
T#16 TP-020103 085 Rel-6 B Enhancement of AT command +CIND to indicate SMS rejection TEI6 6.0.0
T#17 TP-020272 089 Rel-6 A Clarification in the behaviour of AT+W46 TEI6 6.1.0
T#19 TP-030067 097 1 Rel-6 A Clarification in the behaviour of AT+CGCLASS TEI6 6.2.0
T#19 TP-030037 101 Rel-6 A Correction ATV0 result codes TEI6 6.2.0
T#19 TP-030071 105 1 Rel-6 A Correction of AT+WS46 parameter values TEI6 6.2.0
T#19 TP-030037 109 Rel-6 A AT +CGEQREQ - Required Parameters for Streaming / Conversational
Traffic Class TEI6 6.2.0
T#20 TP-030113 110 Rel-6 F Correction of references TEI6 6.3.0
T#21 TP-030212 111 Rel-6 A Adding reference to 24.008 for the 3G QoS AT-commands TEI5 6.4.0
T#24 TP-040134 116 1 Rel-6 C Updating error codes description to support UICC TEI6 6.5.0
T#25 TP-040170 117 Rel-6 F Correction to AT command +CHSN HSCSD 6.6.0
T#25 TP-040170 118 Rel-6 B Support of logical channels in AT commands TEI6 6.6.0
T#26 TP-040225 120 Rel-6 A Additional parameter for AT command +CRSM (Restricted SIM
access) TEI5 6.7.0
T#26 TP-040225 122 Rel-6 A Corrections to AcTs of PLMN Selection TEI5 6.7.0
T#26 TP-040225 123 Rel-6 C Improve security in UICC generic access command +CGLA TEI6 6.7.0
T#26 TP-040225 124 Rel-6 B Support of EAP authentication command TEI6 6.7.0
T#26 TP-040225 125 Rel-6 F Correction of file identification in +CRLA command TEI6 6.7.0
T#26 TP-040225 126 Rel-6 B UICC Application Discovery Command +CUAD TEI6 6.7.0
T#26 TP-040225 127 Rel-6 F Clarification on the use of PIN with (U)SIM TEI6 6.7.0
T#26 TP-040225 128 Rel-6 D Editorial modifications to +CGLA and +CRLA commands TEI6 6.7.0
T#26 TP-040225 129 Rel-6 B Add RETRIEVE DATA and SET DATA APDU commands in
+CRSM and +CRLA AT commands TEI6 6.7.0
T#26 TP-040225 130 Rel-6 B Extension of read, write and find phonebook entry commands for 3G
phonebooks TEI6 6.7.0
T#27 TP-050012 131 Rel-6 F Align time zone range of AT+CCLK (CLOCK) TEI 6.8.0
T#27 TP-050012 132 Rel-6 A Illogical response in +CGDSCONT test command ( REL 6) TEI5 6.8.0
CT#31
CP-060126 137 Rel-7 F QoS additions for the AT commands +CGEQREQ and +CGEQMIN TEI7 7.0.0
CT#32
CP-060276 0138
Rel-7 F Access technology added to AT commands +CREG and +CGREG TEI7 7.1.0
CT#32
CP-060276 0139
Rel-7 F Enhancement of parameter CI in AT commands +CREG and +CGREG
TEI7 7.1.0
CT#33
CP-060506 0140
1 Rel-7 F Support for UTF-8 in AT-command +CSCS TEI7 7.2.0
CT#35
CP-070155 0141
2 Rel-7 B Addition of preferred network in AT command TEI7 7.3.0
CT#36
CP-070371 0147
- Rel-7 A Extension of AT-command +CEAP TEI6 7.4.0
CT#36
CP-070458 0145
1 Rel-7 A Correction for AT-commands +CEAP, +CERP and +CUAD TEI6 7.4.0
CT#36
CP-070395 0144
3 Rel-8 B Introduction of the new AT command AT+CPSB TEI8 8.0.0
CT#36
CP-070395 0148
2 Rel-8 B Extension of parameter <Act> to include HSDPA- & HSUPA-
capability TEI8 8.0.0
CT#37
CP-070604 0149
3 Rel-8 C Extension for AT-commands +CPBW, +CPBF and +CPBR TEI8 8.1.0
CT#37
CP-070604 0150
3 Rel-8 B AT-command +CVMOD to set the voice call preference TEI8 8.1.0
CT#38
CP-070815 0152
2 Rel-8 B AT-commands for location handling TEI8 8.2.0
CT#39
CP-080136 0153
Rel-8 F Corrections to +CMOLRG TEI8 8.3.0
CT#40
CP-080361 0156
Rel-8 B AT command for enabling/disabling the backlight TEI8 8.4.0
CT#40
CP-080351 0158
1 Rel-8 B TCRT: Short Data Transmission during ongoing VGCS EVA 8.4.0
Editorial change: sub clauses 8.51 and 8.52 swapped 8.4.1
CT#41
CP-080536 0159
1 Rel-8 B Adding and extending AT-commands to support touch screen functions
TEI8 8.5.0
CT#41
CP-080536 0160
1 Rel-8 B Setting of display resolution and scren orientation for touch screen
functions TEI8 8.5.0
CT#41
CP-080536 0161
1 Rel-8 C AT Backlight command. CBKLT Default setting TEI8 8.5.0
CT#42
CP-080873 0162
3 Rel-8 F Corrections to +CMOLRG TEI8 8.6.0
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
327
3GPP TS 27.007 version 13.3.0 Release 13
CT#42
CP-
0808873 0163
3 Rel-8 B AT-Commands for positioning assistance TEI8 8.6.0
CT#42
CP-080866 0164
1 Rel-8 B Introduction of new RAT-type for SAE SAES 8.6.0
CT#42
CP-080866 0165
2 Rel-8 B Additional AT commands for LTE/SAE SAES 8.6.0
CT#42
CP-080872 0167
Rel-8 A Restoring default value for TE character set TEI7 8.6.0
CT#42
CP-080872 0168
2 Rel-8 A Introduction of RAC to CGREG TEI7 8.6.0
CT#43
CP-090159 0170
1 Rel-8 F Correction of AT-Commands for positioning TEI8 8.7.0
CT#43
CP-090130 0171
1 Rel-8 F Support of dedicated bearer related AT command SAES 8.7.0
CT#43
CP-090153 0172
Rel-8 B AT-command for UE modes of operation in SAE SAES-CSFB 8.7.0
CT#43
CP-090159 0174
1 Rel-8 F Corrections for +CGCLASS TEI8 8.7.0
CT#43
Rel-8 Editorial cleanup by MCC 8.7.0
CT#44
CP-090413 0178
1 Rel-8 F Adding E-UTRAN to the Current Packet Switched Bearer AT
command SAES 8.8.0
CT#44
CP-090391 0177
2 Rel-8 F Common AT Command Set for EPS and UMTS/GPRS for the PS
Domain SAES 8.8.0
CT#44
CP-090430 0175
1 Rel-9 B AT command for CNAP (Calling Name Presentation) TEI9 9.0.0
CT#44
CP-090430 0176
2 Rel-9 B AT command for COLR ( Connected Line Identfication Restriction
Status ) TEI9 9.0.0
CT#45
CP-090679 0181
Rel-9 A Corrections of AT-command for originated location request TEI8 9.1.0
CT#45
CP-090679 0183
Rel-9 A Origin for assist_data is corrected TEI8 9.1.0
CT#45
CP-090682 0184
Rel-9 B 'non-GPS' enhancements of AT-command for originated location
request TEI9 9.1.0
CT#45
CP-090682 0185
Rel-9 F Corrections to UCS2 coding of +CUSD TEI9 9.1.0
CT#45
CP-090682 0186
1 Rel-9 B New AT-commands for mobile terminated location request and
disclosure TEI9 9.1.0
CT#45
CP-090655 0188
1 Rel-9 A Correct alignment of notes for +CEREG SAES 9.1.0
CT#45
CP-090682 0189
Rel-9 B Addition of intermediate result code for +CPBW TEI9 9.1.0
CT#45
CP-090682 0190
Rel-9 B New AT-commands for administration of battery TEI9 9.1.0
CT#45
CP-090674 0192
1 Rel-9 A Corrections to +CEMODE SAES-
CSFB,SAES 9.1.0
CT#46
CP-090920 0196
Rel-9 A Correction of direction of data for +CPOS TEI8 9.2.0
CT#46
CP-090922 0197
1 Rel-9 F Correction of usage of underscore (default values) for 27.007 TEI9 9.2.0
CT#46
CP-090900 0200
1 Rel-9 A Correction of outstanding Editor's note on +WS46 SAES 9.2.0
CT#47
CP-100135 0209
2 Rel-9 D Correction of minor drafting rule issues for TS 27.007 TEI9 9.3.0
CT#47
CP-100102 0207
Rel-9 A Removal of [,<pd1>[,…[,pdN]]] in +CGDCONT TEI 9.3.0
CT#47
CP-100135 0208
Rel-9 F Clarification of parameter type for +CCHO and +CCHC TEI9 9.3.0
CT#47
CP-100131 0211
Rel-9 A Incorrect indication of AT commands as parameter commands TEI8, SAES 9.3.0
CT#47
CP-100135 0212
1 Rel-9 B +CGDEL – AT-command for deletion of non-active PDP contexts and
associated parameters TEI9 9.3.0
CT#47
CP-100135 0214
Rel-9 A Incorrect name for test command version of +CGTFTRDP SAES 9.3.0
CT#47
CP-100107 0216
Rel-9 A Correction of the packet domain event reporting +CGEV SAES 9.3.0
CT#47
CP-100135 0217
Rel-9 F The value range of <cid> for network initiated PDP contexts is
clarified TEI9 9.3.0
CT#47
CP-100145 0218
1 Rel-9 B Addition of new AT-Command related to SSAC SSAC 9.3.0
CT#47
CP-100144 0219
1 Rel-9 F Correction of AT command for emergency bearer services IMS_EMER_G
PRS_EPS 9.3.0
CT#47
Rel-9 Editorial cleanup by MCC 9.3.0
CT#48
CP-100339 0221
Rel-9 A Correction of unsolicited result codes for packet domain event
reporting SAES 9.4.0
CT#48
CP-100339 0223
Rel-9 A +CGCONTRDP, alignment of with +CGTFT and +CGTFTRDP SAES 9.4.0
CT#48
CP-100339 0228
1 Rel-9 A Description of handling a request to disconnect when only connected to
a single PDN SAES 9.4.0
CT#48
CP-100339 0230
1 Rel-9 A Support for +CGPADDR returning both IPv4 and IPv6 addresses SAES 9.4.0
CT#48
CP-100339 0232
1 Rel-9 A Clarification of relationship between CREG, CEREG and CGREG SAES 9.4.0
CT#48
CP-100355 0234
Rel-9 F Removal of remaining [,<pd1>[,…[,pdN]]] in +CGDCONT TEI9 9.4.0
CT#48
CP-100355 0238
Rel-9 F Addition of missing parameter in +CNAP TEI9 9.4.0
CT#48
CP-100371 0226
Rel-10 B Support of compressed IPv6 format in AT-commands TEI10 10.0.0
CT#48
CP-100369 0224
2 Rel-10 B Control of P-CSCF address discovery AT_IMS 10.0.0
CT#48
CP-100369 0225
1 Rel-10 B +CISRVCC and +CIREP, new AT-commands for support of SRVCC AT_IMS 10.0.0
CT#48
CP-100369 0233
1 Rel-10 B Control of IM CN Subsystem Signalling Flag AT_IMS 10.0.0
CT#49
CP-100520 0240
1 Rel-10 F Alignment of table headers with AT-command names TEI10 10.1.0
CT#49
CP-100492 0243
2 Rel-10 A AT commands for eCall eData 10.1.0
CT#49
CP-100485 0248
1 Rel-10 A Clarification of AcT parameter in CREG, CGREG and CEREG SAES 10.1.0
CT#49
CP-100571 0249
4 Rel-10 B USAT over AT AT_UICC 10.1.0
CT#49
CP-100518 0250
Rel-10 F Clarification to +COPS. TEI10 10.1.0
CT#49
CP-100520 0251
1 Rel-10 B AT command for remaining PIN retries for MT passwords, +CPINR TEI10 10.1.0
CT#49
CP-100520 0252
2 Rel-10 B AT command for supporting multiple cards installed in a ME TEI10 10.1.0
CT#49
CP-100520 0253
1 Rel-10 B AT command for Emergency Numbers +CEN TEI10 10.1.0
CT#50
CP-100763 0254
2 Rel-10 B TC-RT: Introduction of group IDs with prefix TEI10 10.2.0
CT#50
CP-100742 0256
1 Rel-10 A Correction of Table 8.58-1 for +CMTLRA TEI9 10.2.0
CT#50
CP-100763 0257
Rel-10 F Correction of terminology for result codes and alignment of Annex B TEI10 10.2.0
CT#50
CP-100757 0258
1 Rel-10 B Examples of AT-commands for USAT AT_UICC 10.2.0
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
328
3GPP TS 27.00
7 version 13.3.0 Release 13
CT#50
CP-100757 0259
1 Rel-10 C Multiple corrections to AT-commands for USAT AT_UICC 10.2.0
CT#50
CP-100757 0260
2 Rel-10 F Removal of editor's note on security mechanism for AT-commands for
USAT AT_UICC 10.2.0
CT#50
CP-100747 0262
2 Rel-10 A +CGDCONT syntax IMS_EMER_G
PRS_EPS 10.2.0
CT#50
CP-100763 0263
1 Rel-10 F +CGEV for IP address types TEI10 10.2.0
CT#50
CP-100763 0265
Rel-10 F Correction of references for +CNAP TEI10 10.2.0
CT#50
CP-100763 0266
Rel-10 F Correction of action versus parameter commands TEI10 10.2.0
CT#50
CP-100763 0267
1 Rel-10 Correction of print of the IP address format TEI10 10.2.0
CT#50
CP-100763 0268
1 Rel-10 B New AT-command for Network Emergency Bearer Services Support
+CNEM TEI10 10.2.0
CT#50
CP-100763 0270
3 Rel-10 AT command for creating connection status event TEI10 10.2.0
CT#51
CP-110197 0271
1 Rel-10 B Enhancement of +CPOS and +CPOSR for LPP, capability request and
velocity request, GLONASS and SBAS TEI10 10.3.0
CT#51
CP-110197 0272
Rel-10 B Enhancement and alignment of +CLIP, +CCWA and +CLCC when
CLI is not available TEI10 10.3.0
CT#51
CP-110197 0273
1 Rel-10 F Support of AT commands for voice TEI10 10.3.0
CT#51
CP-110188 0274
1 Rel-10 F Correction of USAT profile activation AT_UICC 10.3.0
CT#51
CP-110188 0275
1 Rel-10 B Detection of currently active SIM or USIM AT_UICC 10.3.0
CT#51
CP-110188 0277
1 Rel-10 C Modification of default profiles and write response AT_UICC 10.3.0
CT#51
CP-110188 0278
1 Rel-10 F Correction of USAT event response AT_UICC 10.3.0
CT#51
CP-110197 0279
1
Rel-10
F
Clarification of relationship between CREG, CEREG and CGREG.
Introduction of registration for EPS and non-EPS services for "SMS
only" in CREG. TEI10 10.3.0
CT#51
CP-110186 0280
1 Rel-10 B +CAVIMS, availability for voice calls with the IMS AT_IMS 10.3.0
CT#51
CP-110197 0281
Rel-10 B Addition of registeration status to CREG,CGREG, CEREG command
for emergency attached UE TEI10 10.3.0
CT#51
CP-110197 0282
2 Rel-10 B +CESQ, new AT-command on extended signal quality TEI10 10.3.0
CT#52
CP-110454 0286
Rel-10 A +CGDATA, correction of syntax TEI8 10.4.0
CT#52
CP-110461 0287
1 Rel-10 F Cleanups for WI AT_UICC AT_UICC 10.4.0
CT#52
CP-110466 0291
1 Rel-10 F CREG, CEREG and CGREG: clarification for "out of coverage" TEI10 10.4.0
CT#53
CP-110669 0292
2 Rel-10 F Clarifying the indication of availability for voice calls in the IMS and
in the PS AT_IMS 10.5.0
CT#53
CP-110695 0288
4 Rel-11 B +CGAUTH, new AT-command for definition of PDP context
authentication parameters TEI11 11.0.0
CT#53
CP-110695 0293
3 Rel-11 B Enhancements to Event Reporting due to CBS primary notifications TEI11 11.0.0
CT#53
CP-110695 0294
1 Rel-11 C Enhancing touch screen actions and events TEI11 11.0.0
CT#53
CP-110695 0295
1 Rel-11 C Enhancing supported orientations by AT command +CSO TEI11 11.0.0
CT#53
CP-110695 0296
1 Rel-11 C Enhancing the assumption that touch screen size is equal to display
screen size TEI11 11.0.0
CT#54
CP-110875 0298
Rel-11 A Corrections to +VIP TEI10 11.1.0
CT#54
CP-110865 0303
Rel-11 A +CMOLR: Third Party Address should be specified when Method
value set to 5 TEI9 11.1.0
CT#54
CP-110882 0304
1 Rel-11 C Add support for display orientation event reporting TEI11 11.1.0
CT#54
CP-110864 0308
Rel-11 A Correcting syntax of +CMER TEI8 11.1.0
CT#54
CP-110882 0309
1 Rel-11 B Introduction of a default PDP context (cid=0) TEI11 11.1.0
CT#54
CP-110881 0310
1 Rel-11 B IMS registration information, +CIREG TEI11 11.1.0
CT#54
CP-110882 0311
Rel-11 F Corrections to +CGCONTRDP and +CGSCONTRDP TEI11 11.1.0
CT#54
CP-110882 0312
Rel-11 F Addition of missing brackets to make responses optional TEI11 11.1.0
CT#54
CP-110882 0313
Rel-11 F Correction to +CRLP TEI11 11.1.0
CT#54
CP-110864 0317
1 Rel-11 A Corrections to +CGCONTRDP TEI8 11.1.0
CT#54
CP-110882 0318
Rel-11 B No More PS Data, +CNMPSD TEI11 11.1.0
CT#54
CP-110882 0319
2 Rel-11 B Setting UE Usage Setting, +CEUS TEI11 11.1.0
CT#54
CP-110882 0320
1 Rel-11 C Modifying +CGCONTRDP to indicate that connectivity is provided by
a LIPA PDN connection TEI11 11.1.0
CT#55
CP-120113 0322
Rel-11 A +CESQ=?, removal of non-existing parameter <rep> TEI10 11.2.0
CT#55
CP-120113 0324
1 Rel-11 A +CESQ, alignment of parameters with value ranges in 3GPP TSs TEI10 11.2.0
CT#55
CP-120113 0326
Rel-11 A Correction of +CSUS TEI10 11.2.0
CT#55
CP-120125 0327
1 Rel-11 F Correction of action command syntax according to V.250 TEI11 11.2.0
CT#55
CP-120125 0328
Rel-11 F Usage of AT-commands in insecure scenarios TEI11 11.2.0
CT#55
CP-120125 0329
Rel-11 F Correction of AT-command +CALCC TEI11 11.2.0
CT#55
CP-120125 0330
Rel-11 F Response to test version of AT- commands shall not be optional TEI11 11.2.0
CT#55
CP-120125 0331
1 Rel-11 C +CREG, +CGREG and +CEREG, addition of cause values TEI11 11.2.0
CT#55
CP-120125 0332
Rel-11 F Indication of optional parameter in AT-command syntax TEI11 11.2.0
CT#55
CP-120124 0333
1 Rel-11 F Clarification of SRVCC handover information in +CIREPH AT
command TEI11 11.2.0
CT#55
CP-120125 0335
Rel-11 F Alignment of descriptions for context parameters TEI11 11.2.0
CT#55
CP-120125 0337
2 Rel-11 B Setting configuration values specified in TS 24.167, +CEVDP,
+CVDP, +CMMIVT TEI11 11.2.0
CT#55
CP-120125 0338
1 Rel-11 B Adding +CASIMS: SMS using IMS support indication TEI11 11.2.0
CT#55
CP-120125 0340
Rel-11 F Correct +CREG reported status TEI11 11.2.0
CT#55
CP-120125 0342
Rel-11 F Corrections to CPNER parameters TEI11 11.2.0
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
329
3GPP TS 27.007 version 13.3.0 Release 13
CT#56
CP-120309 0343
1 Rel-11 F Alignment of response codes TEI11 11.3.0
CT#56
CP-120309 0344
Rel-11 F Removal of editor"s note for security aspects of public warning
systems in Rel-11 TEI11 11.3.0
CT#56
CP-120309 0345
Rel-11 F Response to +CNEM=? is missing TEI11 11.3.0
CT#56
CP-120309 0346
Rel-11 F Correction of value range for <QCI> TEI11 11.3.0
CT#56
CP-120309 0347
1 Rel-11 B <SS_code> added to result codes +CSSI and +CSSU TEI11 11.3.0
CT#56
CP-120309 0348
Rel-11 F Update of AT command +CMUX TEI11 11.3.0
CT#56
CP-120313 0349
2 Rel-11 F Modifications to UR code for SRVCC due to introduction of vSRVCC vSRVCC-CT 11.3.0
CT#56
CP-120309 0354
2 Rel-11 F Correction of TFT description TEI11 11.3.0
CT#56
CP-120325 0355
3 Rel-11 B AT commands for URI dialling ATURI 11.3.0
CT#56
CP-120309 0356
Rel-11 F Correction of response to +CPSB? TEI11 11.3.0
CT#57
CP-120584 0357
2 Rel-11 B +CPOS and +CPOSR, enhancementst for OTDOA TEI11 11.4.0
CT#57
CP-120604 0359
1 Rel-11 B Completion of basic dialup scenaros with +CDU ATURI 11.4.0
CT#57
CP-120584 0360
Rel-11 F Clarification of time-information elements of +CPOS TEI11 11.4.0
CT#57
CP-120604 0362
1 Rel-11 B Service URNs in AT commands ATURI 11.4.0
CT#58
CP-120794 0364
1 Rel-11 F Parameters missing for response to +CUSATE TEI11 11.5.0
CT#58
CP-120813 0365
3 Rel-11 B Addition of per-call based SS-parameters to +CDU ATURI 11.5.0
CT#58
CP-120813 0366
3 Rel-11 F Completion of AT command for hangup ATURI 11.5.0
CT#58
CP-120813 0367
3 Rel-11 B Further refinement of the call monitoring command and its responses ATURI 11.5.0
CT#58
CP-120794 0368
1 Rel-11 F Inclusion of APN aggregate maximum bit rate in +CGEQOSRDP TEI11 11.5.0
CT#58
CP-120814 0369
7 Rel-11 B Communication service indication in AT commands ATURI 11.5.0
CT#58
CP-120794 0370
Rel-11 B New method introduced for +CMOLRE TEI11 11.5.0
CT#58
CP-120794 0371
1 Rel-11 F +CGCONTRDP: support providing more or less than 2 IP addresses TEI11 11.5.0
CT#58
CP-120861 0373
3 Rel-11 B Extension of +CPOSR TEI11 11.5.0
CT#58
CP-120794 0374
1 Rel-11 B Time of day inclusion for +CPOS TEI11 11.5.0
CT#58
CP-120794 0376
1 Rel-11 F DTD corrections for +CPOS and +CPOSR TEI11 11.5.0
CT#58
CP-120813 0377
2 Rel-11 B ATURI editor"s notes ATURI 11.5.0
CT#58
CP-120795 0379
2 Rel-11 F +CEPPI: Power Preference Indication for EPS TEI11 11.5.0
CT#58
CP-120806 0380
2 Rel-11 F AT command support for rSRVCC handover rSRVCC-CT 11.5.0
CT#59
CP-130115 0378
3 Rel-11 F Enabling upper layers to deal with GPRS, EPS, VBS / VGCS and
eMLPP related errors TEI11 11.6.0
CT#59
CP-130120 0381
2 Rel-11 B Completion of presentation-related supplementary services wrt SIP-
URIs ATURI 11.6.0
CT#59
CP-130120 0382
1 Rel-11 B Completion of mid-call related SSs for SIP-URIs ATURI 11.6.0
CT#59
CP-130120 0383
Rel-11 F Corrections to +CECUG ATURI 11.6.0
CT#59
CP-130120 0386
3 Rel-11 B SDP in media profiles ATURI 11.6.0
CT#59
CP-130120 0388
1 Rel-11 F Renaming of "voice client" ATURI 11.6.0
CT#59
CP-130120 0390
1 Rel-11 B Update of media during a call ATURI 11.6.0
CT#59
CP-130129 0384
1 Rel-12 F Clarification to PDP context for emergency services TEI12 12.0.0
CT#59
CP-130129 0385
Rel-12 B New AT command - Report network error codes +CNEC TEI12 12.0.0
CT#60
CP-130234 0394
1 Rel-12 A Corrections of +CSSAC SSAC 12.1.0
CT#60
CP-130264 0395
Rel-12 B Enhancement of +CGSN TEI12 12.1.0
CT#60
CP-130264 0396
4 Rel-12 B Supported radio accesses, +CSRA TEI12 12.1.0
CT#60
CP-130264 0398
1 Rel-12 F Correction to media for SIP-URI TEI12 12.1.0
CT#60
CP-130264 0400
1 Rel-12 C MSRP as media for SIP-URI TEI12 12.1.0
CT#60
CP-130264 0401
1 Rel-12 F Minor correction for +CUSATW TEI12 12.1.0
CT#60
CP-130264 0402
2 Rel-12 B AT command for Circuit Switched Fallback Support TEI12 12.1.0
CT#60
CP-130254 0405
1 Rel-12 A Removal of Editors note for ATURI ATURI 12.1.0
CT#60
CP-130254 0407
1 Rel-12 A Missing optionality for UR-code +CMCCSS7: <CUG_index> ATURI, TEI11 12.1.0
CT#60
CP-130264 0408
Rel-12 F Alignments and corrections of descriptions and parameters TEI12 12.1.0
CT#60
CP-130254 0410
2 Rel-12 A Call Forwarding URI support ATURI 12.1.0
CT#60
CP-130264 0411
1 Rel-12 B General error extensions to +CMEE TEI12 12.1.0
CT#61
CP-130510 0413
Rel-12 F +CCSFB informative example correction TEI12 12.2.0
CT#61
CP-130502 0415
1 Rel-12 A +CDEFMP error response ATURI 12.2.0
CT#61
CP-130510 0416
Rel-12 B +CPOS and +CPOSR Enhancements for LTE ECID and OTDOA TEI12 12.2.0
CT#62
CP-130762 0417
1 Rel-12 B +CGDCONT handover indication TEI12 12.3.0
CT#62
CP-130762 0418
2 Rel-12 B New AT command to control message waiting indication TEI12 12.3.0
CT#62
CP-130762 0419
2 Rel-12 F Update of +CNMPSD AT command TEI12 12.3.0
CT#62
CP-130762 0420
1 Rel-12 F Update of +CCFC AT command TEI12 12.3.0
CT#62
CP-130762 0421
1 Rel-12 B USSI support for +CUSD TEI12 12.3.0
CT#62
CP-130762 0422
1 Rel-12 C MS initiated PDP Context Activation without PDP address TEI12 12.3.0
CT#63
CP-140059 0423
1 Rel-12 F +CCFCU time conditions TEI12, ATURI 12.4.0
CT#63
CP-140144 0425
2 Rel-12 F +CGDCONT - missing parameters for NAS signalling low priority
indications and EAB TEI12, SIMTC-
RAN_OC 12.4.0
CT#63
CP-140144 0426
1 Rel-12 F Update of AT commands accepted when MT is pending SIM PIN, SIM
PUK, or PH-SIM TEI12 12.4.0
CT#64
CP-140331 0428
1 Rel-12 F Multiple PDP context activation using +CGACT TEI12 12.5.0
CT#64
CP-140331 0429
1 Rel-12 F +CUSATD and +CUSATA alignment TEI12 12.5.0
CT#64
CP-140331 0430
2 Rel-12 F Clarifications for +CUSATD TEI12 12.5.0
CT#64
CP-140331 0432
1 Rel-12 F Message waiting indication subscription failure error code TEI12 12.5.0
CT#64
CP-140331 0434
Rel-12 F Removal of redundant "EAB override" in +CGDCONT TEI12, SIMTC-
RAN_OC 12.5.0
ETSI
E
TSI TS 127 007 V13.3.0 (2016
-
03)
330
3GPP TS 27.007 version 13.3.0 Release 13
CT#65
Rel-12 Corrupted fonts fixed by MCC 12.6.0
CT#65
CP-140662 0435
Rel-12 B AT commands in support of ACB-skip SCM_LTE-CT 12.6.0
CT#65
CP-140664 0436
Rel-12 F Remove support of CDIVN from +CCFCU TEI12 12.6.0
CT#65
CP-140664 0437
1 Rel-12 F +CPOS Modifications for OTDOA and ECID TEI12 12.6.0
CT#66
CP-140836 0438
1 Rel-12 F Misalignment of +CMWI between the AT-command syntax in the
table and the parameter description TEI12 12.7.0
CT#66
CP-140836 0439
Rel-12 F Alignment of parameter description in +CCSFB TEI12 12.7.0
CT#66
CP-140855 0440
Rel-12 F Misalignment of +CSCM between the AT-command syntax in the table
and the parameter description SCM_LTE-CT 12.7.0
CT#66
CP-140836 0441
3 Rel-12 F Updates to +CGDCONT to allow security protected transmission of
ESM information TEI12 12.7.0
CT#66
CP-140836 0442
4 Rel-12 F Clean split of 'Defined Events' between CPOS and +CPOSR TEI12 12.7.0
CT#66
CP-140836 0443
Rel-12 F Correction of ECID measurements paramters in +CPOS TEI12 12.7.0
CT#66
CP-140836 0444
Rel-12 F Modification of <Strobe> element usage in +CPOS TEI12 12.7.0
CT#66
CP-140836 0446
1 Rel-12 F AT command update for Extended TFT TEI12 12.7.0
CT#66
CP-140843 0447
2 Rel-12 B Addition of AT-commands for UE Power Saving Mode MTCe-
UEPCOP-CT 12.7.0
CT#66
CP-140850 0448
Rel-12 F Alignment of value range for QCI GCSE_LTE-CT
12.7.0
CT#66
CP-140836 0449
Rel-12 F Corrections to +CUSATW AT Command TEI12 12.7.0
CT#67
CP-150064 0456
1 Rel-12 F BeiDou System (BDS) support in +CPOS and +CPOSR positioning
commands TEI12 12.8.0
CT#67
CP-150083 0457
2 Rel-13 B +CEMBMSCFG: AT command for eMBMS Configuration TEI13 13.0.0
CT#67
CP-150083 0458
2 Rel-13 B +CEMBMSR: AT command for eMBMS Status Reporting TEI13 13.0.0
CT#67
CP-150083 0459
2 Rel-13 B +CEMBMSSRV: AT command for eMBMS Service Configuration TEI13 13.0.0
CT#67
CP-150083 0460
3 Rel-13 B +CEMBMSDATA: AT command for eMBMS Data State TEI13 13.0.0
CT#67
CP-150083 0461
3 Rel-13 B +CEMBMSCNT: AT command for eMBMS Counting Procedure TEI13 13.0.0
CT#67
CP-150083 0462
2 Rel-13 B Enhance +CGCONTRDP for MTU size indication TEI13 13.0.0
CT#67
CP-150083 0463
2 Rel-13 B Enhance +CGDCONT for MTU size discovery configuration TEI13 13.0.0
CT#68
CP-150329 0469
Rel-13 C AT Command +CTZR: enhancement to extended time zone reporting TEI13 13.1.0
CT#68
CP-150310 0471
Rel-13 A GNSS related corrections in CPOS and +CPOSR positioning
commands TEI12 13.1.0
CT#68
CP-150329 0472
1 Rel-13 B Support for WLAN Offload Indication TEI13 13.1.0
CT#68
CP-150310 0473
1 Rel-13 A Type correction for +CGDCONT TEI12 13.1.0
CT#69
CP-150529 0476
2 Rel-13 B Update to +CSCON AT command TEI13 13.2.0
CT#69
CP-150511 0478
1 Rel-13 A Missing parameter definitions and support for "Early Position Fix" in
+CPOS TEI12 13.2.0
CT#69
CP-150529 0479
1 Rel-13 B New AT command for WLAN Offload Assistance Data TEI13 13.2.0
CT#69
CP-150529 0480
1 Rel-13 B New AT command for WLAN Offload based on cell measurements TEI13 13.2.0
CT#70
CP-150719 0464
3 Rel-13 C AT command in support of Application-specific congestion control for
data communication (ACDC) ACDC-CT 13.3.0
CT#70
CP-150710 0481
1 Rel-13 F MS support of Local address in TFT indicator for +CGDCONT and
+CGCONTRDP TEI13 13.3.0
CT#70
CP-150710 0482
1 Rel-13 B +CEMBMSSAI: AT command to determine avalable eMBMS Service
Area Identities TEI13 13.3.0
CT#70
CP-150694 0484
2 Rel-13 A AT Command +CGEQOS (Define EPS quality of service): correction
of value range for CQI GCSE_LTE-CT
13.3.0
ETSI
ETSI TS 127 007 V13.3.0 (2016
-
03)
331
3GPP TS 27.007 version 13.3.0 Release 13
History
Document history
V13.3.0 March 2016 Publication