Datenblatt für WP73EB/2SRDA von Kingbright

Kl'ngbrl'ghI 61 024 10.9mm) ‘~¥—‘ 2.3(o.11)m.s 295) ‘—'\ / K \ A LED1 " + ‘ § 7 ‘ ’ A a 5.; 2% 3 3- “- a n: a 3 § * V; m / g ‘— as 5' a E g 5. 13 D o.5(o.oz)_*§f5 J L\cATHonE 3 501.235) ‘ 49-5 2.54(o.1) 2.54(o.1) RECOMMENDED PCB LAYOUT 4274? c. H]: fir J \MEBSQXA {54(01)
SPEC NO: DSAF2086 REV NO: V.6A DATE: AUG/24/2015 PAGE: 1 OF 5
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1102001998
4.8mm BI-LEVEL LED INDICATOR
Part Number: WP73EB/2SRDA Super Bright Red
Features
zPre-trimmed leads for pc board mounting.
zColors can be mixed in a single housing.
zBlack case enhances contrast ratio.
zWide viewing angle.
zHigh reliability - life measured in years.
zHousing UL rating:94V-0.
zHousing material: type 66 nylon.
zRoHS compliant.
Description
The Super Bright Red source color devices are made with
Gallium Aluminum Arsenide Red Light Emitting Diode.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
Kl'ngbrl'ghI
SPEC NO: DSAF2086 REV NO: V.6A DATE: AUG/24/2015 PAGE: 2 OF 5
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1102001998
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
Part No. Emitting Color (Material) Lens Type
Iv (mcd) [2]
@ 20mA
V
iewing
Angle [1]
Min. Typ. 2θ1/2
Super Bright Red (GaAlAs) Red Diffused
200 300
60°
*60 *150
WP73EB/2SRDA
Symbol Parameter Emitting Color Typ. Max. Units Test Conditions
λpeak Peak Wavelength Super Bright Red 655 nm IF=20mA
λD [1] Dominant Wavelength Super Bright Red 640 nm IF=20mA
Δλ1/2 Spectral Line Half-width Super Bright Red 20 nm IF=20mA
C Capacitance Super Bright Red 45 pF VF=0V;f=1MHz
VF [2] Forward Voltage Super Bright Red 1.85 2.5 V IF=20mA
IR Reverse Current Super Bright Red 10 uA VR = 5V
Parameter Values Units
Power dissipation 75 mW
DC Forward Current 30 mA
Peak Forward Current [1] 155 mA
Reverse Voltage 5 V
Operating/Storage Temperature -40°C To +85°C
Lead Solder Temperature [2] 260°C For 3 Seconds
Lead Solder Temperature [3] 260°C For 5 Seconds
SPEC NO: DSAF2086 REV NO: V.6A DATE: AUG/24/2015 PAGE: 3 OF 5
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1102001998
Super Bright Red WP73EB/2SRDA
Kl'ngbrl'ghI 5 aw King right { )2 ONTSIDELABEL IRKIHBOX Kingbright PINO:WF'7!EBxxx mvnsnpu- m; “9 sm: mx ‘ m an swam WIND: RnHSOumDIIm \\ ,/ mtg //www KInngghtUSA,CDm/AQQ\\calmnNotes
SPEC NO: DSAF2086 REV NO: V.6A DATE: AUG/24/2015 PAGE: 4 OF 5
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1102001998
PACKING & LABEL SPECIFICATIONS WP73EB/2SRDA
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
Kl'ngbrl'ghI PRECAUTIONS 1 storage conditions. a.Avmd continued exposure to the condensing moisture envrronment and keep the product away from rapid \ransihuns in ampienttemperature. o LEDs should be stored with temperature goat: and reiatiue humidity < 60%="" c="" product="" in="" the="" ongmai="" seated="" package="" is="" recommended="" to="" be="" assempied="" within="" 72="" hours="" otopemng="" product="" i"="" opened="" package="" for="" more="" than="" a="" week="" shouid="" oe="" baked="" for="" 30="" (moi-0)="" hours="" at="" as~="" tonic="" 2="" the="" lead="" pitch="" ot="" the="" led="" must="" match="" the="" pitch="" at="" the="" mounting="" hoies="" on="" the="" pcb="" during="" componehtplacemeht="" leadjormmg="" may="" be="" required="" to="" insure="" the="" lead="" pitch="" matches="" the="" hate="" pitch="" reterto="" the="" figure="" oeiow="" tor="" proper="" iead="" tormrng="" procedures="" led="" housing="" hausing="" led="" homing="" housing="" led="" housing="" j="" nate‘i="" p="" nmez="" ’05="" pcb="" 5m‘="" 045'="" max="" 0="" housihq="" "ww‘q="" led="" hmtsmg="" hausing="" hdusing="" le:="" led="" homing="" 1:3!“="" pg}:="" g="" :fia="" "="" 0"="" correct="" mounting="" method="" "="">< "="" incorrectmounting="" method="" note="" 173="" do="" not="" route="" pcb="" trace="" in="" the="" contact="" area="" between="" the="" ieadtrame="" and="" the="" pcb="" to="" preventshortcircuits="" 3="" during="" soidering.="" component="" covers="" and="" hoiders="" shouid="" leave="" ciearance="" to="" avoid="" piecing="" damaging="" stress="" on="" the="" led="" during="" soidenng="" gm="" min="" ;="" hdlde="" é="" meg="" :e="" pea="" (="" ‘3="" pcs="" ’="" a="" fl="" v="" a="" a="" u="" u="" o="" x="" 4="" the="" tip="" of="" the="" soidermg="" iron="" shouid="" nevertouch="" the="" tens="" epoxy="" 5.="" throughshoie="" leds="" are="" incompatibie="" wrth="" rettow="" soidenng.="" a="" it="" the="" led="" wih="" undergo="" muitrpie="" suldering="" passes="" ortace="" other="" processes="" where="" the="" part="" may="" he="" subjected="" to="" intense="" heat.="" piease="" check="" with="" krnghnghttorcornpatroriity="" 7="" recommended="" wave="" soidenng="" promos-="" t'cmw="" §="" §="" too="" temperature="" 4.="" notes.="" time(sec)="" 4.="" 1="" recommend="" preheat="" temperature="" at="" 105‘s="" or="" less="" tas="" measured="" wilh="" athermocoupie="" attached="" to="" the="" led="" plns)="" pnor="" to="" immersion="" in="" the="" soiderwave="" with="" a="" maximum="" soider="" bath="" temperature="" ot260°c="" 2="" peak="" wave="" soidering="" temperature="" between="" 2a5'c="" -="" 255's="" lorc!="" sec="" (5="" sec="" max)="" 3="" do="" not="" appiy="" stress="" to="" the="" epoxy="" resin="" white="" the="" temperature="" is="" above="" we="" 4.fixtures="" shouid="" not="" incur="" stress="" on="" the="" component="" when="" mounnng="" and="" during="" soidenng="" process.="" 5="" sac="" 305="" soider="" aiioy="" is="" recommended.="" 6="" no="" more="" than="" one="" wave="" soidenng="" pass.="">
SPEC NO: DSAF2086 REV NO: V.6A DATE: AUG/24/2015 PAGE: 5 OF 5
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1102001998