Designs (216)

216 Results - Page 21/22 |< < 18 19 20 21 22 > >|

TSDMTX-5V2-EVM: Dual-Mode (Qi and PMA) Wireless Charging Transmitter with QC2.0/3.0 Option

Manufacturer: Semtech Corporation

The Semtech TSDMTX-5V2-EVM is an evaluation platform for test and experimentation of a wireless charging transmitter based on the Semtech TS80000 Wireless Power Transmitter Controller, TS61001 Full-Bridge FET Driver, and TS31023 Linear Regulator. This evaluation module provides a complete system solution for both Qi and PMA standards of power transmission.

View Design

760308MP: 15W Medium Power Qi Charger

Manufacturer: Rohm Semiconductor

The ROHM-760308MP-EVK-001 Wireless Power Evaluation kit is based on the Qi specification 1.2.2 and supports the Extended Power Profile (EPP) from the Wireless Power Consortium (WPC). Receiver and transmitter are also backwards compatible with the low power mode (Baseline Power Profile).

View Design

PMP11114.2: USB Type C, 3A &amp; 1.5A Charger, 7 ~ 18V in

Manufacturer: Texas Instruments

PMP11114 is a dual port USB Type C Charger. This design takes an automotive input voltage (7V to 18V nominal, load dump to 40V). The output goes to two USB Type ports, each of these ports supplies 5V. The design supports 3A on one port and 1.5A on the other port. The DC/DC portion of the design is rated for 5A total current. The design is fully compliant with USB type C and backwards complian…

View Design

NCP1083QBCGEVB(#2): 1.25 ~ 50V @ 2.5A, 36 ~ 57Vin

Manufacturer: ON Semiconductor

The NCP1083QBCGEVB implements a PoE module that converts the power from the Ethernet cable to a lower voltage. The board also supports getting its power from and auxiliary input, in case PoE network is not available. Close to the switching MOSFET voltages on the board may exceed 200 V (@250 kHz). Temperature of board and its components may exceed 85°C during normal operation.

View Design

NCP1654PFCGEVB(#2): 390V @ 300W, 85 ~ 230VAC in

Manufacturer: ON Semiconductor

The NCP1654GEVB is a Power Factor Controller to efficiently drive Continuous Conduction Mode (CCM) step-up pre-converters. The NCP1654 allows operation in Follower Boost mode to drastically lower the pre-converter size and cost, in a straight-forward manner. The NCP1654 is a continuous conduction mode and fixed frequency controller (65kHz). The coil (650 uH) is selected to limit the peak to peak …

View Design

NCP380LMUAJAGEVB: 2.1A, 2.5 ~ 5.5V in, High-side

Manufacturer: ON Semiconductor

The NCP380 is a high-side power distribution switch designed for applications where heavy capacitive loads and short-circuits are likely to be encountered

View Design

EPC9055: 3A, 0 ~ 100V, Half H-Bridge Driver

Manufacturer: EPC

This development board is in a monolithic half bridge topology with onboard gate drives, featuring the EPC2106 eGaN

View Design

EPC9019: 20A, 0 ~ 80V, Half H-Bridge

Manufacturer: EPC

These development boards are in a half-bridge topology with onboard gate drives, featuring theEPC2015/23 and EPC2001/21 eGaN® field effect transistors (FETs).

View Design

EPC9204: 10A, 0 ~ 20V, Half H-Bridge Driver

Manufacturer: EPC

EPC9204, is 20 V, 10 A PCB-based power module featuring the 30 V EPC2111 eGaN IC for “plug and play” evaluation of the high performance gained with gallium nitride power integrated circuits.

View Design

1304: MCP73831 USB to Li-Ion/Li-Po Charger 4.2V, 500mA

Manufacturer: Adafruit Industries LLC

The Adafruit 1304 is a small form factor Lipo battery charger for use with 3.7/4.2V LiPoly/LiIon battery cells with JST style terminals and a user selected charge current of 100mA or 500mA

View Design
216 Results - Page 21/22 |< < 18 19 20 21 22 > >|